Age | Commit message (Collapse) | Author |
|
kvm-next
Patch queue for ppc - 2014-05-30
In this round we have a few nice gems. PR KVM gains initial POWER8 support
as well as LE host awareness, ihe e500 targets can now properly run u-boot,
LE guests now work with PR KVM including KVM hypercalls and HV KVM guests
can now use huge pages.
On top of this there are some bug fixes.
Conflicts:
include/uapi/linux/kvm.h
|
|
On LPAR guest systems Linux enables the shadow SLB to indicate to the
hypervisor a number of SLB entries that always have to be available.
Today we go through this shadow SLB and disable all ESID's valid bits.
However, pHyp doesn't like this approach very much and honors us with
fancy machine checks.
Fortunately the shadow SLB descriptor also has an entry that indicates
the number of valid entries following. During the lifetime of a guest
we can just swap that value to 0 and don't have to worry about the
SLB restoration magic.
While we're touching the code, let's also make it more readable (get
rid of rldicl), allow it to deal with a dynamic number of bolted
SLB entries and only do shadow SLB swizzling on LPAR systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We didn't make use of SLB entry 0 because ... of no good reason. SLB entry 0
will always be used by the Linux linear SLB entry, so the fact that slbia
does not invalidate it doesn't matter as we overwrite SLB 0 on exit anyway.
Just enable use of SLB entry 0 for our shadow SLB code.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The code that delivered a machine check to the guest after handling
it in real mode failed to load up r11 before calling kvmppc_msr_interrupt,
which needs the old MSR value in r11 so it can see the transactional
state there. This adds the missing load.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This adds workarounds for two hardware bugs in the POWER8 performance
monitor unit (PMU), both related to interrupt generation. The effect
of these bugs is that PMU interrupts can get lost, leading to tools
such as perf reporting fewer counts and samples than they should.
The first bug relates to the PMAO (perf. mon. alert occurred) bit in
MMCR0; setting it should cause an interrupt, but doesn't. The other
bug relates to the PMAE (perf. mon. alert enable) bit in MMCR0.
Setting PMAE when a counter is negative and counter negative
conditions are enabled to cause alerts should cause an alert, but
doesn't.
The workaround for the first bug is to create conditions where a
counter will overflow, whenever we are about to restore a MMCR0
value that has PMAO set (and PMAO_SYNC clear). The workaround for
the second bug is to freeze all counters using MMCR2 before reading
MMCR0.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Current, when testing whether a page is dirty (when constructing the
bitmap for the KVM_GET_DIRTY_LOG ioctl), we test the C (changed) bit
in the HPT entries mapping the page, and if it is 0, we consider the
page to be clean. However, the Power ISA doesn't require processors
to set the C bit to 1 immediately when writing to a page, and in fact
allows them to delay the writeback of the C bit until they receive a
TLB invalidation for the page. Thus it is possible that the page
could be dirty and we miss it.
Now, if there are vcpus running, this is not serious since the
collection of the dirty log is racy already - some vcpu could dirty
the page just after we check it. But if there are no vcpus running we
should return definitive results, in case we are in the final phase of
migrating the guest.
Also, if the permission bits in the HPTE don't allow writing, then we
know that no CPU can set C. If the HPTE was previously writable and
the page was modified, any C bit writeback would have been flushed out
by the tlbie that we did when changing the HPTE to read-only.
Otherwise we need to do a TLB invalidation even if the C bit is 0, and
then check the C bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The dirty map that we construct for the KVM_GET_DIRTY_LOG ioctl has
one bit per system page (4K/64K). Currently, we only set one bit in
the map for each HPT entry with the Change bit set, even if the HPT is
for a large page (e.g., 16MB). Userspace then considers only the
first system page dirty, though in fact the guest may have modified
anywhere in the large page.
To fix this, we make kvm_test_clear_dirty() return the actual number
of pages that are dirty (and rename it to kvm_test_clear_dirty_npages()
to emphasize that that's what it returns). In kvmppc_hv_get_dirty_log()
we then set that many bits in the dirty map.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Currently, when a huge page is faulted in for a guest, we select the
rmap chain to insert the HPTE into based on the guest physical address
that the guest tried to access. Since there is an rmap chain for each
system page, there are many rmap chains for the area covered by a huge
page (e.g. 256 for 16MB pages when PAGE_SIZE = 64kB), and the huge-page
HPTE could end up in any one of them.
For consistency, and to make the huge-page HPTEs easier to find, we now
put huge-page HPTEs in the rmap chain corresponding to the base address
of the huge page.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The global_invalidates() function contains a check that is intended
to tell whether we are currently executing in the context of a hypercall
issued by the guest. The reason is that the optimization of using a
local TLB invalidate instruction is only valid in that context. The
check was testing local_paca->kvm_hstate.kvm_vcore, which gets set
when entering the guest but no longer gets cleared when exiting the
guest. To fix this, we use the kvm_vcpu field instead, which does
get cleared when exiting the guest, by the kvmppc_release_hwthread()
calls inside kvmppc_run_core().
The effect of having the check wrong was that when kvmppc_do_h_remove()
got called from htab_write() on the destination machine during a
migration, it cleared the current cpu's bit in kvm->arch.need_tlb_flush.
This meant that when the guest started running in the destination VM,
it may miss out on doing a complete TLB flush, and therefore may end
up using stale TLB entries from a previous guest that used the same
LPID value.
This should make migration more reliable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Commit b005255e12a3 ("KVM: PPC: Book3S HV: Context-switch new POWER8
SPRs") added a definition of KVM_REG_PPC_WORT with the same register
number as the existing KVM_REG_PPC_VRSAVE (though in fact the
definitions are not identical because of the different register sizes.)
For clarity, this moves KVM_REG_PPC_WORT to the next unused number,
and also adds it to api.txt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We worked around some nasty KVM magic page hcall breakages:
1) NX bit not honored, so ignore NX when we detect it
2) LE guests swizzle hypercall instruction
Without these fixes in place, there's no way it would make sense to expose kvm
hypercalls to a guest. Chances are immensely high it would trip over and break.
So add a new CAP that gives user space a hint that we have workarounds for the
bugs above in place. It can use those as hint to disable PV hypercalls when
the guest CPU is anything POWER7 or higher and the host does not have fixes
in place.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
When we reset the in-kernel MPIC controller, we forget to reset some hidden
state such as destmask and output. This state is usually set when the guest
writes to the IDR register for a specific IRQ line.
To make sure we stay in sync and don't forget hidden state, treat reset of
the IDR register as a simple write of the IDR register. That automatically
updates all the hidden state as well.
Reported-by: Paul Janzen <pcj@pauljanzen.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
There are LE Linux guests out there that don't handle hypercalls correctly.
Instead of interpreting the instruction stream from device tree as big endian
they assume it's a little endian instruction stream and fail.
When we see an illegal instruction from such a byte reversed instruction stream,
bail out graciously and just declare every hcall as error.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We get an array of instructions from the hypervisor via device tree that
we write into a buffer that gets executed whenever we want to make an
ePAPR compliant hypercall.
However, the hypervisor passes us these instructions in BE order which
we have to manually convert to LE when we want to run them in LE mode.
With this fixup in place, I can successfully run LE kernels with KVM
PV enabled on PR KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Use make_dsisr instead of open coding it. This also have
the added benefit of handling alignment interrupt on additional
instructions.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Although it's optional, IBM POWER cpus always had DAR value set on
alignment interrupt. So don't try to compute these values.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Because old kernels enable the magic page and then choke on NXed trampoline
code we have to disable NX by default in KVM when we use the magic page.
However, since commit b18db0b8 we have successfully fixed that and can now
leave NX enabled, so tell the hypervisor about this.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Old guests try to use the magic page, but map their trampoline code inside
of an NX region.
Since we can't fix those old kernels, try to detect whether the guest is sane
or not. If not, just disable NX functionality in KVM so that old guests at
least work at all. For newer guests, add a bit that we can set to keep NX
functionality available.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
On recent IBM Power CPUs, while the hashed page table is looked up using
the page size from the segmentation hardware (i.e. the SLB), it is
possible to have the HPT entry indicate a larger page size. Thus for
example it is possible to put a 16MB page in a 64kB segment, but since
the hash lookup is done using a 64kB page size, it may be necessary to
put multiple entries in the HPT for a single 16MB page. This
capability is called mixed page-size segment (MPSS). With MPSS,
there are two relevant page sizes: the base page size, which is the
size used in searching the HPT, and the actual page size, which is the
size indicated in the HPT entry. [ Note that the actual page size is
always >= base page size ].
We use "ibm,segment-page-sizes" device tree node to advertise
the MPSS support to PAPR guest. The penc encoding indicates whether
we support a specific combination of base page size and actual
page size in the same segment. We also use the penc value in the
LP encoding of HPTE entry.
This patch exposes MPSS support to KVM guest by advertising the
feature via "ibm,segment-page-sizes". It also adds the necessary changes
to decode the base page size and the actual page size correctly from the
HPTE entry.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Today when KVM tries to reserve memory for the hash page table it
allocates from the normal page allocator first. If that fails it
falls back to CMA's reserved region. One of the side effects of
this is that we could end up exhausting the page allocator and
get linux into OOM conditions while we still have plenty of space
available in CMA.
This patch addresses this issue by first trying hash page table
allocation from CMA's reserved region before falling back to the normal
page allocator. So if we run out of memory, we really are out of memory.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
POWER8 introduces transactional memory which brings along a number of new
registers and MSR bits.
Implementing all of those is a pretty big headache, so for now let's at least
emulate enough to make Linux's context switching code happy.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
POWER8 introduces a new facility called the "Event Based Branch" facility.
It contains of a few registers that indicate where a guest should branch to
when a defined event occurs and it's in PR mode.
We don't want to really enable EBB as it will create a big mess with !PR guest
mode while hardware is in PR and we don't really emulate the PMU anyway.
So instead, let's just leave it at emulation of all its registers.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
POWER8 implements a new register called TAR. This register has to be
enabled in FSCR and then from KVM's point of view is mere storage.
This patch enables the guest to use TAR.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
POWER8 introduced a new interrupt type called "Facility unavailable interrupt"
which contains its status message in a new register called FSCR.
Handle these exits and try to emulate instructions for unhandled facilities.
Follow-on patches enable KVM to expose specific facilities into the guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
In parallel to the Processor ID Register (PIR) threaded POWER8 also adds a
Thread ID Register (TIR). Since PR KVM doesn't emulate more than one thread
per core, we can just always expose 0 here.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
When we expose a POWER8 CPU into the guest, it will start accessing PMU SPRs
that we don't emulate. Just ignore accesses to them.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
With the previous patches applied, we can now successfully use PR KVM on
little endian hosts which means we can now allow users to select it.
However, HV KVM still needs some work, so let's keep the kconfig conflict
on that one.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
When the host CPU we're running on doesn't support dcbz32 itself, but the
guest wants to have dcbz only clear 32 bytes of data, we loop through every
executable mapped page to search for dcbz instructions and patch them with
a special privileged instruction that we emulate as dcbz32.
The only guests that want to see dcbz act as 32byte are book3s_32 guests, so
we don't have to worry about little endian instruction ordering. So let's
just always search for big endian dcbz instructions, also when we're on a
little endian host.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The shared (magic) page is a data structure that contains often used
supervisor privileged SPRs accessible via memory to the user to reduce
the number of exits we have to take to read/write them.
When we actually share this structure with the guest we have to maintain
it in guest endianness, because some of the patch tricks only work with
native endian load/store operations.
Since we only share the structure with either host or guest in little
endian on book3s_64 pr mode, we don't have to worry about booke or book3s hv.
For booke, the shared struct stays big endian. For book3s_64 hv we maintain
the struct in host native endian, since it never gets shared with the guest.
For book3s_64 pr we introduce a variable that tells us which endianness the
shared struct is in and route every access to it through helper inline
functions that evaluate this variable.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We expose a blob of hypercall instructions to user space that it gives to
the guest via device tree again. That blob should contain a stream of
instructions necessary to do a hypercall in big endian, as it just gets
passed into the guest and old guests use them straight away.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
When the guest does an RTAS hypercall it keeps all RTAS variables inside a
big endian data structure.
To make sure we don't have to bother about endianness inside the actual RTAS
handlers, let's just convert the whole structure to host endian before we
call our RTAS handlers and back to big endian when we return to the guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The HTAB on PPC is always in big endian. When we access it via hypercalls
on behalf of the guest and we're running on a little endian host, we need
to make sure we swap the bits accordingly.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The default MSR when user space does not define anything should be identical
on little and big endian hosts, so remove MSR_LE from it.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The "shadow SLB" in the PACA is shared with the hypervisor, so it has to
be big endian. We access the shadow SLB during world switch, so let's make
sure we access it in big endian even when we're on a little endian host.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The HTAB is always big endian. We access the guest's HTAB using
copy_from/to_user, but don't yet take care of the fact that we might
be running on an LE host.
Wrap all accesses to the guest HTAB with big endian accessors.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The HTAB is always big endian. We access the guest's HTAB using
copy_from/to_user, but don't yet take care of the fact that we might
be running on an LE host.
Wrap all accesses to the guest HTAB with big endian accessors.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Commit 9308ab8e2d made C/R HTAB updates go byte-wise into the target HTAB.
However, it didn't update the guest's copy of the HTAB, but instead the
host local copy of it.
Write to the guest's HTAB instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
CC: Paul Mackerras <paulus@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
|
|
With debug option "sleep inside atomic section checking" enabled we get
the below WARN_ON during a PR KVM boot. This is because upstream now
have PREEMPT_COUNT enabled even if we have preempt disabled. Fix the
warning by adding preempt_disable/enable around floating point and altivec
enable.
WARNING: at arch/powerpc/kernel/process.c:156
Modules linked in: kvm_pr kvm
CPU: 1 PID: 3990 Comm: qemu-system-ppc Tainted: G W 3.15.0-rc1+ #4
task: c0000000eb85b3a0 ti: c0000000ec59c000 task.ti: c0000000ec59c000
NIP: c000000000015c84 LR: d000000003334644 CTR: c000000000015c00
REGS: c0000000ec59f140 TRAP: 0700 Tainted: G W (3.15.0-rc1+)
MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI> CR: 42000024 XER: 20000000
CFAR: c000000000015c24 SOFTE: 1
GPR00: d000000003334644 c0000000ec59f3c0 c000000000e2fa40 c0000000e2f80000
GPR04: 0000000000000800 0000000000002000 0000000000000001 8000000000000000
GPR08: 0000000000000001 0000000000000001 0000000000002000 c000000000015c00
GPR12: d00000000333da18 c00000000fb80900 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 00003fffce4e0fa1
GPR20: 0000000000000010 0000000000000001 0000000000000002 00000000100b9a38
GPR24: 0000000000000002 0000000000000000 0000000000000000 0000000000000013
GPR28: 0000000000000000 c0000000eb85b3a0 0000000000002000 c0000000e2f80000
NIP [c000000000015c84] .enable_kernel_fp+0x84/0x90
LR [d000000003334644] .kvmppc_handle_ext+0x134/0x190 [kvm_pr]
Call Trace:
[c0000000ec59f3c0] [0000000000000010] 0x10 (unreliable)
[c0000000ec59f430] [d000000003334644] .kvmppc_handle_ext+0x134/0x190 [kvm_pr]
[c0000000ec59f4c0] [d00000000324b380] .kvmppc_set_msr+0x30/0x50 [kvm]
[c0000000ec59f530] [d000000003337cac] .kvmppc_core_emulate_op_pr+0x16c/0x5e0 [kvm_pr]
[c0000000ec59f5f0] [d00000000324a944] .kvmppc_emulate_instruction+0x284/0xa80 [kvm]
[c0000000ec59f6c0] [d000000003336888] .kvmppc_handle_exit_pr+0x488/0xb70 [kvm_pr]
[c0000000ec59f790] [d000000003338d34] kvm_start_lightweight+0xcc/0xdc [kvm_pr]
[c0000000ec59f960] [d000000003336288] .kvmppc_vcpu_run_pr+0xc8/0x190 [kvm_pr]
[c0000000ec59f9f0] [d00000000324c880] .kvmppc_vcpu_run+0x30/0x50 [kvm]
[c0000000ec59fa60] [d000000003249e74] .kvm_arch_vcpu_ioctl_run+0x54/0x1b0 [kvm]
[c0000000ec59faf0] [d000000003244948] .kvm_vcpu_ioctl+0x478/0x760 [kvm]
[c0000000ec59fcb0] [c000000000224e34] .do_vfs_ioctl+0x4d4/0x790
[c0000000ec59fd90] [c000000000225148] .SyS_ioctl+0x58/0xb0
[c0000000ec59fe30] [c00000000000a1e4] syscall_exit+0x0/0x98
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch make sure we inherit the LE bit correctly in different case
so that we can run Little Endian distro in PR mode
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The dcbtls instruction is able to lock data inside the L1 cache.
We don't want to give the guest actual access to hardware cache locks,
as that could influence other VMs on the same system. But we can tell
the guest that its locking attempt failed.
By implementing the instruction we at least don't give the guest a
program exception which it definitely does not expect.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The L1 instruction cache control register contains bits that indicate
that we're still handling a request. Mask those out when we set the SPR
so that a read doesn't assume we're still doing something.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Remove extra semicolon in kvm_arch_vcpu_dump_regs().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The kfree() function already NULL checks the parameter so remove the
redundant NULL checks before kfree() calls in arch/mips/kvm/.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The logging from MIPS KVM is fairly noisy with kvm_info() in places
where it shouldn't be, such as on VM creation and migration to a
different CPU. Replace these kvm_info() calls with kvm_debug().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm_debug() uses pr_debug() which is already compiled out in the absence
of a DEBUG define, so remove the unnecessary ifdef DEBUG lines around
kvm_debug() calls which are littered around arch/mips/kvm/.
As well as generally cleaning up, this prevents future bit-rot due to
DEBUG not being commonly used.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Fix build errors when DEBUG is defined in arch/mips/kvm/.
- The DEBUG code in kvm_mips_handle_tlbmod() was missing some variables.
- The DEBUG code in kvm_mips_host_tlb_write() was conditional on an
undefined "debug" variable.
- The DEBUG code in kvm_mips_host_tlb_inv() accessed asid_map directly
rather than using kvm_mips_get_user_asid(). Also fixed brace
placement.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Fix whitespace in struct kvm_mips_callbacks function pointers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The kvm_mips_comparecount_func() and kvm_mips_comparecount_wakeup()
functions are only used within arch/mips/kvm/kvm_mips.c, so make them
static.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Expose the KVM guest CP0_Count frequency to userland via a new
KVM_REG_MIPS_COUNT_HZ register accessible with the KVM_{GET,SET}_ONE_REG
ioctls.
When the frequency is altered the bias is adjusted such that the guest
CP0_Count doesn't jump discontinuously or lose any timer interrupts.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Expose two new virtual registers to userland via the
KVM_{GET,SET}_ONE_REG ioctls.
KVM_REG_MIPS_COUNT_CTL is for timer configuration fields and just
contains a master disable count bit. This can be used by userland to
freeze the timer in order to read a consistent state from the timer
count value and timer interrupt pending bit. This cannot be done with
the CP0_Cause.DC bit because the timer interrupt pending bit (TI) is
also in CP0_Cause so it would be impossible to stop the timer without
also risking a race with an hrtimer interrupt and having to explicitly
check whether an interrupt should have occurred.
When the timer is re-enabled it resumes without losing time, i.e. the
CP0_Count value jumps to what it would have been had the timer not been
disabled, which would also be impossible to do from userland with
CP0_Cause.DC. The timer interrupt also cannot be lost, i.e. if a timer
interrupt would have occurred had the timer not been disabled it is
queued when the timer is re-enabled.
This works by storing the nanosecond monotonic time when the master
disable is set, and using it for various operations instead of the
current monotonic time (e.g. when recalculating the bias when the
CP0_Count is set), until the master disable is cleared again, i.e. the
timer state is read/written as it would have been at that time. This
state is exposed to userland via the read-only KVM_REG_MIPS_COUNT_RESUME
virtual register so that userland can determine the exact time the
master disable took effect.
This should allow userland to atomically save the state of the timer,
and later restore it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|