| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 1cef94c36bd4d79b5ae3a3df99ee0d76d6a4a6dc ]
This is the longest boot string that silo supports.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Cc: Bob Picco <bob.picco@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d195b71bad4347d2df51072a537f922546a904f1 ]
swapper_low_pmd_dir and swapper_pud_dir are actually completely
useless and unnecessary.
We just need swapper_pg_dir[]. Naturally the other page table chunks
will be allocated on an as-needed basis. Since the kernel actually
accesses these tables in the PAGE_OFFSET view, there is not even a TLB
locality advantage of placing them in the kernel image.
Use the hard coded vmlinux.ld.S slot for swapper_pg_dir which is
naturally page aligned.
Increase MAX_BANKS to 1024 in order to handle heavily fragmented
virtual guests.
Even with this MAX_BANKS increase, the kernel is 20K+ smaller.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ee6a9333fa58e11577c1b531b8e0f5ffc0fd6f50 ]
This patch attempts to do a few things. The highlights are: 1) enable
SPARSE_IRQ unconditionally, 2) kills off !SPARSE_IRQ code 3) allocates
ivector_table at boot time and 4) default to cookie only VIRQ mechanism
for supported firmware. The first firmware with cookie only support for
me appears on T5. You can optionally force the HV firmware to not cookie
only mode which is the sysino support.
The sysino is a deprecated HV mechanism according to the most recent
SPARC Virtual Machine Specification. HV_GRP_INTR is what controls the
cookie/sysino firmware versioning.
The history of this interface is:
1) Major version 1.0 only supported sysino based interrupt interfaces.
2) Major version 2.0 added cookie based VIRQs, however due to the fact
that OSs were using the VIRQs without negoatiating major version
2.0 (Linux and Solaris are both guilty), the VIRQs calls were
allowed even with major version 1.0
To complicate things even further, the VIRQ interfaces were only
actually hooked up in the hypervisor for LDC interrupt sources.
VIRQ calls on other device types would result in HV_EINVAL errors.
So effectively, major version 2.0 is unusable.
3) Major version 3.0 was created to signal use of VIRQs and the fact
that the hypervisor has these calls hooked up for all interrupt
sources, not just those for LDC devices.
A new boot option is provided should cookie only HV support have issues.
hvirq - this is the version for HV_GRP_INTR. This is related to HV API
versioning. The code attempts major=3 first by default. The option can
be used to override this default.
I've tested with SPARSE_IRQ on T5-8, M7-4 and T4-X and Jalap?no.
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bb4e6e85daa52a9f6210fa06a5ec6269598a202b ]
In order to accomodate embedded per-cpu allocation with large numbers
of cpus and numa nodes, we have to use as much virtual address space
as possible for the vmalloc region. Otherwise we can get things like:
PERCPU: max_distance=0x380001c10000 too large for vmalloc space 0xff00000000
So, once we select a value for PAGE_OFFSET, derive the size of the
vmalloc region based upon that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure, at compile time, that the kernel can properly support
whatever MAX_PHYS_ADDRESS_BITS is defined to.
On M7 chips, use a max_phys_bits value of 49.
Based upon a patch by Bob Picco.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c06240c7f5c39c83dfd7849c0770775562441b96 ]
For sparse memory configurations, the vmemmap array behaves terribly
and it takes up an inordinate amount of space in the BSS section of
the kernel image unconditionally.
Just build huge PMDs and look them up just like we do for TLB misses
in the vmalloc area.
Kernel BSS shrinks by about 2MB.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0dd5b7b09e13dae32869371e08e1048349fd040c ]
If max_phys_bits needs to be > 43 (f.e. for T4 chips), things like
DEBUG_PAGEALLOC stop working because the 3-level page tables only
can cover up to 43 bits.
Another problem is that when we increased MAX_PHYS_ADDRESS_BITS up to
47, several statically allocated tables became enormous.
Compounding this is that we will need to support up to 49 bits of
physical addressing for M7 chips.
The two tables in question are sparc64_valid_addr_bitmap and
kpte_linear_bitmap.
The first holds a bitmap, with 1 bit for each 4MB chunk of physical
memory, indicating whether that chunk actually exists in the machine
and is valid.
The second table is a set of 2-bit values which tell how large of a
mapping (4MB, 256MB, 2GB, 16GB, respectively) we can use at each 256MB
chunk of ram in the system.
These tables are huge and take up an enormous amount of the BSS
section of the sparc64 kernel image. Specifically, the
sparc64_valid_addr_bitmap is 4MB, and the kpte_linear_bitmap is 128K.
So let's solve the space wastage and the DEBUG_PAGEALLOC problem
at the same time, by using the kernel page tables (as designed) to
manage this information.
We have to keep using large mappings when DEBUG_PAGEALLOC is disabled,
and we do this by encoding huge PMDs and PUDs.
On a T4-2 with 256GB of ram the kernel page table takes up 16K with
DEBUG_PAGEALLOC disabled and 256MB with it enabled. Furthermore, this
memory is dynamically allocated at run time rather than coded
statically into the kernel image.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8c82dc0e883821c098c8b0b130ffebabf9aab5df ]
As currently coded the KTSB accesses in the kernel only support up to
47 bits of physical addressing.
Adjust the instruction and patching sequence in order to support
arbitrary 64 bits addresses.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4397bed080598001e88f612deb8b080bb1cc2322 ]
Now that we use 4-level page tables, we can provide up to 53-bits of
virtual address space to the user.
Adjust the VA hole based upon the capabilities of the cpu type probed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ac55c768143aa34cc3789c4820cbb0809a76fd9c ]
This has become necessary with chips that support more than 43-bits
of physical addressing.
Based almost entirely upon a patch by Bob Picco.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The T5 (niagara5) has different PCR related HV fast trap values and a new
HV API Group. This patch utilizes these and shares when possible with niagara4.
We use the same sparc_pmu niagara4_pmu. Should there be new effort to
obtain the MCU perf statistics then this would have to be changed.
Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add M6 and M7 chip type in cpumap.c to correctly build CPU distribution map that spans all online CPUs.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The following patch adds support for correctly
recognising M6 and M7 cpu type.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We changed PAGE_OFFSET to be a variable rather than a constant,
but this reference here in the hibernate assembler got missed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e2653143d7d79a49f1a961aeae1d82612838b12c ]
This breaks the stack end corruption detection facility.
What that facility does it write a magic value to "end_of_stack()"
and checking to see if it gets overwritten.
"end_of_stack()" is "task_thread_info(p) + 1", which for sparc64 is
the beginning of the FPU register save area.
So once the user uses the FPU, the magic value is overwritten and the
debug checks trigger.
Fix this by making the size explicit.
Due to the size we use for the fpsaved[], gsr[], and xfsr[] arrays we
are limited to 7 levels of FPU state saves. So each FPU register set
is 256 bytes, allocate 256 * 7 for the fpregs area.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f4da3628dc7c32a59d1fb7116bb042e6f436d611 ]
The AES loops in arch/sparc/crypto/aes_glue.c use a scheme where the
key material is preloaded into the FPU registers, and then we loop
over and over doing the crypt operation, reusing those pre-cooked key
registers.
There are intervening blkcipher*() calls between the crypt operation
calls. And those might perform memcpy() and thus also try to use the
FPU.
The sparc64 kernel FPU usage mechanism is designed to allow such
recursive uses, but with a catch.
There has to be a trap between the two FPU using threads of control.
The mechanism works by, when the FPU is already in use by the kernel,
allocating a slot for FPU saving at trap time. Then if, within the
trap handler, we try to use the FPU registers, the pre-trap FPU
register state is saved into the slot. Then at trap return time we
notice this and restore the pre-trap FPU state.
Over the long term there are various more involved ways we can make
this work, but for a quick fix let's take advantage of the fact that
the situation where this happens is very limited.
All sparc64 chips that support the crypto instructiosn also are using
the Niagara4 memcpy routine, and that routine only uses the FPU for
large copies where we can't get the source aligned properly to a
multiple of 8 bytes.
We look to see if the FPU is already in use in this context, and if so
we use the non-large copy path which only uses integer registers.
Furthermore, we also limit this special logic to when we are doing
kernel copy, rather than a user copy.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bdcf81b658ebc4c2640c3c2c55c8b31c601b6996 ]
Inconsistently, the raw_* IRQ routines do not interact with and update
the irqflags tracing and lockdep state, whereas the raw_* spinlock
interfaces do.
This causes problems in p1275_cmd_direct() because we disable hardirqs
by hand using raw_local_irq_restore() and then do a raw_spin_lock()
which triggers a lockdep trace because the CPU's hw IRQ state doesn't
match IRQ tracing's internal software copy of that state.
The CPU's irqs are disabled, yet current->hardirqs_enabled is true.
====================
reboot: Restarting system
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:3536 check_flags+0x7c/0x240()
DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled)
Modules linked in: openpromfs
CPU: 0 PID: 1 Comm: systemd-shutdow Tainted: G W 3.17.0-dirty #145
Call Trace:
[000000000045919c] warn_slowpath_common+0x5c/0xa0
[0000000000459210] warn_slowpath_fmt+0x30/0x40
[000000000048f41c] check_flags+0x7c/0x240
[0000000000493280] lock_acquire+0x20/0x1c0
[0000000000832b70] _raw_spin_lock+0x30/0x60
[000000000068f2fc] p1275_cmd_direct+0x1c/0x60
[000000000068ed28] prom_reboot+0x28/0x40
[000000000043610c] machine_restart+0x4c/0x80
[000000000047d2d4] kernel_restart+0x54/0x80
[000000000047d618] SyS_reboot+0x138/0x200
[00000000004060b4] linux_sparc_syscall32+0x34/0x60
---[ end trace 5c439fe81c05a100 ]---
possible reason: unannotated irqs-off.
irq event stamp: 2010267
hardirqs last enabled at (2010267): [<000000000049a358>] vprintk_emit+0x4b8/0x580
hardirqs last disabled at (2010266): [<0000000000499f08>] vprintk_emit+0x68/0x580
softirqs last enabled at (2010046): [<000000000045d278>] __do_softirq+0x378/0x4a0
softirqs last disabled at (2010039): [<000000000042bf08>] do_softirq_own_stack+0x28/0x40
Resetting ...
====================
Use local_* variables of the hw IRQ interfaces so that IRQ tracing sees
all of our changes.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 473ad7f4fb005d1bb727e4ef27d370d28703a062 ]
When we have to split up a flush request into multiple pieces
(in order to avoid the firmware range) we don't specify the
arguments in the right order for the second piece.
Fix the order, or else we get hangs as the code tries to
flush "a lot" of entries and we get lockups like this:
[ 4422.981276] NMI watchdog: BUG: soft lockup - CPU#12 stuck for 23s! [expect:117032]
[ 4422.996130] Modules linked in: ipv6 loop usb_storage igb ptp sg sr_mod ehci_pci ehci_hcd pps_core n2_rng rng_core
[ 4423.016617] CPU: 12 PID: 117032 Comm: expect Not tainted 3.17.0-rc4+ #1608
[ 4423.030331] task: fff8003cc730e220 ti: fff8003d99d54000 task.ti: fff8003d99d54000
[ 4423.045282] TSTATE: 0000000011001602 TPC: 00000000004521e8 TNPC: 00000000004521ec Y: 00000000 Not tainted
[ 4423.064905] TPC: <__flush_tlb_kernel_range+0x28/0x40>
[ 4423.074964] g0: 000000000052fd10 g1: 00000001295a8000 g2: ffffff7176ffc000 g3: 0000000000002000
[ 4423.092324] g4: fff8003cc730e220 g5: fff8003dfedcc000 g6: fff8003d99d54000 g7: 0000000000000006
[ 4423.109687] o0: 0000000000000000 o1: 0000000000000000 o2: 0000000000000003 o3: 00000000f0000000
[ 4423.127058] o4: 0000000000000080 o5: 00000001295a8000 sp: fff8003d99d56d01 ret_pc: 000000000052ff54
[ 4423.145121] RPC: <__purge_vmap_area_lazy+0x314/0x3a0>
[ 4423.155185] l0: 0000000000000000 l1: 0000000000000000 l2: 0000000000a38040 l3: 0000000000000000
[ 4423.172559] l4: fff8003dae8965e0 l5: ffffffffffffffff l6: 0000000000000000 l7: 00000000f7e2b138
[ 4423.189913] i0: fff8003d99d576a0 i1: fff8003d99d576a8 i2: fff8003d99d575e8 i3: 0000000000000000
[ 4423.207284] i4: 0000000000008008 i5: fff8003d99d575c8 i6: fff8003d99d56df1 i7: 0000000000530c24
[ 4423.224640] I7: <free_vmap_area_noflush+0x64/0x80>
[ 4423.234193] Call Trace:
[ 4423.239051] [0000000000530c24] free_vmap_area_noflush+0x64/0x80
[ 4423.251029] [0000000000531a7c] remove_vm_area+0x5c/0x80
[ 4423.261628] [0000000000531b80] __vunmap+0x20/0x120
[ 4423.271352] [000000000071cf18] n_tty_close+0x18/0x40
[ 4423.281423] [00000000007222b0] tty_ldisc_close+0x30/0x60
[ 4423.292183] [00000000007225a4] tty_ldisc_reinit+0x24/0xa0
[ 4423.303120] [0000000000722ab4] tty_ldisc_hangup+0xd4/0x1e0
[ 4423.314232] [0000000000719aa0] __tty_hangup+0x280/0x3c0
[ 4423.324835] [0000000000724cb4] pty_close+0x134/0x1a0
[ 4423.334905] [000000000071aa24] tty_release+0x104/0x500
[ 4423.345316] [00000000005511d0] __fput+0x90/0x1e0
[ 4423.354701] [000000000047fa54] task_work_run+0x94/0xe0
[ 4423.365126] [0000000000404b44] __handle_signal+0xc/0x2c
Fixes: 4ca9a23765da ("sparc64: Guard against flushing openfirmware mappings.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 35607b02dbef304fa5037236a3b43c1d8ab2aa52 ]
- fix BPF_LD|ABS|IND from negative offsets:
make sure to sign extend lower 32 bits in 64-bit register
before calling C helpers from JITed code, otherwise 'int k'
argument of bpf_internal_load_pointer_neg_helper() function
will be added as large unsigned integer, causing packet size
check to trigger and abort the program.
It's worth noting that JITed code for 'A = A op K' will affect
upper 32 bits differently depending whether K is simm13 or not.
Since small constants are sign extended, whereas large constants
are stored in temp register and zero extended.
That is ok and we don't have to pay a penalty of sign extension
for every sethi, since all classic BPF instructions have 32-bit
semantics and we only need to set correct upper bits when
transitioning from JITed code into C.
- though instructions 'A &= 0' and 'A *= 0' are odd, JIT compiler
should not optimize them out
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f6f2332dce0efeea8c5653b6e9d1e8c379ace65c ]
fix several issues in sparc BPF JIT compiler.
ldx/stx related:
. classic BPF instructions that access mem[] slots were not setting
SEEN_MEM flag, so stack wasn't allocated. Fix that by advertising
correct flags
. LDX/STX instructions were missing SEEN_XREG, so register value
could have leaked to user space. Fix it.
. since stack for mem[] slots is allocated with 'sub %sp' instead
of 'save %sp', use %sp as base register instead of %fp.
. ldx mem[0] means first slot in classic BPF which should have
-4 offset instead of 0.
. sparc64 needs 2047 stack bias as per ABI to access stack
. emit_stmem() was using LD32I macro instead of ST32I
SKF_AD_VLAN_TAG* related:
. SKF_AD_VLAN_TAG_PRESENT must return 1 or 0 instead of '> 0' or 0
as per classic BPF de facto standard
. SKF_AD_VLAN_TAG needs to mask the field correctly
Fixes: 2809a2087cc4 ("net: filter: Just In Time compiler for sparc")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 74cad25c076a2f5253312c2fe82d1a4daecc1323 ]
This makes memset follow the standard (instead of returning 0 on success). This
is needed when certain versions of gcc optimizes around memset calls and assume
that the address argument is preserved in %o0.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c21c4ab0d6921f7160a43216fa6973b5924de561 ]
The request_irq() needs to be done from ldc_alloc()
to avoid the following (caught by lockdep)
[00000000004a0738] __might_sleep+0xf8/0x120
[000000000058bea4] kmem_cache_alloc_trace+0x184/0x2c0
[00000000004faf80] request_threaded_irq+0x80/0x160
[000000000044f71c] ldc_bind+0x7c/0x220
[0000000000452454] vio_port_up+0x54/0xe0
[00000000101f6778] probe_disk+0x38/0x220 [sunvdc]
[00000000101f6b8c] vdc_port_probe+0x22c/0x300 [sunvdc]
[0000000000451a88] vio_device_probe+0x48/0x60
[000000000074c56c] really_probe+0x6c/0x300
[000000000074c83c] driver_probe_device+0x3c/0xa0
[000000000074c92c] __driver_attach+0x8c/0xa0
[000000000074a6ec] bus_for_each_dev+0x6c/0xa0
[000000000074c1dc] driver_attach+0x1c/0x40
[000000000074b0fc] bus_add_driver+0xbc/0x280
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3dee9df54836d5f844f3d58281d3f3e6331b467f ]
We have seen an issue with guest boot into LDOM that causes early boot failures
because of no matching rules for node identitity of the memory. I analyzed this
on my T4 and concluded there might not be a solution. I saw the issue in
mainline too when booting into the control/primary domain - with guests
configured. Note, this could be a firmware bug on some older machines.
I'll provide a full explanation of the issues below. Should we not find a
matching BEST latency group for a real address (RA) then we will assume node 0.
On the T4-2 here with the information provided I can't see an alternative.
Technically the LDOM shown below should match the MBLOCK to the
favorable latency group. However other factors must be considered too. Were
the memory controllers configured "fine" grained interleave or "coarse"
grain interleaved - T4. Also should a "group" MD node be considered a NUMA
node?
There has to be at least one Machine Description (MD) "group" and hence one
NUMA node. The group can have one or more latency groups (lg) - more than one
memory controller. The current code chooses the smallest latency as the most
favorable per group. The latency and lg information is in MLGROUP below.
MBLOCK is the base and size of the RAs for the machine as fetched from OBP
/memory "available" property. My machine has one MBLOCK but more would be
possible - with holes?
For a T4-2 the following information has been gathered:
with LDOM guest
MEMBLOCK configuration:
memory size = 0x27f870000
memory.cnt = 0x3
memory[0x0] [0x00000020400000-0x0000029fc67fff], 0x27f868000 bytes
memory[0x1] [0x0000029fd8a000-0x0000029fd8bfff], 0x2000 bytes
memory[0x2] [0x0000029fd92000-0x0000029fd97fff], 0x6000 bytes
reserved.cnt = 0x2
reserved[0x0] [0x00000020800000-0x000000216c15c0], 0xec15c1 bytes
reserved[0x1] [0x00000024800000-0x0000002c180c1e], 0x7980c1f bytes
MBLOCK[0]: base[20000000] size[280000000] offset[0]
(note: "base" and "size" reported in "MBLOCK" encompass the "memory[X]" values)
(note: (RA + offset) & mask = val is the formula to detect a match for the
memory controller. should there be no match for find_node node, a return
value of -1 resulted for the node - BAD)
There is one group. It has these forward links
MLGROUP[1]: node[545] latency[1f7e8] match[200000000] mask[200000000]
MLGROUP[2]: node[54d] latency[2de60] match[0] mask[200000000]
NUMA NODE[0]: node[545] mask[200000000] val[200000000] (latency[1f7e8])
(note: "val" is the best lg's (smallest latency) "match")
no LDOM guest - bare metal
MEMBLOCK configuration:
memory size = 0xfdf2d0000
memory.cnt = 0x3
memory[0x0] [0x00000020400000-0x00000fff6adfff], 0xfdf2ae000 bytes
memory[0x1] [0x00000fff6d2000-0x00000fff6e7fff], 0x16000 bytes
memory[0x2] [0x00000fff766000-0x00000fff771fff], 0xc000 bytes
reserved.cnt = 0x2
reserved[0x0] [0x00000020800000-0x00000021a04580], 0x1204581 bytes
reserved[0x1] [0x00000024800000-0x0000002c7d29fc], 0x7fd29fd bytes
MBLOCK[0]: base[20000000] size[fe0000000] offset[0]
there are two groups
group node[16d5]
MLGROUP[0]: node[1765] latency[1f7e8] match[0] mask[200000000]
MLGROUP[3]: node[177d] latency[2de60] match[200000000] mask[200000000]
NUMA NODE[0]: node[1765] mask[200000000] val[0] (latency[1f7e8])
group node[171d]
MLGROUP[2]: node[1775] latency[2de60] match[0] mask[200000000]
MLGROUP[1]: node[176d] latency[1f7e8] match[200000000] mask[200000000]
NUMA NODE[1]: node[176d] mask[200000000] val[200000000] (latency[1f7e8])
(note: for this two "group" bare metal machine, 1/2 memory is in group one's
lg and 1/2 memory is in group two's lg).
Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 84bd6d8b9c0f06b3f188efb479c77e20f05e9a8a ]
Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.
Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:
1) For pre-hypervisor TLB protection violation traps, if we took
the 'winfix_trampoline' path we wouldn't have %g4 initialized
with the FAULT_CODE_* value yet. Resulting in using the
TLB_TAG_ACCESS register address value instead.
2) In the TSB miss path, when we notice that we are going to use a
hugepage mapping, but we haven't allocated the hugepage TSB yet, we
still have to take the window fixup case into consideration and
in that particular path we leave %g4 not setup properly.
Errors on this sort were largely invisible previously, but after
commit 4ccb9272892c33ef1c19a783cfa87103b30c2784 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.
FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.
Fixes: 4ccb9272892c ("sparc64: sun4v TLB error power off events")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4ccb9272892c33ef1c19a783cfa87103b30c2784 ]
We've witnessed a few TLB events causing the machine to power off because
of prom_halt. In one case it was some nfs related area during rmmod. Another
was an mmapper of /dev/mem. A more recent one is an ITLB issue with
a bad pagesize which could be a hardware bug. Bugs happen but we should
attempt to not power off the machine and/or hang it when possible.
This is a DTLB error from an mmapper of /dev/mem:
[root@sparcie ~]# SUN4V-DTLB: Error at TPC[fffff80100903e6c], tl 1
SUN4V-DTLB: TPC<0xfffff80100903e6c>
SUN4V-DTLB: O7[fffff801081979d0]
SUN4V-DTLB: O7<0xfffff801081979d0>
SUN4V-DTLB: vaddr[fffff80100000000] ctx[1250] pte[98000000000f0610] error[2]
.
This is recent mainline for ITLB:
[ 3708.179864] SUN4V-ITLB: TPC<0xfffffc010071cefc>
[ 3708.188866] SUN4V-ITLB: O7[fffffc010071cee8]
[ 3708.197377] SUN4V-ITLB: O7<0xfffffc010071cee8>
[ 3708.206539] SUN4V-ITLB: vaddr[e0003] ctx[1a3c] pte[2900000dcc800eeb] error[4]
.
Normally sun4v_itlb_error_report() and sun4v_dtlb_error_report() would call
prom_halt() and drop us to OF command prompt "ok". This isn't the case for
LDOMs and the machine powers off.
For the HV reported error of HV_ENORADDR for HV HV_MMU_MAP_ADDR_TRAP we cause
a SIGBUS error by qualifying it within do_sparc64_fault() for fault code mask
of FAULT_CODE_BAD_RA. This is done when trap level (%tl) is less or equal
one("1"). Otherwise, for %tl > 1, we proceed eventually to die_if_kernel().
The logic of this patch was partially inspired by David Miller's feedback.
Power off of large sparc64 machines is painful. Plus die_if_kernel provides
more context. A reset sequence isn't a brief period on large sparc64 but
better than power-off/power-on sequence.
Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d1105287aabe88dbb3af825140badaa05cf0442c ]
dma_zalloc_coherent() calls dma_alloc_coherent(__GFP_ZERO)
but the sparc32 implementations sbus_alloc_coherent() and
pci32_alloc_coherent() doesn't take the gfp flags into
account.
Tested on the SPARC32/LEON GRETH Ethernet driver which fails
due to dma_alloc_coherent(__GFP_ZERO) returns non zeroed
pages.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8bccf5b313180faefce38e0d1140f76e0f327d28 ]
Christopher reports that perf_event_print_debug() can crash in uniprocessor
builds. The crash is due to pcr_ops being NULL.
This happens because pcr_arch_init() is only invoked by smp_cpus_done() which
only executes in SMP builds.
init_hw_perf_events() is closely intertwined with pcr_ops being setup properly,
therefore:
1) Call pcr_arch_init() early on from init_hw_perf_events(), instead of
from smp_cpus_done().
2) Do not hook up a PMU type if pcr_ops is NULL after pcr_arch_init().
3) Move init_hw_perf_events to a later initcall so that it we will be
sure to invoke pcr_arch_init() after all cpus are brought up.
Finally, guard the one naked sequence of pcr_ops dereferences in
__global_pmu_self() with an appropriate NULL check.
Reported-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 58556104e9cd0107a7a8d2692cf04ef31669f6e4 ]
nmi_cpu_busy() is a SMP function call that just makes sure that all of the
cpus are spinning using cpu cycles while the NMI test runs.
It does not need to disable IRQs because we just care about NMIs executing
which will even with 'normal' IRQs disabled.
It is not legal to enable hard IRQs in a SMP cross call, in fact this bug
triggers the BUG check in irq_work_run_list():
BUG_ON(!irqs_disabled());
Because now irq_work_run() is invoked from the tail of
generic_smp_call_function_single_interrupt().
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 093758e3daede29cb4ce6aedb111becf9d4bfc57 ]
This commit is a guesswork, but it seems to make sense to drop this
break, as otherwise the following line is never executed and becomes
dead code. And that following line actually saves the result of
local calculation by the pointer given in function argument. So the
proposed change makes sense if this code in the whole makes sense (but I
am unable to analyze it in the whole).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81641
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4ec1b01029b4facb651b8ef70bc20a4be4cebc63 ]
The LDC handshake could have been asynchronously triggered
after ldc_bind() enables the ldc_rx() receive interrupt-handler
(and thus intercepts incoming control packets)
and before vio_port_up() calls ldc_connect(). If that is the case,
ldc_connect() should return 0 and let the state-machine
progress.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4ca9a23765da3260058db3431faf5b4efd8cf926 ]
Based almost entirely upon a patch by Christopher Alexander Tobias
Schulze.
In commit db64fe02258f1507e13fe5212a989922323685ce ("mm: rewrite vmap
layer") lazy VMAP tlb flushing was added to the vmalloc layer. This
causes problems on sparc64.
Sparc64 has two VMAP mapped regions and they are not contiguous with
eachother. First we have the malloc mapping area, then another
unrelated region, then the vmalloc region.
This "another unrelated region" is where the firmware is mapped.
If the lazy TLB flushing logic in the vmalloc code triggers after
we've had both a module unload and a vfree or similar, it will pass an
address range that goes from somewhere inside the malloc region to
somewhere inside the vmalloc region, and thus covering the
openfirmware area entirely.
The sparc64 kernel learns about openfirmware's dynamic mappings in
this region early in the boot, and then services TLB misses in this
area. But openfirmware has some locked TLB entries which are not
mentioned in those dynamic mappings and we should thus not disturb
them.
These huge lazy TLB flush ranges causes those openfirmware locked TLB
entries to be removed, resulting in all kinds of problems including
hard hangs and crashes during reboot/reset.
Besides causing problems like this, such huge TLB flush ranges are
also incredibly inefficient. A plea has been made with the author of
the VMAP lazy TLB flushing code, but for now we'll put a safety guard
into our flush_tlb_kernel_range() implementation.
Since the implementation has become non-trivial, stop defining it as a
macro and instead make it a function in a C source file.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 18f38132528c3e603c66ea464727b29e9bbcb91b ]
The assumption was that update_mmu_cache() (and the equivalent for PMDs) would
only be called when the PTE being installed will be accessible by the user.
This is not true for code paths originating from remove_migration_pte().
There are dire consequences for placing a non-valid PTE into the TSB. The TLB
miss frramework assumes thatwhen a TSB entry matches we can just load it into
the TLB and return from the TLB miss trap.
So if a non-valid PTE is in there, we will deadlock taking the TLB miss over
and over, never satisfying the miss.
Just exit early from update_mmu_cache() and friends in this situation.
Based upon a report and patch from Christopher Alexander Tobias Schulze.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The optimistic spin code assumes regular stores and cmpxchg() play nice;
this is found to not be true for at least: parisc, sparc32, tile32,
metag-lock1, arc-!llsc and hexagon.
There is further wreckage, but this in particular seemed easy to
trigger, so blacklist this.
Opt in for known good archs.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: John David Anglin <dave.anglin@bell.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: stable@vger.kernel.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/20140606175316.GV13930@laptop.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Sometimes it is preferred not to use the trigger_all_cpu_backtrace()
routine when one wants to avoid capturing a back trace for current. For
instance if one was previously captured recently.
This patch provides a new routine namely
trigger_allbutself_cpu_backtrace() which offers the flexibility to issue
an NMI to every cpu but current and capture a back trace accordingly.
Patch x86 and sparc to support new routine.
[dzickus@redhat.com: add stub in #else clause]
[dzickus@redhat.com: don't print message in single processor case, wrap with get/put_cpu based on Oleg's suggestion]
[sfr@canb.auug.org.au: undo C99ism]
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull sparc fixes from David Miller:
"Sparc sparse fixes from Sam Ravnborg"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next: (67 commits)
sparc64: fix sparse warnings in int_64.c
sparc64: fix sparse warning in ftrace.c
sparc64: fix sparse warning in kprobes.c
sparc64: fix sparse warning in kgdb_64.c
sparc64: fix sparse warnings in compat_audit.c
sparc64: fix sparse warnings in init_64.c
sparc64: fix sparse warnings in aes_glue.c
sparc: fix sparse warnings in smp_32.c + smp_64.c
sparc64: fix sparse warnings in perf_event.c
sparc64: fix sparse warnings in kprobes.c
sparc64: fix sparse warning in tsb.c
sparc64: clean up compat_sigset_t.seta handling
sparc64: fix sparse "Should it be static?" warnings in signal32.c
sparc64: fix sparse warnings in sys_sparc32.c
sparc64: fix sparse warning in pci.c
sparc64: fix sparse warnings in smp_64.c
sparc64: fix sparse warning in prom_64.c
sparc64: fix sparse warning in btext.c
sparc64: fix sparse warnings in sys_sparc_64.c + unaligned_64.c
sparc64: fix sparse warning in process_64.c
...
Conflicts:
arch/sparc/include/asm/pgtable_64.h
|
|
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
|
|
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 569810d1e327 ("net: filter: fix typo in sparc BPF JIT")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix typo in sparc codegen for SKF_AD_IFINDEX and SKF_AD_HATYPE
classic BPF extensions
Fixes: 2809a2087cc4 ("net: filter: Just In Time compiler for sparc")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sys_sgetmask and sys_ssetmask are obsolete system calls no longer
supported in libc.
This patch replaces architecture related __ARCH_WANT_SYS_SGETMAX by expert
mode configuration.That option is enabled by default for those
architectures.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs. So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.
Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle were:
- reduced/streamlined smp_mb__*() interface that allows more usecases
and makes the existing ones less buggy, especially in rarer
architectures
- add rwsem implementation comments
- bump up lockdep limits"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
rwsem: Add comments to explain the meaning of the rwsem's count field
lockdep: Increase static allocations
arch: Mass conversion of smp_mb__*()
arch,doc: Convert smp_mb__*()
arch,xtensa: Convert smp_mb__*()
arch,x86: Convert smp_mb__*()
arch,tile: Convert smp_mb__*()
arch,sparc: Convert smp_mb__*()
arch,sh: Convert smp_mb__*()
arch,score: Convert smp_mb__*()
arch,s390: Convert smp_mb__*()
arch,powerpc: Convert smp_mb__*()
arch,parisc: Convert smp_mb__*()
arch,openrisc: Convert smp_mb__*()
arch,mn10300: Convert smp_mb__*()
arch,mips: Convert smp_mb__*()
arch,metag: Convert smp_mb__*()
arch,m68k: Convert smp_mb__*()
arch,m32r: Convert smp_mb__*()
arch,ia64: Convert smp_mb__*()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into next
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Notify driver before and after device reset (Keith Busch)
- Use reset notification in NVMe (Keith Busch)
NUMA
- Warn if we have to guess host bridge node information (Myron Stowe)
- Work around AMD Fam15h BIOSes that fail to provide _PXM (Suravee
Suthikulpanit)
- Clean up and mark early_root_info_init() as deprecated (Suravee
Suthikulpanit)
Driver binding
- Add "driver_override" for force specific binding (Alex Williamson)
- Fail "new_id" addition for devices we already know about (Bandan
Das)
Resource management
- Support BAR sizes up to 8GB (Nikhil Rao, Alan Cox)
- Don't move IORESOURCE_PCI_FIXED resources (Bjorn Helgaas)
- Mark SBx00 HPET BAR as IORESOURCE_PCI_FIXED (Bjorn Helgaas)
- Fail safely if we can't handle BARs larger than 4GB (Bjorn Helgaas)
- Reject BAR above 4GB if dma_addr_t is too small (Bjorn Helgaas)
- Don't convert BAR address to resource if dma_addr_t is too small
(Bjorn Helgaas)
- Don't set BAR to zero if dma_addr_t is too small (Bjorn Helgaas)
- Don't print anything while decoding is disabled (Bjorn Helgaas)
- Don't add disabled subtractive decode bus resources (Bjorn Helgaas)
- Add resource allocation comments (Bjorn Helgaas)
- Restrict 64-bit prefetchable bridge windows to 64-bit resources
(Yinghai Lu)
- Assign i82875p_edac PCI resources before adding device (Yinghai Lu)
PCI device hotplug
- Remove unnecessary "dev->bus" test (Bjorn Helgaas)
- Use PCI_EXP_SLTCAP_PSN define (Bjorn Helgaas)
- Fix rphahp endianess issues (Laurent Dufour)
- Acknowledge spurious "cmd completed" event (Rajat Jain)
- Allow hotplug service drivers to operate in polling mode (Rajat Jain)
- Fix cpqphp possible NULL dereference (Rickard Strandqvist)
MSI
- Replace pci_enable_msi_block() by pci_enable_msi_exact()
(Alexander Gordeev)
- Replace pci_enable_msix() by pci_enable_msix_exact() (Alexander Gordeev)
- Simplify populate_msi_sysfs() (Jan Beulich)
Virtualization
- Add Intel Patsburg (X79) root port ACS quirk (Alex Williamson)
- Mark RTL8110SC INTx masking as broken (Alex Williamson)
Generic host bridge driver
- Add generic PCI host controller driver (Will Deacon)
Freescale i.MX6
- Use new clock names (Lucas Stach)
- Drop old IRQ mapping (Lucas Stach)
- Remove optional (and unused) IRQs (Lucas Stach)
- Add support for MSI (Lucas Stach)
- Fix imx6_add_pcie_port() section mismatch warning (Sachin Kamat)
Renesas R-Car
- Add gen2 device tree support (Ben Dooks)
- Use new OF interrupt mapping when possible (Lucas Stach)
- Add PCIe driver (Phil Edworthy)
- Add PCIe MSI support (Phil Edworthy)
- Add PCIe device tree bindings (Phil Edworthy)
Samsung Exynos
- Remove unnecessary OOM messages (Jingoo Han)
- Fix add_pcie_port() section mismatch warning (Sachin Kamat)
Synopsys DesignWare
- Make MSI ISR shared IRQ aware (Lucas Stach)
Miscellaneous
- Check for broken config space aliasing (Alex Williamson)
- Update email address (Ben Hutchings)
- Fix Broadcom CNB20LE unintended sign extension (Bjorn Helgaas)
- Fix incorrect vgaarb conditional in WARN_ON() (Bjorn Helgaas)
- Remove unnecessary __ref annotations (Bjorn Helgaas)
- Add arch/x86/kernel/quirks.c to MAINTAINERS PCI file patterns
(Bjorn Helgaas)
- Fix use of uninitialized MPS value (Bjorn Helgaas)
- Tidy x86/gart messages (Bjorn Helgaas)
- Fix return value from pci_user_{read,write}_config_*() (Gavin Shan)
- Turn pcibios_penalize_isa_irq() into a weak function (Hanjun Guo)
- Remove unused serial device IDs (Jean Delvare)
- Use designated initialization in PCI_VDEVICE (Mark Rustad)
- Fix powerpc NULL dereference in pci_root_buses traversal (Mike Qiu)
- Configure MPS on ARM (Murali Karicheri)
- Remove unnecessary includes of <linux/init.h> (Paul Gortmaker)
- Move Open Firmware devspec attribute to PCI common code (Sebastian Ott)
- Use pdev->dev.groups for attribute creation on s390 (Sebastian Ott)
- Remove pcibios_add_platform_entries() (Sebastian Ott)
- Add new ID for Intel GPU "spurious interrupt" quirk (Thomas Jarosch)
- Rename pci_is_bridge() to pci_has_subordinate() (Yijing Wang)
- Add and use new pci_is_bridge() interface (Yijing Wang)
- Make pci_bus_add_device() void (Yijing Wang)
DMA API
- Clarify physical/bus address distinction in docs (Bjorn Helgaas)
- Fix typos in docs (Emilio López)
- Update dma_pool_create ()and dma_pool_alloc() descriptions (Gioh Kim)
- Change dma_declare_coherent_memory() CPU address to phys_addr_t
(Bjorn Helgaas)
- Pass GAPSPCI_DMA_BASE CPU & bus address to dma_declare_coherent_memory()
(Bjorn Helgaas)"
* tag 'pci-v3.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
MAINTAINERS: Add generic PCI host controller driver
PCI: generic: Add generic PCI host controller driver
PCI: imx6: Add support for MSI
PCI: designware: Make MSI ISR shared IRQ aware
PCI: imx6: Remove optional (and unused) IRQs
PCI: imx6: Drop old IRQ mapping
PCI: imx6: Use new clock names
i82875p_edac: Assign PCI resources before adding device
ARM/PCI: Call pcie_bus_configure_settings() to set MPS
PCI: imx6: Fix imx6_add_pcie_port() section mismatch warning
PCI: Make pci_bus_add_device() void
PCI: exynos: Fix add_pcie_port() section mismatch warning
PCI: Introduce new device binding path using pci_dev.driver_override
PCI: rcar: Add gen2 device tree support
PCI: cpqphp: Fix possible null pointer dereference
PCI: rcar: Add R-Car PCIe device tree bindings
PCI: rcar: Add MSI support for PCIe
PCI: rcar: Add Renesas R-Car PCIe driver
PCI: Fix return value from pci_user_{read,write}_config_*()
PCI: exynos: Remove unnecessary OOM messages
...
|
|
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* pci/misc:
PCI: Fix return value from pci_user_{read,write}_config_*()
PCI: Turn pcibios_penalize_isa_irq() into a weak function
PCI: Test for std config alias when testing extended config space
|
|
pcibios_penalize_isa_irq() is only implemented by x86 now, and legacy ISA
is not used by some architectures. Make pcibios_penalize_isa_irq() a
__weak function to simplify the code. This removes the need for new
platforms to add stub implementations of pcibios_penalize_isa_irq().
[bhelgaas: changelog, comments]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae741 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c9423 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
