| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (113 commits)
omap4: Add support for i2c init
omap: Fix i2c platform init code for omap4
OMAP2 clock: fix recursive spinlock attempt when CONFIG_CPU_FREQ=y
OMAP powerdomain, hwmod, omap_device: add some credits
OMAP4 powerdomain: Support LOWPOWERSTATECHANGE for powerdomains
OMAP3 clock: add support for setting the divider for sys_clkout2 using clk_set_rate
OMAP4 powerdomain: Fix pwrsts flags for ALWAYS ON domains
OMAP: timers: Fix clock source names for OMAP4
OMAP4 clock: Support clk_set_parent
OMAP4: PRCM: Add offset defines for all CM registers
OMAP4: PRCM: Add offset defines for all PRM registers
OMAP4: PRCM: Remove duplicate definition of base addresses
OMAP4: PRM: Remove MPU internal code name and apply PRCM naming convention
OMAP4: CM: Remove non-functional registers in ES1.0
OMAP: hwmod: Replace WARN by pr_warning for clockdomain check
OMAP: hwmod: Rename hwmod name for the MPU
OMAP: hwmod: Do not exit the iteration if one clock init failed
OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
OMAP: hwmod: Remove IS_ERR check with omap_clk_get_by_name return value
OMAP: hwmod: Fix wrong pointer iteration in oh->slaves
...
|
|
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
USB: remove unused usb_buffer_alloc and usb_buffer_free macros
usb: musb: update gfp/slab.h includes
USB: ftdi_sio: fix legacy SIO-device header
USB: kl5usb105: reimplement using generic framework
USB: kl5usb105: minor clean ups
USB: kl5usb105: fix memory leak
USB: io_ti: use kfifo to implement write buffering
USB: io_ti: remove unsused private counter
USB: ti_usb: use kfifo to implement write buffering
USB: ir-usb: fix incorrect write-buffer length
USB: aircable: fix incorrect write-buffer length
USB: safe_serial: straighten out read processing
USB: safe_serial: reimplement read using generic framework
USB: safe_serial: reimplement write using generic framework
usb-storage: always print quirks
USB: usb-storage: trivial debug improvements
USB: oti6858: use port write fifo
USB: oti6858: use kfifo to implement write buffering
USB: cypress_m8: use kfifo to implement write buffering
USB: cypress_m8: remove unused drain define
...
Fix up conflicts (due to usb_buffer_alloc/free renaming) in
drivers/input/tablet/acecad.c
drivers/input/tablet/kbtab.c
drivers/input/tablet/wacom_sys.c
drivers/media/video/gspca/gspca.c
sound/usb/usbaudio.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
|
|
Add platform init code for the OMAP3 OHCI driver.
Also, configure padconf settings for OMAP3 depending
on which port mode is used.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
EXTVBUS programming is required by OMAP3EVM REV >=E to supply 500mA
power so adding a flag which can be used by musb driver to program
EXTVBUS.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
Add support for i2c init for omap4.
This patch is based on and earlier patch by
Santosh Shilimkar <santosh.shilimkar@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add separate omap_i2c_add_bus functions for mach-omap1
and mach-omap2. Make the mach-omap2 init set the interrupt
dynamically to support.
This is needed to add support for omap4 in a way that
works with multi-omap builds. This will eventually get
fixed in a generic way with the omap hwmods.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
The OMAP2 MPU virtual clock node code attempted to call clk_get_rate()
while the clockfw_lock spinlock was held. Fix by reading the sys_ck
rate directly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add some missing credits for people who have contributed significant features
or fixes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Thara Gopinath <thara@ti.com>
|
|
Some powerdomains in OMAP4 support a direct transition from one sleep
state to another deeper sleep state without having to wakeup the
powerdomain. This patch adds an api in the powerdomain framework to
set the LOWPOWERSTATECHANGE bit in PWRSTCTRL register.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
clk_set_rate
Add clock framework support for changing the rate of sys_clkout2.
Signed-off-by: Laine Walker-Avina <lwalkera@ieee.org>
[paul@pwsan.com: added commit message, added .round_rate pointer]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The pwrsts flag for ALWAYS ON domains like always_on_core_pwrdm
and wkup_pwrdm is wrongly populated with the define for a
powerdomain power state, instead of the allowable state
bitfields.
This causes a few api's to fail sensing invalid pwrst
requested.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The clock sources for timers on OMAP4 (system clock and 32k
clock) have their names wronly populated.
This patch fixes them so the omap_dm_timer_set_source
does not fail anymore.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Remove the hack put in place while clock framework was still not in
place for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The cm44xx.h files only had absolute register address
defines for all CM registers.
This patch adds additional register offset defines for all the
registers, so they can be used with apis like cm_read_mod_*
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The prm44xx.h files only had absolute register address
defines for all PRM registers.
This patch adds additional register offset defines for all the
registers, so they can be used with apis like prm_read_mod_*
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
CM1, CM2, PRM, SCRM and MPU_PRCM are already defined in omap44xx.h
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
|
|
The MPU subsystem was named based on internal code name (CHIRON).
This patch will remove all the occurences of the chiron name
are replace it with PRCM_MPU in order to differentiate
the MPU local PRCM to the global one.
Remove PDA_ from PRCM_MPU registers names to stick to the global
PRM naming convention.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
|
|
The automatic HW restore from OFF mode is not functional at all in
OMAP4430 ES1.0.
Because of that, it will be extensively changed in the next Si revision,
and the compatibilty will not be maintained with ES1.0.
Remove the current XXX_RESTORE registers definition to avoid future
conflicts with the next Si revision.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
|
|
Most of the clock nodes belong to a clock domain, but it is perfectly valid
to have clock without clock domain.
Root clocks for example does not belong to any clock domain.
Keep the warning but reduce the verbosity.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
In the lastest OMAP4 hwmod data file, the _hwmod was removed
in order to save some memory space and because it does not
bring a lot.
The same cleanup will be have to done for other hwmods in
OMAP2 & 3 data files.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
|
|
During the _init_clocks phase, the iteration is stopped but the
status is still change from _HWMOD_STATE_REGISTERED to
_HWMOD_STATE_CLKS_INITED.
Since the _setup phase will be done nevertheless, it might be
better to keep initializing the others clocks nodes and just
keep the warning.
It is much easier to debug when a important number of clocks
name are wrong during the early debug phase of a new platform.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The WARN is a little bit too verbose and is not providing
usefull information in that case.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The previous clock API was returning a standard linux error code in
case of failure. This is not the case anymore with the new
omap_clk_get_by_name API. A NULL value means that the clock node
does not exist.
Replace all the IS_ERR check by a !clk check.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The iteration is currently done on the omap_hwmod_ocp_if pointer
and not on the table pointer that reference them.
It worked most of the time because the structure are contiguous in
memory.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Some initiator modules in OMAP2 & 3 does not have IDLEST bit,
in that case we cannot detect the module readiness by
polling that bit and must exist the function immediately
assuming that the module is ready.
The previous flag was affected to the OCP interface. While it is
technically true that the idlest is related to the L4 slave
interface of the module, the PRCM status belong to the module.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The return of the omap4_cm_wait_module_ready function is checked
in order to avoid accessing the sysconfig register if the module is
not in the correct state.
In that case the _setup will exit without trying to reset
using sysconfig.
For the moment a warning is printed. A proper management of fclk
and module reset will have to be done in order to init correctly
the problematic IPs listed below.
<4>omap_hwmod: ivahd: cannot be enabled (3)
<4>omap_hwmod: iss: cannot be enabled (3)
<4>omap_hwmod: tesla: cannot be enabled (3)
<4>omap_hwmod: sdma: cannot be enabled (3)
<4>omap_hwmod: sl2: cannot be enabled (3)
<4>omap_hwmod: sad2d: cannot be enabled (3)
<4>omap_hwmod: ducati: cannot be enabled (3)
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The maximum timeout to wait for the PRCM to request that a module
exit idle or reach functionnal state is common to OMAP2/3/4 SoCs,
so, move it to the chip family-common cm.h include file.
Reduce the timeout from 20 ms to 2 ms.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Accessing the clkctrl register using offset of module & device is hard
to do in OMAP4 due to the way the CM1, CM2, PRM and PRCM_MPU are located
in the address space. There is no common base address anymore for all the
CM registers.
The easiest way to handle that on OMAP4 is to provide the absolute address
of the XXX_CLKCTRL register per hwmod.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
|
|
Clean up comment style, remove unnecessary includes, and resolve some
checkpatch warnings in plat-omap/clock.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit 678bc9a2eabb7f444ef8ad1cfc5ef394e2bd8bf2 split dpll4_m2_ck,
creating a 34xx and a 36xx variant, to handle the additional 16
divider steps provided on the 36xx. This in turn required dynamic
rewriting of the clock tree during initialization, which is
undesirable. All this seems to be unnecessary, though, since the
additional 16 divider steps can simply be marked with RATE_IN_36XX.
This patch does so and re-merges the affected structures.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vishwanath Sripathy <vishwanath.bs@ti.com>
|
|
Rename the RATE_IN_343X clksel_rate.rate flag to be RATE_IN_3XXX, to reflect
that these rates are valid on all OMAP3 platforms, not just 343X.
Also rename the RATE_IN_OMAP3430ES2 clksel_rate.rate flag to be
RATE_IN_OMAP3430ES2PLUS, to reflect that these flags are valid on all
OMAP3 platforms after 3430ES2.
This patch should not result in any functional changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
|
|
This patch cleans up arch/arm/mach-omap2/clkt_clksel.c. It:
- makes several functions static that are not called outside the file;
- adds documentation;
- makes some code paths easier to read (hopefully), by breaking up
compound statements and removing redundant checks;
- converts some pr_err()s that indicate clock tree data problems into WARN()s,
so they are more likely to be noticed;
- and moves omap2_clk_round_rate() back into mach-omap2/clock.c, its proper
home, since it is not clksel-specific.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The DEFAULT_RATE clksel_rate flag is essentially useless. It was set
on some of the lowest divisors, which, when switching to a much
higher-rate parent, could have potentially resulted in rates that
exceeded the hardware specifications for downstream clocks in the
window between the clk_set_parent(), and a subsequent clk_set_rate().
It seems much safer to just remove the flag and always use the highest
available divisor (resulting in the lowest possible rate) after the
switch, and this patch does so.
Ideally, it would be best to first attempt to switch to a divisor that
matches the clock's rate with the previous parent, if at all possible.
But that is a project for some other day or some other person. The
parent changing code is rarely used.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Writes to the PM_*GRPSEL registers should use _GRPSEL_ macros, not _EN_ macros,
to match the TRM and guard against inadvertent error. This patch should
not cause any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
|
|
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them. This makes the use of these
macros consistent. It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Fix all of the remaining OMAP2 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
remove the section annotation from omap1_clk_disable_unused()
to kill the section mismatch warning.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add stalker board to omap3_defconfig
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
- Update the omap3_defconfig to sync up with the generated .config
- Increase CONFIG_LOG_BUF_SHIFT to 16 to allow the entire
boot log to be captured
(useful when using boot time tracer, for example)
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add OMAP3 Stalker board LK-S defconfig.
Signed-off-by: Jason Lam <lzg@ema-tech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for OMAP3Stalker boards
Signed-off-by: Jason Lam <lzg@ema-tech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enables HSMMC support for OMAP4430 defconfig
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In OMAP4, MMC1 PBIAS and its associated IO is software-controlled
by CONTROL_PBIAS and CONTROL_MMC1 registers. This patch adds PBIAS
configuration for MMC1 Controller during power-ON and power-OFF
of regulator.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Adding support for MMC1 & MMC2 controllers of OMAP4430 SDP
to board file.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
