| Age | Commit message (Collapse) | Author |
|---|
|
Explicitly merging these two branches due to nontrivial conflicts and
to allow further work.
Resolved Conflicts:
arch/x86/kernel/head32.c
arch/x86/kernel/head64.c
arch/x86/mm/init_64.c
arch/x86/realmode/init.c
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
We have removed the remap allocator for x86-32, and x86-64 never had
it (and doesn't need it). Remove residual reference to it.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQVn6_QZi3fNQ-JHYiR-7jeDJ5hT0SyT_%2BzVvfOj=PzF3w@mail.gmail.com
|
|
Remove reference to removed function resume_map_numa_kva().
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20130131005616.1C79F411@kernel.stglabs.ibm.com
|
|
This code was an optimization for 32-bit NUMA systems.
It has probably been the cause of a number of subtle bugs over
the years, although the conditions to excite them would have
been hard to trigger. Essentially, we remap part of the kernel
linear mapping area, and then sometimes part of that area gets
freed back in to the bootmem allocator. If those pages get
used by kernel data structures (say mem_map[] or a dentry),
there's no big deal. But, if anyone ever tried to use the
linear mapping for these pages _and_ cared about their physical
address, bad things happen.
For instance, say you passed __GFP_ZERO to the page allocator
and then happened to get handed one of these pages, it zero the
remapped page, but it would make a pte to the _old_ page.
There are probably a hundred other ways that it could screw
with things.
We don't need to hang on to performance optimizations for
these old boxes any more. All my 32-bit NUMA systems are long
dead and buried, and I probably had access to more than most
people.
This code is causing real things to break today:
https://lkml.org/lkml/2013/1/9/376
I looked in to actually fixing this, but it requires surgery
to way too much brittle code, as well as stuff like
per_cpu_ptr_to_phys().
[ hpa: Cc: this for -stable, since it is a memory corruption issue.
However, an alternative is to simply mark NUMA as depends BROKEN
rather than EXPERIMENTAL in the X86_32 subclause... ]
Link: http://lkml.kernel.org/r/20130131005616.1C79F411@kernel.stglabs.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
|
|
... and fix the following warning:
arch/x86/mm/numa.c: In function ‘setup_node_data’:
arch/x86/mm/numa.c:222:3: warning: passing argument 1 of ‘__phys_addr_nodebug’ makes integer from pointer without a cast
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1359245901-8512-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Normal boot path on system with iommu support:
swiotlb buffer will be allocated early at first and then try to initialize
iommu, if iommu for intel or AMD could setup properly, swiotlb buffer
will be freed.
The early allocating is with bootmem, and could panic when we try to use
kdump with buffer above 4G only, or with memmap to limit mem under 4G.
for example: memmap=4095M$1M to remove memory under 4G.
According to Eric, add _nopanic version and no_iotlb_memory to fail
map single later if swiotlb is still needed.
-v2: don't pass nopanic, and use -ENOMEM return value according to Eric.
panic early instead of using swiotlb_full to panic...according to Eric/Konrad.
-v3: make swiotlb_init to be notpanic, but will affect:
arm64, ia64, powerpc, tile, unicore32, x86.
-v4: cleanup swiotlb_init by removing swiotlb_init_with_default_size.
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-36-git-send-email-yinghai@kernel.org
Reviewed-and-tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.linux-foundation.org
Cc: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
We should set mappings only for usable memory ranges under max_pfn
Otherwise causes same problem that is fixed by
x86, mm: Only direct map addresses that are marked as E820_RAM
Make it only map range in pfn_mapped array.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-34-git-send-email-yinghai@kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: linux-pm@vger.kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
HPA said, we should not have RW and +x set at the time.
for kernel layout:
[ 0.000000] Kernel Layout:
[ 0.000000] .text: [0x01000000-0x021434f8]
[ 0.000000] .rodata: [0x02200000-0x02a13fff]
[ 0.000000] .data: [0x02c00000-0x02dc763f]
[ 0.000000] .init: [0x02dc9000-0x0312cfff]
[ 0.000000] .bss: [0x0313b000-0x03dd6fff]
[ 0.000000] .brk: [0x03dd7000-0x03dfffff]
before the patch, we have
---[ High Kernel Mapping ]---
0xffffffff80000000-0xffffffff81000000 16M pmd
0xffffffff81000000-0xffffffff82200000 18M ro PSE GLB x pmd
0xffffffff82200000-0xffffffff82c00000 10M ro PSE GLB NX pmd
0xffffffff82c00000-0xffffffff82dc9000 1828K RW GLB x pte
0xffffffff82dc9000-0xffffffff82e00000 220K RW GLB NX pte
0xffffffff82e00000-0xffffffff83000000 2M RW PSE GLB NX pmd
0xffffffff83000000-0xffffffff8313a000 1256K RW GLB NX pte
0xffffffff8313a000-0xffffffff83200000 792K RW GLB x pte
0xffffffff83200000-0xffffffff83e00000 12M RW PSE GLB x pmd
0xffffffff83e00000-0xffffffffa0000000 450M pmd
after patch,, we get
---[ High Kernel Mapping ]---
0xffffffff80000000-0xffffffff81000000 16M pmd
0xffffffff81000000-0xffffffff82200000 18M ro PSE GLB x pmd
0xffffffff82200000-0xffffffff82c00000 10M ro PSE GLB NX pmd
0xffffffff82c00000-0xffffffff82e00000 2M RW GLB NX pte
0xffffffff82e00000-0xffffffff83000000 2M RW PSE GLB NX pmd
0xffffffff83000000-0xffffffff83200000 2M RW GLB NX pte
0xffffffff83200000-0xffffffff83e00000 12M RW PSE GLB NX pmd
0xffffffff83e00000-0xffffffffa0000000 450M pmd
so data, bss, brk get NX ...
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-33-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
They are the same, and we could move them out from head32/64.c to setup.c.
We are using memblock, and it could handle overlapping properly, so
we don't need to reserve some at first to hold the location, and just
need to make sure we reserve them before we are using memblock to find
free mem to use.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-32-git-send-email-yinghai@kernel.org
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
During kdump kernel's booting stage, it need to find low ram for
swiotlb buffer when system does not support intel iommu/dmar remapping.
kexed-tools is appending memmap=exactmap and range from /proc/iomem
with "Crash kernel", and that range is above 4G for 64bit after boot
protocol 2.12.
We need to add another range in /proc/iomem like "Crash kernel low",
so kexec-tools could find that info and append to kdump kernel
command line.
Try to reserve some under 4G if the normal "Crash kernel" is above 4G.
User could specify the size with crashkernel_low=XX[KMG].
-v2: fix warning that is found by Fengguang's test robot.
-v3: move out get_mem_size change to another patch, to solve compiling
warning that is found by Borislav Petkov <bp@alien8.de>
-v4: user must specify crashkernel_low if system does not support
intel or amd iommu.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-31-git-send-email-yinghai@kernel.org
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Now kexeced kernel/ramdisk could be above 4g, so remove 896 limit for
64bit.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-30-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Use it to get mem size under the limit_pfn.
to replace local version in x86 reserved_initrd.
-v2: remove not needed cast that is pointed out by HPA.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-29-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
That is for bootloaders.
setup_data is in setup_header, and bootloader is copying that from bzImage.
So for old bootloader should keep that as 0 already.
old kexec-tools till now for elf image set setup_data to 0, so it is ok.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-28-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Now 64bit entry is fixed on 0x200, can not be changed anymore.
Update the comments to reflect that.
Also put info about it in boot.txt
-v2: fix some grammar error
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-27-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
xloadflags bit 1 indicates that we can load the kernel and all data
structures above 4G; it is set if kernel is relocatable and 64bit.
bootloader will check if xloadflags bit 1 is set to decide if
it could load ramdisk and kernel high above 4G.
bootloader will fill value to ext_ramdisk_image/size for high 32bits
when it load ramdisk above 4G.
kernel use get_ramdisk_image/size to use ext_ramdisk_image/size to get
right positon for ramdisk.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Rob Landley <rob@landley.net>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
We should set mappings only for usable memory ranges under max_pfn
Otherwise causes same problem that is fixed by
x86, mm: Only direct map addresses that are marked as E820_RAM
This patch exposes pfn_mapped array, and only sets ident mapping for ranges
in that array.
This patch relies on new kernel_ident_mapping_init that could handle existing
pgd/pud between different calls.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-25-git-send-email-yinghai@kernel.org
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Now ident_mapping_init is checking if pgd/pud is present for every 2M,
so several 2Ms are in same PUD, it will keep checking if pud is there
with same pud.
init_level4_page just does not check existing pgd/pud.
We could use generic mapping_init with different settings in info to
replace those two local grown version functions.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-24-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
When first kernel is booted with memmap= or mem= to limit max_pfn.
kexec can load second kernel above that max_pfn.
We need to set ident mapping for whole image in this case instead of just
for first 2M.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-23-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Now 64bit kernel supports more than 1T ram and kexec tools
could find buffer above 1T, remove that obsolete limitation.
and use MAXMEM instead.
Tested on system with more than 1024G ram.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-22-git-send-email-yinghai@kernel.org
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
commit 08da5a2ca
x86_64: Early segment setup for VT
sets up LDT and TR into a valid state in order to speed up boot
decompression under VT.
Those code are put in code64, and it is using GDT that is only
loaded from code32 path.
That breaks booting with 64bit bootloader that does not go through
code32 path and jump to startup_64 directly, and it has different
GDT.
Move those lines into code32 after their GDT is loaded.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-21-git-send-email-yinghai@kernel.org
Cc: Zachary Amsden <zamsden@gmail.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
We need to move some code to 32bit section in following patch:
x86, boot: Move lldt/ltr out of 64bit code section
but that will push startup_64 down from 0x200.
According to hpa, we can not change startup_64 position and that
is an ABI.
We could move function verify_cpu and no_longmode down, because
verify_cpu is used via function call and no_longmode will not
return, then we don't need to add extra code for jumping back.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-20-git-send-email-yinghai@kernel.org
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
boot/compressed/misc.c is used for bzImage in 64bit and 32bit, and
cmd_line_ptr could point to buffer that is above 4g, cmd_line_ptr
should be 64bit otherwise high 32bit will be capped out.
So need to change data type to unsigned long, that will be 64bit get
correct address of command line buffer.
And it is still ok with 32bit bzImage, because unsigned long on 32bit kernel
is still 32bit.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-19-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
cmdline.c::__cmdline_find_option... are shared between 16-bit setup code
and 32/64 bit decompressor code.
for 32/64 only path via kexec, we should not check if ptr is less 1M.
as those cmdline could be put above 1M, or even 4G.
Move out accessible checking out of __cmdline_find_option()
So decompressor in misc.c can parse cmdline correctly.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-18-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Add an accessor function for the command line address.
Later we will add support for holding a 64-bit address via ext_cmd_line_ptr.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-17-git-send-email-yinghai@kernel.org
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
There are several places to find ramdisk information early for reserving
and relocating.
Use accessor functions to make code more readable and consistent.
Later will add ext_ramdisk_image/size in those functions to support
loading ramdisk above 4g.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-16-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
They are the same, could move them out from head32/64.c to setup.c.
We are using memblock, and it could handle overlapping properly, so
we don't need to reserve some at first to hold the location, and just
need to make sure we reserve them before we are using memblock to find
free mem to use.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-15-git-send-email-yinghai@kernel.org
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
We are not having max_pfn_mapped set correctly until init_memory_mapping.
So don't print its initial value for 64bit
Also need to use KERNEL_IMAGE_SIZE directly for highmap cleanup.
-v2: update comments about max_pfn_mapped according to Stefano Stabellini.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-14-git-send-email-yinghai@kernel.org
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
We only map a single 2 MiB page per #PF, even though we should be able
to do this a full gigabyte at a time with no additional memory cost.
This is a workaround for a broken AMD reference BIOS (and its
derivatives in shipping system) which maps a large chunk of memory as
WB in the MTRR system but will #MC if the processor wanders off and
tries to prefetch that memory, which can happen any time the memory is
mapped in the TLB.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-13-git-send-email-yinghai@kernel.org
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
[ hpa: rewrote the patch description ]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Linear mode (CR0.PG = 0) is mutually exclusive with 64-bit mode; all
64-bit code has to use page tables. This makes it awkward before we
have first set up properly all-covering page tables to access objects
that are outside the static kernel range.
So far we have dealt with that simply by mapping a fixed amount of
low memory, but that fails in at least two upcoming use cases:
1. We will support load and run kernel, struct boot_params, ramdisk,
command line, etc. above the 4 GiB mark.
2. need to access ramdisk early to get microcode to update that as
early possible.
We could use early_iomap to access them too, but it will make code to
messy and hard to be unified with 32 bit.
Hence, set up a #PF table and use a fixed number of buffers to set up
page tables on demand. If the buffers fill up then we simply flush
them and start over. These buffers are all in __initdata, so it does
not increase RAM usage at runtime.
Thus, with the help of the #PF handler, we can set the final kernel
mapping from blank, and switch to init_level4_pgt later.
During the switchover in head_64.S, before #PF handler is available,
we use three pages to handle kernel crossing 1G, 512G boundaries with
sharing page by playing games with page aliasing: the same page is
mapped twice in the higher-level tables with appropriate wraparound.
The kernel region itself will be properly mapped; other mappings may
be spurious.
early_make_pgtable is using kernel high mapping address to access pages
to set page table.
-v4: Add phys_base offset to make kexec happy, and add
init_mapping_kernel() - Yinghai
-v5: fix compiling with xen, and add back ident level3 and level2 for xen
also move back init_level4_pgt from BSS to DATA again.
because we have to clear it anyway. - Yinghai
-v6: switch to init_level4_pgt in init_mem_mapping. - Yinghai
-v7: remove not needed clear_page for init_level4_page
it is with fill 512,8,0 already in head_64.S - Yinghai
-v8: we need to keep that handler alive until init_mem_mapping and don't
let early_trap_init to trash that early #PF handler.
So split early_trap_pf_init out and move it down. - Yinghai
-v9: switchover only cover kernel space instead of 1G so could avoid
touch possible mem holes. - Yinghai
-v11: change far jmp back to far return to initial_code, that is needed
to fix failure that is reported by Konrad on AMD systems. - Yinghai
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-12-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
After we switch to use #PF handler help to set page table, init_level4_pgt
will only have entries set after init_mem_mapping().
We need to move copying init_level4_pgt to trampoline_pgd after that.
So split reserve and setup, and move the setup after init_mem_mapping()
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-11-git-send-email-yinghai@kernel.org
Cc: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
with #PF handler way to set early page table, level3_ident will go away with
64bit native path.
So just use entries in init_level4_pgt to set them in trampoline_pgd.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-10-git-send-email-yinghai@kernel.org
Cc: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
We want to support struct boot_params (formerly known as the
zero-page, or real-mode data) above the 4 GiB mark. We will have #PF
handler to set page table for not accessible ram early, but want to
limit it before x86_64_start_reservations to limit the code change to
native path only.
Also we will need the ramdisk info in struct boot_params to access the microcode
blob in ramdisk in x86_64_start_kernel, so copy struct boot_params early makes
it accessing ramdisk info simple.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-9-git-send-email-yinghai@kernel.org
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
It is simple version for kernel_physical_mapping_init.
it will work to build one page table that will be used later.
Use mapping_info to control
1. alloc_pg_page method
2. if PMD is EXEC,
3. if pgd is with kernel low mapping or ident mapping.
Will use to replace some local versions in kexec, hibernation and etc.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-8-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Trampoline code is executed by APs with kernel low mapping on 64bit.
We need to set trampoline code to EXEC early before we boot APs.
Found the problem after switching to #PF handler set page table,
and we do not set initial kernel low mapping with EXEC anymore in
arch/x86/kernel/head_64.S.
Change to use early_initcall instead that will make sure trampoline
will have EXEC set.
-v2: Merge two comments according to Borislav Petkov <bp@alien8.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-7-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Just like the way we calculate next for pud and pmd, aka round down and
add size.
Also, do not do boundary-checking with 'next', and just pass 'end' down
to phys_pud_init() instead. Because the loop in phys_pud_init() stops at
PTRS_PER_PUD and thus can handle a possibly bigger 'end' properly.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-6-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Separate out the reservation of the kernel static memory areas into a
separate function.
Also add support for case when memmap=xxM$yyM is used without exactmap.
Need to remove reserved range at first before we add E820_RAM
range, otherwise added E820_RAM range will be ignored.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-5-git-send-email-yinghai@kernel.org
Cc: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
During debugging loading kernel above 4G, found that one page is not used
in pre-allocated BRK area for early page allocation.
pgt_buf_top is address that can not be used, so should check if that new
end is above that top, otherwise last page will not be used.
Fix that checking and also add print out for allocation from pre-allocated
BRK area to catch possible bugs later.
But after we get back that page for pgt, it tiggers one bug in pgt allocation
with xen: We need to avoid to use page as pgt to map range that is
overlapping with that pgt page.
Add checking about overlapping, when it happens, use memblock allocation
instead. That fixes crash on Xen PV guest with 2G that Stefan found.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-2-git-send-email-yinghai@kernel.org
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Coming patches to x86/mm2 require the changes and advanced baseline in
x86/boot.
Resolved Conflicts:
arch/x86/kernel/setup.c
mm/nobootmem.c
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Use the new sentinel field to detect bootloaders which fail to follow
protocol and don't initialize fields in struct boot_params that they
do not explicitly initialize to zero.
Based on an original patch and research by Yinghai Lu.
Changed by hpa to be invoked both in the decompression path and in the
kernel proper; the latter for the case where a bootloader takes over
decompression.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Define the 2.12 bzImage boot protocol: add xloadflags and additional
fields to allow the command line, initramfs and struct boot_params to
live above the 4 GiB mark.
The xloadflags now communicates if this is a 64-bit kernel with the
legacy 64-bit entry point and which of the EFI handover entry points
are supported.
Avoid adding new read flags to loadflags because of claimed
bootloaders testing the whole byte for == 1 to determine bzImageness
at least until the issue can be researched further.
This is based on patches by Yinghai Lu and David Woodhouse.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Originally-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
|
|
The opened file should be closed.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Cc: Kusanagi Kouichi <slash@ac.auone-net.jp>
Cc: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1358183628-27784-1-git-send-email-dinggnu@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In short, it is illegal to call __pa() on an address holding
a percpu variable. This replaces those __pa() calls with
slow_virt_to_phys(). All of the cases in this patch are
in boot time (or CPU hotplug time at worst) code, so the
slow pagetable walking in slow_virt_to_phys() is not expected
to have a performance impact.
The times when this actually matters are pretty obscure
(certain 32-bit NUMA systems), but it _does_ happen. It is
important to keep KVM guests working on these systems because
the real hardware is getting harder and harder to find.
This bug manifested first by me seeing a plain hang at boot
after this message:
CPU 0 irqstacks, hard=f3018000 soft=f301a000
or, sometimes, it would actually make it out to the console:
[ 0.000000] BUG: unable to handle kernel paging request at ffffffff
I eventually traced it down to the KVM async pagefault code.
This can be worked around by disabling that code either at
compile-time, or on the kernel command-line.
The kvm async pagefault code was injecting page faults in
to the guest which the guest misinterpreted because its
"reason" was not being properly sent from the host.
The guest passes a physical address of an per-cpu async page
fault structure via an MSR to the host. Since __pa() is
broken on percpu data, the physical address it sent was
bascially bogus and the host went scribbling on random data.
The guest never saw the real reason for the page fault (it
was injected by the host), assumed that the kernel had taken
a _real_ page fault, and panic()'d. The behavior varied,
though, depending on what got corrupted by the bad write.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212435.4905663F@kernel.stglabs.ibm.com
Acked-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
This is necessary because __pa() does not work on some kinds of
memory, like vmalloc() or the alloc_remap() areas on 32-bit
NUMA systems. We have some functions to do conversions _like_
this in the vmalloc() code (like vmalloc_to_page()), but they
do not work on sizes other than 4k pages. We would potentially
need to be able to handle all the page sizes that we use for
the kernel linear mapping (4k, 2M, 1G).
In practice, on 32-bit NUMA systems, the percpu areas get stuck
in the alloc_remap() area. Any __pa() call on them will break
and basically return garbage.
This patch introduces a new function slow_virt_to_phys(), which
walks the kernel page tables on x86 and should do precisely
the same logical thing as __pa(), but actually work on a wider
range of memory. It should work on the normal linear mapping,
vmalloc(), kmap(), etc...
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212433.4D1FCA62@kernel.stglabs.ibm.com
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
try_preserve_large_page() can be slightly simplified by using
the new page_level_*() helpers. This also moves the 'level'
over to the new pg_level enum type.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212432.14F3D993@kernel.stglabs.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
I plan to use lookup_address() to walk the kernel pagetables
in a later patch. It returns a "pte" and the level in the
pagetables where the "pte" was found. The level is just an
enum and needs to be converted to a useful value in order to
do address calculations with it. These helpers will be used
in at least two places.
This also gives the anonymous enum a real name so that no one
gets confused about what they should be passing in to these
helpers.
"PTE_SHIFT" was chosen for naming consistency with the other
pagetable levels (PGD/PUD/PMD_SHIFT).
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212431.405D3A8C@kernel.stglabs.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The KVM code has some repeated bugs in it around use of __pa() on
per-cpu data. Those data are not in an area on which using
__pa() is valid. However, they are also called early enough in
boot that __vmalloc_start_set is not set, and thus the
CONFIG_DEBUG_VIRTUAL debugging does not catch them.
This adds a check to also verify __pa() calls against max_low_pfn,
which we can use earler in boot than is_vmalloc_addr(). However,
if we are super-early in boot, max_low_pfn=0 and this will trip
on every call, so also make sure that max_low_pfn is set before
we try to use it.
With this patch applied, CONFIG_DEBUG_VIRTUAL will actually
catch the bug I was chasing (and fix later in this series).
I'd love to find a generic way so that any __pa() call on percpu
areas could do a BUG_ON(), but there don't appear to be any nice
and easy ways to check if an address is a percpu one. Anybody
have ideas on a way to do this?
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212430.F46F8159@kernel.stglabs.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The __pa() fixup series that follows touches KVM code that is not
present in the existing branch based on v3.7-rc5, so merge in the
current upstream from Linus.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
ssh://ra.kernel.org/pub/scm/linux/kernel/git/tip/tip into x86/mm
Add missing patch from the __pa_symbol conversion series by Alexander
Duyck.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Pull kvm fixlet from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Emulate dcbf
|
|
Pull ARM fixes from Russell King:
"A number of fixes:
Patrik found a problem with preempt counting in the VFP assembly
functions which can cause the preempt count to be upset.
Nicolas fixed a problem with the parsing of the DT when it straddles a
1MB boundary.
Subhash Jadavani reported a problem with sparsemem and our highmem
support for cache maintanence for DMA areas, and TI found a bug in
their strongly ordered memory mapping type.
Also, three fixes by way of Will Deacon's tree from Dave Martin for
instruction compatibility and Marc Zyngier to fix hypervisor boot mode
issues."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7629/1: mm: Fix missing XN flag for for MT_MEMORY_SO
ARM: DMA: Fix struct page iterator in dma_cache_maint() to work with sparsemem
ARM: 7628/1: head.S: map one extra section for the ATAG/DTB area
ARM: 7627/1: Predicate preempt logic on PREEMP_COUNT not PREEMPT alone
ARM: virt: simplify __hyp_stub_install epilog
ARM: virt: boot secondary CPUs through the right entry point
ARM: virt: Avoid bx instruction for compatibility with <=ARMv4
|
