| Age | Commit message (Collapse) | Author |
|---|
|
commit 6a469e4665bc158599de55d64388861d0a9f10f4 upstream.
This is a workaround for a UV2 hub bug that affects the format of system
global addresses.
The GRU API for UV2 was inadvertently broken by a hardware change. The
format of the physical address used for TLB dropins and for addresses used
with instructions running in unmapped mode has changed. This change was
not documented and became apparent only when diags failed running on
system simulators.
For UV1, TLB and GRU instruction physical addresses are identical to
socket physical addresses (although high NASID bits must be OR'ed into the
address).
For UV2, socket physical addresses need to be converted. The NODE portion
of the physical address needs to be shifted so that the low bit is in bit
39 or bit 40, depending on an MMR value.
It is not yet clear if this bug will be fixed in a silicon respin. If it
is fixed, the hub revision will be incremented & the workaround disabled.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a3ea14df0e383f44dcb2e61badb71180dbffe526 upstream.
When executing EC commands, only waiting when there are still
more bytes to write is usually fine. However, if the system
suspends very quickly after a call to olpc_ec_cmd(), the last
data byte may not yet be transferred to the EC, and the command
will not complete.
This solves a bug where the SCI wakeup mask was not correctly
written when going into suspend.
It means that sometimes, on XO-1.5 (but not XO-1), the
devices that were marked as wakeup sources can't wake up
the system. e.g. you ask for wifi wakeups, suspend, but then
incoming wifi frames don't wake up the system as they should.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Testing suggests that at least some Lenovos and some Intels will
fail to reboot via EFI, attempting to jump to an unmapped
physical address. In the long run we could handle this by
providing a page table with a 1:1 mapping of physical addresses,
but for now it's probably just easier to assume that ACPI or
legacy methods will be present and reboot via those.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/1309985557-15350-1-git-send-email-mjg@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Commit 916f676f8dc started reserving boot service code since some systems
require you to keep that code around until SetVirtualAddressMap is called.
However, in some cases those areas will overlap with reserved regions.
The proper medium-term fix is to fix the bootloader to prevent the
conflicts from occurring by moving the kernel to a better position,
but the kernel should check for this possibility, and only reserve regions
which can be reserved.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Link: http://lkml.kernel.org/r/4DF7A005.1050407@gmail.com
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
UEFI stands for "Unified Extensible Firmware Interface", where "Firmware"
is an ancient African word meaning "Why do something right when you can
do it so wrong that children will weep and brave adults will cower before
you", and "UEI" is Celtic for "We missed DOS so we burned it into your
ROMs". The UEFI specification provides for runtime services (ie, another
way for the operating system to be forced to depend on the firmware) and
we rely on these for certain trivial tasks such as setting up the
bootloader. But some hardware fails to work if we attempt to use these
runtime services from physical mode, and so we have to switch into virtual
mode. So far so dreadful.
The specification makes it clear that the operating system is free to do
whatever it wants with boot services code after ExitBootServices() has been
called. SetVirtualAddressMap() can't be called until ExitBootServices() has
been. So, obviously, a whole bunch of EFI implementations call into boot
services code when we do that. Since we've been charmingly naive and
trusted that the specification may be somehow relevant to the real world,
we've already stuffed a picture of a penguin or something in that address
space. And just to make things more entertaining, we've also marked it
non-executable.
This patch allocates the boot services regions during EFI init and makes
sure that they're executable. Then, after SetVirtualAddressMap(), it
discards them and everyone lives happily ever after. Except for the ones
who have to work on EFI, who live sad lives haunted by the knowledge that
someone's eventually going to write yet another firmware specification.
[ hpa: adding this to urgent with a stable tag since it fixes currently-broken
hardware. However, I do not know what the dependencies are and so I do
not know which -stable versions this may be a candidate for. ]
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1306331593-28715-1-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@kernel.org>
|
|
SGI UV's uv_tlb.c driver has become rather hard to read, with overly large
functions, non-standard coding style and (way) too long variable, constant
and function names and non-obvious code flow sequences.
This patch improves the readability and maintainability of the driver
significantly, by doing the following strict code cleanups with no side
effects:
- Split long functions into shorter logical functions.
- Shortened some variable and structure member names.
- Added special functions for reads and writes of MMR regs with
very long names.
- Added the 'tunables' table to shortened tunables_write().
- Added the 'stat_description' table to shorten uv_ptc_proc_write().
- Pass fewer 'stat' arguments where it can be derived from the 'bcp'
argument.
- Function definitions consistent on one line, and inline in few (short) cases.
- Moved some small structures and an atomic inline function to the header file.
- Moved some local variables to the blocks where they are used.
- Updated the copyright date.
- Shortened uv_write_global_mmr64() etc. using some aliasing; no
line breaks. Renamed many uv_.. functions that are not exported.
- Aligned structure fields.
[ note that not all structures are aligned the same way though; I'd like
to keep the extensive commenting in some of them. ]
- Shortened some long structure names.
- Standard pass/fail exit from init_per_cpu()
- Vertical alignment for mass initializations.
- More separation between blocks of code.
Tested on a 16-processor Altix UV.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: penberg@kernel.org
Link: http://lkml.kernel.org/r/E1QOw12-0004MN-Lp@eag09.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch adds support for a new version of the SGI UV hub
chip. The hub chip is the node controller that connects multiple
blades into a larger coherent SSI.
For the most part, UV2 is compatible with UV1. The majority of
the changes are in the addresses of MMRs and in a few cases, the
contents of MMRs. These changes are the result in changes in the
system topology such as node configuration, processor types,
maximum nodes, physical address sizes, etc.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20110511175028.GA18006@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Introduce pci_map_biosrom()
x86, olpc: Use device tree for platform identification
|
|
'x86-irq-for-linus' and 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, efi: Ensure that the entirity of a region is mapped
x86, efi: Pass a minimal map to SetVirtualAddressMap()
x86, efi: Merge contiguous memory regions of the same type and attribute
x86, efi: Consolidate EFI nx control
x86, efi: Remove virtual-mode SetVirtualAddressMap call
* 'x86-gart-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, gart: Don't enforce GART aperture lower-bound by alignment
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Don't unmask disabled irqs when migrating them
x86: Skip migrating IRQF_PER_CPU irqs in fixup_irqs()
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mce: Drop the default decoding notifier
x86, MCE: Do not taint when handling correctable errors
|
|
'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, apic: Print verbose error interrupt reason on apic=debug
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Demacro CONFIG_PARAVIRT cpu accessors
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix mrst sparse complaints
x86: Fix spelling error in the memcpy() source code comment
x86, mpparse: Remove unnecessary variable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
|
|
master.kernel.org:~rmk/linux-2.6-arm into timers/clocksource
Conflicts:
arch/ia64/kernel/cyclone.c
arch/mips/kernel/i8253.c
arch/x86/kernel/i8253.c
Reason: Resolve conflicts so further cleanups do not conflict further
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This is a fix for the SGI Altix-UV Broadcast Assist Unit code,
which is used for TLB flushing.
Certain hardware configurations (that customers are ordering)
cause nasids (numa address space id's) to be non-consecutive.
Specifically, once you have more than 4 blades in a IRU
(Individual Rack Unit - or 1/2 rack) but less than the maximum
of 16, the nasid numbering becomes non-consecutive. This
currently results in a 'catastrophic error' (CATERR) detected by
the firmware during OS boot. The BAU is generating an 'INTD'
request that is targeting a non-existent nasid value. Such
configurations may also occur when a blade is configured off
because of hardware errors. (There is one UV hub per blade.)
This patch is required to support such configurations.
The problem with the tlb_uv.c code is that is using the
consecutive hub numbers as indices to the BAU distribution bit
map. These are simply the ordinal position of the hub or blade
within its partition. It should be using physical node numbers
(pnodes), which correspond to the physical nasid values. Use of
the hub number only works as long as the nasids in the partition
are consecutive and increase with a stride of 1.
This patch changes the index to be the pnode number, thus
allowing nasids to be non-consecutive.
It also provides a table in local memory for each cpu to
translate target cpu number to target pnode and nasid.
And it improves naming to properly reflect 'node' and 'uvhub'
versus 'nasid'.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1QJmxX-0002Mz-Fk@eag09.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
It's possible for init_memory_mapping() to fail to map the entire region
if it crosses a boundary, so ensure that we complete the mapping.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-5-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Experimentation with various EFI implementations has shown that functions
outside runtime services will still update their pointers if
SetVirtualAddressMap() is called with memory descriptors outside the
runtime area. This is obviously insane, and therefore is unsurprising.
Evidence from instrumenting another EFI implementation suggests that it
only passes the set of descriptors covering runtime regions, so let's
avoid any problems by doing the same. Runtime descriptors are copied to
a separate memory map, and only that map is passed back to the firmware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-4-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Some firmware implementations assume that physically contiguous regions
will be contiguous in virtual address space. This assumption is, obviously,
entirely unjustifiable. Said firmware implementations lack the good grace
to handle their failings in a measured and reasonable manner, instead
tending to shit all over address space and oopsing the kernel.
In an ideal universe these firmware implementations would simultaneously
catch fire and cease to be a problem, but since some of them are present
in attractively thin and shiny metal devices vanity wins out and some
poor developer spends an extended period of time surrounded by a
growing array of empty bottles until the underlying reason becomes
apparent. Said developer presents this patch, which simply merges
adjacent regions if they happen to be contiguous and have the same EFI
memory type and caching attributes.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-3-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The core EFI code and 64-bit EFI code currently have independent
implementations of code for setting memory regions as executable or not.
Let's consolidate them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-2-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The spec says that SetVirtualAddressMap doesn't work once you're in
virtual mode, so there's no point in having infrastructure for calling
it from there.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-1-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Fix these Sparse complaints:
CHECK arch/x86/platform/mrst/mrst.c
arch/x86/platform/mrst/mrst.c:197:13: warning: symbol 'mrst_time_init' was not declared. Should it be static?
arch/x86/platform/mrst/mrst.c:219:16: warning: symbol 'mrst_arch_setup' was not declared. Should it be static?
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Roman Gezikov <roman.gezikov@atheros.com>
Cc: Joonas Viskari <joonas.viskari@atheros.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Allen Kao <allen.kao@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Link: http://lkml.kernel.org/r/1304719209-26913-1-git-send-email-lrodriguez@atheros.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The USB and SATA ioapic interrrupt pins are configured as edge type,
but need to be level type interrupts to work correctly.
[ tglx: Split out from the combo patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Moorestown systems crash on boot because the secondary CPU
clockevent (apbt1) will fail to request irq#1, which does not
have ioapic chip in its irq_desc[] entry.
Background:
Moorestown platform does not have ISA bus nor legacy IRQs. It
reuses the range of legacy IRQs for regular device interrupts.
The routing information of early system device IRQs (timers) are
obtained from firmware provided SFI tables. We reuse/fake MP
configuration table to facilitate IRQ setup with IOAPIC.
Maintaining a 1:1 mapping of IOAPIC pin (RTE entry) and IRQ#
makes routing information clean and easy to understand on
Moorestown. Though optional.
This patch allows SFI timer and vRTC IRQ to be treated as ISA
IRQ so that pin2irq mapping will be 1:1.
Also fixed MP table type and use macros to clearly set MP IRQ
entries. As a result, apbt timer and RTC interrupts on
Moorestown are within legacy IRQ range:
# cat /proc/interrupts
CPU0 CPU1
0: 11249 0 IO-APIC-edge apbt0
1: 0 12271 IO-APIC-edge apbt1
8: 887 0 IO-APIC-fasteoi dw_spi
13: 0 0 IO-APIC-fasteoi INTEL_MID_DMAC2
14: 0 0 IO-APIC-fasteoi rtc0
Further discussion of this patch can be found at:
https://lkml.org/lkml/2010/6/10/70
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Link: http://lkml.kernel.org/r/1302286980-21139-1-git-send-email-jacob.jun.pan@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
without the reg property Ben's new code won't find the PCI & ISA
bridge and the devices won't get the DT-node attached.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: monstr@monstr.eu
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/20110407121315.GA9204@linutronix.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
'timers-fixes-for-linus', 'irq-fixes-for-linus' and 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
|
|
The sfi_mrtc_array[] only gets initialized when the sfi mrtc
table is parsed, so the vrtc_paddr should be initalized after it
too.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302140389-27603-1-git-send-email-feng.tang@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Reported-by: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Stop including <linux/delay.h> in x86 header files which don't
need it. This will let the compiler complain when this header is
not included by source files when it should, so that
contributors can fix the problem before building on other
architectures starts to fail.
Credits go to Geert for the idea.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20110325152014.297890ec@endymion.delvare>
[ this also fixes an upstream build bug in drivers/media/rc/ite-cir.c ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The cs5535-pms cell doesn't actually need to be cloned, so we can drop that
and simply have the olpc-xo1.c driver use "cs5535-pms" directly.
Also, rename the cs5535-acpi clones to what we actually use for the (currently
out-of-tree) SCI driver. In the process, that fixes a subtle bug in
olpc-xo1.c which broke powerdown on XO-1s.. olpc-xo1-ac-acpi was a typo, not
something that actually existed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Replace mfd_shared_platform_driver_register with mfd_clone_cell. The
former was called by an mfd client, and registered both a platform driver
and device. The latter is called by an mfd driver, and registers only a
platform device.
The downside of this is that mfd drivers need to be modified whenever
new clients are added that share a cell; the upside is that it fits
Linux's driver model better. It's also simpler.
This also converts cs5535-mfd/olpc-xo1 from the old API. cs5535-mfd
now creates the olpc-xo1-{acpi,pms} devices, while olpc-xo1 binds to
them via platform drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
As requested by Samuel, there's not really any reason to have "shared"
in the name.
This also modifies the only user of the function, as well.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This enables sharing of cs5535-mfd cells via the new mfd_shared_* API.
Hooks for enable/disble of resources are added, with refcounting of
resources being automatically handled so that cs5535_mfd_res_enable/disable
are only called when necessary.
Clients of cs5535-mfd (in this case, olpc-xo1.c) are also modified to
use the mfd_shared API. The platform drivers are also renamed to
olpc-xo1-{pms,acpi}, and resource enabling/disabling is replaced
with mfd_shared API calls.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (116 commits)
x86: Enable forced interrupt threading support
x86: Mark low level interrupts IRQF_NO_THREAD
x86: Use generic show_interrupts
x86: ioapic: Avoid redundant lookup of irq_cfg
x86: ioapic: Use new move_irq functions
x86: Use the proper accessors in fixup_irqs()
x86: ioapic: Use irq_data->state
x86: ioapic: Simplify irq chip and handler setup
x86: Cleanup the genirq name space
genirq: Add chip flag to force mask on suspend
genirq: Add desc->irq_data accessor
genirq: Add comments to Kconfig switches
genirq: Fixup fasteoi handler for oneshot mode
genirq: Provide forced interrupt threading
sched: Switch wait_task_inactive to schedule_hrtimeout()
genirq: Add IRQF_NO_THREAD
genirq: Allow shared oneshot interrupts
genirq: Prepare the handling of shared oneshot interrupts
genirq: Make warning in handle_percpu_event useful
x86: ioapic: Move trigger defines to io_apic.h
...
Fix up trivial(?) conflicts in arch/x86/pci/xen.c due to genirq name
space changes clashing with the Xen cleanups. The set_irq_msi() had
moved to xen_bind_pirq_msi_to_irq().
|
|
Make OLPC fully depend on device tree, and use it to identify the OLPC
platform details. Some nodes are exposed as platform devices where we
plan to use device tree for device probing.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110313151017.C255F9D401E@zog.reactivated.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ce4100: Set pci ops via callback instead of module init
x86/mm: Fix pgd_lock deadlock
x86/mm: Handle mm_fault_error() in kernel space
x86: Don't check for BIOS corruption in first 64K when there's no need to
|
|
Setting the pci ops on subsys initcall unconditionally will break
multi platform kernels on anything except ce4100.
Use x86_init.pci.init ops to call this only on real ce4100 platforms.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: sodaville@linutronix.de
LKML-Reference: <20110314093340.GA21026@www.tglx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
These cannot be threaded.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
genirq is switching to a consistent name space for the irq related
functions. Convert x86. Conversion was done with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Initialize the broadcast assist unit base destination node id properly
x86, numa: Fix numa_emulation code with memory-less node0
x86, build: Make sure mkpiggy fails on read error
|
|
The BAU's initialization of the broadcast description header is
lacking the coherence domain (high bits) in the nasid. This
causes a catastrophic system failure when running on a system
with multiple coherence domains.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1PxKBB-0005F0-3U@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
..similar to what sparc's prom_early_alloc does.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Up to now we force enable the local apic in the devicetree setup
uncoditionally and set smp_found_config unconditionally to 1 when a
devicetree blob is available. This breaks, when local apic is disabled
in the Kconfig.
Make it consistent by initializing device tree explicitely before
smp_get_config() so a non lapic configuration could be used as well.
To be functional that would require to implement PIT as an interrupt
host, but the only user of this code until now is ce4100 which
requires apics to be available. So we leave this up to those who need
it.
Tested-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Use device tree information to setup IO_APIC configuration, interrupt
routing, HPET and everything else which cannot be enumerated by other
means.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-11-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
History:
v1..v2:
- dropped device_type except for cpu & pci. I have the compatible string
for pci so I can drop the device_type once it is possible
- I lowercased all compatible types. I will need to resend some patches
which have upper case intel
- The cpu had the same compatible string as the soc node. So I added to
the soc node -immr for internel memory mapped registers.
- I added generic names for all parts.
- I reworked the i2c bars matching the way you suggested. I added a
compatible node for the PCI device which only the PCI ids in its
compatible string. The bars (each represents a complete i2c
controller) have a "intel,ce4100-i2c-controller" compatible node. It
is not used by the driver.
The driver is probed via PCI ids (by the pci subsystem not OF) and
matches the bar address against the ressource in the child node. Once
there is a hit the node is attached.
- The SPI driver is also probed via pci. However I also attached a
compatible property based on PCI ids
v2..v3:
- intel,ce4100-immr become intel,ce4100-cp. cp stands for core
peripherals. The Atom data sheet talks here about ACPI devices. Since
we don't have ACPI this does not apply here.
- The interrupt map is gone. There are now plenty of device nodes.
- The "unit address string" got fixed, it uses not DD,V format.
v3..v4:
- added descriptions for compatible nodes introduced here:
- intel,ce4100-ioapic
- intel,ce4100-lapic
- intel,ce4100-hpet
- intel,ce4100
- intel,ce4100-cp
- intel,ce4100-pci
- added a description about I2C controller magic.
- Added gpio-controller and gpio-cells property to gpio devices. Those
properties are not (yet) used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-4-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
OLPC_OPENFIRMWARE_DT is just there to be selected by OLPC and selects
OF_PROMTREE. So let OLPC select OF_PROMTREE and remove that extra
config indirection. Fixup code and Makefile and use CONFIG_OF_PROMTREE
instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andres Salomon <dilinger@queued.net>
|
|
Neither CONFIG_OLPC_OPENFIRMWARE nor CONFIG_OLPC_OPENFIRMWARE_DT are
really necessary.
OLPC selects OLPC_OPENFIRMWARE unconditionally, so move the "select
OF" part under OLPC config option and fixup the dependencies in
Makefiles and code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andres Salomon <dilinger@queued.net>
|
|
into x86/platform
Reason: x86 devicetree support for ce4100 depends on those device tree
changes scheduled for .39.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This converts the remaining x86 clocksources to use
clocksource_register_hz/khz.
CC: jacob.jun.pan@intel.com
CC: Glauber Costa <glommer@redhat.com>
CC: Dimitri Sivanich <sivanich@sgi.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Jeremy Fitzhardinge <jeremy@xensource.com>
CC: Chris McDermott <lcm@us.ibm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
|
|
If we don't assign Moorestown specific wallclock init and ops function
the rtc/persisent clock code will use cmos rtc for access, this will
crash Moorestown in that the ioports are not present.
Also in vrtc driver, should avoid using cmos access to check UIP status.
[feng.tang@intel.com: use set_fixmap_offset_nocache() to simplify code]
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The cs5535-mfd driver now takes care of the PCI BAR handling; this
means the olpc-xo1 driver shouldn't be touching the PCI device at all.
This patch uses both cs5535-acpi and cs5535-pms platform devices rather
than a single platform device because the cs5535-mfd driver may be used
by other CS5535 platform-specific drivers; OLPC doesn't get to dictate
that ACPI and PMS will always be used together.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-olpc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, olpc: Speed up device tree creation during boot
x86, olpc: Add OLPC device-tree support
x86, of: Define irq functions to allow drivers/of/* to build on x86
|
