Age | Commit message (Collapse) | Author |
|
A previous patch converted the Alchemy platform to use the OHCI and EHCI
platform drivers. As a result, all the common logic to handle USB present in
drivers/usb/host/alchemy-common.c has no reason to remain here, so we move it
to arch/mips/alchemy/common/usb.c which is a more appropriate place. This
change was suggested by Manuel Lauss.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert the Alchemy platform to register the ohci-platform driver, now that
the ohci-platform driver properly handles the specific ohci-au1xxx resume
from suspend case.
This also greatly simplifies the power_{on,off} callbacks and make them
work on platform device id instead of checking the OHCI controller base
address like what was done in ohci-au1xxx.c.
Impacted defconfigs are also updated accordingly to select the OHCI platform
driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the ehci platform driver power_{on,suspend,off} callbacks to perform the
USB block gate enabling/disabling as what the ehci-au1xxx.c driver does.
Update the db1200 and db1300 defconfigs to now select the EHCI platform
driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PB1100/1500 are similar to their DB-cousins but with a few
more devices on the bus.
This patch adds PB1100/1500 support to the existing DB1100/1500
code.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: lnux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The PB1550 is more or less a DB1550 without the PCI IDE controller,
a more complicated (read: configurable) Flash setup and some other
minor changes. Like the DB1550 it can be automatically detected by
reading the CPLD ID register bits.
This patch adds PB1550 detection and setup to the DB1550 code.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Combine support for the DB1200/PB1200, DB1300 and DB1550 boards into
a single kernel image.
defconfig-generated image verified on DB1200, DB1300 and DB1550.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4335/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Without this udelay(1) PCI idsel does not work correctly on the
"singleboard" (T-Mobile Surfbox) for the MiniPCI device. The result is
that PCI configuration fails and the MiniPCI card is not detected
correctly. Instead of
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
We see only the CardBus device:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x40000fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40001000-0x40001fff]
Later the device driver shows this error:
ath5k 0000:00:03.0: cannot remap PCI memory region
ath5k: probe of 0000:00:03.0 failed with error -5
I assume that the logic chip which usually supresses the signal to the CardBus
card has some settling time and without the delay it would still let the
Cardbus interfere with the response from the MiniPCI card.
What I cannot explain is why this behaviour shows up now and not in earlier
kernel versions before. Maybe older PCI code was slower?
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: linux-mips@linux-mips.org
Cc: manuel.lauss@googlemail.com
Cc: florian@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/4087/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
'next/cavium', 'next/jz4740', 'next/lantiq', 'next/loongson1b' and 'next/netlogic' into mips-for-linux-next
|
|
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3058/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3331/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove the loop in the cascade handler and instead unconditionally
handle just the first set interrupt coming from the CPLD.
This gets rid of a lot of spurious interrupts being triggered for
the SMSC91111 ethernet chip especially under high(er) IDE load:
"eth0: spurious interrupt (mask = 0xb3)"
Verified on DB1200 and DB1300.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3288/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
move contents to already existing platform.c file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3287/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
YAMON on all devboards provides the "memsize" envvar; in the unlikely
case that it can't be parsed just assume 64MB, which all boards have
at least.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3286/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
|
|
These will show up as a build failure once we clean up a
misuse of module.h in the mips termios header.
Uses export.h: (EXPORT_SYMBOL)
arch/mips/cavium-octeon/setup.c
arch/mips/pmc-sierra/yosemite/setup.c
arch/mips/rb532/devices.c
arch/mips/sni/setup.c
Uses module.h: (symbol_get/put)
arch/mips/alchemy/devboards/db1200.c
Uses module.h: (print_modules)
arch/mips/kernel/traps.c
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3448/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Use the default partition parser, cmdlinepart, provided by the plat_nand driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Since a clocksource change post 3.2-rc1, tasks on my DB1500 board
hang after random amounts of time (from a few minutes to a few hours),
regardless of load. Debugging showed that the compare-match register
value is a few seconds lower than the current counter value.
The minimum value of 8 was initialy determined by a trial-and-error
approach. Currently it is sufficient for all Alchemys (without PCI
apparently), independent of CPU clock; only the DB1500 and DB1550
boards experience these timer-related tasks hangs now.
This patch increases the minimum timeout by 1 (to 9 counter ticks)
which seems sufficient since the systems are still working perfectly
fine after over 24 hours.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3214/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
|
|
The PB1200 has the CPLD located at an address which on the DB1200 is
RAM; reading the Board-ID sometimes results in a PB1200 being detected
instead (especially during reboots after long uptimes).
On the other hand, the address of the DB1200's CPLD is hosting Flash
chips on the PB1200. Test for the DB1200 first and additionally do a
quick write-test to the hexleds register to make sure we're writing
to the CPLD.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
With a generic plat_irq_dispatch (for Alchemy at least) code for both
interrupt controller types can coexist in a single kernel image and be
autodetected at runtime.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2935/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
IC and GPIC are now chain handlers of the traditional MIPS IRQ controller.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2933/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
No need for a device_initcall.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2934/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Wire up the ADS7846 touchscreen controller on the DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2879/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add necessary transceiver control platform data and hook up the
IrDA peripheral on the DB1000 and DB1100 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The information in those headers is no longer necessary.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2876/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Transform the au1550nd.c driver into a platform_driver and hook it
up in the PB1550 board (gen_nand works fine on the DB1550, but since
I don't have a PB1550 to test this driver stays for now).
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mtd@lists.infradead.org
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2875/
Patchwork: https://patchwork.linux-mips.org/patch/3160/
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled and we even check
and yell when an interrupt handler returns with interrupts enabled (see
commit [b738a50a: genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
[ralf@linux-mips.org: Fixed up conflicts in
arch/mips/alchemy/common/dbdma.c, arch/mips/cavium-octeon/smp.c and
arch/mips/kernel/perf_event.c.]
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.de
linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
All Devboards can use the 32kHz counter as a RTC device.
Also delete the custom CMOS RTC header, which can be used for the
DS1693 on the PB1500. But since it doesn't have a buffer battery
it is as useful as the on-chip RTC which I prefer.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch hooks up the 2 MMC sockets on the DB1100 board.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2873/
Patchwork: https://patchwork.linux-mips.org/patch/2920/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.
Tested on DB1500 and DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The PB1200 is basically a DB1200 with additional MMC and camera sockets
and different base addresses for external hardware (CPLD, IDE, Net, NAND).
This patch implements the missing PB1200 features in DB1200 support code
and runtime board detection.
Tested on DB1200 only.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2880/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
au1200fb calls 3 functions which have to be defined in board code.
Fix this ugliness with the introduction of platform_data.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-fbdev@vger.kernel.org
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2871/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Most of these files are have more comments than real code; merge
them all into single board-<name>.c files.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2869/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2868/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2867/
Patchwork: https://patchwork.linux-mips.org/patch/2919/
Patchwork: https://patchwork.linux-mips.org/patch/2928/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Initially I had to write to both the MASK and ENABLE registers, otherwise
the CPLD would generate tons of spurious interrupts. With the change to
the demux handler to disable the muxed line, it is now sufficient to
disable the interrupt by writing either the enable or mask register.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
No test hardware and no (apparent) users. These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2864/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Noone seems to have test hardware or care anymore. Drop PB1000 support
and along with it the old Alchemy PCMCIA socket driver.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Cc: linux-pcmcia@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/2881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (37 commits)
MIPS: O32: Provide definition of registers ta0 .. ta3.
MIPS: perf: Add Octeon support for hardware perf.
MIPS: perf: Add support for 64-bit perf counters.
MIPS: perf: Reorganize contents of perf support files.
MIPS: perf: Cleanup formatting in arch/mips/kernel/perf_event.c
MIPS: Add accessor macros for 64-bit performance counter registers.
MIPS: Add probes for more Octeon II CPUs.
MIPS: Add more CPU identifiers for Octeon II CPUs.
MIPS: XLR, XLS: Add comment for smp setup
MIPS: JZ4740: GPIO: Check correct IRQ in demux handler
MIPS: JZ4740: GPIO: Simplify IRQ demuxer
MIPS: JZ4740: Use generic irq chip
MIPS: Alchemy: remove all CONFIG_SOC_AU1??? defines
MIPS: Alchemy: kill au1xxx.h header
MIPS: Alchemy: clean DMA code of CONFIG_SOC_AU1??? defines
MIPS, IDE: Alchem, au1xxx-ide: Remove pb1200/db1200 header dep
MIPS: Alchemy: Redo PCI as platform driver
MIPS: Alchemy: more base address cleanup
MIPS: Alchemy: rewrite USB platform setup.
MIPS: Alchemy: abstract USB block control register access
...
Fix up trivial conflicts in:
arch/mips/alchemy/devboards/db1x00/platform.c
drivers/ide/Kconfig
drivers/mmc/host/au1xmmc.c
drivers/video/Kconfig
sound/mips/Kconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
|
|
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
No longer required
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2705/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/include/asm/mach-au1x00/au1xxx.h
|
|
This patch gets rid of all CONFIG_SOC_AU1XXX defines in
DMA/DBDMA-related code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
au1xxx-ide uses defines from the pb1200/db1200 headers:
get DBDMA ID through platform resource information,
hardcode register spacing. The only 2 users of this driver (and
the only boards it can really work on realiably) use the same
register layout.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-ide@vger.kernel.org
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-ide@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/2716/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
- Rewrite Alchemy PCI support as a platform driver.
- Fixup boards which have PCI.
Run-tested on DB1500 and DB1550.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2706/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/pci.c
delete mode 100644 arch/mips/pci/fixup-au1000.c
delete mode 100644 arch/mips/pci/ops-au1000.c
create mode 100644 arch/mips/pci/pci-alchemy.c
|
|
remove all redundant peripheral base address defines, fix
all affected boards and drivers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Use runtime CPU detection to setup all USB parts.
Remove the Au1200 OTG and UDC platform devices since there are no
drivers for them anyway.
Clean up the USB address mess in the au1000 header.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Alchemy chips have one or more registers which control access
to the usb blocks as well as PHY configuration. I don't want
the OHCI/EHCI glues to know about the different registers and bits;
new code hides the gory details of USB configuration from them.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patchwork: https://patchwork.linux-mips.org/patch/2709/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 drivers/usb/host/alchemy-common.c
|