| Age | Commit message (Collapse) | Author |
|---|
|
Linux 3.5-rc4 contains some bug fixes which overlap with new features.
|
|
Coult -> Could
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull KVM fixes from Avi Kivity:
"Fixing a scheduling-while-atomic bug in the ppc code, and a bug which
allowed pci bridges to be assigned to guests."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Drop locks around call to kvmppc_pin_guest_page
KVM: Fix PCI header check on device assignment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Nothing very controversial in here. Most of the fixes are for OMAP
this time around, with some orion/kirkwood and a tegra patch mixed in."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion: Fix Virtual/Physical mixup with watchdog
ARM: Kirkwood: clk_register_gate_fn: add fn assignment
ARM: Orion5x - Restore parts of io.h, with rework
ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
ARM: OMAP2+: mux: fix sparse warning
ARM: OMAP2+: CM: increase the module disable timeout
ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
ARM: tegra: make tegra_cpu_reset_handler_enable() __init
ARM: OMAP: PM: Lock clocks list while generating summary
ARM: iconnect: Remove include of removed linux/spi/orion_spi.h
|
|
The orion watchdog is expecting to be passed the physcial address of
the hardware, and will ioremap() it to give a virtual address it will
use as the base address for the hardware. However, when creating the
platform resource record, a virtual address was being used.
Add the necassary #define's so we can pass the physical address as
expected.
Tested on Kirkwood and Orion5x.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
In commit:
98d9986 ARM: Kirkwood: Replace clock gating
the kirkwood clock gating has been reworked. A custom variant of
clock gating, that calls a custom function before gating the clock
off, has been introduced. However in clk_register_gate_fn() this
custom function "fn" is never assigned.
This patch adds the missing fn assignment.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 4d5fc58dbe34b78157c05b319669bb3e064ba8bd (ARM: remove bunch of
now unused mach/io.h files) removed the orion5x io.h. Unfortunately,
this is still needed for the definition of IO_SPACE_LIMIT which
overrides the default 64K. All Orion based systems have 1Mbyte of IO
space per PCI[e] bus, and try to request_resource() this size. Orion5x
has two such PCI buses.
It is likely that the original, removed version, was broken. This
version might be less broken. However, it has not been tested on
hardware with a PCI card, let alone hardware with a PCI card with IO
capabilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley (as per Tony Lindgren's request):
"Some uncontroversial OMAP clock, hwmod, and compiler warning fixes for 3.5-rc"
* tag 'omap-fixes-a-for-3.5rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
ARM: OMAP2+: mux: fix sparse warning
ARM: OMAP2+: CM: increase the module disable timeout
ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
ARM: OMAP: PM: Lock clocks list while generating summary
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here are a few fixes with the biggest one being fix for Beagle DVI
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier."
* tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
|
|
As per the OMAP4 documentation, audio over HDMI must be transmitted in
no-idle mode. This patch adds the HWMOD_SWSUP_SIDLE so that omap_hwmod uses
no-idle/force-idle settings instead of smart-idle mode.
This is required as the DSS interface clock is used as functional clock
for the HDMI wrapper audio FIFO. If no-idle mode is not used, audio could
be choppy, have bad quality or not be audible at all.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
[b-cousson@ti.com: Update the subject and align the .flags
location with the script template]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit bbd707acee279a61177a604822db92e8164d00db ("ARM: omap2: use
machine specific hook for late init") resulted in the addition of this
sparse warning:
arch/arm/mach-omap2/mux.c:791:12: warning: symbol 'omap_mux_late_init' was not declared. Should it be static?
Fix by including the header file containing the prototype.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
|
|
Increase the timeout for disabling an IP block to five milliseconds.
This is to handle the usb_host_fs idle latency, which takes almost
four milliseconds after a host controller reset.
This is the second of two patches needed to resolve the following
boot warning:
omap_hwmod: usb_host_fs: _wait_target_disable failed
Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for finding
an unrelated hunk in a previous version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Tero Kristo <t-kristo@ti.com>
|
|
Until the OMAP4 code is converted to disable the use of the clock
framework-based clockdomain enable/disable sequence, any clock used as
a hwmod main_clk must have a clockdomain associated with it. This
patch populates some clock structure clockdomain names to resolve the
following warnings during kernel init:
omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
omap_hwmod: trace_clk_div_ck: missing clockdomain for trace_clk_div_ck.
omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
omap_hwmod: ddrphy_ck: missing clockdomain for ddrphy_ck.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
The 32k sync timer IP block target idle modes in the hwmod data are
incorrect. The IP block does not support any smart-idle modes.
Update the data to reflect the correct modes.
This problem was initially identified and a diff fragment posted to
the lists by Benoît Cousson <b-cousson@ti.com>. A patch description
bug in the first version was also identified by Benoît.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
|
|
If an IP is configured in Smart-Standby-Wakeup, when disabling wakeup feature the
IP will not go back to Smart-Standby, but will remain in Smart-Standby-Wakeup.
Signed-off-by: Djamil Elaidi <d-elaidi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and printk fixes from Greg Kroah-Hartman:
"Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: max8997: Add missing kfree for info->edev in max8997_muic_remove()
extcon: Set platform drvdata in gpio_extcon_probe() and fix irq leak
extcon: Fix wrong index in max8997_extcon_cable[]
kmsg - kmsg_dump() fix CONFIG_PRINTK=n compilation
printk: return -EINVAL if the message len is bigger than the buf size
printk: use mutex lock to stop syslog_seq from going wild
kmsg - kmsg_dump() use iterator to receive log buffer content
vme: change maintainer e-mail address
Extcon: Don't try to create duplicate link names
driver core: fixup reversed deferred probe order
printk: Fix alignment of buf causing crash on ARM EABI
Tools: hv: verify origin of netlink connector message
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg Kroah-Hartman:
"Here are 3 patches resolving a boot regression (the mop500 fix), a
build warning fix, and a kernel-doc fix. All tiny, but should go into
the final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial/amba-pl011: move custom pin control to driver
serial: fix serial_txx9.c build warning/typo
serial: fix kernel-doc warnings in 8250.c
|
|
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
|
|
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cleanups:
- Include <asm/sections.h>,
- Remove the (different) extern declarations,
- Remove the no longer needed address-of ('&') operators,
- Remove the superfluous casts, use proper printk formatting instead.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Nowadays it should use __bss_start and __bss_stop
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cleanups:
- Include <asm/sections.h>,
- Remove the (different) extern declarations,
- Remove the no longer needed address-of ('&') operators,
- Use %p to format pointer differences.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On Ubuntu, /bin/sh is a symlink to dash, which does not support "test -a".
This causes messages like
test: 1: -a: unexpected operator
test: 1: -a: unexpected operator
and link failures like
(.init.text+0x132): undefined reference to `platform_init'
due to the appropriate platform code not being compiled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit a2d063ac216c161 ("extable, core_kernel_data(): Make sure all archs
define _sdata") missed xtensa. Xtensa does have a start of data marker,
but calls it _fdata, causing
kernel/built-in.o:(.text+0x964): undefined reference to `_sdata'
_stext was already defined, but it was duplicated by _fdata.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the x86 32bit PAE CONFIG_TRANSPARENT_HUGEPAGE=y case while holding the
mmap_sem for reading, cmpxchg8b cannot be used to read pmd contents under
Xen.
So instead of dealing only with "consistent" pmdvals in
pmd_none_or_trans_huge_or_clear_bad() (which would be conceptually
simpler) we let pmd_none_or_trans_huge_or_clear_bad() deal with pmdvals
where the low 32bit and high 32bit could be inconsistent (to avoid having
to use cmpxchg8b).
The only guarantee we get from pmd_read_atomic is that if the low part of
the pmd was found null, the high part will be null too (so the pmd will be
considered unstable). And if the low part of the pmd is found "stable"
later, then it means the whole pmd was read atomically (because after a
pmd is stable, neither MADV_DONTNEED nor page faults can alter it anymore,
and we read the high part after the low part).
In the 32bit PAE x86 case, it is enough to read the low part of the pmdval
atomically to declare the pmd as "stable" and that's true for THP and no
THP, furthermore in the THP case we also have a barrier() that will
prevent any inconsistent pmdvals to be cached by a later re-read of the
*pmd.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM fixes from Russell King:
"This includes three MMCI changes - one to fix up the wrong version of
the DT support patch which was merged, and two to make deferred
probing work. It also includes a fix to the OMAP SPI driver which is
causing a boot time warning.
The remainder are very minor ARM fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
SPI: fix over-eager devm_xxx() conversion
ARM: 7427/1: mmc: mmci: Defer probe() in case of yet uninitialized GPIOs
ARM: 7426/1: mmc: mmci: Remove wrong error handling of gpio 0
ARM: 7425/1: extable: ensure fixup entries are 4-byte aligned
ARM: 7421/1: bpf_jit: BPF_S_ANC_ALU_XOR_X support
ARM: 7423/1: kprobes: run t32_simulate_ldr_literal() without insn slot
ARM: 7422/1: mmc: mmci: Allocate platform memory during Device Tree boot
|
|
Commit e813a55eb9c9bc6c8039fb16332cf43402125b30 ("OMAP: board-files:
remove custom PD GPIO handling for DVI output") moved TFP410 chip's
powerdown-gpio handling from the board files to the tfp410 driver. One
gpio_request_one(powerdown-gpio, ...) was mistakenly left unremoved in
the Beagle board file. This causes the tfp410 driver to fail to request
the gpio on Beagle, causing the driver to fail and thus the DVI output
doesn't work.
This patch removes several boot errors from board-omap3beagle.c:
- gpio_request: gpio--22 (DVI reset) status -22
- Unable to get DVI reset GPIO
There is a combination of leftover code and revision confusion.
Additionally, xM support is currently a hack.
For original Beagleboard this removes the double initialization of GPIO
170, properly configures it as an output, and wraps the initialization
in an if block so that xM does not attempt to request it.
For Beagleboard xM it removes reference to GPIO 129 which was part
of rev A1 and A2 designs, but never functioned. It then properly assigns
beagle_dvi_device.reset_gpio in beagle_twl_gpio_setup and removes the
hack of initializing it high. Additionally, it uses
gpio_set_value_cansleep since this GPIO is connected through i2c.
Unfortunately, there is no way to tell the difference between xM A2 and
A3. However, GPIO 129 does not function on rev A1 and A2, and the TWL
GPIO used on A3 and beyond is not used on rev A1 and A2, there are no
problems created by this fix.
Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When booting with device-tree on an OMAP2420H4, the kernel is hanging when
initialising the interrupts and following kernel dumps is seen ...
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at arch/arm/mach-omap2/irq.c:271 omap_intc_of_init+0x50/0xb4()
[ 0.000000] unable to get intc registers
[ 0.000000] Modules linked in:
[ 0.000000] [<c001befc>] (unwind_backtrace+0x0/0xf4) from [<c0040c34>] (warn_slowpath_common+0x4c/0x64)
[ 0.000000] [<c0040c34>] (warn_slowpath_common+0x4c/0x64) from [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40)
[ 0.000000] [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40) from [<c066b8a4>] (omap_intc_of_init+0x50/0xb4)
[ 0.000000] [<c066b8a4>] (omap_intc_of_init+0x50/0xb4) from [<c0688b70>] (of_irq_init+0x144/0x288)
[ 0.000000] [<c0688b70>] (of_irq_init+0x144/0x288) from [<c0663294>] (init_IRQ+0x14/0x1c)
[ 0.000000] [<c0663294>] (init_IRQ+0x14/0x1c) from [<c06607fc>] (start_kernel+0x198/0x304)
[ 0.000000] [<c06607fc>] (start_kernel+0x198/0x304) from [<80008044>] (0x80008044)
[ 0.000000] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.000000] of_irq_init: children remain, but no parents
The OMAP2 interrupt controller binding is missing the number of interrupts and
interrupt controller register address. Adding these fixes the problem.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Here's one more gpio_to_irq conversion that we missed
earlier. Tested with n800 in gadget mode using USB_ETH.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 62285963 (usb: musb: drop a gigantic amount of ifdeferry)
got rid of a bunch of ifdefs in the MUSB code. Looks like the
platform init code is still using these dropped defines though,
which in many cases results the board defaulting always to host
mode.
Currently the situation is that USB_MUSB_HDRC is the main
Kconfig option with additional USB_GADGET_MUSB_HDRC so only
these two should be used to select between host and OTG mode.
Fix the situation for omaps. The following users should fix the
platform init code in a similar way:
Dropped Kconfig option Current users
USB_MUSB_OTG blackfin, davinci, not in Kconfigs
USB_MUSB_PERIPHERAL davinci, not in Kconfigs
USB_MUSB_HOST davinci, not in Kconfigs
USB_MUSB_HDRC_HCD blackfin, not in Kconfigs
USB_MUSB_OTG blackfin, not in Kconfigs
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of changes are fairly small and driver-specific.
A remaining regression fix for USB-audio sync pipe check, a fix for
HD-audio power-up sequence, fixes for ASoC pxa-ssp compile issues, and
bunch of ASoC codec and trivial fix patches."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: 6fire: use NULL instead of 0 for pointer assignment
ALSA: hda - Handle open while transitioning to D3.
ALSA: snd-usb: make snd_usb_substream_capture_trigger static
ALSA: snd-usb: fix sync pipe check
ASoC: tegra+wm8903: turn of mic detect when card is removed
ASoC: wm8996: Mark the CODEC as cache only when powering off on boot
ASoC: wm8996: Move reset before the initial regulator disable
ASoC: wm8996: Remove spurious regulator_bulk_free()
ASoC: wm8904: Fix cache only management
ASoC: wm8904: Fix GPIO and MICBIAS initialisation for regmap conversion
ASoC: fix pxa-ssp compiling issue under mach-mmp
ARM: MMP: add pxa910-ssp into ssp_id_table
|
|
At the moment we call kvmppc_pin_guest_page() in kvmppc_update_vpa()
with two spinlocks held: the vcore lock and the vcpu->vpa_update_lock.
This is not good, since kvmppc_pin_guest_page() calls down_read() and
get_user_pages_fast(), both of which can sleep. This bug was introduced
in 2e25aa5f ("KVM: PPC: Book3S HV: Make virtual processor area
registration more robust").
This arranges to drop those spinlocks before calling
kvmppc_pin_guest_page() and re-take them afterwards. Dropping the
vcore lock in kvmppc_run_core() means we have to set the vcore_state
field to VCORE_RUNNING before we drop the lock, so that other vcpus
won't try to run this vcore.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This solves a section mismatch warning. I hadn't noticed this before,
because my compiler was inlining tegra_cpu_reset_handler_enable() inside
tegra_cpu_reset_handler_init(), which is already __init, but I switched
compilers and it stopped doing that.
Cc: <stable@kernel.org> # v3.4
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit a53025724052b2b1edbc982a4a248784638f563d (OMAP: Add debugfs
node to show the summary of all clocks) introduced clock summary,
however, we are interested in seeing snapshot of the clock state, not
in dynamically changing clock configurations as the data provided by
clock summary will then be useless for debugging configuration
issues. So, hold the common lock when dumping the clock summary.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
[nm@ti.com: added commit message]
Signed-off-by: Nishanth Menon <nm@ti.com>
[paul@pwsan.com: minor edits to commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
v3.5-rc1 fails to build when DT and iconnect is enabled because of
this now none existant include file.
Also remove the other two SPI include files, which are not needed
with the move to DT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A bit larger set than usual, unfortunately -- I've been sitting on
them longer than I meant to so it's really more like 2 -rc pull
requests in one, volume-wise.
Nearly everything is fixes for fallout from the merge window, or other
fixes for bugs. The one exception is the highbank L2-enablement
patch, but it was contained enough that I picked it up anyway:
- i.MX fixes, mostly for clock and pinctrl changes
- OMAP fixes, mostly PM-related
- A patch to enable L2 on highbank
- A couple of fixes for PXA, Kirkwood, Versatile"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: Kirkwood: Fix clk problems modular ethernet driver
arm: versatile: fix and enable PCI I/O space
ARM: highbank: Add smc calls to enable/disable the L2
ARM i.MX imx21ads: Fix overlapping static i/o mappings
ARM: imx6: exit coherency when shutting down a cpu
ARM: mx51: Add pinctrl_provide_dummies()
ARM: mx31: Add pinctrl_provide_dummies()
ARM: OMAP2+: Fix compile for CONFIG_TIDSPBRIDGE platform init code
ARM: OMAP3: Fix omap3_l3_block_irq warning when CONFIG_BUG is not set
ARM: OMAP: Fix MMC_OMAP build when only MMC_OMAP_HS is selected
OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
ARM: mmp: fix missing cascade_irq in irq handler
ARM: dts: update memory size on brownstone
ARM i.MX27 Visstrim M10: fix gpio handling.
ARM i.MX53: Fix PLL4 base address
ARM i.MX pllv2: make round_rate accurate
ARM i.MX pllv2: use standard register set unconditionally
ARM: OMAP: Fix lis3lv02d accelerometer to use gpio_to_irq
ARM: imx: only call l2x0_init if it's available
ARM: imx: only specify i2c device type once
...
|
|
When the ethernet driver was built as a module, it would lock the
machine when loaded. At boot the ethernet clks are unused, so get
turned off. Later, when the module is loaded, the probe function
would access the hardware before the clock was restarted, and the
machine would lock. It has also been determined that when the clk is
turned off, the interface forgets its MAC address, which for most
systems, is set by the boot loader.
When the machine setup file creates a platform device for the
interface, prepare and enable the clock for the interface. This will
ensure it is not turned off. However, if the setup file only
instantiates one platform device, the other will have its clk
disabled, thus maybe saving a little power.
Report-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
With commit 4d5fc58dbe34b (ARM: remove bunch of now unused
mach/io.h files), the I/O space setup was completely broken on
versatile. This patch fixes that and prepares for further
I/O space clean-up.
I/O space handling on the versatile platform is currently
broken in multiple ways. Most importantly, the ports do
not get mapped into the virtual address space at all.
Also, there is some amount of confusion between PCI I/O
space and other statically mapped MMIO registers in the
platform code:
* The __io_address() macro that is used to access the
platform register maps to the same __io macro that gets
used for I/O space.
* The IO_SPACE_LIMIT is set to a value that is much larger
than the total available space.
* The I/O resource of the PCI bus is set to the physical
address of the mapping, which is way outside of the
actual I/O space limit as well as the address range that
gets decoded by traditional PCI cards.
* No attempt is made to stay outside of the ISA port range
that some device drivers try access.
* No resource gets requested as a child of ioport_resource,
but an IORESOURCE_IO type mapping gets requested
as a child of iomem_resource.
This patch attempts to correct all of the above. This makes
it possible to use virtio-pci based virtual devices as well
as actual PCI cards including those with legacy ISA port
ranges like VGA.
Some of the issues seem to be duplicated on other platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[rob: update to 3.5-rc2 and io.h cleanup related changes]
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* 'fixes' of git://github.com/hzhuang1/linux:
ARM: mmp: fix missing cascade_irq in irq handler
ARM: dts: update memory size on brownstone
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile update from Chris Metcalf:
"This one-line bug fix unbreaks glibc robust mutexes (among other
things no doubt), from code merged in during the 3.5 merge window but
which we had been running internally at Tilera for almost a year."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: fix bug in get_user() for 4-byte values
|
|
The definition of 32-bit values in the 64-bit tilegx architecture is that
they should be sign-extended regardless of whether they are considered
signed or unsigned by the compiler. Accordingly, we need to use an
"ld4s" rather than "ld4u" to load and sign-extend for get_user().
This fixes glibc bug 14238 (see http://sourceware.org/bugzilla),
introduced during the 3.5 merge window.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Fixup entries in the kernel exception tables should be 4-byte aligned
since we return directly to them when handling a faulting instruction in
the kernel.
This patch adds the missing align directives to the fixup entries.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping fixes from Marek Szyprowski:
"A set of minor fixes for dma-mapping code (ARM and x86) required for
Contiguous Memory Allocator (CMA) patches merged in v3.5-rc1."
* 'fixes-for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
x86: dma-mapping: fix broken allocation when dma_mask has been provided
ARM: dma-mapping: fix debug messages in dmabounce code
ARM: mm: fix type of the arm_dma_limit global variable
ARM: dma-mapping: Add missing static storage class specifier
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
Pull PowerPC fix from Paul Mackerras:
"Just one commit, and a one-liner at that, but an important one;
without it hard_irq_disable() does nothing on powerpc."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
Make hard_irq_disable() actually hard-disable interrupts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull five Xen bug-fixes from Konrad Rzeszutek Wilk:
- When booting as PVHVM we would try to use PV console - but would not validate
the parameters causing us to crash during restore b/c we re-use the wrong event
channel.
- When booting on machines with SR-IOV PCI bridge we didn't check for the bridge
and tried to use it.
- Under AMD machines would advertise the APERFMPERF resulting in needless amount
of MSRs from the guest.
- A global value (xen_released_pages) was not subtracted at bootup when pages
were added back in. This resulted in the balloon worker having the wrong
account of how many pages were truly released.
- Fix dead-lock when xen-blkfront is run in the same domain as xen-blkback.
* tag 'stable/for-linus-3.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mark local pages as FOREIGN in the m2p_override
xen/setup: filter APERFMPERF cpuid feature out
xen/balloon: Subtract from xen_released_pages the count that is populated.
xen/pci: Check for PCI bridge before using it.
xen/events: Add WARN_ON when quick lookup found invalid type.
xen/hvc: Check HVM_PARAM_CONSOLE_[EVTCHN|PFN] for correctness.
xen/hvc: Fix error cases around HVM_PARAM_CONSOLE_PFN
xen/hvc: Collapse error logic.
|
|
Pull sparc update from David S. Miller:
"This just removes some sparc headers that were never, ever, used."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: remove two unused headers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Fix topology checks on AMD MCM CPUs
x86/mm: Fix some kernel-doc warnings
x86, um: Correct syscall table type attributes breaking gcc 4.8
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
watchdog: Quiet down the boot messages
perf/x86: Fix broken LBR fixup code
tracing: Have tracing_off() actually turn tracing off
|
|
Provide an iterator to receive the log buffer content, and convert all
kmsg_dump() users to it.
The structured data in the kmsg buffer now contains binary data, which
should no longer be copied verbatim to the kmsg_dump() users.
The iterator should provide reliable access to the buffer data, and also
supports proper log line-aware chunking of data while iterating.
Signed-off-by: Kay Sievers <kay@vrfy.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Reported-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Tested-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At present, hard_irq_disable() does nothing on powerpc because of
this code in include/linux/interrupt.h:
#ifndef hard_irq_disable
#define hard_irq_disable() do { } while(0)
#endif
So we need to make our hard_irq_disable be a macro. It was previously
a macro until commit 7230c56441 ("powerpc: Rework lazy-interrupt
handling") changed it to a static inline function.
Cc: stable@vger.kernel.org
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
--
arch/powerpc/include/asm/hw_irq.h | 3 +++
1 file changed, 3 insertions(+)
|
