| Age | Commit message (Collapse) | Author |
|---|
|
Adds extra parameter to AT32 at32_map_usart(), so as to reserve
RTS/CTS/CLK pins.
All boards under arch/avr32/boards have been updated (trivial change), but
not all have been tested.
Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
|
|
Needed to use the atmel-mci driver in an architecture
independant maner.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
at32_reserve_pin now takes an u32 bitmask rather than a single pin.
This allows to reserve multiple pins at once.
Remove (undocumented) SDCS (pin PE26) from reservation in board
setup code.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Add essential system devices, including GPIO controllers, automatically
at core_initcall time. This ensures that the devices are there when the
PIO driver gets initialized at postcore_initcall, fixing a bug exposed
by commit d6634db8fe1784d0a8e4e156970fec034708446e "avr32: Use
platform_driver_probe for pio platform driver".
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Fix a few instances of board code breakage introduced by the atmel-mci
platform interface changes.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
at32_select_periph() now takes an u32 bitmask rather than a single pin.
This allows to set multiple pins at once.
Signed-off-by: Alex Raimondi <mailinglist@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/atmel-mci-2.6.28
|
|
Add the necessary platform infrastructure to support multiple mmc/sdcard
slots all at once through a single controller. Currently, the driver
will use the first valid slot it finds and stick with that, but later
patches will add support for switching between several slots on the fly.
Extend the platform data structure with per-slot information: MMC/SDcard
bus width and card detect/write protect pins. This will affect the pin
muxing as well as the capabilities announced to the mmc core.
Note that board code is now required to supply a mci_platform_data
struct to at32_add_device_mci().
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
This replaces the pin_config param with an u64 pin_mask in
at32_add_device_lcdc, allowing a board-maintainer to indivually select
specific lcdc pins.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Julien May <jmay@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
The #ifdef surrounding the code adding the mmc controller had a typo,
causing it to be compiled even when mmc was supposed to be disabled.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Update all avr32-specific files to use the new platform-specific header
locations. Drivers shared with ARM are left alone for now.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Minor cleanups for the MMC/SD support on avr32:
- Make at32_add_device_mci() properly initialize "missing"
platform data ... so boards like STK1002 won't try GPIO 0.
- Switch over to gpio_is_valid() instead of testing for only
one designated value.
- Provide STK1002 platform data for the unlikely case that
switches are set so first Ethernet controller isn't in use.
(That's the only way to get card detect and writeprotect
switch sensing on the STK1000.)
And get rid of one "unused variable" warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
|
|
This is a driver for the MMC controller on the AP7000 chips from
Atmel. It should in theory work on AT91 systems too with some
tweaking, but since the DMA interface is quite different, it's not
entirely clear if it's worth merging this with the at91_mci driver.
This driver has been around for a while in BSPs and kernel sources
provided by Atmel, but this particular version uses the generic DMA
Engine framework (with the slave extensions) instead of an
avr32-only DMA controller framework.
This driver can also use PIO transfers when no DMA channels are
available, and for transfers where using DMA may be difficult or
impractical for some reason (e.g. the DMA setup overhead is usually
not worth it for very short transfers, and badly aligned buffers or
lengths are difficult to handle.)
Currently, the driver only support PIO transfers. DMA support has been
split out to a separate patch to hopefully make it easier to review.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 3.5 MiB/s on fast cards with debugging disabled.
The driver has also been tested using the mmc_test module on the same
cards. All tests except 7, 9, 15 and 17 succeed. The first two are
unsupported by all the cards I have, so I don't know if the driver
handles this correctly. The last two fail because the hardware flags a
Data CRC Error instead of a Data Timeout error. I'm not sure how to deal
with that.
Documentation for this controller can be found in many data sheets from
Atmel, including the AT32AP7000 data sheet which can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch lets the board code choose which pin out to use for the LCD
interface.
On AT32AP7000 the LCDC is wired to two sets of pins, which lets the user
choose between dual ethernet and 32-bit EBI. For the ATNGW100 board it
is vital to have the choice to select the alternative pinout since this
pinout is routed to the external headers.
Update ATSTK1002 and ATSTK1004 to use the new interface.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
On our custom board we have other oscillator rates than on atngw100 and
atstk100x.
Currently these rates are hardcoded in arch/avr32/mach-at32ap/at32ap700x.c.
This patch moves them into board specific code.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
The ATSTK1006 is basically an upgraded version of ATSTK1002 with
128 MiB SDRAM and 256 MiB NAND flash on board.
Otherwise, the board is very similar to the ATSTK1002, so it uses the
same board support file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
ATSTK1003 and ATSTK1004 are CPU daughterboards for ATSTK1000 featuring
the AT32AP7001 and AT32AP7002 CPUs, respectively.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Reduce the ridiculous amount of #ifdef clutter in atstk1002.c a bit by
moving all the extdac stuff into its own function and providing an
empty stub for the case when it isn't wanted.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
There may be other boards than STK1002 that want to use the leds on
STK1000. Move it to stk1000 common code to make it easier to reuse.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Implement at32_add_device_usba() and use it to wire up the USBA device
on ATSTK1000 and ATNGW100.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Add GPIO led support: J2 to either block of LEDs on the STK1000.
This uses the new LEDS_GPIO driver, and sets up a heartbeat trigger by
default ... either bright (!!) amber, or a more interesting purple.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
The STK1000 uses pullups on the MDIO lines to the PHY, but they are
too weak. This causes the PHY layer to detect PHYs on all possible MII
addresses. Mask out all but the correct address to prevent this from
happening.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
If the user wants to sacrifice macb0 for more GPIOs, let him.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
This adds some STK1002-specific config options covering the jumper settings,
so the kernel can automatically be configured to include the relevant devices.
One of them replaces the previous internal SW2_DEFAULT setting; SPI config
is affected by two of the jumpers; and a fourth one switches between LCD and
the second Ethernet connector. (There's more that to be done.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
In the latest incarnation of the ltv350qv driver the call to
spi_setup() has been removed. So we need to initialize things more
carefully in the board info struct.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
This modifies and extends the existing lcdc platform code to support
the new atmel_lcdfb driver. The ATSTK1000 board code is set up to use
the on-board Samsung LTV350QV LCD panel.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Since the core setup code takes care of both allocation and
reservation of framebuffer memory, there's no need for this board-
specific hook anymore. Replace it with two global variables,
fbmem_start and fbmem_size, which can be used directly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Set up one spi_board_info array per controller and pass this to
at32_add_device_spi so that it can set up any GPIO pins for chip
selects based on this information.
Extracted from a patch by David Brownell and adapted slightly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Move stuff in spi.c into ATSTK1002 board code and update SPI
platform device definitions according to the new GPIO API.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
The PIOE device was left out before because it muxes SDRAM pins (and
is therefore a bit dangerous to mess with) and because no existing
drivers had any use for it.
It is needed for CompactFlash, however, and now that we have a way
to protect the SDRAM pins, it can be safely added.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Fixes to USART setup on the stk-1000 ... don't configure USART 2, since
its TXD/RXD are used for INT-A and INT-B buttons; and configure USART 0
(for IRDA, and with corrected IRQ) iff SW2 has a non-default setting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
The macb driver will probe for the PHY chip and read the mac address
from the MACB registers, so we don't need them in eth_platform_data
anymore.
Since u-boot doesn't currently initialize the MACB registers with the
mac addresses, the tag parsing code is kept but instead of sticking
the information into eth_platform_data, it uses it to initialize
the MACB registers (in case the boot loader didn't do it.) This code
should be unnecessary at some point in the future.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
By moving the ethernet tag parsing to the board-specific code we avoid
the issue of figuring out which device we're supposed to attach the
information to. The board specific code knows this because it's
where the actual devices are instantiated.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Allow the board to remap actual USART peripheral devices to serial
devices by calling at32_map_usart(hw_id, serial_line). This ensures
that even though ATSTK1002 uses USART1 as the first serial port, it
will still have a ttyS0 device.
This also adds a board-specific early setup hook and moves the
at32_setup_serial_console() call there from the platform code.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This adds support for the Atmel AVR32 architecture as well as the AT32AP7000
CPU and the AT32STK1000 development board.
AVR32 is a new high-performance 32-bit RISC microprocessor core, designed for
cost-sensitive embedded applications, with particular emphasis on low power
consumption and high code density. The AVR32 architecture is not binary
compatible with earlier 8-bit AVR architectures.
The AVR32 architecture, including the instruction set, is described by the
AVR32 Architecture Manual, available from
http://www.atmel.com/dyn/resources/prod_documents/doc32000.pdf
The Atmel AT32AP7000 is the first CPU implementing the AVR32 architecture. It
features a 7-stage pipeline, 16KB instruction and data caches and a full
Memory Management Unit. It also comes with a large set of integrated
peripherals, many of which are shared with the AT91 ARM-based controllers from
Atmel.
Full data sheet is available from
http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf
while the CPU core implementation including caches and MMU is documented by
the AVR32 AP Technical Reference, available from
http://www.atmel.com/dyn/resources/prod_documents/doc32001.pdf
Information about the AT32STK1000 development board can be found at
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3918
including a BSP CD image with an earlier version of this patch, development
tools (binaries and source/patches) and a root filesystem image suitable for
booting from SD card.
Alternatively, there's a preliminary "getting started" guide available at
http://avr32linux.org/twiki/bin/view/Main/GettingStarted which provides links
to the sources and patches you will need in order to set up a cross-compiling
environment for avr32-linux.
This patch, as well as the other patches included with the BSP and the
toolchain patches, is actively supported by Atmel Corporation.
[dmccr@us.ibm.com: Fix more pxx_page macro locations]
[bunk@stusta.de: fix `make defconfig']
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
