| Age | Commit message (Collapse) | Author |
|---|
|
commit 9f1f46a45a681d357d1ceedecec3671a5ae957f4 upstream.
The problem this patch solves is that the forcewake accounting
necessary for register reads is protected by dev->struct_mutex. But the
hangcheck and error_capture code need to access registers without
grabbing this mutex because we hold it while waiting for the gpu.
So a new lock is required. Because currently the error_state capture
is called from the error irq handler and the hangcheck code runs from
a timer, it needs to be an irqsafe spinlock (note that the registers
used by the irq handler (neglecting the error handling part) only uses
registers that don't need the forcewake dance).
We could tune this down to a normal spinlock when we rework the
error_state capture and hangcheck code to run from a workqueue. But
we don't have any read in a fastpath that needs forcewake, so I've
decided to not care much about overhead.
This prevents tests/gem_hangcheck_forcewake from i-g-t from killing my
snb on recent kernels - something must have slightly changed the
timings. On previous kernels it only trigger a WARN about the broken
locking.
v2: Drop the previous patch for the register writes.
v3: Improve the commit message per Chris Wilson's suggestions.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This prevents an in-kernel division by zero which happens when we are
asking for i915_chipset_val too quickly, or within a race condition
between the power monitoring thread and userspace accesses via debugfs.
The issue can be reproduced easily via the following command:
while ``; do cat /sys/kernel/debug/dri/0/i915_emon_status; done
This is particularly dangerous because it can be triggered by
a non-privileged user by just reading the debugfs entry.
This issue was also found independently by Konstantin Belousov
<kostikbel@gmail.com>, who proposed a similar patch.
Reported-by: Konstantin Belousov <kostikbel@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
So that we don't get build failures once the implicit module.h
presence is removed.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Well almost anyway. IVB has 3 planes, pipes, transcoders, and FDI
interfaces, but only 2 pipe PLLs. So two of the pipes must use the same
pipe timings (e.g. 2 DP plus one other, or two HDMI with the same mode
and one other, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
Physically-addressed hardware status pages are initialized early in
the driver load process by i915_init_phys_hws. For UMS environments,
the ring structure is not initialized until the X server starts. At
that point, the entire ring structure is re-initialized with all new
values. Any values set in the ring structure (including
ring->status_page.page_addr) will be lost when the ring is
re-initialized.
This patch moves the initialization of the status_page.page_addr value
to intel_render_ring_init_dri.
Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org
|
|
|
|
i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.
i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.
i915_driver_load also has some incorrect gotos in the error cleanup
paths:
* After failing to initialize the GTT (which cannot happen, btw,
intel_gtt_get returns a fixed (non-NULL) value), it tries to
free the uninitialized WC IO mapping. Fixed this by changing the
target from out_iomapfree to out_rmmap
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Lin Ming <ming.m.lin@intel.com>
|
|
As the enable/disable routines will be gain additional complexity in
future patches, it is necessary that all callers do not bypass the
generic interface by calling into the chipset routines directly. to do
this we make the chipset routines static, so there is no choice.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
This lets us make the various IRQ functions static and helps avoid
problems like the one fixed in "drm/i915: Use chipset-specific irq
installers" where one of the exported functions was called rather than
the chipset specific version.
This also fixes a UMS-mode bug -- the correct irq functions for IRL
and later chips were only getting loaded in the KMS path.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
When auditing the locking in i915_gem.c (for a prospective change which
I then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it.
Since one is in initial setup and the other in driver unload, I'm
guessing the mutex is not required for either; but post a patch in case
it is.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add new interrupt handling functions for Ivy Bridge.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
This makes the Ironlake+ code trivial and generally simplifies things.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Set the IRQ handling functions in driver load so they'll just be used
directly, rather than branching over most of the code in the chipset
functions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
The render P-state handling code requires reading from a GT register.
This means that FORCEWAKE must be written to, a resource which is shared
and should be protected by struct_mutex. Hence we can not manipulate
that register from within the interrupt handling and so must delegate
the task to a workqueue.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
If the outputs are active and continuing to access the GATT when we
teardown the PTEs, then there is a potential for us to hang the GPU.
The hang tends to be a PGTBL_ER with either an invalid host access or
an invalid display plane fetch.
v2: Reorder IRQ initialisation to defer until after GEM is setup.
Reported-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch> (855GM)
Tested-by: Pekka Enberg <penberg@kernel.org>
# note that this doesn't fix the underlying problem of the
PGTBL_ER and pipe underruns being reported immediately upon
init on his 965GM MacBook
Reported-and-tested-by: Rick Bramley <richard.bramley@hp.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35635
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36048
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
|
|
Added a new function which waits for the ringbuffer space to be equal to
(total - 8). This is the empty condition of the ringbuffer, and
equivalent to head==tail.
Also modified two users of this functionality elsewhere in the code.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
i915 calls the panic handler function on last close to reset the modes,
however this is a really bad idea for multi-gpu machines, esp shareable
gpus machines. So add a new entry point for the driver to just restore
its own fbcon mode.
v2: move code into fb helper, fix panic code to block mode change on
powered off GPUs.
[airlied: this hits drm core and I wrote it and it was reviewed on intel-gfx
so really I signed it off twice ;-).]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
It is trivially computable from the real physical address so no need to
store both.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
|
|
On a Thinkpad x61s, I noticed some memory corruption when
plugging/unplugging the external VGA connection. The symptoms are that
4 bytes at the beginning of a page get overwritten by zeroes.
The address of the corruption varies when rebooting the machine, but
stays constant while it's running (so it's possible to repeatedly write
some data and then corrupt it again by plugging the cable).
Further investigation revealed that the corrupted address is
(dev_priv->status_page_dmah->busaddr & 0xffffffff), ie. the beginning of
the hardware status page of the i965 graphics card, cut to 32 bits.
So it seems that for some memory access, the hardware uses only 32 bit
addressing. If the hardware status page is located >4GB, this
corrupts unrelated memory.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
Userspace has a legitimate requirement to use a delta that points to
outside of the target bo, and so we need to enable this. (As this is an
abi break, albeit a relaxation of the current restrictions, mark the change
with a new flag.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
We had some conversions over to the _PIPE macros, but didn't get
everything. So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.
[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
A lot of minor tweaks to fix the tracepoints, improve the outputting for
ftrace, and to generally make the tracepoints useful again. It is a start
and enough to begin identifying performance issues and gaps in our
coverage.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Merge important suspend and resume regression fixes and resolve the
small conflict.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
|
|
Starting with SandyBridge (though possible with earlier hacked BIOSes),
the BIOS may initialise the IGFX as secondary to a discrete GPU. Prior,
it would simply disable the integrated GPU. So we adjust our PCI class
mask to match any DISPLAY_CLASS device.
In such a configuration, the IGFX is not a primary VGA controller and
so should not take part in VGA arbitration, and the error return from
vga_client_register() is expected.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
We weren't setting up the vfunc table when initialising the old DRI
ringbuffer, leading to such OOPSes as:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<(null)>] (null)
PGD 10c441067 PUD 1185e5067 PMD 0
Oops: 0010 [#1] PREEMPT SMP
last sysfs file: /sys/class/dmi/id/chassis_asset_tag
CPU 3
Modules linked in: i915 drm_kms_helper drm fb fbdev i2c_algo_bit
cfbcopyarea video backlight output cfbimgblt cfbfillrect autofs4 ipv6
nfs lockd fscache nfs_acl auth_rpcgss sunrpc coretemp hwmon_vid mousedev
usbhid hid option usb_wwan snd_hda_codec_via asus_atk0110 atl1e
usbserial snd_hda_intel snd_hda_codec firmware_class snd_hwdep snd_pcm
snd_seq snd_timer snd_seq_device processor parport_pc thermal snd
thermal_sys parport 8250_pnp button rng_core rtc_cmos shpchp hwmon
rtc_core ehci_hcd pci_hotplug uhci_hcd soundcore tpm_tis i2c_i801
rtc_lib tpm serio_raw snd_page_alloc tpm_bios i2c_core usbcore psmouse
intel_agp sg pcspkr sr_mod evdev cdrom ext3 jbd mbcache dm_mod sd_mod
ata_piix libata scsi_mod unix
Jan 18 15:49:29 lithui kernel:
Pid: 3605, comm: Xorg Not tainted 2.6.36.2 #5 P5KPL-CM/System Product
Name
RIP: 0010:[<0000000000000000>] [<(null)>] (null)
RSP: 0018:ffff8801150d1d40 EFLAGS: 00010202
RAX: 000000000001ffff RBX: ffff88011a011b00 RCX: 000000000001a704
RDX: ffff880118566028 RSI: ffff880118566028 RDI: ffff880117876800
RBP: ffff8801150d1d48 R08: ffff8801195fe300 R09: 00000000c0086444
R10: 0000000000000001 R11: 0000000000003206 R12: ffff880117876800
R13: ffff880118566000 R14: ffff880117876820 R15: ffff8801150d1df8
FS: 00007f1038d456e0(0000) GS:ffff880001780000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000001187e7000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process Xorg (pid: 3605, threadinfo ffff8801150d0000, task
ffff88011b016e40)
Stack:
ffffffffa043b8e6 ffff8801150d1d98 ffffffffa041768b dead000000000000
<0> 0000000000000048 00007f1023f2a000 0000000000000044 0000000000000008
<0> ffff88010d26bd80 ffff880117876800 ffff8801150d1df8 ffff8801150d1ea8
Call Trace:
[<ffffffffa043b8e6>] ? intel_ring_advance+0x16/0x20 [i915]
[<ffffffffa041768b>] i915_irq_emit+0x15b/0x240 [i915]
[<ffffffffa03ea7b1>] drm_ioctl+0x1f1/0x460 [drm]
[<ffffffffa0417530>] ? i915_irq_emit+0x0/0x240 [i915]
[<ffffffff810dd8f1>] ? do_sync_read+0xd1/0x120
[<ffffffff81025b1f>] ? do_page_fault+0x1df/0x3d0
[<ffffffff810ed5c7>] do_vfs_ioctl+0x97/0x550
[<ffffffff8115c2ea>] ? security_file_permission+0x7a/0x90
[<ffffffff810edb19>] sys_ioctl+0x99/0xa0
[<ffffffff810024ab>] system_call_fastpath+0x16/0x1b
Code: Bad RIP value.
RIP [<(null)>] (null)
RSP <ffff8801150d1d40>
CR2: 0000000000000000
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Herbert Xu <herbert@gondor.apana.org.au>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29153
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=23172
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
Move code around and invoke iomem annotation in a few more places in
order to silence sparse. Still a few more iomem annotations to go...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
As has_gem is unconditionally set to true, the conditional immediately
following that assignment is superfluous.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This adds a hook after the mux is switched for the driver to reprobe
the connected outputs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
|
|
The IPS driver is designed to be able to run detached from i915 and
just not enable GPU turbo in that case, in order to avoid module
dependencies between the two drivers. This means that we don't know
what the load order between the two is going to be, and we had
previously only supported IPS after (optionally) i915, but not i915
after IPS. If the wrong order was chosen, you'd get no GPU turbo, and
something like half the possible graphics performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
The relative-to-general state default is useless as it means having to
rewrite the streaming kernels for each batch. Relative-to-surface is
more useful, as that stream usually needs to be rewritten for each
batch. And absolute addressing mode, vital if you start streaming
state, is also only available by adjusting the register...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Add frame buffer compression on Sandybridge. The method is similar to
Ironlake, except that two new registers of type GTTMMADR must be written
with the right fence info.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Immediate merge for the conflicting introduction of HAS_COHERENT_RINGS.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
include/drm/i915_drm.h
|
|
Otherwise we can't really fix the abi-braindeadness of forcing
libva to manually wait for rendering when switching rings. Which
in turn makes implementing hw semaphores a pointless exercise
(at least for ironlake).
[Also added the relaxed fencing param to explain the jump in
numbering - relaxed fencing is in -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
The bulk of the change is to convert the growing list of rings into an
array so that the relationship between the rings and the semaphore sync
registers can be easily computed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
This makes the various rings more consistent by removing the anomalous
handing of the rendering ring execbuffer dispatch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
A glorified s/obj_priv/obj/ with a net reduction of over a 100 lines and
many characters!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
... and no need to perform a linear search for the index.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
The GATT is a write-only set of registers, reading from them in the
manner of i915_gtt_to_phys() is supposed to be undefined. However a
simple solution exists as we allocate linear memory from the stolen
area, we can simply add the block offset to the base register. As a
side-effect we recover all the unused stolen GTT entries and so enlarge
our aperture.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
It isn't used for the hangcheck, which does its work right from the
timer trigger, but hangcheck can lead to error state recording, which
is run off of the workqueue.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
We only ever used the PRB0, neglecting the secondary ring buffers, and
now with the advent of multiple engines with separate ring buffers we
need to excise the anachronisms from our code (and be explicit about
which ring we mean where). This is doubly important in light of the
FORCEWAKE required to read ring buffer registers on SandyBridge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
If modeset init failed we attempted to unload the module, before we
finished setting it up and so triggered various oopses.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
After switching the MMIO registers to use pci_iomap, remember to dispose
of the mapping with pci_iounmap (for symmetry).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
So long as we adhere to the fence registers rules for alignment and no
overlaps (including with unfenced accesses to linear memory) and account
for the tiled access in our size allocation, we do not have to allocate
the full fenced region for the object. This allows us to fight the bloat
tiling imposed on pre-i965 chipsets and frees up RAM for real use. [Inside
the GTT we still suffer the additional alignment constraints, so it doesn't
magic allow us to render larger scenes without stalls -- we need the
expanded GTT and fence pipelining to overcome those...]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Eliminate the racy device unload by embedding a shrinker into each
device. Smaller, simpler code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
