| Age | Commit message (Collapse) | Author |
|---|
|
commit 1bf6d2c1bb23533af6930581cc39b74685bc29de upstream.
Apparently U8500 U-Boot versions may leave the l2x0 locked down
before executing the kernel. Make sure we unlock it before we
initialize the l2x0. This fixes a performance problem reported
by Jan Rinze.
The l2x0 core has been modified to unlock the l2x0 by default,
but it will not touch the locking registers if the l2x0 was
already enabled, as on the ux500, so we need this quirk to
make sure it is properly turned off.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Adrian Bunk <adrian.bunk@movial.com>
Reported-by: Jan Rinze <janrinze@gmail.com>
Tested-by: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6571534b600b8ca1936ff5630b9e0947f21faf16 upstream.
To configure pads during the initialisation a set of special constants
is used, e.g.
#define MX25_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP)
The problem is that no pull-up/down is getting activated unless both
PAD_CTL_PUE (pull-up enable) and PAD_CTL_PKE (pull/keeper module
enable) set. This is clearly stated in the i.MX25 datasheet and is
confirmed by the measurements on hardware. This leads to some rather
hard to understand bugs such as misdetecting an absent ethernet PHY (a
real bug i had), unstable data transfer etc. This might affect mx25,
mx35, mx50, mx51 and mx53 SoCs.
It's reasonable to expect that if the pullup value is specified, the
intention was to have it actually active, so we implicitly add the
needed bits.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 29a541f6c1f6e4a85628bb86071b9e72c9f8be2c upstream.
Using COHERENT_LINE_{MISS,HIT} for cache misses and references
respectively is completely wrong. Instead, use the L1D events which
are a better and more useful approximation despite ignoring instruction
traffic.
Reported-by: Alasdair Grant <alasdair.grant@arm.com>
Reported-by: Matt Horsnell <matt.horsnell@arm.com>
Reported-by: Michael Williams <michael.williams@arm.com>
Cc: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 002ea9eefec98dada56fd5f8e432a4e8570c2a26 upstream.
The VM subsystem assumes that there are valid memmap entries from
the bank start aligned to MAX_ORDER_NR_PAGES.
On the Ux500 we have a lot of mem=N arguments on the commandline
triggering this bug several times over and causing kernel
oops messages.
Cc: Michael Bohan <mbohan@codeaurora.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Johan Palsson <johan.palsson@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 98e87d57aab9b1594f9cc53a386fcb6f2f2ba6e2 upstream.
This applies ARM errata fix 754322 for all ux500 platforms.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit df77abcafc8dc881b6c9347548651777088e4b27 upstream.
The SMP implementation of __futex_atomic_op clobbers oldval with the
status flag from the exclusive store. This causes it to always read as
zero when performing the FUTEX_OP_CMP_* operation.
This patch updates the ARM __futex_atomic_op implementations to take a
tmp argument, allowing us to store the strex status flag without
overwriting the register containing oldval.
Reported-by: Minho Ban <mhban@samsung.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f630c1bdfbf8fe423325beaf60027cfc7fd7c610 upstream.
This patch implements a workaround for erratum 764369 affecting
Cortex-A9 MPCore with two or more processors (all current revisions).
Under certain timing circumstances, a data cache line maintenance
operation by MVA targeting an Inner Shareable memory region may fail to
proceed up to either the Point of Coherency or to the Point of
Unification of the system. This workaround adds a DSB instruction before
the relevant cache maintenance functions and sets a specific bit in the
diagnostic control register of the SCU.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d8e89b47e00ee80e920761145144640aac4cf71a upstream.
If the attempt to map a page for DMA fails (eg, because we're out of
mapping space) then we must not hold on to the page we allocated for
DMA - doing so will result in a memory leak.
Reported-by: Bryan Phillippe <bp@darkforest.org>
Tested-by: Bryan Phillippe <bp@darkforest.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 72cc205611879525db0374d9831f84f787112b25 upstream.
Commit 980f9f601a "ARM: orion: Consolidate SPI initialization."
broke it by overwriting the SPI0 registration.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 897a6a1a14837d6d582bfd1fd7aba00be44b6469 upstream.
The TNET variant of DaVinci compiles some code that it shares
with other DaVinci variants, however it has a V6 CPU rather than
an ARM926T, thus the hardcoded call to arm926_flush_kern_cache_all()
in sleep.S will obviously fail, and we need to build with the
v6_flush_kern_cache_all() call instead. This was triggered by
manually altering the DaVinci config to build the TNET version.
Cc: Dave Martin <dave.martin@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 810198bc9c109489dfadc57131c5183ce6ad2d7d upstream.
DA850/OMAP-L138 EMAC driver uses random mac address instead of
a fixed one because the mac address is not stuffed into EMAC
platform data.
This patch provides a function which reads the mac address
stored in SPI flash (registered as MTD device) and populates the
EMAC platform data. The function which reads the mac address is
registered as a callback which gets called upon addition of MTD
device.
NOTE: In case the MAC address stored in SPI flash is erased, follow
the instructions at [1] to restore it.
[1] http://processors.wiki.ti.com/index.php/GSG:_OMAP-L138_DVEVM_Additional_Procedures#Restoring_MAC_address_on_SPI_Flash
Modifications in v2:
Guarded registering the mtd_notifier only when MTD is enabled.
Earlier this was handled using mtd_has_partitions() call, but
this has been removed in Linux v3.0.
Modifications in v3:
a. Guarded da850_evm_m25p80_notify_add() function and
da850evm_spi_notifier structure with CONFIG_MTD macros.
b. Renamed da850_evm_register_mtd_user() function to
da850_evm_setup_mac_addr() and removed the struct mtd_notifier
argument to this function.
c. Passed the da850evm_spi_notifier structure to register_mtd_user()
function.
Modifications in v4:
Moved the da850_evm_setup_mac_addr() function within the first
CONFIG_MTD ifdef construct.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bb9ea77846620ed2b37e74c852d72c7a476b248c upstream.
I was intrigued by the fact that the clock stood still on
the Integrator, but it wasn't strange at all, because the
timer was set up all wrong and probably has been for a
while. With this patch the clock starts ticking again:
make the timer periodic (reload), |= on the divisor bit
and load the timer before starting it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 425933b30b0ccfac58065bca6c853ea627443cdf upstream.
iomux-v3.c uses NO_PAD_CTRL as a 32 bit value
so it should not be shifted left by MUX_PAD_CTRL_SHIFT(41)
Previously, anything requesting NO_PAD_CTRL would get
their pad control register set to 0.
Since it is a pad control mask, place it with the other mask values.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 43c734be5571a4daad9f0a3e0b3229a1c0049917 upstream.
This patch fixes L2 Cache size calculations for L2C-210, L2C-310 and
PL310, by changing the L2X0_AUX_CTRL_WAY_SIZE_MASK from 2 bits to 3
bits.
The Auxiliary Control Register for L2C-210, L2C-310 and PL310 has 3bits
[19:17] for Way size, however the existing code only uses 2 bits to
get this value. This results in incorrect cachesize calculations.
It also results in performing operations on the whole cache when we
erroneously decide that the range is big enough (due to l2x0_size being
too small) and also prints incorrect cachesize.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6c7b3ea52e345ab614edb91d3f0e9f3bb3713871 upstream.
While in sleep mode the CS# and other V3020 RTC GPIOs must be driven
high, otherwise V3020 RTC fails to keep the right time in sleep mode.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
davinci: DM365 EVM: fix video input mux bits
ARM: davinci: Check for NULL return from irq_alloc_generic_chip
arm: davinci: Fix low level gpio irq handlers' argument
|
|
Video input mux settings for tvp7002 and imager inputs were swapped.
Comment was correct.
Tested on EVM with tvp7002 input.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: stable@kernel.org
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Avoid NULL dereference of irq_alloc_generic_chip return in low
memory conditions.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: DMA Cleanup as per sparse
ARM: SAMSUNG: Check NULL return from irq_alloc_generic_chip
|
|
Function declaration differs between file: dma.c and file:dma.h
and SPARSE (Documentation/sparse.txt) gives error messages
All dma channels are members of 'enum dma_ch' and not 'unsigned int'
Please have a look at channel definitions in:
arch/arm/mach-s3c64xx/include/mach/dma.h
arch/arm/plat-samsung/include/plat/s3c-dma-pl330.h
arch/arm/mach-s3c2410/include/mach/dma.h
So all arguments should be of type 'enum dma_ch'
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Commit 234b6ceddb4fc2a4bc5b9a7670f070f6e69e0868
clocksource: convert ARM 32-bit up counting clocksources
broke the build for ixp4xx and made big endian operation impossible.
This commit restores the original behaviour.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
[ Thomas says that we might want to have generic BE accessor functions
to the MMIO clock source, but that hasn't happened yet, so in the
meantime this seems to be the short-term fix for the particular
problem - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
pcmcia: pxa2xx/vpac270: free gpios on exist rather than requesting
ARM: pxa/raumfeld: fix device name for codec ak4104
ARM: pxa/raumfeld: display initialisation fixes
ARM: pxa/raumfeld: adapt to upcoming hardware change
ARM: pxa: fix gpio_to_chip() clash with gpiolib namespace
genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
arm: mach-vt8500: add forgotten irq_data conversion
ARM: pxa168: correct nand pmu setting
ARM: pxa910: correct nand pmu setting
ARM: pxa: fix PGSR register address calculation
|
|
Commit 7416401 ("arm: davinci: Fix fallout from generic irq chip
conversion") introduced a bug, causing low level interrupt handlers to
get a bogus irq number as an argument. The gpio irq handler falsely
assumes that the handler data is the irq base number and that is no
longer true.
Set the irq handler data to be a pointer to the corresponding gpio
controller. The chained irq handler can then use it to extract both the
irq base number and the gpio registers structure.
Signed-off-by: Ido Yariv <ido@wizery.com>
CC: Thomas Gleixner <tglx@linutronix.de>
[nsekhar@ti.com: renamed "ctl" to "d", simplified indexing logic for chips and
took care of odd bank handling in irq handler]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into fixes
|
|
In commit f0fba2ad (ASoC: multi-component - ASoC Multi-Component
Support), the name of the ak4104 codec driver was changed without
amending the platform code which uses it as well.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The display requires some milliseconds between GPIO_TFT_VA_EN
and GPIO_DISPLAY_ENABLE. Reorder initialisation to comply with
the display spec.
Also tune timings for better compliance with the spec.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The backlight control is going to change back to PWM in the
upcoming Raumfeld Controller hardware revision.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The PXA platform code has a static inline helper called
gpio_to_chip which clashes with the gpiolib namespace if we
try to expose the function with the same name from gpiolib,
and it's still confusing even if we don't do that. So rename
it to gpio_to_pxachip().
Reported-by: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6994/1: smp_twd: Fix typo in 'twd_timer_rate' printing
ARM: 6987/1: l2x0: fix disabling function to avoid deadlock
ARM: 6966/1: ep93xx: fix inverted RTS/DTR signals on uart1
ARM: 6980/1: mmci: use StartBitErr to detect bad connections
ARM: 6979/1: mach-vt8500: add forgotten irq_data conversion
ARM: move memory layout sanity checking before meminfo initialization
ARM: 6990/1: MAINTAINERS: add entry for ARM PMU profiling and debugging
ARM: 6989/1: perf: do not start the PMU when no events are present
ARM: dmabounce: fix map_single() error return value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C2440: fix section mismatch on mini2440
ARM: S3C24XX: drop return codes in void function of dma.c
ARM: S3C24XX: don't use uninitialized variable in dma.c
ARM: EXYNOS4: Set appropriate I2C device variant
ARM: S5PC100: Fix for compilation error
spi/s3c64xx: Bug fix for SPI with different FIFO level
ARM: SAMSUNG: Add tx_st_done variable
ARM: EXYNOS4: Address a section mismatch w/ suspend issue.
ARM: S5P: Fix bug on init of PWMTimers for HRTimer
ARM: SAMSUNG: header file revised to prevent declaring duplicated
ARM: EXYNOS4: fix improper gpio configuration
ARM: EXYNOS4: Fix card detection for sdhci 0 and 2
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: drop __initdata tags from static struct platform_device declarations
|
|
If mini2440_init() is in __init, mini2440_parse_features() should also
be in __init. Fixes:
(.text+0x9adc): Section mismatch in reference from the function mini2440_parse_features.clone.0() to the
(unknown reference) .init.data:(unknown)
The function mini2440_parse_features.clone.0() references the (unknown reference) __initdata (unknown).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Michel Pollet <buserror@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Commit bb072c3c (ARM / Samsung: Use struct syscore_ops for "core" power
management) turned s3c2410_dma_resume_chan() from int to void. So, drop
the actual return values, too. Fixes:
arch/arm/plat-s3c24xx/dma.c: In function 's3c2410_dma_resume_chan':
arch/arm/plat-s3c24xx/dma.c:1238:3: warning: 'return' with a value, in function returning void
arch/arm/plat-s3c24xx/dma.c:1250:2: warning: 'return' with a value, in function returning void
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Commit 8970ef47 (S3C24XX: Remove hardware specific registers from DMA
calls) removed the parameter dcon in s3c2410_dma_config() and calculates
it on its own. So the debug-output for the old parameter can go, too.
Fixes:
arch/arm/plat-s3c24xx/dma.c: In function 's3c2410_dma_config':
arch/arm/plat-s3c24xx/dma.c:1030:2: warning: 'dcon' is used uninitialized in this function
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This platform has not been converted to 'struct irq_data' when the big
pile was done. It fails to compile nowadays, because the compatibility
code has gone.
CC arch/arm/mach-vt8500/irq.o
arch/arm/mach-vt8500/irq.c:118:2: error: unknown field 'ack' specified in initializer
arch/arm/mach-vt8500/irq.c:118:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:119:2: error: unknown field 'mask' specified in initializer
arch/arm/mach-vt8500/irq.c:119:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:120:2: error: unknown field 'unmask' specified in initializer
arch/arm/mach-vt8500/irq.c:120:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:121:2: error: unknown field 'set_type' specified in initializer
arch/arm/mach-vt8500/irq.c:121:2: warning: initialization from incompatible pointer type
make[1]: *** [arch/arm/mach-vt8500/irq.o] Error 1
Add the missing conversion. Tested on a JayPC-Tablet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alexey Charkov <alchark@gmail.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
To get hundredths of MHz the rate needs to be divided by 10'000.
Here is an example:
twd_timer_rate = 123456789
Before the patch:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 1000000) % 100 = 23
Result: 123.23MHz.
After being fixed:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 10000) % 100 = 45
Result: 123.45MHz.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The l2x0_disable function attempts to writel with the l2x0_lock held.
This results in deadlock when the writel contains an outer_sync call
for the platform since the l2x0_lock is already held by the disable
function. A further problem is that disabling the L2 without flushing it
first can lead to the spin_lock operation becoming visible after the
spin_unlock, causing any subsequent L2 maintenance to deadlock.
This patch replaces the writel with a call to writel_relaxed in the
disabling code and adds a flush before disabling in the control
register, preventing livelock from occurring.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It was discovered by Roberto Bergo, that RTS/DTR signals are inverted after
the boot, because it was causing him problems with hardware controlled modem
connected on ttyAM0. Todd Valentic came with this patch for the issue.
Discussion: http://tech.groups.yahoo.com/group/ts-7000/message/20259
Comments from Petr Štetiar:
Sorry, but forget to add Acked-by[1]:
1. https://patchwork.kernel.org/patch/873052/
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Todd Valentic <todd.valentic@sri.com>
Tested-by: Roberto Bergo <roberto.bergo@robson.it>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This platform has not been converted to 'struct irq_data' when the big
pile was done and fails to compile nowadays. Tested on a JayPC-Tablet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The original pair of <0x01db, 208000000> is invalid. Correct it to
the valid value.
The 6th bit of the NFC APMU register indicates NFC works whether
at 156Mhz or 78Mhz. So 0x19b indicates NFC works at 156Mhz, and
0x1db indicates it works at 78Mhz.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The original pair of <0x01db, 208000000> is invalid.
Correct to the valid value.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The file mfp-pxa2xx.c defines a macro, PGSR(), which translates a gpio
bank number to a PGSR register address. The function pxa2xx_mfp_suspend()
erroneously passed in a gpio number instead of a gpio bank number.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Set up a correct I2C bus controller variant name for Exynos4.
Without this change the I2C bus driver fails to acquire its
clocks.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
|
|
S5PC100 Compilation fails without this patch
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
tx_st_done is required for checking the transmission status of SPI
channels with different fifo levels
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The section mismatch in headsmp.S made hotplug stop working after the
first instance of suspend-to-RAM and its wakeup.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch fixes following.
<6>[ 0.000000] sched_clock: 32 bits at 33MHz, ...
<6>[ 128.651309] Calibrating delay loop...
There is a big jump. The reason is that PWM Timer which
is for HRTimer was used before its initialization.
So this patch changes its order and following is kernel
boot log message after this.
<6>[ 0.000000] sched_clock: 32 bits at 33MHz, ...
<6>[ 0.000088] Calibrating delay loop...
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
