| Age | Commit message (Collapse) | Author |
|---|
|
Some of the were relying into smp.h being dragged in by another header
which of course is fragile. <asm/cpu-info.h> uses smp_processor_id()
only in macros and including smp.h there leads to an include loop, so
don't change cpu-info.h.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The TLB handlers need to check for huge pages and give them special
handling. Huge pages consist of two contiguous sub-pages of physical
memory.
* Loading entrylo0 and entrylo1 need to be handled specially.
* The page mask must be set for huge pages and then restored after
writing the TLB entries.
* The PTE for huge pages resides in the PMD, we halt traversal of the
tables there.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The l parameter to iPTE_LW() is unused. Remove it and from some of its
callers as well.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
CPU_CAVIUM_OCTEON is mips_r2 which is handled before the switch. This
label in the switch statement is dead code, so we remove it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Some CPUs do not need ehb instructions after writing CP0 registers.
By allowing ehb generation to be overridden in
cpu-feature-overrides.h, we can save a few instructions in the TLB
handler hot paths.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Try to fold the 64-bit TLB refill handler opportunistically at the
beginning of the vmalloc path so as to avoid splitting execution flow in
half and wasting cycles for a branch required at that point then. Resort
to doing the split if either of the newly created parts would not fit into
its designated slot.
Original-patch-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The logic used to split the r4000 refill handler is liberally
sprinkled with magic numbers. We attempt to explain what they are and
normalize them against a new symbolic value (MIPS64_REFILL_INSNS).
CC: David VomLehn <dvomlehn@cisco.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The Alchemy manuals state:
"All pipeline hazards and dependencies are enforced by hardware interlocks
so that any sequence of instructions is guaranteed to execute correctly.
Therefore, it is not necessary to pad legacy MIPS hazards (such as
load delay slots and coprocessor accesses) with NOPs."
Run-tested on Au12x0, without any ill effects.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch removes the various CPU_AU1??? model constants in favor of
a single CPU_ALCHEMY one.
All currently existing Alchemy models are identical in terms of cpu
core and cache size/organization. The parts of the mips kernel which
need to know the exact CPU revision extract it from the c0_prid register
already; and finally nothing else in-tree depends on those any more.
Should a new variant with slightly different "company options" and/or
"processor revision" bits in c0_prid appear, it will be supported
immediately (minus an exact model string in cpuinfo).
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Current VR5500 processor support lacks of some functions which are
expected to be configured/synthesized on arch initialization.
Here're some VR5500A spec notes:
* All execution hazards are handled in hardware.
* Once VR5500A stops the operation of the pipeline by WAIT instruction,
it could return from the standby mode only when either a reset, NMI
request, or all enabled interrupts is/are detected. In other words,
if interrupts are disabled by Status.IE=0, it keeps in standby mode
even when interrupts are internally asserted.
Notes on WAIT: The operation of the processor is undefined if WAIT
insn is in the branch delay slot. The operation is also undefined
if WAIT insn is executed when Status.EXL and Status.ERL are set to 1.
* VR5500A core only implements the Load prefetch.
With these changes, it boots fine.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Expand the case statement for build_tlb_write_entry so that it does
the right thing on Cavium CPU variants.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
trap_init issues flush_icache_range(), which uses ipi functions to
get icache flushing done on all cpus. But this is done before interrupts
are enabled and caused WARN_ON messages. This changeset introduces
a new local_flush_icache_range() and uses it before interrupts (and
additional CPUs) are enabled to avoid this problem.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Treat R4700 like R4600 in build_tlb_probe_entry. Without this fix kernel
will lock up.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Early 4KEc were MIPS32r1 and therefore need some love to get a TLB
refill handler.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch moves the micro-assembler in a separate implementation, as
it is useful for further run-time optimizations. The only change in
behaviour is cutting down printk noise at kernel startup time.
Checkpatch complains about macro parameters which aren't protected by
parentheses. I believe this is a flaw in checkpatch, the paste operator
used in those macros won't work with parenthesised parameters.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch adds IDs for new Au1200 variants: Au1210 and Au1250.
They are essentially identical to the Au1200 except for the Au1210
which has a different SoC-ID in the PRId register [bits 31:24].
The Au1250 is a "Au1200 V0.2".
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This complements the generic R4000/R4400 errata workaround code and adds
bits for the daddiu problem. In most places it just modifies handwritten
assembly code so that the assembler is allowed to use a temporary register
as daddiu may now be treated as a macro that expands to a sequence of li
and daddu. It is the AT register or, where AT is unavailable or used
explicitly for another purpose, an explicitly-named register is selected,
using the .set at=<reg> feature added recently to gas. This feature is
only used if CONFIG_CPU_DADDI_WORKAROUNDS has been set, so if the
workaround remains disabled, the required version of binutils stays
unchanged.
Similarly, daddiu instructions put in branch delay slots in noreorder
fragments are now taken out of them and the assembler is allowed to
reorder them itself as possible (which it does making the whole idea of
scheduling them into delay slots manually questionable).
Also in the very few places where such a simple conversion was not
possible, a handcoded longer sequence is implemented.
Other than that there are changes to code responsible for building the
TLB fault and page clear/copy handlers to avoid daddiu as appropriate.
These are only effective if the erratum is verified to be present at the
run time.
Finally there is a trivial update to __delay(), because it uses daddiu in
a branch delay slot.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This reverts commit aaf76a3245c02faba51c96b9a340c14d6bb0dcc0.
As requested by ranck Bui-Huu <fbuihuu@gmail.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This saves a few k on systems which only ever ship with a single CPU type.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Note that the BCM4710 does not support the wait instruction, this
is not a mistake in the code.
It originally comes from the OpenWrt patches.
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Florian Schirmer <jolt@tuxbox.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-Off-By: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Fuxin Zhang <zhangfx@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Replace function instances of __attribute__((unused)) with
__maybe_unused.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This is a patch to load 64-bit modules to CKSEG0 so that can be
compiled with -msym32 option. This makes each module ~10% smaller.
* introduce MODULE_START and MODULE_END
* custom module_alloc()
* PGD for modules
* change XTLB refill handler synthesizer
* enable -msym32 for modules again
(revert ca78b1a5c6a6e70e052d3ea253828e49b5d07c8a)
New XTLB refill handler looks like this:
80000080 dmfc0 k0,C0_BADVADDR
80000084 bltz k0,800000e4 # goto l_module_alloc
80000088 lui k1,0x8046 # %high(pgd_current)
8000008c ld k1,24600(k1) # %low(pgd_current)
80000090 dsrl k0,k0,0x1b # l_vmalloc_done:
80000094 andi k0,k0,0x1ff8
80000098 daddu k1,k1,k0
8000009c dmfc0 k0,C0_BADVADDR
800000a0 ld k1,0(k1)
800000a4 dsrl k0,k0,0x12
800000a8 andi k0,k0,0xff8
800000ac daddu k1,k1,k0
800000b0 dmfc0 k0,C0_XCONTEXT
800000b4 ld k1,0(k1)
800000b8 andi k0,k0,0xff0
800000bc daddu k1,k1,k0
800000c0 ld k0,0(k1)
800000c4 ld k1,8(k1)
800000c8 dsrl k0,k0,0x6
800000cc mtc0 k0,C0_ENTRYLO0
800000d0 dsrl k1,k1,0x6
800000d4 mtc0 k1,C0_ENTRYL01
800000d8 nop
800000dc tlbwr
800000e0 eret
800000e4 dsll k1,k0,0x2 # l_module_alloc:
800000e8 bgez k1,80000008 # goto l_vmalloc
800000ec lui k1,0xc000
800000f0 dsubu k0,k0,k1
800000f4 lui k1,0x8046 # %high(module_pg_dir)
800000f8 beq zero,zero,80000000
800000fc nop
80000000 beq zero,zero,80000090 # goto l_vmalloc_done
80000004 daddiu k1,k1,0x4000
80000008 dsll32 k1,k1,0x0 # l_vmalloc:
8000000c dsubu k0,k0,k1
80000010 beq zero,zero,80000090 # goto l_vmalloc_done
80000014 lui k1,0x8046 # %high(swapper_pg_dir)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Derived from Peter Watkins <treestem@gmail.com>'s work.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The patch below corrects multiple occurances of "the the"
typos across several files, both in source comments and KConfig files.
There is no actual code changed, only text. Note this only affects the /arch
directory, and I believe I could find many more elsewhere. :)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Small update, using pr_debug and pr_info.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Nothing exciting; Linux just didn't know it yet so this is most adding
a value to a case statement.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This option is no longer usable with supported compilers. It will be
replaced by usage of -msym32 in a separate patch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Found by make buildcheck.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
will also avoid smp_call_function from doing stupid things when called
from a CPU that is not yet marked online.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
