| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch provide migration to using "mtd-ram" driver instead of using
special driver for handling NVRAM memory.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We do not have driver for Up/Down digital potentiometer (DPOT), so
just define pins as GPIOs and export these pins to user.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This clock will be used in audio subsystem. Since audio cannot work
without PLL we should indicate this.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch removes dependency of NEED_MACH_MEMORY_H for CLPS711X-target.
Since some board may have memory holes, define ARCH_HAS_HOLES_MEMORYMODEL
for these boards.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
arch_initcall was been removed from GPIO driver, so this patch
re-add support for GPIO into boards as platform_device.
Since some drivers (spi, nand, etc.) is not support deferred probe,
separate machine init calls is used in board code to make proper
loading sequence.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This patcheset includes fixes for:
- the PCI/LBA which brings back the stifb graphics framebuffer
console
- possible memory overflows in parisc kernel init code
- parport support on older GSC machines
- avoids that users by mistake enable PARPORT_PC_SUPERIO on parisc
- MAINTAINERS file list updates for parisc."
* 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: parport0: fix this legacy no-device port driver!
parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
parisc/PCI: Set type for LBA bus_num resource
MAINTAINERS: update parisc architecture file list
parisc: kernel: using strlcpy() instead of strcpy()
parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
parisc: memory overflow, 'name' length is too short for using
|
|
'boot_args' is an input args, and 'boot_command_line' has a fix length.
So use strlcpy() instead of strcpy() to avoid memory overflow.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
There's a Makefile line setting cflags for CONFIG_PA7100. But that
Kconfig macro doesn't exist. There is a Kconfig symbol PA7000, which
covers both PA7000 and PA7100 processors. So let's use the corresponding
Kconfig macro.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
With CONFIG_DISCONTIGMEM=y and multiple physical memory areas,
cat /proc/kpageflags triggers this kernel bug:
kernel BUG at arch/parisc/include/asm/mmzone.h:50!
CPU: 2 PID: 7848 Comm: cat Tainted: G D W 3.10.0-rc3-64bit #44
IAOQ[0]: kpageflags_read0x128/0x238
IAOQ[1]: kpageflags_read0x12c/0x238
RP(r2): proc_reg_read0xbc/0x130
Backtrace:
[<00000000402ca2d4>] proc_reg_read0xbc/0x130
[<0000000040235bcc>] vfs_read0xc4/0x1d0
[<0000000040235f0c>] SyS_read0x94/0xf0
[<0000000040105fc0>] syscall_exit0x0/0x14
kpageflags_read() walks through the whole memory, even if some memory
areas are physically not available. So, we should better not BUG on an
unavailable pfn in pfn_to_nid() but just return the expected value -1 or
0.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
'path.bc[i]' can be asigned by PCI_SLOT() which can '> 10', so sizeof(6
* "%u:" + "%u" + '\0') may be 21.
Since 'name' length is 20, it may be memory overflow.
And 'path.bc[i]' is 'unsigned char' for printing, we can be sure the
max length of 'name' must be less than 28.
So simplify thinking, we can use 28 instead of 20 directly, and do not
think of whether 'patchc.bc[i]' can '> 100'.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few more fixes for powerpc 3.10. It's a bit more than I
would have liked this late in the game but I suppose that's what
happens with a brand new chip generation coming out.
A few regression fixes, some last minute fixes for new P8 features
such as transactional memory,...
There's also one powerpc KVM patch that I requested that adds two
missing functions to our in-kernel interrupt controller support which
is itself a new 3.10 feature. These are defined by the base
hypervisor specification. We didn't implement them originally because
Linux doesn't use them but they are simple and I'm not comfortable
having a half-implemented interface in 3.10 and having to deal with
versionning etc... later when something starts needing those calls.
They cannot be emulated in qemu when using in-kernel interrupt
controller (not enough shared state).
Just added a last minute patch to fix a typo introducing a breakage in
our cputable for Power7+ processors, sorry about that, but the
regression it fixes just hurt me :-)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/cputable: Fix typo on P7+ cputable entry
powerpc/perf: Add missing SIER support
powerpc/perf: Revert to original NO_SIPR logic
powerpc/pci: Remove the unused variables in pci_process_bridge_OF_ranges
powerpc/pci: Remove the stale comments of pci_process_bridge_OF_ranges
powerpc/pseries: Always enable CONFIG_HOTPLUG_CPU on PSERIES SMP
powerpc/kvm/book3s: Add support for H_IPOLL and H_XIRR_X in XICS emulation
powerpc/32bit:Store temporary result in r0 instead of r8
powerpc/mm: Always invalidate tlb on hpte invalidate and update
powerpc/pseries: Improve stream generation comments in copypage/user
powerpc/pseries: Kill all prefetch streams on context switch
powerpc/cputable: Fix oprofile_cpu_type on power8
powerpc/mpic: Fix irq distribution problem when MPIC_SINGLE_DEST_CPU
powerpc/tm: Fix userspace stack corruption on signal delivery for active transactions
powerpc/tm: Move TM abort cause codes to uapi
powerpc/tm: Abort on emulation and alignment faults
powerpc/tm: Update cause codes documentation
powerpc/tm: Make room for hypervisor in abort cause codes
|
|
Fix a typo in setting COMMON_USER2_POWER7 bits to .cpu_user_features2
cpu specs table.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit 8f61aa3 "Add support for SIER" missed updates to siar_valid()
and perf_get_data_addr().
In both cases we need to check the SIER instead of mmcra.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This is a revert and then some of commit 860aad7 "Add regs_no_sipr()".
This workaround was only needed on early chip versions.
As before NO_SIPR becomes a static flag of the PMU struct.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The codes which ever used these two variables have gone. Throw away
them too.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
These comments already don't apply to the current code. So just remove
them.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Adam Lackorzynski reported the following build failure on
!CONFIG_HOTPLUG_CPU configuration:
CC arch/powerpc/kernel/rtas.o
arch/powerpc/kernel/rtas.c: In function ‘rtas_cpu_state_change_mask’:
arch/powerpc/kernel/rtas.c:843:4: error: implicit declaration of function ‘cpu_down’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[1]: *** [arch/powerpc/kernel/rtas.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
The build fails because cpu_down() is defined only under CONFIG_HOTPLUG_CPU.
Looking further, the mobility code in pseries is one of the call-sites which
uses rtas_ibm_suspend_me(), which in turn calls rtas_cpu_state_change_mask().
And the mobility code is unconditionally compiled-in (it does not fall under
any Kconfig option). And commit 120496ac (powerpc: Bring all threads online
prior to migration/hibernation) which introduced this build regression is
critical for the proper functioning of the migration code. So it appears
that the only solution to this problem is to enable CONFIG_HOTPLUG_CPU if
SMP is enabled on PPC_PSERIES platforms. So make that change in the Kconfig.
Reported-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This adds the remaining two hypercalls defined by PAPR for manipulating
the XICS interrupt controller, H_IPOLL and H_XIRR_X. H_IPOLL returns
information about the priority and pending interrupts for a virtual
cpu, without changing any state. H_XIRR_X is like H_XIRR in that it
reads and acknowledges the highest-priority pending interrupt, but it
also returns the timestamp (timebase register value) from when the
interrupt was first received by the hypervisor. Currently we just
return the current time, since we don't do any software queueing of
virtual interrupts inside the XICS emulation code.
These hcalls are not currently used by Linux guests, but may be in
future.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit a9c4e541ea9b22944da356f2a9258b4eddcc953b
"powerpc/kprobe: Complete kprobe and migrate exception frame"
introduced a regression:
While returning from exception handling in case of PREEMPT enabled,
_TIF_NEED_RESCHED bit is checked in TI_FLAGS (thread_info flag) of current
task. Only if this bit is set, it should continue with the process of
calling preempt_schedule_irq() to schedule highest priority task if
available.
Current code assumes that r8 contains TI_FLAGS and check this for
_TIF_NEED_RESCHED, but as r8 is modified in the code which executes before
this check, r8 no longer contains the expected TI_FLAGS information.
As a result check for comparison with _TIF_NEED_RESCHED was failing even if
NEED_RESCHED bit is set in the current thread_info flag. Due to this,
preempt_schedule_irq() and in turn scheduler was not getting called even if
highest priority task is ready for execution.
So, store temporary results in r0 instead of r8 to prevent r8 from getting
modified as subsequent code is dependent on its value.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
CC: <stable@vger.kernel.org> [v3.7+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If a hash bucket gets full, we "evict" a more/less random entry from it.
When we do that we don't invalidate the TLB (hpte_remove) because we assume
the old translation is still technically "valid". This implies that when
we are invalidating or updating pte, even if HPTE entry is not valid
we should do a tlb invalidate.
This was a regression introduced by b1022fbd293564de91596b8775340cf41ad5214c
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
No code changes, just documenting what's happening a little better.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On context switch, we should have no prefetch streams leak from one
userspace process to another. This frees up prefetch resources for the
next process.
Based on patch from Milton Miller.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Maynard informed me that neither the oprofile kernel module nor oprofile
userspace has been updated to support that "legacy" oprofile module
interface for power8, which is indicated by "ppc64/power8." This results
in no samples. The solution is to default to the "timer" type, instead.
The raw entry also should be updated, as "ppc64/ibm-compat-v1" indicates
to oprofile userspace to use "compatibility events" which are obsolete
in ISA 2.07.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
For the mpic with a flag MPIC_SINGLE_DEST_CPU, only one bit should be
set in interrupt destination registers.
The code is applicable to 64-bit platforms as well as 32-bit.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
transactions
When in an active transaction that takes a signal, we need to be careful with
the stack. It's possible that the stack has moved back up after the tbegin.
The obvious case here is when the tbegin is called inside a function that
returns before a tend. In this case, the stack is part of the checkpointed
transactional memory state. If we write over this non transactionally or in
suspend, we are in trouble because if we get a tm abort, the program counter
and stack pointer will be back at the tbegin but our in memory stack won't be
valid anymore.
To avoid this, when taking a signal in an active transaction, we need to use
the stack pointer from the checkpointed state, rather than the speculated
state. This ensures that the signal context (written tm suspended) will be
written below the stack required for the rollback. The transaction is aborted
becuase of the treclaim, so any memory written between the tbegin and the
signal will be rolled back anyway.
For signals taken in non-TM or suspended mode, we use the
normal/non-checkpointed stack pointer.
Tested with 64 and 32 bit signals
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
These cause codes are usable by userspace, so let's export to uapi.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If we are emulating an instruction inside an active user transaction that
touches memory, the kernel can't emulate it as it operates in transactional
suspend context. We need to abort these transactions and send them back to
userspace for the hardware to rollback.
We can service these if the user transaction is in suspend mode, since the
kernel will operate in the same suspend context.
This adds a check to all alignment faults and to specific instruction
emulations (only string instructions for now). If the user process is in an
active (non-suspended) transaction, we abort the transaction go back to
userspace allowing the HW to roll back the transaction and tell the user of the
failure. This also adds new tm abort cause codes to report the reason of the
persistent error to the user.
Crappy test case here http://neuling.org/devel/junkcode/aligntm.c
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
PAPR carves out 0xff-0xe0 for hypervisor use of transactional memory software
abort cause codes. Unfortunately we don't respect this currently.
Below fixes this to move our cause codes to below this region.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9 only
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Module compilation issues (symbol not exported).
- Plug a hole where user space can bring the kernel down.
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: don't kill the kernel on a bad esr from el0
arm64: treat unhandled compat el0 traps as undef
arm64: Do not report user faults for handled signals
arm64: kernel: compiling issue, need 'EXPORT_SYMBOL(clear_page)'
|
|
Rather than completely killing the kernel if we receive an esr value we
can't deal with in the el0 handlers, send the process a SIGILL and log
the esr value in the hope that we can debug it. If we receive a bad esr
from el1, we'll die() as before.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: stable@vger.kernel.org
|
|
Currently, if a compat process reads or writes from/to a disabled
cp15/cp14 register, the trap is not handled by the el0_sync_compat
handler, and the kernel will head to bad_mode, where it will die(), and
oops(). For 64 bit processes, disabled system register accesses are
currently treated as unhandled instructions.
This patch modifies entry.S to treat these unhandled traps as undefined
instructions, sending a SIGILL to userspace. This gives processes a
chance to handle this and stop using inaccessible registers, and
prevents further issues in the kernel as a result of the die().
Reported-by: Johannes Jensen <Johannes.Jensen@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
- Three EFI-related fixes
- Two early memory initialization fixes
- build fix for older binutils
- fix for an eager FPU performance regression -- currently we don't
allow the use of the FPU at interrupt time *at all* in eager mode,
which is clearly wrong.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Allow FPU to be used at interrupt time even with eagerfpu
x86, crc32-pclmul: Fix build with older binutils
x86-64, init: Fix a possible wraparound bug in switchover in head_64.S
x86, range: fix missing merge during add range
x86, efi: initial the local variable of DataSize to zero
efivar: fix oops in efivar_update_sysfs_entries() caused by memory reuse
efivarfs: Never return ENOENT from firmware again
|
|
With the addition of eagerfpu the irq_fpu_usable() now returns false
negatives especially in the case of ksoftirqd and interrupted idle task,
two common cases for FPU use for example in networking/crypto. With
eagerfpu=off FPU use is possible in those contexts. This is because of
the eagerfpu check in interrupted_kernel_fpu_idle():
...
* For now, with eagerfpu we will return interrupted kernel FPU
* state as not-idle. TBD: Ideally we can change the return value
* to something like __thread_has_fpu(current). But we need to
* be careful of doing __thread_clear_has_fpu() before saving
* the FPU etc for supporting nested uses etc. For now, take
* the simple route!
...
if (use_eager_fpu())
return 0;
As eagerfpu is automatically "on" on those CPUs that also have the
features like AES-NI this patch changes the eagerfpu check to return 1 in
case the kernel_fpu_begin() has not been said yet. Once it has been the
__thread_has_fpu() will start returning 0.
Notice that with eagerfpu the __thread_has_fpu is always true initially.
FPU use is thus always possible no matter what task is under us, unless
the state has already been saved with kernel_fpu_begin().
[ hpa: this is a performance regression, not a correctness regression,
but since it can be quite serious on CPUs which need encryption at
interrupt time I am marking this for urgent/stable. ]
Signed-off-by: Pekka Riikonen <priikone@iki.fi>
Link: http://lkml.kernel.org/r/alpine.GSO.2.00.1305131356320.18@git.silcnet.org
Cc: <stable@vger.kernel.org> v3.7+
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
binutils prior to 2.18 (e.g. the ones found on SLE10) don't support
assembling PEXTRD, so a macro based approach like the one for PCLMULQDQ
in the same file should be used.
This requires making the helper macros capable of recognizing 32-bit
general purpose register operands.
[ hpa: tagging for stable as it is a low risk build fix ]
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/51A6142A02000078000D99D8@nat28.tlf.novell.com
Cc: Alexander Boyko <alexander_boyko@xyratex.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <stable@vger.kernel.org> v3.9
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
- Use proper error paths
- Clean up APIC IPI usage (incorrect arguments)
- Delay XenBus frontend resume is backend (xenstored) is not running
- Fix build error with various combinations of CONFIG_
* tag 'stable/for-linus-3.10-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus_client.c: correct exit path for xenbus_map_ring_valloc_hvm
xen-pciback: more uses of cached MSI-X capability offset
xen: Clean up apic ipi interface
xenbus: save xenstore local status for later use
xenbus: delay xenbus frontend resume if xenstored is not running
xmem/tmem: fix 'undefined variable' build error.
|
|
Merge mn10300 fixes from David Howells.
* emailed patches from David Howells <dhowells@redhat.com>:
MN10300: Need pci_iomap() and __pci_ioport_map() defining
MN10300: ASB2305's PCI code needs the definition of XIRQ1
MN10300: Enable IRQs more in system call exit work path
MN10300: Fix ret_from_kernel_thread
|
|
Include the generic definitions of pci_iomap() and __pci_ioport_map()
otherwise we can get errors like:
lib/pci_iomap.c: In function 'pci_iomap':
lib/pci_iomap.c:37: error: implicit declaration of function '__pci_ioport_map'
lib/pci_iomap.c:37: warning: return makes pointer from integer without a cast
and:
drivers/pci/quirks.c: In function 'disable_igfx_irq':
drivers/pci/quirks.c:2893: error: implicit declaration of function 'pci_iomap'
drivers/pci/quirks.c:2893: warning: initialization makes pointer from integer without a cast
drivers/pci/quirks.c: In function 'reset_ivb_igd':
drivers/pci/quirks.c:3133: warning: assignment makes pointer from integer without a cast
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ken Cox <jkc@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code for PCI in the ASB2305 needs the definition of XIRQ1 from proc/irq.h
otherwise the following error appears:
arch/mn10300/unit-asb2305/pci.c: In function 'unit_pci_init':
arch/mn10300/unit-asb2305/pci.c:481: error: 'XIRQ1' undeclared (first use in this function)
arch/mn10300/unit-asb2305/pci.c:481: error: (Each undeclared identifier is reported only once
arch/mn10300/unit-asb2305/pci.c:481: error: for each function it appears in.)
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ken Cox <jkc@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Enable IRQs when calling schedule() for TIF_NEED_RESCHED and
do_notify_resume(). If interrupts are enabled during do_notify_resume(), a
warning can be seen (see lower down).
Whilst we're at it, resume_userspace can be made local to entry.S as it is not
called outside of there and it can be merged with the part of work_resched that
occurs after schedule() is called.
WARNING: at kernel/softirq.c:160 local_bh_enable+0x42/0xa0()
Call Trace:
local_bh_enable+0x42/0xa0
unix_release_sock+0x86/0x23c
unix_release+0x20/0x28
sock_release+0x17/0x88
sock_close+0x20/0x28
__fput+0xc9/0x1fc
____fput+0xb/0x10
task_work_run+0x64/0x78
do_notify_resume+0x53d/0x544
work_notifysig+0xa/0xc
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ken Cox <jkc@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ret_from_kernel_thread needs to set A2 to the thread_info pointer before
jumping to syscall_exit.
Without this, we never correctly start userspace.
This was caused by the rejuggling of the fork/exec paths in commit
ddf23e87a804 ("mn10300: switch to saner kernel_execve() semantics")
Reported-by: Ken Cox <jkc@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ken Cox <jkc@redhat.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin-control fixes from Linus Walleij:
- Six patches fixing up the suspend/resume and wakeup handling of the
Samsung and Exynos drivers.
- Errorpath fixes for four different drivers. All on the probe()
errorpath.
- Make the debugfs code for pin config take the right mutex.
* tag 'pinctrl-fixes-v3.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinconf: take the right mutex
pinctrl: sunxi: fix error return code in sunxi_pinctrl_probe()
pinctrl: exynos: Handle suspend/resume of GPIO EINT registers
pinctrl: samsung: Allow per-bank SoC-specific private data
pinctrl: samsung: Add support for SoC-specific suspend/resume callbacks
pinctrl: Don't override the error code in probe error handling
ARM: EXYNOS: Fix EINT wake-up mask configuration when pinctrl is used
pinctrl: exynos: Add support for set_irq_wake of wake-up EINTs
pinctrl: samsung: fix suspend/resume functionality
|
|
Commit f447d56d36af18c5104ff29dcb1327c0c0ac3634 introduced the
implementation of the PV apic ipi interface. But there were some
odd things (it seems none of which cause really any issue but
maybe they should be cleaned up anyway):
- xen_send_IPI_mask_allbutself (and by that xen_send_IPI_allbutself)
ignore the passed in vector and only use the CALL_FUNCTION_SINGLE
vector. While xen_send_IPI_all and xen_send_IPI_mask use the vector.
- physflat_send_IPI_allbutself is declared unnecessarily. It is never
used.
This patch tries to clean up those things.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Exynos fixes from Olof Johansson:
"Here's a shorter set of fixes for 3.10, all for Samsung Exynos
platforms.
It also includes a defconfig update so that exynos_defconfig provides
a meaningful set of drivers to boot an unmodified kernel on the
Samsung ARM-based Chromebooks."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: defconfig update
ARM: SAMSUNG: Add names to fimd0 IRQ resources
ARM: EXYNOS: fix software reset logic for EXYNOS5440 SOC
ARM: EXYNOS: Fix support of Exynos4210 rev0 SoC
ARM: dts: Enabling samsung-usb2phy driver for exynos5250
|
|
This turns on a number of configs that are useful on the Chromebook, but also
good to have on in general:
* USB host and MMC drivers(!)
* I2C GPIO arbitration driver
* CYAPA trackpad driver
* simplefb
* CROS EC and keyboard drivers
* S5M8767 driver
* MAX77686 drivers
* MAX8997 driver
* DEVTMPFS + mount
* DM_CRYPT (as module)
* CRYPTOLOOP
* HIGHMEM
* PRINTK timestamps
This also turns off DEBUG_LL, and switches the hardcoded Samsung lowlevel
uart to uart 3 (which is only used to show the "uncompressing kernel"
message at boot, it seems).
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
In head_64.S, a switchover has been used to handle kernel crossing
1G, 512G boundaries.
And commit 8170e6bed465b4b0c7687f93e9948aca4358a33b
x86, 64bit: Use a #PF handler to materialize early mappings on demand
said:
During the switchover in head_64.S, before #PF handler is available,
we use three pages to handle kernel crossing 1G, 512G boundaries with
sharing page by playing games with page aliasing: the same page is
mapped twice in the higher-level tables with appropriate wraparound.
But from the switchover code, when we set up the PUD table:
114 addq $4096, %rdx
115 movq %rdi, %rax
116 shrq $PUD_SHIFT, %rax
117 andl $(PTRS_PER_PUD-1), %eax
118 movq %rdx, (4096+0)(%rbx,%rax,8)
119 movq %rdx, (4096+8)(%rbx,%rax,8)
It seems line 119 has a potential bug there. For example,
if the kernel is loaded at physical address 511G+1008M, that is
000000000 111111111 111111000 000000000000000000000
and the kernel _end is 512G+2M, that is
000000001 000000000 000000001 000000000000000000000
So in this example, when using the 2nd page to setup PUD (line 114~119),
rax is 511.
In line 118, we put rdx which is the address of the PMD page (the 3rd page)
into entry 511 of the PUD table. But in line 119, the entry we calculate from
(4096+8)(%rbx,%rax,8) has exceeded the PUD page. IMO, the entry in line
119 should be wraparound into entry 0 of the PUD table.
The patch fixes the bug.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/5191DE5A.3020302@cn.fujitsu.com
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@vger.kernel.org> v3.9
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
