| Age | Commit message (Collapse) | Author |
|---|
|
After commit ec2212088c42 ("Disintegrate asm/system.h for Alpha"), the
fpu.h header which we install for userland started depending on
special_insns.h which is not installed.
However, fpu.h only uses that for __KERNEL__ code, so protect the
inclusion the same way to avoid build breakage in glibc:
/usr/include/asm/fpu.h:4:31: fatal error: asm/special_insns.h: No such file or directory
Cc: stable@vger.kernel.org
Reported-by: Matt Turner <mattst88@gentoo.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit d065bd810b6d ("mm: retry page fault when blocking on disk
transfer") and 37b23e0525d3 ("x86,mm: make pagefault killable")
introduced changes into the x86 pagefault handler for making the page
fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial during OOM
killer invocation.
Port these changes to ALPHA.
Signed-off-by: Mohd. Faris <mohdfarisq2010@gmail.com>
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
New helper: current_thread_info(). Allows to do a bunch of odd syscalls
in C. While we are at it, there had never been a reason to do
osf_getpriority() in assembler. We also get "namespace"-aware (read:
consistent with getuid(2), etc.) behaviour from getx?id() syscalls now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Similar to x86/sparc/powerpc implementations except:
1) we implement an extremely efficient has_zero()/find_zero()
sequence with both prep_zero_mask() and create_zero_mask()
no-operations.
2) Our output from prep_zero_mask() differs in that only the
lowest eight bits are used to represent the zero bytes
nevertheless it can be safely ORed with other similar masks
from prep_zero_mask() and forms input to create_zero_mask(),
the two fundamental properties prep_zero_mask() must satisfy.
Tests on EV67 and EV68 CPUs revealed that the generic code is
essentially as fast (to within 0.5% of CPU cycles) of the old
Alpha specific code for large quadword-aligned strings, despite
the 30% extra CPU instructions executed. In contrast, the
generic code for unaligned strings is substantially slower (by
more than a factor of 3) than the old Alpha specific code.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add sys_process_vm_readv and sys_process_vm_writev to Alpha.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently we export SOCK_NONBLOCK to user space but that conflicts with
the definition from glibc leading to compilation errors in user programs
(e.g. see Debian bug #658460).
The generic socket.h restricts the definition of SOCK_NONBLOCK to the
kernel, as does the MIPS specific socket.h, so let's do the same on
Alpha.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM fixes from Russell King:
"The largest thing in this set of changes is bringing back some of the
ARMv3 code to fix a compile problem noticed on RiscPC, which we still
support, even though we only support ARMv4 there.
(The reason is that the system bus doesn't support ARMv4 half-word
accesses, so we need the ARMv3 library code for this platform.)
The rest are all quite minor fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7490/1: Drop duplicate select for GENERIC_IRQ_PROBE
ARM: Bring back ARMv3 IO and user access code
ARM: 7489/1: errata: fix workaround for erratum #720789 on UP systems
ARM: 7488/1: mm: use 5 bits for swapfile type encoding
ARM: 7487/1: mm: avoid setting nG bit for user mappings that aren't present
ARM: 7486/1: sched_clock: update epoch_cyc on resume
ARM: 7484/1: Don't enable GENERIC_LOCKBREAK with ticket spinlocks
ARM: 7483/1: vfp: only advertise VFPv4 in hwcaps if CONFIG_VFPv3 is enabled
ARM: 7482/1: topology: fix section mismatch warning for init_cpu_topology
|
|
Some of the arguments to {g,s}etsockopt are passed in userland pointers.
If we try to use the 64bit entry point, we end up sometimes failing.
For example, dhcpcd doesn't run in x32:
# dhcpcd eth0
dhcpcd[1979]: version 5.5.6 starting
dhcpcd[1979]: eth0: broadcasting for a lease
dhcpcd[1979]: eth0: open_socket: Invalid argument
dhcpcd[1979]: eth0: send_raw_packet: Bad file descriptor
The code in particular is getting back EINVAL when doing:
struct sock_fprog pf;
setsockopt(s, SOL_SOCKET, SO_ATTACH_FILTER, &pf, sizeof(pf));
Diving into the kernel code, we can see:
include/linux/filter.h:
struct sock_fprog {
unsigned short len;
struct sock_filter __user *filter;
};
net/core/sock.c:
case SO_ATTACH_FILTER:
ret = -EINVAL;
if (optlen == sizeof(struct sock_fprog)) {
struct sock_fprog fprog;
ret = -EFAULT;
if (copy_from_user(&fprog, optval, sizeof(fprog)))
break;
ret = sk_attach_filter(&fprog, sk);
}
break;
arch/x86/syscalls/syscall_64.tbl:
54 common setsockopt sys_setsockopt
55 common getsockopt sys_getsockopt
So for x64, sizeof(sock_fprog) is 16 bytes. For x86/x32, it's 8 bytes.
This comes down to the pointer being 32bit for x32, which means we need
to do structure size translation. But since x32 comes in directly to
sys_setsockopt, it doesn't get translated like x86.
After changing the syscall table and rebuilding glibc with the new kernel
headers, dhcp runs fine in an x32 userland.
Oddly, it seems like Linus noted the same thing during the initial port,
but I guess that was missed/lost along the way:
https://lkml.org/lkml/2011/8/26/452
[ hpa: tagging for -stable since this is an ABI fix. ]
Bugzilla: https://bugs.gentoo.org/423649
Reported-by: Mads <mads@ab3.no>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Link: http://lkml.kernel.org/r/1345320697-15713-1-git-send-email-vapier@gentoo.org
Cc: H. J. Lu <hjl.tools@gmail.com>
Cc: <stable@vger.kernel.org> v3.4..v3.5
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Pull C6X atomic64 support from Mark Salter:
"Enable atomic64 ops in C6X
- define L1_CACHE_SHIFT
- select GENERIC_ATOMIC64"
* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
C6X: select GENERIC_ATOMIC64
C6X: add Lx_CACHE_SHIFT defines
|
|
If P2M leaf is completly packed with INVALID_P2M_ENTRY or with
1:1 PFNs (so IDENTITY_FRAME type PFNs), we can swap the P2M leaf
with either a p2m_missing or p2m_identity respectively. The old
page (which was created via extend_brk or was grafted on from the
mfn_list) can be re-used for setting new PFNs.
This also means we can remove git commit:
5bc6f9888db5739abfa0cae279b4b442e4db8049
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back
which tried to fix this.
and make the amount that is required to be reserved much smaller.
CC: stable@vger.kernel.org # for 3.5 only.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Previous attempts to add platform probing of the Audio related devices
only call from non-DT initialisation functions. This patch extends that
functionality to the Device Tree related ones too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The platform attempts to register platform device 'snd_soc_u8500'
which doesn't actually exist. Here we change the reference to the
correct one 'snd_soc_mop500'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
2ec8663f9c03a96f2c328c7c483603c31d62ad37 (lmo) rsp.
497e5ff03f58583ada469db8a1aa34eced9dd63e (kernel.org) [MIPS: Malta: Move
PIIX4 PCI fixup to where it belongs.] attempted to move this PCI fixup
but really only added it at it's new location without deleting the old
instance.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The ath79 platform code allows to run a single kernel image on various
SoCs which are based on the 24Kc and 74Kc cores. The current code
explicitely disables the DSP ASE, but that is available in the 74Kc core.
Remove the override in order to let the kernel to detect the availability
of the DSP ASE at runtime.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The current implementation of synchronise_count_{master,slave} blocks
slave CPUs in early boot until all of them come up. This no longer
works because blocking a CPU with interrupts off after notifying the
CPU to be online causes problems with the current kernel.
Specifically, after the workqueue changes
(commit a08489c569dc1 "Pull workqueue changes from Tejun Heo")
the CPU_ONLINE notification callback workqueue_cpu_up_callback()
will hang on wait_for_completion(&idle_rebind.done), if the slave
CPUs are blocked for synchronize_count_slave().
The changes are to update synchronize_count_{master,slave}() to handle
one CPU at a time and to call synchronise_count_master() in __cpu_up()
so that the CPU_ONLINE notification goes out only after the COP0 COUNT
register is synchronized.
[ralf@linux-mips.org: This matter only to those few platforms which are
using the cp0 counter as their clocksource which are XLP, XLR and MIPS'
CMP solution.]
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
BCM6338 and BCM6348 have a message control register width of 8 bits, instead
of 16-bits like what the SPI driver assumes right now. Also the SPI message
type shift value of 14 is actually 6 for these SoCs.
This resulted in transmit FIFO corruption because we were writing 16-bits
to an 8-bits wide register, thus spanning on the first byte of the transmit
FIFO, which had already been filed in bcm63xx_spi_fill_txrx_fifo().
Fix this by passing the message control register width and message type
shift through platform data back to the SPI driver so that it can use
it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Cc: jonas.gorski@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3983/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In case a series of R_MIPS_HI16 relocations was not followed by an
R_MIPS_LO16 relocation we were leaking the hi16 relocation chain.
Handle that error and return an error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The relocation code was essentially taken from the 2.4 modutils which
perform relocation in userspace. In 2.6 relocation of multiple modules
may be performed in parallel by the in-kernel loader so the global
variable mips_hi16_list won't fly anymore. Fix race by moving it into
mod_arch_specific.
[ralf@linux-mips.org: folded in Tony's followup fix. Thanks Tony!]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/4189/
|
|
Commit 6f5d2e970452b5c86906adcb8e7ad246f535ba39 (lmo) /
477c4b07406357ad93d0e32788dbf3ee814eadaa (kernel.org) [[MIPS: VPE: Free
relocation chain on error.] fixed the same issue in the vpe loader in 2009
but back then the same bug in module.c went unfixed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Akhilesh Kumar <akhilesh.lxr@gmail.com>
|
|
Without this udelay(1) PCI idsel does not work correctly on the
"singleboard" (T-Mobile Surfbox) for the MiniPCI device. The result is
that PCI configuration fails and the MiniPCI card is not detected
correctly. Instead of
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
We see only the CardBus device:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x40000fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40001000-0x40001fff]
Later the device driver shows this error:
ath5k 0000:00:03.0: cannot remap PCI memory region
ath5k: probe of 0000:00:03.0 failed with error -5
I assume that the logic chip which usually supresses the signal to the CardBus
card has some settling time and without the delay it would still let the
Cardbus interfere with the response from the MiniPCI card.
What I cannot explain is why this behaviour shows up now and not in earlier
kernel versions before. Maybe older PCI code was slower?
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: linux-mips@linux-mips.org
Cc: manuel.lauss@googlemail.com
Cc: florian@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/4087/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
It is needed in order to get rid of the following errors:
arch/mips/ath79/clock.c:353:13: error: redefinition of 'clk_get'
include/linux/clk.h:281:27: note: previous definition of 'clk_get' was here
arch/mips/ath79/clock.c:377:5: error: redefinition of 'clk_enable'
include/linux/clk.h:295:19: note: previous definition of 'clk_enable' was here
arch/mips/ath79/clock.c:383:6: error: redefinition of 'clk_disable'
include/linux/clk.h:300:20: note: previous definition of 'clk_disable' was here
arch/mips/ath79/clock.c:388:15: error: redefinition of 'clk_get_rate'
include/linux/clk.h:302:29: note: previous definition of 'clk_get_rate' was here
arch/mips/ath79/clock.c:394:6: error: redefinition of 'clk_put'
include/linux/clk.h:291:20: note: previous definition of 'clk_put' was here
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4170/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The currently assigned IRQ number to the OHCI controller is incorrect for
the AR7240 SoC, and that leads to the following error message from the
OHCI driver:
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ath79-ohci ath79-ohci: Atheros built-in OHCI controller
ath79-ohci ath79-ohci: new USB bus registered, assigned bus number 1
ath79-ohci ath79-ohci: irq 14, io mem 0x1b000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new full-speed USB device number 2 using ath79-ohci
ath79-ohci ath79-ohci: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
Fix this by using the correct IRQ number.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The AR724[12] SoCs have more GPIO lines than the AR7240.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Cc: linux-mips@linux-mips.org
Patchwork: https://http://patchwork.linux-mips.org/patch/4167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Since 3.6.0-rc1, We are getting many messages like:
WARNING: at kernel/irq/irqdomain.c:444 irq_domain_associate_many+0x23c/0x260()
Modules linked in:
Call Trace:
[<ffffffff814cb698>] dump_stack+0x8/0x34
[<ffffffff81133d00>] warn_slowpath_common+0x78/0xa8
[<ffffffff81187e44>] irq_domain_associate_many+0x23c/0x260
[<ffffffff81187f38>] irq_create_mapping+0xd0/0x220
[<ffffffff81188104>] irq_create_of_mapping+0x7c/0x158
[<ffffffff813e5f08>] irq_of_parse_and_map+0x28/0x40
.
.
.
Both the CIU and GPIO interrupt domains were somewhat screwed up.
For the CIU domain, we need to call irq_domain_associate() for each of
the preassigned irq numbers. For the GPIO domain, we were applying
the register bit offset in octeon_irq_gpio_xlat, but it should be done
in octeon_irq_gpio_map instead.
Also: Reserve all 8 'core' irqs for the 'core' irq_chip so that they
don't get used by the other domains. Remove unused OCTEON_IRQ_*
symbols.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4190/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The ldb_di[01]_podf is implemented as a clk-divider that
divides by 1 or 2. In reality, the ldb_di[01]_ipu_div
dividers divide by either 3.5 or 7. Adding a fixed factor
of 1/3.5 fixes their children's clock rates.
This should probably be converted to rate table based dividers,
once available.
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
There is no specific atomic64 support code for any m68k CPUs, so we should
select CONFIG_GENERIC_ATOMC64 for all. Remove the existing per CPU selection
of this and select it for all m68k.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The ColdFire CPU sub-arch has kernel clk code support, so select
CONFIG_HAVE_CLK.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fix from Konrad Rzeszutek Wilk:
"Way back in v3.5 we added a mechanism to populate back pages that were
released (they overlapped with MMIO regions), but neglected to reserve
the proper amount of virtual space for extend_brk to work properly.
Coincidentally some other commit aligned the _brk space to larger area
so I didn't trigger this until it was run on a machine with more than
2GB of MMIO space."
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
|
|
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: intc: Handle domain association for sparseirq pre-allocated vectors.
sh: sh7269: Fix LCD pinmux
sh: dma: fix request_irq usage
|
|
This reverts commit 00e37bdb0113a98408de42db85be002f21dbffd3.
During shutdown of PVHVM guests with more than 2VCPUs on certain
machines we can hit the race where the replaced shared_info is not
replaced fast enough and the PV time clock retries reading the same
area over and over without any any success and is stuck in an
infinite loop.
Acked-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Put the parameters the right way around
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=44031
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
When we map a page that wasn't icache cleared before, do so when first
mapping it in KVM using the same information bits as the Linux mapping
logic. That way we are 100% sure that any page we map does not have stale
entries in the icache.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
In handling the H_CEDE hypercall, if this vcpu has already been
prodded (with the H_PROD hypercall, which Linux guests don't in fact
use), we branch to a numeric label '1f'. Unfortunately there is
another '1:' label before the one that we want to jump to. This fixes
the problem by using a textual label, 'kvm_cede_prodded'. It also
changes the label for another longish branch from '2:' to
'kvm_cede_exit' to avoid a possible future problem if code modifications
add another numeric '2:' label in between.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
* 'fixes' of git://github.com/hzhuang1/linux:
ARM: mmp: fix potential NULL dereference
|
|
Pull two sparc fixes from David S. Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Be less verbose during vmemmap population.
sparc64: do not clobber personality flags in sys_sparc64_personality()
|
|
The generic atomic64 support came in 2009 to support the perf subsystem
with the expectation that all architectures would implement atomic64
support. Since then, other optional parts of the generic kernel have
also come to expect atomic64 support. This patch enables generic atomic64
support for C6X architecture.
Signed-off-by: Mark Salter <msalter@redhat.com>
|
|
C6X currently lacks Lx_CACHE_SHIFT defines which are needed in a
few places in the generic kernel. This patch adds _SHIFT defines
for the various caches and bases the Lx_CACHE_BYTES defines on
them.
Signed-off-by: Mark Salter <msalter@redhat.com>
|
|
into fixes
From Jason Cooper <jason@lakedaemon.net>:
Small fixes for the orion platforms including kirkwood.
* 'fixes-for-v3.6' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: fix Makefile.boot
ARM: Kirkwood: Fix iconnect leds
ARM: Orion: Set eth packet size csum offload limit
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
While building the dtbs target, one is getting:
make dtbs
make[1]: *** No rule to make target `arch/arm/boot/kirkwood-qnap-ts219.dtb', needed by `arch/arm/boot/dtbs'. Stop.
make: *** [dtbs] Error 2
The reason is that there's no kirkwood-qnap-ts219.dts file. Update Makefile.boot
to reflect the dts files present.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
While converting, a led has been missed leading to wrong power blue led
definition. Add it back and fix the gpio used on the power blue led.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The mv643xx ethernet controller limits the packet size for the TX
checksum offloading. This patch sets this limits for Kirkwood and
Dove which have smaller limits that the default.
As a side note, this patch is an updated version of a patch sent some years
ago: http://lists.infradead.org/pipermail/linux-arm-kernel/2010-June/017320.html
which seems to have been lost.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Cc: <stable@vger.kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes for issues noted during the merge window, mostly
PM related.
* tag 'omap-fixes-for-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: dmtimers: Fix locking issue in omap_dm_timer_request*()
ARM: OMAP4: Register the OPP table only for 4430 device
cpufreq: OMAP: Handle missing frequency table on SMP systems
ARM: OMAP4: sleep: Save the complete used register stack frame
ARM: OMAP2+: cpu: Add am33xx device under cpu_class_is_omap2
omap: Fix multi.h when only ARCH_OMAP3 and SOC_AM33XX are selected
ARM: OMAP2+: Fix dmtimer set source clock failure
Revert "ARM: OMAP3: PM: call pre/post transition per powerdomain"
ARM: OMAP3: TWL4030: ensure sys_nirq1 is mux'd and wakeup enabled
omap2: mux: remove comment for nonexistent member
OMAP: remove unused parameter arch_id from uncompress.h
arm/dts: Mark vcxio, v2v1 and v1v8 regulators as always on
OMAP2+: Fix random config build break with !ARM_CPU_SUSPEND
arm/dts: Fix am33xx wdt node
ARM: OMAP3: igep0020: set GPIO mode for mux mcspi1_cs2 pin
Revert "ARM: OMAP3530evm: set pendown_state and debounce time for ads7846"
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Seems that Thomas' and my patches collided during the last merge
window.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.
This mimicks Yinghai Lu's x86 commit c2b91e2eec9678dbda274e906cc32ea8f711da3b
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.
This decreases the output by an order of 16.
Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit bacef661acdb634170a8faddbc1cf28e8f8b9eee.
This commit has been found to cause serious regressions on a number of
ASUS machines at the least. We probably need to provide a 1:1 map in
addition to the EFI virtual memory map in order for this to work.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reported-and-bisected-by: Jérôme Carretero <cJ-ko@zougloub.eu>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120805172903.5f8bb24c@zougloub.eu
|
|
Recent commit 332afa656e76458ee9cf0f0d123016a0658539e4 cleaned up
a workaround that updates irq_cfg domain for legacy irq's that
are handled by the IO-APIC. This was assuming that the recent
changes in assign_irq_vector() were sufficient to remove the workaround.
But this broke couple of AMD platforms. One of them seems to be
sending interrupts to the offline cpu's, resulting in spurious
"No irq handler for vector xx (irq -1)" messages when those cpu's come online.
And the other platform seems to always send the interrupt to the last logical
CPU (cpu-7). Recent changes had an unintended side effect of using only logical
cpu-0 in the IO-APIC RTE (during boot for the legacy interrupts) and this
broke the legacy interrupts not getting routed to the cpu-7 on the AMD
platform, resulting in a boot hang.
For now, reintroduce the removed workaround, (essentially not allowing the
vector to change for legacy irq's when io-apic starts to handle the irq. Which
also addressed the uninteded sife effect of just specifying cpu-0 in the
IO-APIC RTE for those irq's during boot).
Reported-and-tested-by: Robert Richter <robert.richter@amd.com>
Reported-and-tested-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1344453412.29170.5.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
|
|
Patch b6d1c33a31 "ARM: Orion: Consolidate the address map setup" tried
to merge the address map for the four orion platforms, but apparently
got it wrong for mv78xx0. Admittedly I don't understand what this
code actually does, but it's clear that the current version is
wrong.
Without this patch, building mv78xx0_defconfig results in:
arch/arm/mach-mv78xx0/addr-map.c:59:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-mv78xx0/addr-map.c:59:2: warning: (near initialization for 'addr_map_cfg.win_cfg_base') [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Michael Walle <michael@walle.cc>
Cc: Nicolas Pitre <nico@linaro.org>
|
|
If PMU counter has PEBS enabled it is not enough to disable counter
on a guest entry since PEBS memory write can overshoot guest entry
and corrupt guest memory. Disabling PEBS during guest entry solves
the problem.
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120809085234.GI3341@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
