| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit d00a9dd21bdf7908b70866794c8313ee8a5abd5c ]
Several problems fixed in this patch :
1) Target of the conditional jump in case a divide by 0 is performed
by a bpf is wrong.
2) Must 'generate' the full function prologue/epilogue at pass=0,
or else we can stop too early in pass=1 if the proglen doesnt change.
(if the increase of prologue/epilogue equals decrease of all
instructions length because some jumps are converted to near jumps)
3) Change the wrong length detection at the end of code generation to
issue a more explicit message, no need for a full stack trace.
Reported-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a7546b377bdaa25ac77f33d9433c59f259b9688 upstream.
If NR_CPUS < 256 then arch_spinlock_t is only 16 bits wide but struct
xen_spinlock is 32 bits. When a spin lock is contended and
xl->spinners is modified the two bytes immediately after the spin lock
would be corrupted.
This is a regression caused by 84eb950db13ca40a0572ce9957e14723500943d6
(x86, ticketlock: Clean up types and accessors) which reduced the size
of arch_spinlock_t.
Fix this by making xl->spinners a u8 if NR_CPUS < 256. A
BUILD_BUG_ON() is also added to check the sizes of the two structures
are compatible.
In many cases this was not noticable as there would often be padding
bytes after the lock (e.g., if any of CONFIG_GENERIC_LOCKBREAK,
CONFIG_DEBUG_SPINLOCK, or CONFIG_DEBUG_LOCK_ALLOC were enabled).
The bnx2 driver is affected. In struct bnx2, phy_lock and
indirect_lock may have no padding after them. Contention on phy_lock
would corrupt indirect_lock making it appear locked and the driver
would deadlock.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 612539e81f655f6ac73c7af1da8701c1ee618aee upstream.
On v7, we use the same cache maintenance instructions for data lines
as for unified lines. This was not the case for v6, where HARVARD_CACHE
was defined to indicate the L1 cache topology.
This patch removes the erroneous compile-time check for HARVARD_CACHE in
proc-v7.S, ensuring that we perform I-side invalidation at boot.
Reported-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Catalin Marinas <Catalin.Marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d65015f7c5c5be9fd3f5e567889c844ba81bdc9c upstream.
This applies ARM errata 764369 for all ux500 platforms.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e90772f76010c315474bde59eaca7cc4c94d645 upstream.
Currently setting it to PQFP changes subtype to BGA as subtypes are
swapped in at91rm9200_set_type().
Wrong subtype causes GPIO bank D not to work at all.
After this fix, subtype is still set as unknown. But board code should
fill it in with proper value. Another information is thus printed.
Bug discovery and first implementation made by Veli-Pekka Peltola.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a3535069e33d8b416f406c159ce924427315303 upstream.
Passing the address of a variable as an operand to an asm statement
doesn't mark the value of this variable as used, so gcc may optimize its
initialisation away. Fix this by using the "m" constraint instead.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5b68edc91cdc972c46f76f85eded7ffddc3ff5c2 upstream.
We've decided to provide CPU family specific container files
(starting with CPU family 15h). E.g. for family 15h we have to
load microcode_amd_fam15h.bin instead of microcode_amd.bin
Rationale is that starting with family 15h patch size is larger
than 2KB which was hard coded as maximum patch size in various
microcode loaders (not just Linux).
Container files which include patches larger than 2KB cause
different kinds of trouble with such old patch loaders. Thus we
have to ensure that the default container file provides only
patches with size less than 2KB.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20120120164412.GD24508@alberich.amd.com
[ documented the naming convention and tidied the code a bit. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a51467b146ab7948d2f6812892eac120a30529c upstream.
uv_gpa_to_soc_phys_ram() was inadvertently ignoring the
shift values. This fix takes the shift into account.
Signed-off-by: Russ Anderson <rja@sgi.com>
Link: http://lkml.kernel.org/r/20120119020753.GA7228@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2ebc71d472020bc30e29afe8c4d2a85a5b41f56 upstream.
Initialize two spinlocks in tlb_uv.c and also properly define/initialize
the uv_irq_lock.
The lack of explicit initialization seems to be functionally
harmless, but it is diagnosed when these are turned on:
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_LOCKDEP=y
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/E1RnXd1-0003wU-PM@eag09.americas.sgi.com
[ Added the uv_irq_lock initialization fix by Dimitri Sivanich ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c25a785d6647984505fa165b5cd84cfc9a95970b upstream.
If the provided system call number is equal to __NR_syscalls, the
current check will pass and a function pointer just after the system
call table may be called, since sys_call_table is an array with total
size __NR_syscalls.
Whether or not this is a security bug depends on what the compiler puts
immediately after the system call table. It's likely that this won't do
anything bad because there is an additional NULL check on the syscall
entry, but if there happens to be a non-NULL value immediately after the
system call table, this may result in local privilege escalation.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Eugene Teo <eugeneteo@kernel.sg>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c5d35d399e685acccc85a675e8765c26b2a9813a upstream.
This patch implements a workaround for a UV2 hardware bug.
The bug is a non-atomic update of a memory-mapped register. When
hardware message delivery and software message acknowledge occur
simultaneously the pending message acknowledge for the arriving
message may be lost. This causes the sender's message status to
stay busy.
Part of the workaround is to not acknowledge a completed message
until it is verified that no other message is actually using the
resource that is mistakenly recorded in the completed message.
Part of the workaround is to test for long elapsed time in such
a busy condition, then handle it by using a spare sending
descriptor. The stay-busy condition is eventually timed out by
hardware, and then the original sending descriptor can be
re-used. Most of that logic change is in keeping track of the
current descriptor and the state of the spares.
The occurrences of the workaround are added to the BAU
statistics.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116211947.GC5767@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d059f9fa84a30e04279c6ff615e9e2cf3b260191 upstream.
Move the call to enable_timeouts() forward so that
BAU_MISC_CONTROL is initialized before using it in
calculate_destination_timeout().
Fix the calculation of a BAU destination timeout
for UV2 (in calculate_destination_timeout()).
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116211848.GB5767@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit da87c937e5a2374686edd58df06cfd5050b125fa upstream.
Update the use of the Broadcast Assist Unit on SGI Altix UV2 to
the use of native UV2 mode on new hardware (not the legacy mode).
UV2 native mode has a different format for a broadcast message.
We also need quick differentiaton between UV1 and UV2.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116211750.GA5767@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9f10f6a520deb3639fac78d81151a3ade88b4e7f upstream.
In SRAT v1, we had 8bit proximity domain (PXM) fields; SRAT v2 provides
32bits for these. The new fields were reserved before.
According to the ACPI spec, the OS must disregrard reserved fields.
ia64 did handle the PXM fields almost consistently, but depending on
sgi's sn2 platform. This patch leaves the sn2 logic in, but does also
use 16/32 bits for PXM if the SRAT has rev 2 or higher.
The patch also adds __init to the two pxm accessor functions, as they
access __initdata now and are called from an __init function only anyway.
Note that the code only uses 16 bits for the PXM field in the processor
proximity field; the patch does not address this as 16 bits are more than
enough.
Signed-off-by: Kurt Garloff <kurt@garloff.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cd298f60a2451a16e0f077404bf69b62ec868733 upstream.
In SRAT v1, we had 8bit proximity domain (PXM) fields; SRAT v2 provides
32bits for these. The new fields were reserved before.
According to the ACPI spec, the OS must disregrard reserved fields.
x86/x86-64 was rather inconsistent prior to this patch; it used 8 bits
for the pxm field in cpu_affinity, but 32 bits in mem_affinity.
This patch makes it consistent: Either use 8 bits consistently (SRAT
rev 1 or lower) or 32 bits (SRAT rev 2 or higher).
cc: x86@kernel.org
Signed-off-by: Kurt Garloff <kurt@garloff.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit da517a08ac5913cd80ce3507cddd00f2a091b13c upstream.
SGI UV systems print a message during boot:
UV: Found <num> blades
Due to packaging changes, the blade count is not accurate for
on the next generation of the platform. This patch corrects the
count.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20120106191900.GA19772@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9af0c7a6fa860698d080481f24a342ba74b68982 upstream.
On x86_32 casting the unsigned int result of get_random_int() to
long may result in a negative value. On x86_32 the range of
mmap_rnd() therefore was -255 to 255. The 32bit mode on x86_64
used 0 to 255 as intended.
The bug was introduced by 675a081 ("x86: unify mmap_{32|64}.c")
in January 2008.
Signed-off-by: Ludwig Nussel <ludwig.nussel@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: harvey.harrison@gmail.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/201111152246.pAFMklOB028527@wpaz5.hot.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5cf9a4e69c1ff0ccdd1d2b7404f95c0531355274 upstream.
We only need amd_bus.o for AMD systems with PCI. arch/x86/pci/Makefile
already depends on CONFIG_PCI=y, so this patch just adds the dependency
on CONFIG_AMD_NB.
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 24d25dbfa63c376323096660bfa9ad45a08870ce upstream.
This factors out the AMD native MMCONFIG discovery so we can use it
outside amd_bus.c.
amd_bus.c reads AMD MSRs so it can remove the MMCONFIG area from the
PCI resources. We may also need the MMCONFIG information to work
around BIOS defects in the ACPI MCFG table.
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ae5cd86455381282ece162966183d3f208c6fad7 upstream.
This assures that a _CRS reserved host bridge window or window region is
not used if it is not addressable by the CPU. The new code either trims
the window to exclude the non-addressable portion or totally ignores the
window if the entire window is non-addressable.
The current code has been shown to be problematic with 32-bit non-PAE
kernels on systems where _CRS reserves resources above 4GB.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Renninger <trenn@novell.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e4f387d8db3ba3c2dae4d8bdfe7bb5f4fe1bcb0d upstream.
Unpaired calling of probe_hcall_entry and probe_hcall_exit might happen
as following, which could cause incorrect preempt count.
__trace_hcall_entry => trace_hcall_entry -> probe_hcall_entry =>
get_cpu_var => preempt_disable
__trace_hcall_exit => trace_hcall_exit -> probe_hcall_exit =>
put_cpu_var => preempt_enable
where:
A => B and A -> B means A calls B, but
=> means A will call B through function name, and B will definitely be
called.
-> means A will call B through function pointer, so B might not be
called if the function pointer is not set.
So error happens when only one of probe_hcall_entry and probe_hcall_exit
get called during a hcall.
This patch tries to move the preempt count operations from
probe_hcall_entry and probe_hcall_exit to its callers.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 37fb9a0231ee43d42d069863bdfd567fca2b61af upstream.
When re-enabling interrupts we have code to handle edge sensitive
decrementers by resetting the decrementer to 1 whenever it is negative.
If interrupts were disabled long enough that the decrementer wrapped to
positive we do nothing. This means interrupts can be delayed for a long
time until it finally goes negative again.
While we hope interrupts are never be disabled long enough for the
decrementer to go positive, we have a very good test team that can
drive any kernel into the ground. The softlockup data we get back
from these fails could be seconds in the future, completely missing
the cause of the lockup.
We already keep track of the timebase of the next event so use that
to work out if we should trigger a decrementer exception.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7237/1: PL330: Fix driver freeze
ARM: 7197/1: errata: Remove SMP dependency for erratum 751472
ARM: 7196/1: errata: Remove SMP dependency for erratum 720789
ARM: 7220/1: mmc: mmci: Fixup error handling for dma
ARM: 7214/1: mmc: mmci: Fixup handling of MCI_STARTBITERR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: plat-orion: make gpiochip label unique
enable uncompress log on cpuimx35sd
cpuimx35: fix touchscreen support
cpuimx35sd: fix Kconfig
clock-imx35: fix reboot in internal boot mode
dma: MX3_IPU fix depends
imx_v4_v5_defconfig: update default configuration
cpuimx25sd: fix Kconfig
arm/imx: fix cpufreq section mismatch
ARM:imx:fix pwm period value
ARM: OMAP: hwmod data: fix iva and mailbox hwmods for OMAP 3
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 'v3.2-samsung-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Remove duplicated SROMC static memory mapping
ARM: SAMSUNG: Fix build error when selecting CPU_FREQ_S3C24XX_DEBUGFS on S3C2440
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix raw_spin_unlock_irqrestore() usage
oprofile, arm/sh: Fix oprofile_arch_exit() linkage issue
|
|
Commit 2a95ea6c0d129b4 ("procfs: do not overflow get_{idle,iowait}_time
for nohz") did not take into account that one some architectures jiffies
and cputime use different units.
This causes get_idle_time() to return numbers in the wrong units, making
the idle time fields in /proc/stat wrong.
Instead of converting the usec value returned by
get_cpu_{idle,iowait}_time_us to units of jiffies, use the new function
usecs_to_cputime64 to convert it to the correct unit of cputime64_t.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Artem S. Tashkinov" <t.artem@mailcity.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
SROMC static memory mapping is included in the common s5p initialization
code. Hence, remove the duplicated SROMC static memory mapping for EXYNOS.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Cc: stable@kernel.org
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Following is happened when CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
is selected without building of s3c2410-iotiming.c file:
arch/arm/mach-s3c2440/built-in.o:(.data+0x38c): undefined reference to `s3c2410_iotiming_debugfs
Basically, the CONFIG_S3C2410_IOTIMING is not selected for
MACH_MINI2440. Because the s3c2410-iotiming.c is not ever
compiled and enabling CONFIG_CPU_FREQ_S3C24XX_DEBUGFS option
caused undefined reference to s3c2410_iotiming_debugfs()
defined in that file. The s3c2410_iotiming_debugfs defined
as NULL for this case.
Signed-off-by: Denis Kuzmenko <linux@solonet.org.ua>
Cc: stable@kernel.org
[kgene.kim@samsung.com: removed useless changes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This is required for THIS_MODULE. We recently stopped acquiring
it via some other header.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Currently kvmppc_start_thread() tries to wake other SMT threads via
xics_wake_cpu(). Unfortunately xics_wake_cpu only exists when
CONFIG_SMP=Y so when compiling with CONFIG_SMP=N we get:
arch/powerpc/kvm/built-in.o: In function `.kvmppc_start_thread':
book3s_hv.c:(.text+0xa1e0): undefined reference to `.xics_wake_cpu'
The following should be fine since kvmppc_start_thread() shouldn't
called to start non-zero threads when SMP=N since threads_per_core=1.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
kvmppc_h_pr is only available if CONFIG_KVM_BOOK3S_64_PR.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
compute_tlbie_rb is only used on ppc64 and cannot be compiled on ppc32.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Unlike all of the other cpuid bits, the TSC deadline timer bit is set
unconditionally, regardless of what userspace wants.
This is broken in several ways:
- if userspace doesn't use KVM_CREATE_IRQCHIP, and doesn't emulate the TSC
deadline timer feature, a guest that uses the feature will break
- live migration to older host kernels that don't support the TSC deadline
timer will cause the feature to be pulled from under the guest's feet;
breaking it
- guests that are broken wrt the feature will fail.
Fix by not enabling the feature automatically; instead report it to userspace.
Because the feature depends on KVM_CREATE_IRQCHIP, which we cannot guarantee
will be called, we expose it via a KVM_CAP_TSC_DEADLINE_TIMER and not
KVM_GET_SUPPORTED_CPUID.
Fixes the Illumos guest kernel, which uses the TSC deadline timer feature.
[avi: add the KVM_CAP + documentation]
Reported-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Tested-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
User space may create the PIT and forgets about setting up the irqchips.
In that case, firing PIT IRQs will crash the host:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000128
IP: [<ffffffffa10f6280>] kvm_set_irq+0x30/0x170 [kvm]
...
Call Trace:
[<ffffffffa11228c1>] pit_do_work+0x51/0xd0 [kvm]
[<ffffffff81071431>] process_one_work+0x111/0x4d0
[<ffffffff81071bb2>] worker_thread+0x152/0x340
[<ffffffff81075c8e>] kthread+0x7e/0x90
[<ffffffff815a4474>] kernel_thread_helper+0x4/0x10
Prevent this by checking the irqchip mode before starting a timer. We
can't deny creating the PIT if the irqchips aren't set up yet as
current user land expects this order to work.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Add a req_running field to the pl330_thread to track which request (if
any) has been submitted to the DMA. This mechanism replaces the old
one in which we tried to guess the same by looking at the PC of the
DMA, which could prevent the driver from sending more requests if it
didn't guess correctly.
Reference: <1323631637-9610-1-git-send-email-javi.merino@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Activation conditions for a workaround should not be encoded in the
workaround's direct dependencies if this makes otherwise reasonable
configuration choices impossible.
This patches uses the SMP/UP patching facilities instead to compile
out the workaround if the configuration means that it is definitely
not needed.
This means that configs for buggy silicon can simply select
ARM_ERRATA_751472, without preventing a UP kernel from being built
or duplicatiing knowledge about when to activate the workaround.
This seems the correct way to do things, because the erratum is a
property of the silicon, irrespective of what the kernel config
happens to be.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Activation conditions for a workaround should not be encoded in the
workaround's direct dependencies if this makes otherwise reasonable
configuration choices impossible.
The workaround for erratum 720789 only affects a code path which is
not active in UP kernels; hence it should be safe to turn on in UP
kernels, without penalty.
This patch simply removes the extra dependency on SMP from Kconfig.
This means that configs for buggy silicon can simply select
ARM_ERRATA_720789, without preventing a UP kernel from being built
or duplicatiing knowledge about when to activate the workaround.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use raw_spin_unlock_irqrestore() as equivalent to
raw_spin_lock_irqsave().
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1324646665-13334-1-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This change fixes a linking problem, which happens if oprofile
is selected to be compiled as built-in:
`oprofile_arch_exit' referenced in section `.init.text' of
arch/arm/oprofile/built-in.o: defined in discarded section
`.exit.text' of arch/arm/oprofile/built-in.o
The problem is appeared after commit 87121ca504, which
introduced oprofile_arch_exit() calls from __init function. Note
that the aforementioned commit has been backported to stable
branches, and the problem is known to be reproduced at least
with 3.0.13 and 3.1.5 kernels.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: oprofile-list <oprofile-list@lists.sourceforge.net>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20111222151540.GB16765@erda.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This silently was working for many years and stopped working on
Niagara-T3 machines.
We need to set the MSIQ to VALID before we can set it's state to IDLE.
On Niagara-T3, setting the state to IDLE first was causing HV_EINVAL
errors. The hypervisor documentation says, rather ambiguously, that
the MSIQ must be "initialized" before one can set the state.
I previously understood this to mean merely that a successful setconf()
operation has been performed on the MSIQ, which we have done at this
point. But it seems to also mean that it has been set VALID too.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Add a flow_cache_flush_deferred function
ipv4: reintroduce route cache garbage collector
net: have ipconfig not wait if no dev is available
sctp: Do not account for sizeof(struct sk_buff) in estimated rwnd
asix: new device id
davinci-cpdma: fix locking issue in cpdma_chan_stop
sctp: fix incorrect overflow check on autoclose
r8169: fix Config2 MSIEnable bit setting.
llc: llc_cmsg_rcv was getting called after sk_eat_skb.
net: bpf_jit: fix an off-one bug in x86_64 cond jump target
iwlwifi: update SCD BC table for all SCD queues
Revert "Bluetooth: Revert: Fix L2CAP connection establishment"
Bluetooth: Clear RFCOMM session timer when disconnecting last channel
Bluetooth: Prevent uninitialized data access in L2CAP configuration
iwlwifi: allow to switch to HT40 if not associated
iwlwifi: tx_sync only on PAN context
mwifiex: avoid double list_del in command cancel path
ath9k: fix max phy rate at rate control init
nfc: signedness bug in __nci_request()
iwlwifi: do not set the sequence control bit is not needed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, dumpstack: Fix code bytes breakage due to missing KERN_CONT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
oprofile: Fix uninitialized memory access when writing to writing to oprofilefs
|
|
* 'sh-fixes-for-linus' of git://github.com/pmundt/linux-sh:
sh: fix build warning in board-sh7757lcr
|
|
* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
ARM: mach-shmobile: SH73A0 external Ethernet fix
ARM: mach-shmobile: AG5EVM GIC Sparse IRQ fix
ARM: mach-shmobile: Kota2 TPU LED platform data
ARM: mach-shmobile: Kota2 GIC Sparse IRQ fix
ARM: mach-shmobile: Kota2 PINT fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
|
|
The former implementation adds a fix gpiochip label string
to the framework. This is confusing because orion_gpio_init
is called more than once and this ends up in different gpiochips
with the same label.
This patch adds the already present orion_gpio_chip_count to the
label string to make it unique in the system.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When printing the code bytes in show_registers(), the markers around the
byte at the fault address could make the printk() format string look
like a valid log level and facility code. This would prevent this byte
from being printed and result in a spurious newline:
[ 7555.765589] Code: 8b 32 e9 94 00 00 00 81 7d 00 ff 00 00 00 0f 87 96 00 00 00 48 8b 83 c0 00 00 00 44 89 e2 44 89 e6 48 89 df 48 8b 80 d8 02 00 00
[ 7555.765683] 8b 48 28 48 89 d0 81 e2 ff 0f 00 00 48 c1 e8 0c 48 c1 e0 04
Add KERN_CONT where needed, and elsewhere in show_registers() for
consistency.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Link: http://lkml.kernel.org/r/4EEFA7AE.9020407@ladisch.de
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
x86 jump instruction size is 2 or 5 bytes (near/long jump), not 2 or 6
bytes.
In case a conditional jump is followed by a long jump, conditional jump
target is one byte past the start of target instruction.
Signed-off-by: Markus Kötter <nepenthesdev@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
