| Age | Commit message (Collapse) | Author |
|---|
|
mn10300 doesn't provide its own atomic64 implementation, so it should pull
in the generic one.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
SNB graphics devices have a bug that prevent them from accessing certain
memory ranges, namely anything below 1M and in the pages listed in the
table. So reserve those at boot if set detect a SNB gfx device on the
CPU to avoid GPU hangs.
Stephane Marchesin had a similar patch to the page allocator awhile
back, but rather than reserving pages up front, it leaked them at
allocation time.
[ hpa: made a number of stylistic changes, marked arrays as static
const, and made less verbose; use "memblock=debug" for full
verbosity. ]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Some systems compile in both ARMv6 and ARMv7 into multiplatform
configurations. This means the default compiler flags are for ARMv6,
and we will get:
arch/arm/mach-mvebu/coherency_ll.S: Assembler messages:
arch/arm/mach-mvebu/coherency_ll.S:45: Error: selected processor does not support `dsb'
Fix this by specifying ARMv7 flags for coherency_ll.o.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Integrator/AP syscon remapping was done in the .setup()
function rather than .preinit() which is wrong - .preinit()
is called before .setup() and the former also use the syscon
base and cause a crash since it was not yet remapped.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
mvebu fixes for v3.8-rc3
- gpio fixes in mvebu, kirkwood, and dove
- small DT fix for mvebu (correct RAM size)
* tag 'mvebu_fixes_for_v3.8-rc3' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: Fix memory size for Armada 370 DB
ARM: Dove: add Cubox sdhci card detect gpio
ARM: Kirkwood: fix ns2 gpios by converting to pinctrl
arm: mvebu: use global interrupts for GPIOs on Armada XP
|
|
Commit 68b2532 (ARM: imx: select HAVE_IMX_SRC when SMP is enabled)
introduces a build error with imx_v6_v7_defconfig when CONFIG_SMP is
deselected.
LINK vmlinux
LD vmlinux.o
MODPOST vmlinux.o
GEN .version
CHK include/generated/compile.h
UPD include/generated/compile.h
CC init/version.o
LD init/built-in.o
arch/arm/mach-imx/built-in.o: In function `imx6q_restart':
platform-ahci-imx.c:(.text+0x448c): undefined reference to `imx_src_prepare_restart'
arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
platform-ahci-imx.c:(.text+0x4544): undefined reference to `imx_set_cpu_jump'
arch/arm/mach-imx/built-in.o: In function `imx6q_init_irq':
platform-ahci-imx.c:(.init.text+0xbef0): undefined reference to `imx_src_init'
make[1]: *** [vmlinux] Error 1
While the commit adds 'def_bool y if SMP' for HAVE_IMX_SRC, it should
not remove 'select HAVE_IMX_SRC' from SOC_IMX6Q, as the IMX6Q UP build
also needs HAVE_IMX_SRC. Add the HAVE_IMX_SRC select back for SOC_IMX6Q
to fix above build error.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Ensure that the aux table is properly initialized, even when optional features
are missing. Without this, the FDPIC loader did not work. This was meant to
be included in commit d5ab780305bb6d60a7b5a74f18cf84eb6ad153b1.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
b4265f12340f809447b9a48055e88c444b480c89
(mm: use vm_unmapped_area() on sh architecture)
broke sh boot. This patch define TASK_UNMAPPED_BASE
as a page aligned constant to solve this issue.
Special thanks to Michel
Acked-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
__hyp_stub_install duplicates quite a bit of safe_svcmode_maskall
by forcing the CPU back to SVC. This is unnecessary, as
safe_svcmode_maskall is called just after.
Furthermore, the way we build SPSR_hyp is buggy as we fail to mask
the interrupts, leading to interesting behaviours on TC2 + UEFI.
The fix is to simply remove this code and rely on safe_svcmode_maskall
to do the right thing.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Reported-by: Harry Liebel <harry.liebel@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Secondary CPUs should use the __hyp_stub_install_secondary entry
point, so boot mode inconsistencies can be detected.
Cc: <stable@vger.kernel.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
Reported-by: Ian Molton <ian.molton@collabora.co.uk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Non-T variants of ARMv4 do not support the bx instruction.
However, __hyp_stub_install is always called from the same
instruction set used to build the bulk of the kernel, so bx should
not be necessary.
This patch uses the traditional "mov pc" instead of bx.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
[will: fixed up remaining bx instruction]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
commit b080935c8638e08134629d0a9ebdf35669bec14d
kvm: Directly account vtime to system on guest switch
also removed the irq_disable/enable around kvm guest switch, which
is correct in itself. Unfortunately, there is a BUG ON that (correctly)
checks for preemptible to cover the call to rcu later on.
(Introduced with commit 8fa2206821953a50a3a02ea33fcfb3ced2fd9997
KVM: make guest mode entry to be rcu quiescent state)
This check might trigger depending on the kernel config.
Lets make sure that no preemption happens during kvm_guest_enter.
We can enable preemption again after the call to
rcu_virt_note_context_switch returns.
Please note that we continue to run s390 guests with interrupts
enabled.
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
CC: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Actually the Armada 370 DB (aka DB-88F6710-BP-DDR3) come with 1GB and
not 512MB.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Pull KVM bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: use dynamic percpu allocations for shared msrs area
KVM: PPC: Book3S HV: Fix compilation without CONFIG_PPC_POWERNV
powerpc: Corrected include header path in kvm_para.h
Add rcu user eqs exception hooks for async page fault
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Add the finit_module system call, fix the irq statistics in
/proc/stat, fix a s390dbf lockdep problem, a patch revert for a
problem that is not 100% understood yet, and a few patches to
fix warnings."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: define read*_relaxed functions
s390/topology: export cpu_topology
s390/pm: export pm_power_off
s390/pci: define isa_dma_bridge_buggy
s390/3215: partially revert tty close handling fix
s390/irq: count cpu restart events
s390/irq: remove split irq fields from /proc/stat
s390/irq: enable irq sum accounting for /proc/stat again
s390/syscalls: wire up finit_module syscall
s390/pci: remove dead code
s390/smp: fix section mismatch for smp_add_present_cpu()
s390/debug: Fix s390dbf lockdep problem in debug_(un)register_view()
|
|
|
|
This patch is brought to you by the letter 'H'.
Commit 20b279 breaks compatiblity with older perf binaries when run with
precise modifier (:p or :pp) by requiring the exclude_guest attribute to be
set. Older binaries default exclude_guest to 0 (ie., wanting guest-based
samples) unless host only profiling is requested (:H modifier). The workaround
for older binaries is to add H to the modifier list (e.g., -e cycles:ppH -
toggles exclude_guest to 1). This was deemed unacceptable by Linus:
https://lkml.org/lkml/2012/12/12/570
Between family in town and the fresh snow in Breckenridge there is no time left
to be working on the proper fix for this over the holidays. In the New Year I
have more pressing problems to resolve -- like some memory leaks in perf which
are proving to be elusive -- although the aforementioned snow is probably why
they are proving to be elusive. Either way I do not have any spare time to work
on this and from the time I have managed to spend on it the solution is more
difficult than just moving to a new exclude_guest flag (does not work) or
flipping the logic to include_guest (which is not as trivial as one would
think).
So, two options: silently force exclude_guest on as suggested by Gleb which
means no impact to older perf binaries or revert the original patch which
caused the breakage.
This patch does the latter -- reverts the original patch that introduced the
regression. The problem can be revisited in the future as time allows.
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Link: http://lkml.kernel.org/r/1356749767-17322-1-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This is mostly a port of dbf62d50067e ("ARM: mm: introduce L_PTE_VALID
for page table entries") and 26ffd0d43b18 ("ARM: mm: introduce present,
faulting entries for PAGE_NONE") from ARM, which makes use of present,
faulting page table entries for page table entries mapped as PROT_NONE.
The main difference with this implementation is that we can make use of
the two pte type bits in order to avoid allocating a software bit for
identifying PROT_NONE pages, instead reserving the 10b suffix for these
types of mappings.
This is required to prevent users from accessing such pages via syscalls
such as read/write over a pipe.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Marking non-present ptes as read-only can corrupt file ptes, breaking
things like swap and file mappings.
This patch ensures that we only manipulate user pte bits when the pte
is marked present.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch is an arm64 version of ce73ec6db47a ("powerpc/vdso: Remove
redundant locking in update_vsyscall_tz()").
Timezone data is not protected, so the sequence counter is not required
to ensure consistency. Furthermore, having multiple paths updating the
counter leads to a race between update_vsyscall and update_vsyscall_tz,
so remove the timezone sequence counting from both the kernel and the
vdso.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Card detect for sdhci on Cubox is connected to the wrong pin
(sdio1_cd instead of sdio0_cd). With support for cd-gpios and
pinctrl add the corresponding properties to DT for Cubox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Note that the pinctrl conversion also fixes GPIO support for ns2 boards.
Since commit f9e75922: "ARM: Kirkwood: Make use of mvebu pincltl and
gpio", the mvbu_gpio driver is used for DT boards. As mvbu_gpio relies
on the pinctrl driver, then a pinctrl definition must be given to allow
the GPIO configuration.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7616/1: cache-l2x0: aurora: Use writel_relaxed instead of writel
ARM: 7615/1: cache-l2x0: aurora: Invalidate during clean operation with WT enable
ARM: 7614/1: mm: fix wrong branch from Cortex-A9 to PJ4b
ARM: 7612/1: imx: Do not select some errata that depends on !ARCH_MULTIPLATFORM
ARM: 7611/1: VIC: fix bug in VIC irqdomain code
ARM: 7610/1: versatile: bump IRQ numbers
ARM: 7609/1: disable errata work-arounds which access secure registers
ARM: 7608/1: l2x0: Only set .set_debug on PL310 r3p0 and earlier
|
|
Retract back most macro definitions which went into the
user-visible mce.h header. Even though those bits are mostly
hardware-defined/-architectural, their naming is not. If we export them
to userspace, any kernel unification/renaming/cleanup cannot be done
anymore since those are effectively cast in stone. Besides, if userspace
wants those definitions, they can write their own defines and go crazy.
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
The biggest change is a fix to deal with different power state
on omap2 registers that causes issues trying to use common PM code.
Also fix few incorrect registers, and an issue for omap1 USB, and
few sparse fixes for issues that sneaked in with all the clean-up.
* tag 'omap-for-v3.8-rc2/fixes-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
ARM: OMAP1: fix USB configuration use-after-release
ARM: OMAP2/3: PRM: fix bogus OMAP2xxx powerstate return values
ARM: OMAP3: clock data: Add missing enable/disable for EMU clock
ARM: OMAP4: PRM: Correct wrong instance usage for reading reset sources
ARM: OMAP4: PRM: fix RSTTIME and RSTST offsets
ARM: OMAP4: PRM: Correct reset source map
ARM: OMAP: SRAM: resolve sparse warnings
ARM: OMAP AM33xx: hwmod data: resolve sparse warnings
ARM: OMAP: 32k counter: resolve sparse warnings
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Most of them are EXYNOS5440 fixes which are for changing uart console,
cpu id (typo) and silent complaining gpio error in kernel boot.
* 'v3.8-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: skip the clock initialization for exynos5440
ARM: EXYNOS: enable PINCTRL for EXYNOS5440
ARM: dts: use uart port1 for console on exynos4210-smdkv310
ARM: dts: use uart port0 for console on exynos5440-ssdk5440
ARM: SAMSUNG: fix the cpu id for EXYNOS5440
ARM: EXYNOS: Revise HDMI resource size
|
|
into fixes
From Shawn Guo:
I have to send one critical mxsfb fix through arm-soc, as FB maintainer
is unresponsive for quite a while. People start complaining the missing
of such an important fix.
* tag 'mxs-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
video: mxsfb: fix crash when unblanking the display
ARM: dts: imx23-olinuxino: Fix IOMUX settings
|
|
into fixes
From Shawn Guo:
It includes one critical fix - wrong flexcan2 clock will hang system
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
* tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mx5: Fix MX53 flexcan2 clock
ARM: dts: imx31-bug: Fix manufacturer compatible string
clk: imx: Remove 'clock-output-names' from the examples
|
|
Use dynamic percpu allocations for the shared msrs structure,
to avoid using the limited reserved percpu space.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
The Armada XP GPIO controller has two ways of notifying interrupts:
using global interrupts or using per-CPU interrupts. In an attempt to
use the best available features, the 'marvell,armadaxp-gpio'
compatible string selects a variant of the gpio-mvebu driver that
makes use of the per-CPU interrupts.
Unfortunately, this doesn't work properly in a SMP context, because we
fall into cases where the GPIO interrupt is enabled on CPU X at the
GPIO controller level, but on CPU Y at the interrupt controller
level. It is not yet clear how to fix that easily.
So for 3.8, our approach is to switch to global interrupts for GPIOs,
so that we do not fall into this per-CPU interrupts problem.
This patch therefore fixes GPIO interrupts on Armada XP
platforms. Without this patch, GPIO interrupts simply do not work
reliably, because their proper operation depends on which CPU the code
requesting the interrupt is running.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch fixes some code that implements a work-around to a hardware bug in
the ac97 controller on the pxa27x. A bug in the controller's warm reset
functionality requires that the mfp used by the controller as the AC97_nRESET
line be temporarily reconfigured as a generic output gpio (AF0) and manually
held high for the duration of the warm reset cycle. This is what was done in
the original code, but it was broken long ago by commit fb1bf8cd
([ARM] pxa: introduce processor specific pxa27x_assert_ac97reset())
which changed the mfp to a GPIO input instead of a high output.
The fix requires the ac97 controller to obtain the gpio via gpio_request_one(),
with arguments that configure the gpio as an output initially driven high.
Tested on a palm treo 680 machine. Reportedly, this broken code only prevents a
warm reset on hardware that lacks a pull-up on the line, which appears to be the
case for me.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
Just map the read*_relaxed() functions to their corresponding read*() functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Export cpu_topology symbol, so it's available for modules.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Export pm_power_off symbol. Needed by at least one of the new device
drivers that come with CONFIG_PCI.
And all other architectures export that symbol as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Define isa_dma_bridge_buggy. Needed to make pci quirks compile:
drivers/pci/quirks.c: In function ‘quirk_isa_dma_hangs’:
drivers/pci/quirks.c:88:7: error: ‘isa_dma_bridge_buggy’ undeclared (first use in this function)
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Count CPU Restart events and make them visible via /proc/interrupts.
Every CPU hotplug (online) event will increase the per cpu counter.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Now that irq sum accounting for /proc/stat's "intr" line works again we
have the oddity that the sum field (first field) contains only the sum
of the second (external irqs) and third field (I/O interrupts).
The reason for that is that these two fields are already sums of all other
fields. So if we would sum up everything we would count every interrupt
twice.
This is broken since the split interrupt accounting was merged two years
ago: 052ff461c8427629aee887ccc27478fc7373237c "[S390] irq: have detailed
statistics for interrupt types".
To fix this remove the split interrupt fields from /proc/stat's "intr"
line again and only have them in /proc/interrupts.
This restores the old behaviour, seems to be the only sane fix and mimics
a behaviour from other architectures where /proc/interrupts also contains
more than /proc/stat's "intr" line does.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
For more than two years, since f2c66cd8eeddedb440f33bc0f5cec1ed7ae376cb
"/proc/stat: scalability of irq num per cpu" the output of /proc/stat is
broken.
The first field in the "intr" line should contain the sum of all interrupts,
however since the above mentioned change it is always zero.
The reason for that is that a per cpu irq sum variable had been introduced
which got incremented when calling kstat_incr_irqs_this_cpu(). However
on s390 we directly incremented only the per cpu per irq counter by accessing
the array element via kstat_cpu(smp_processor_id()).irqs[...].
So fix this and use the kstat_incr_irqs_this_cpu() wrapper which increments
both: the per cpu per irq counter and the per cpu irq sum counter.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Get rid of these:
arch/s390/pci/pci_dma.c:16:29: warning: ‘zpci_ioat_dt’ defined but not used [-Wunused-variable]
arch/s390/pci/pci.c:164:12: warning: ‘zpci_store_fib’ defined but not used [-Wunused-function]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Fixes this section mismatch:
WARNING: vmlinux.o(.text+0x145e4): Section mismatch in reference from the function
smp_add_present_cpu() to the function .cpuinit.text:register_cpu()
The function smp_add_present_cpu() references
the function __cpuinit register_cpu().
This is often because smp_add_present_cpu lacks a __cpuinit
annotation or the annotation of register_cpu is wrong.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The debug_register/unregister_view() functions call debugfs_remove()
while holding the debug_info spinlock. Because debugfs_remove() takes
a mutex and therefore can sleep this is not allowed. To fix the problem
we give up the debug_info lock before calling debugfs_remove().
The following shows the lockdep message:
[ INFO: possible circular locking dependency detected ]
-------------------------------------------------------
rmmod/4379 is trying to acquire lock:
(&sb->s_type->i_mutex_key#2){+.+.+.}, at: [<00000000003acae2>] debugfs_remove+0x5e/0xa
but task is already holding lock:
(&(&rc->lock)->rlock){-.-...}, at: [<000000000010a5ae>] debug_unregister_view+0x3a/0xd
which lock already depends on the new lock.
-> #0 (&sb->s_type->i_mutex_key#2){+.+.+.}:
[<00000000001b1644>] validate_chain+0x880/0x1154
[<00000000001b4d6c>] __lock_acquire+0x414/0xc44
[<00000000001b5c16>] lock_acquire+0xbe/0x178
[<0000000000614016>] mutex_lock_nested+0x66/0x36c
[<00000000003acae2>] debugfs_remove+0x5e/0xac
[<000000000010a620>] debug_unregister_view+0xac/0xd0
[<000003ff8002f140>] qeth_core_exit+0x48/0xf08 [qeth]
[<00000000001c35a4>] SyS_delete_module+0x1a4/0x260
[<0000000000618134>] sysc_noemu+0x22/0x28
[<000003fffd4704da>] 0x3fffd4704da
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
commit c045e3f13 (ARM: imx: include iram.h rather than mach/iram.h) changed the
location of iram.h, which causes the following build error when building the coda
driver:
drivers/media/platform/coda.c:27:23: error: mach/iram.h: No such file or directory
drivers/media/platform/coda.c: In function 'coda_probe':
drivers/media/platform/coda.c:2000: error: implicit declaration of function 'iram_alloc'
drivers/media/platform/coda.c:2001: warning: assignment makes pointer from integer without a cast
drivers/media/platform/coda.c: In function 'coda_remove':
drivers/media/platform/coda.c:2024: error: implicit declaration of function 'iram_free'
Since the content of iram.h is not imx specific, move it to
include/linux/platform_data/imx-iram.h instead. This is an intermediate solution
until the i.MX iram allocator is converted to the generic SRAM allocator.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
fixes for mvebu/kirkwood v3.8
- use correct uart driver for mvebu boards
- add a missing DT clocks
- gpio-poweroff level vs. edge triggering, use gpio_is_valid()
- remove an inappropriate __init, modules need to access function.
- various DT fixes
- error handling in mv_xor
* tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux:
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
Power: gpio-poweroff: Fix documentation and gpio_is_valid
ARM: Kirkwood: Fix missing clk for USB device.
arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
I mismerged a previous branch from Alexander, and accidentally left
in ARCH_USES_GETTIMEOFFSET. Remove it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Alexander Shiyan <shc_work@mail.ru>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into fixes
From Linus Walleij:
Two fixes to the Nomadik:
- Delete a dangling include
- Bump IRQ numbers to offset at 32
* tag 'nomadik-fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: bump the IRQ numbers again
ARM: nomadik: delete dangling include
|
|
This fixes suspend to RAM adding necessary save and restore of L2 and GIC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When we fail to power down, we need to clear out the power request.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
With commit 384a290 (ARM: gic: use a private mapping for CPU target
interfaces), wake-up IPIs now go to all cores as the gic cpu interface
numbering may not follow core numbering. This broke secondary boot on
highbank since the boot address was already set for all secondary cores,
this caused all cores to boot before the kernel was ready.
Fix this by moving the setting of the jump address to
highbank_boot_secondary instead of highbank_smp_prepare_cpus and
highbank_cpu_die. Also, clear the address when we boot. This prevents
cores from booting before they are actually triggered and is also necessary
to get suspend/resume to work.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
