| Age | Commit message (Collapse) | Author |
|---|
|
SYSENTER can cause a NT to be set which might cause crashes on the IRET
in the next task.
Following similar i386 patch from Linus.
Backport to 2.6.16 by Chuck Ebbert <76306.1226@compuserve.com>
[Changed 'set_debugreg' to the older 'set_debug' in setup64.c
and added raw_local_save_flags() from 2.6.19 to system.h]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
On the Core2 cpus, the rdtsc instruction is not serializing (as defined
in the architecture reference since rdtsc exists) and due to the deep
speculation of these cores, it's possible that you can observe time go
backwards between cores due to this speculation. Since the kernel
already deals with this with the SYNC_RDTSC flag, the solution is
simple, only assume that the instruction is serializing on family 15...
The price one pays for this is a slightly slower gettimeofday (by a
dozen or two cycles), but that increase is quite small to pay for a
really-going-forward tsc counter.
Backport by Chris Wright.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=5653
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Memory hotplug code of i386 adds memory to only highmem. So, if
CONFIG_HIGHMEM is not set, CONFIG_MEMORY_HOTPLUG shouldn't be set.
Otherwise, it causes compile error.
In addition, many architecture can't use memory hotplug feature yet. So, I
introduce CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This fixes a regression from the earlier DOS fix for non canonical
IRET addresses. It broke UML.
int_ret_from_syscall already does syscall exit tracing, so
no need to do it again in the caller.
This caused problems for UML and some other special programs doing
syscall interception.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
o Start booting into the capture kernel after an Oops if system is in a
unrecoverable state. System will boot into the capture kernel, if one is
pre-loaded by the user, and capture the kernel core dump.
o One of the following conditions should be true to trigger the booting of
capture kernel.
- panic_on_oops is set.
- pid of current thread is 0
- pid of current thread is 1
- Oops happened inside interrupt context.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
We do this by removing a micro-optimization that tries to avoid grabbing
the iommu_bitmap_lock spinlock and using a bus-locked operation.
This still races with other simultaneous alloc_iommu or free_iommu(size
> 1) which both use bus-unlocked operations.
The end result of this race is eventually ending
up with an iommu_gart_bitmap that has bits errornously set all over,
making large contiguous iommu space allocations fail with 'PCI-DMA:
Out of IOMMU space'.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
pages
This quietens warnings and actually fixes a bug. The unwind tables would
come out wrong without -32, causing pthread cancellation during them
to crash in the gcc runtime.
The problem seems to only happen with newer binutils
(it doesn't happen with 2.16.91.0.2 but happens wit 2.16.91.0.5)
Thanks to Brian Baker @ HP for test case and initial analysis.
Cc: brian.b@hp.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
AMD K7/K8 CPUs only save/restore the FOP/FIP/FDP x87 registers in FXSAVE
when an exception is pending. This means the value leak through context
switches and allow processes to observe some x87 instruction state of
other processes.
This was actually documented by AMD, but nobody recognized it as being
different from Intel before.
The fix first adds an optimization: instead of unconditionally calling
FNCLEX after each FXSAVE test if ES is pending and skip it when not
needed. Then do a x87 load from a kernel variable to clear FOP/FIP/FDP.
This means other processes always will only see a constant value defined
by the kernel in their FP state.
I took some pain to make sure to chose a variable that's already in L1
during context switch to make the overhead of this low.
Also alternative() is used to patch away the new code on CPUs who don't
need it.
Patch for both i386/x86-64.
The problem was discovered originally by Jan Beulich. Richard Brunner
provided the basic code for the workarounds, with contribution from Jan.
This is CVE-2006-1056
Cc: richard.brunner@amd.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
(CVE-2006-0744)
Intel EM64T CPUs handle uncanonical return addresses differently from
AMD CPUs.
The exception is reported in the SYSRET, not the next instruction.
Thgis leads to the kernel exception handler running on the user stack
with the wrong GS because the kernel didn't expect exceptions on this
instruction.
This version of the patch has the teething problems that plagued an
earlier version fixed.
This is CVE-2006-0744
Thanks to Ernie Petrides and Asit B. Mallick for analysis and initial
patches.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Just call IRET always, no need for any special cases.
Needed for the next bug fix.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This reverts commit c33d4568aca9028a22857f94f5e0850012b6444b.
Andrew Clayton and Hugh Dickins report that it's broken for them and
causes strange page table and slab corruption, and spontaneous reboots.
Let's get it right next time.
Cc: Andrew Clayton <andrew@rootshell.co.uk>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
EM64T CPUs have somewhat weird error reporting for non canonical RIPs in
SYSRET.
We can't handle any exceptions there because the exception handler would
end up running on the user stack which is unsafe.
To avoid problems any code that might end up with a user touched pt_regs
should return using int_ret_from_syscall. int_ret_from_syscall ends up
using IRET, which allows safe exceptions.
Cc: Ernie Petrides <petrides@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
While testing kexec and kdump we hit problems where the new kernel would
freeze or instantly reboot. The easiest way to trigger it was to kexec a
kernel compiled for CONFIG_M586 on an athlon cpu. Compiling for CONFIG_MK7
instead would work fine.
The patch fixes a few problems with the kexec inline asm.
Signed-off-by: Chris Mason <mason@suse.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
TSC assumption on IBM systems"
This reverts commit 13a229abc25640813f1480c0478dfc6bdbc1c19e.
Quoth Andi:
"After some consideration and feedback from various people it turns
out this wasn't that good an idea. It has some problems and needs
more work. Since it was only an optimization anyways it's best to
just back it out again for now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Commit 9ec4b1f356b3bad928ae8e2aa9caebfa737d52df made kprobes not compile
without module support, so just make that clear in the Kconfig file.
Also, since it's marked EXPERIMENTAL, make that dependency explicit too.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The commit e2c0388866dc12bef56b178b958f9b778fe6c687 added
setup_additional_cpus to setup.c but this is only defined if
CONFIG_HOTPLUG_CPU is set. This patch changes the #ifdef to reflect that.
Signed-off-by: Brian Magnuson <magnuson@rcn.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The previous experiment for using apicmaintimer on ATI systems didn't
work out very well. In particular laptops with C2/C3 support often
don't let it tick during idle, which makes it useless. There were also
some other bugs that made the apicmaintimer often not used at all.
I tried some other experiments - running timer over RTC and some other
things but they didn't really work well neither.
I rechecked the specs now and it turns out this simple change is
actually enough to avoid the double ticks on the ATI systems. We just
turn off IRQ 0 in the 8254 and only route it directly using the IO-APIC.
I tested it on a few ATI systems and it worked there. In fact it worked
on all chipsets (NVidia, Intel, AMD, ATI) I tried it on.
According to the ACPI spec routing should always work through the
IO-APIC so I think it's the correct thing to do anyways (and most of the
old gunk in check_timer should be thrown away for x86-64).
But for 2.6.16 it's best to do a fairly minimal change:
- Use the known to be working everywhere-but-ATI IRQ0 both over 8254
and IO-APIC setup everywhere
- Except on ATI disable IRQ0 in the 8254
- Remove the code to select apicmaintimer on ATI chipsets
- Add some boot options to allow to override this (just paranoia)
In 2.6.17 I hope to switch the default over to this for everybody.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
SMP time selection originally ran after all CPUs were brought up because
it needed to know the number of CPUs to decide if it needs an MP safe
timer or not.
This is not needed anymore because we know present CPUs early.
This fixes a couple of problems:
- apicmaintimer didn't always work because it relied on state that was
set up time_init_gtod too late.
- The output for the used timer in early kernel log was misleading
because time_init_gtod could actually change it later. Now always
print the final timer choice
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It didn't set up the CPU possible map early enough, so the
option didn't actually work.
Noticed by Heiko Carstens
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
[description from AK]
Old check for the IO-APIC watchdog during the timer check was wrong -
it obviously should only drop into this if the IO-APIC watchdog is used.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This makes x86-64 use the common X86_PM_TIMER Kconfig entry in drivers/acpi
And since PM timer is needed for correct timing on a lot of systems
now (e.g. AMD dual cores) and we often get bug reports from people
who forgot to set it make it depend on CONFIG_EMBEDDED. x86-64 had
this change before and it's a good thing.
I also fixed the description slightly to make this more clear.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
assumption on IBM systems
Big Unisys systems have multiple clusters too, but they have an
synchronized TSC.
I'm using the SMBIOS to check for vendor == IBM.
Cc: Chris McDermott <lcm@us.ibm.com>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In previous versions of pci-gart.c, no_iommu was used to determine if IOMMU was
disabled in the GART DMA mapping functions. This changed in 2.6.16 and now
gart_xxx() functions are only called if gart is enabled. Therefore, uses of
no_iommu in the GART code are no longer necessary and can be removed.
Also, it removes double deceleration of no_iommu and force_iommu in pci.h and
proto.h, by removing the deceleration in pci.h.
Lastly, end_pfn off by one error.
Tested (along with patch 1/2) on dual opteron with gart enabled, iommu=soft,
and iommu=off.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Commit 9c869edac591977314323a4eaad5f7633fca684f moved the i386 topology.c
file. That change broke x86-64 compiles, as it uses the same file.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Undo setting of CONFIG_DEBUG_INFO in the previous defconfig update. It
will make every build much slower and need more disk space and isn't a good
default.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Don't print KERN_INFO in the middle of a printk line.
printk(KERN_INFO "OEM ID: %s ",str);
is just above this. This is already fixed up in i386 copy.
Signed-off-by: Martin J. Bligh <mbligh@google.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Previously the numa hash code would be confused by holes in the node space
and stop early. This is the first part of the fix for the non boot issue
with empty nodes on Opterons.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Code was refusing good SRATs because about 12K got lost somewhere.
Allow less than 1MB of difference before rejecting it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
But do it after everything else to risk less from recursive
crashes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Otherwise it has no effect anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
has C2 or C3
Many laptops have problems with ticking the local APIC timer in C2/C3.
The code added earlier to use it by default on ATI didn't really work
for them. Don't enable it when the system supports C2/C3.
This doesn't fix the problem fully, but at least it's not worse than before.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This caused a sigreturn with bad argument on a preemptible kernel
to complain with
Debug: sleeping function called from invalid context at /home/lsrc/quilt/linux/include/linux/rwsem.h:43
in_atomic():0, irqs_disabled():1
Call Trace: {__might_sleep+190} {profile_task_exit+21}
{__do_exit+34} {do_wait+0}
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
data
Along with that, also suppress the memory touching altogether when the
watchdog is not running, to eliminate needless crosstalk. Plus ad a call
to it to make things consistent (one could also consider removing the call
in enable_timer_nmi_watchdog()).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
... and enable 1394 by default.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The early initialization of cpu_to_node code as it is now only updates the
cpu_to_node array, and does not update cpu_pda()->nodemember. This will
cause numa_node_id() to return 0 on systems where CPU 0 is not on Node 0.
This leads to a kernel panic in slab.c.
I've tested the patch below on a 16 processor x86_64 ES7000-600 server, and
no longer see the panic I saw with the original 2.6.16-rc3.
Signed-off-by: Dan Yeisley <dan.yeisley@unisys.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Don't touch the non DMA members in the sg list in dma_map_sg in the IOMMU
Some drivers (in particular ST) ran into problems because they reused the sg
lists after passing them to pci_map_sg(). The merging procedure in the K8
GART IOMMU corrupted the state. This patch changes it to only touch the dma*
entries during merging, but not the other fields. Approach suggested by Dave
Miller.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We found a problem with x86_64 kernels with preemption enabled, where
having multiple tasks doing ptrace singlesteps around the same time will
cause the system to 'oops'. The problem seems that a task can get
preempted out of the do_debug() processing while it is running on the
DEBUG_STACK stack. If another task on that same cpu then enters do_debug()
and uses the same per-cpu DEBUG_STACK stack, the previous preempted tasks's
stack contents can be corrupted, and the system will oops when the
preempted task is context switched back in again.
The typical oops looks like the following:
Unable to handle kernel paging request at ffffffffffffffae RIP: <ffffffff805452a1>{thread_return+34}
PGD 103027 PUD 102429067 PMD 0
Oops: 0002 [1] PREEMPT SMP
CPU 0
Modules linked in:
Pid: 3786, comm: ssdd Not tainted 2.6.15.2 #1
RIP: 0010:[<ffffffff805452a1>] <ffffffff805452a1>{thread_return+34}
RSP: 0018:ffffffff80824058 EFLAGS: 000136c2
RAX: ffff81017e12cea0 RBX: 0000000000000000 RCX: 00000000c0000100
RDX: 0000000000000000 RSI: ffff8100f7856e20 RDI: ffff81017e12cea0
RBP: 0000000000000046 R08: ffff8100f68a6000 R09: 0000000000000000
R10: 0000000000000000 R11: ffff81017e12cea0 R12: ffff81000c2d53e8
R13: ffff81017f5b3be8 R14: ffff81000c0036e0 R15: 000001056cbfc899
FS: 00002aaaaaad9b00(0000) GS:ffffffff80883800(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffffffffffffae CR3: 00000000f6fcf000 CR4: 00000000000006e0
Process ssdd (pid: 3786, threadinfo ffff8100f68a6000, task ffff8100f7856e20)
Stack: ffffffff808240d8 ffffffff8012a84a ffff8100055f6c00 0000000000000020
0000000000000001 ffff81000c0036e0 ffffffff808240b8 0000000000000000
0000000000000000 0000000000000000
Call Trace: <#DB>
<ffffffff8012a84a>{try_to_wake_up+985}
<ffffffff8012c0d3>{kick_process+87}
<ffffffff8013b262>{signal_wake_up+48}
<ffffffff8013b5ce>{specific_send_sig_info+179}
<ffffffff80546abc>{_spin_unlock_irqrestore+27}
<ffffffff8013b67c>{force_sig_info+159}
<ffffffff801103a0>{do_debug+289} <ffffffff80110278>{sync_regs+103}
<ffffffff8010ed9a>{paranoid_userspace+35}
Unable to handle kernel paging request at 00007fffffb7d000 RIP: <ffffffff8010f2e4>{show_trace+465}
PGD f6f25067 PUD f6fcc067 PMD f6957067 PTE 0
Oops: 0000 [2] PREEMPT SMP
This patch disables preemptions for the task upon entry to do_debug(), before
interrupts are reenabled, and then disables preemption before exiting
do_debug(), after disabling interrupts. I've noticed that the task can be
preempted either at the end of an interrupt, or on the call to
force_sig_info() on the spin_unlock_irqrestore() processing. It might be
better to attempt to code a fix in entry.S around the code that calls
do_debug().
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
[description from AK]
The IBM Summit 3 chipset doesn't implement the HPET timer replacement
option. Since the current Linux code relies on it use a mixed mode with
both PIT for the interrupt and HPET counters for the time keeping. That
was already implemented, but didn't work properly because it was still
using the last interrupt offset in HPET. This resulted in x460 not
booting. Fix this up by using the free running HPET counter.
Shouldn't affect any other machine because they either use full HPET mode
or no HPET at all.
TBD needs a similar 32bit fix.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The *at patches introduced fstatat and, due to inusfficient research, I
used the newfstat functions generally as the guideline. The result is that
on 32-bit platforms we don't have all the information needed to implement
fstatat64.
This patch modifies the code to pass up 64-bit information if
__ARCH_WANT_STAT64 is defined. I renamed the syscall entry point to make
this clear. Other archs will continue to use the existing code. On x86-64
the compat code is implemented using a new sys32_ function. this is what
is done for the other stat syscalls as well.
This patch might break some other archs (those which define
__ARCH_WANT_STAT64 and which already wired up the syscall). Yet others
might need changes to accomodate the compatibility mode. I really don't
want to do that work because all this stat handling is a mess (more so in
glibc, but the kernel is also affected). It should be done by the arch
maintainers. I'll provide some stand-alone test shortly. Those who are
eager could compile glibc and run 'make check' (no installation needed).
The patch below has been tested on x86 and x86-64.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add unshare syscall for x86-64
ppoll/pselect are not ready yet, but add reservations.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
drive_info is used only by hd.c and that happens under #ifdef __i386__.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Currently, x86_64 and ia64 arches do not clear the corresponding bits in
the node's cpumask when a cpu goes down or cpu bring up is cancelled. This
is buggy since there are pieces of common code where the cpumask is checked
in the cpu down code path to decide on things (like in the slab down path).
PPC does the right thing, but x86_64 and ia64 don't (This was the reason
Sonny hit upon a slab bug during cpu offline on ppc and could not reproduce
on other arches). This patch fixes it for x86_64. I won't attempt ia64 as
I cannot test it.
Credit for spotting this should go to Alok.
(akpm: this was applied, then reverted. But it's OK now because we now use
for_each_cpu() in the right places).
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This reverts commit 10f4dc8b27ac42f930ac55adb8c521264dc997f8.
Quoth Andi Kleen:
"Kiran decided that it makes the problem worse than it was before.
Fixing it fully requires more work which is too much for 2.6.16. So
please revert that commit for now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch contains a printk reorder to remove the current problem of
displaying "PCI-DMA: Disabling IOMMU." and then "PCI-DMA: using GART
IOMMU" 20 lines later in dmesg.
It also constains a printk reorder in swiotlb to state swiotlb
enablement prior to describing the location of the bounce buffers, and a
printk reorder to state gart enablement prior to describing the
aperature.
Also constains a whitespace cleanup in arch/x86_64/kernel/setup.c
Tested (along with patch 2/2) on dual opteron with gart enabled,
iommu=soft, and iommu=off.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Hack for 2.6.16. In 2.6.17 all code that uses NR_CPUs should
be audited and changed to only touch possible CPUs.
Don't mark the reference per cpu data init data (so it stays
around after boot) and point all impossible CPUs to it. This way
they reference some valid - although shared memory. Usually
this is only initialization like INIT_LIST_HEADs and there
won't be races because these CPUs never run. Still somewhat hackish.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
not enabled
It's bad juju to touch the APIC when it hasn't been enabled.
I also moved ack_bad_irq for x86-64 out of line following i386.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Checking of the validity of pointers should be consistently done before
dereferencing the pointer.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
