| Age | Commit message (Collapse) | Author |
|---|
|
... for devices. Doing so is a bug, plain and simple, and drives
GregKH round the bend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix compile for h3 MMC
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch removes old platform devices. Alsa should now
be using the ASoC driver. For boards not yet using ASoC,
please see sound/soc/omap/osk5912.c.
Add dummy aic23_power_up and aic23_power_down functions for 770
to keep things compiling.
Remove references to omap_gpio_switch, and unused h2_nand_dev_ready
function.
This patch is based on an earlier patch by Arun KS.
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch enables writing to McBSP Transmit Configuration Control
Register (XCCR) and Receive Configuration Control Register (RCCR)
for 2430/34xx platforms. It also adds XCCR, RCCR entries in McBSP
register configuration structure and bit definitions for both
registers.
If we enable the writing to CCR registers for 2430/34xx and don't
set the default values (setting 0 as a consequence) in ASoC driver,
the Transmit/Receive DMA mode gets disabled and the the
transmission/reception doesn't happen, ending with a
"write error: Input/Output error" when playing with 'aplay'.
Also define dummy CCR registers for omap1.
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Bug in existing code causes synchro control to be set +32 if request
line greater than 63 is used.
Also clean up the function a bit by removing extra parens and
clearing the bits at before write.
Reported by Wenbiao Wang.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There are no wakeup registers on 15xx, and suspend_wakeup
does not exist in the struct gpio_bank.
Without this fix we'll get "arch/arm/plat-omap/gpio.c:1792:
error: 'struct gpio_bank' has no member named 'suspend_wakeup'"
as noted by Russell King.
Note that the ifdefs will be cleaned up once the omap gpio
code gets split into omap1 and omap2 specific parts.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix compile by removing remaining omap specific gpio
calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch
to do this with gpio_keys.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
pxa, s3c
arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move otg_get/set/put_transceiver() from omap specific code
to common otg.c so other upcoming drivers can share them.
[ dbrownell@users.sourceforge.net: move to drivers/usb/otg, dox ]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
As Russell King points out, calling put_device(otg_transceiver->dev)
directly in driver cleanup paths makes assumptions about otg_transceiver
internals.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel
|
|
Add low-level initialization for hsmmc controller. Merged into
this patch patch are various improvments and board support by
Grazvydas Ignotas and David Brownell.
Also change wire4 to be wires, as some newer controllers support
8 data lines.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This will simplify the MMC low-level init, and make it more
flexible to add support for a newer MMC controller in the
following patches.
The patch rearranges platform data and gets rid of slot vs
controller confusion in the old data structures. Also fix
device id numbering in the clock code.
Some code snippets are based on an earlier patch by
Russell King <linux@arm.linux.org.uk>.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds some new pin multiplexing options
for McBSP and McSPI from Arun KS. Also add two more
GPIOs from David Brownell.
Also mark omap24xx_cfg_reg() static.
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
SDMA channel is not disabled after transaction error. So explicitly disable it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked By : Nishant kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add Ethernet device support in board-ldp.c to make ldp can boot and mount
nfs successfully.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
|
|
- Simplify function omap_i2c_mux_pins
- Add OMAP34xx pin multiplexing for busses 1 - 3
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The GPTIMER TLDR register does not need to be written if the GPTIMER
is not in autoreload mode. This is the usual case for dynamic tick-enabled
kernels.
Simulation data indicate that skipping the read that occurs as part of
the write should save at least 300-320 ns for each GPTIMER1 timer
reprogram. (This assumes L4-Wakeup is at 19MHz and GPTIMER write
posting is enabled.) Skipping the write itself probably won't have
much impact since it should be posted on the OCP interconnect.
Tested on 2430SDP and 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
omap_dm_timer_write_reg() already waits for pending writes to complete,
so the extra wait in omap_dm_timer_set_load() is superfluous.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
system_rev is meant for board revision, this patch changes
all relevant instances to use the new omap_rev() function
liberating system_rev to be used with ATAG_REVISION as it
has been designed.
Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
At some point omap2 changed the bits for GET_OMAP_CLASS, which
broke 15xx detection on 730 as noticed by Russell King.
This patch fixes omap2 cpu detection to respect the original
GET_OMAP_CLASS, and simplifies the detection for 34xx.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Switch to gpio_request/free calls
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Minor GPIO fixes:
- If get_gpio_bank() fails, then BUG() out.
- In omap_set_gpio_debounce():
* protect the read/modify/write with the relevant spinlock
* make the omap3 clock ops pass "sparse" checking
Except for the spinlock problem, these were reported through "make".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Clean up OMAP GPIO request/free functions
- Rename and declare static OMAP specific GPIO request/free functions
- Register them into gpiolib as chip-specific hooks
- Add omap_request_gpio/omap_free_gpio wrappers for existing code not
converted yet to use gpiolib
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
[ dbrownell@users.sourceforge.net: remove needless check_gpio() calls ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Have most uses of OMAP_GPIO_IRQ() use gpio_to_irq() instead.
Calls used for table initialization are left alone, at least
this time around.
(This patch is for code in both the OMAP tree and mainline.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
More conversion to the standard GPIO interfaces: stop using
omap_set_gpio_direction() entirely, and switch over to the
gpio_direction_output() call.
Note that because gpio_direction_output() includes the initial
value, this change isn't quite transparent.
- For the call sites which defined an initial value either
before or after setting the direction, that value was used.
When that value was previously assigned afterwards, this
could eliminate a brief output glitch ... and possibly
change behavior. In a few cases (LCDs) several values
were assigned together ... those were re-arranged to match
the explicit sequence provided.
- Some call sites didn't define such a value; so I chose an
initial "off/reset" value that seemed to default to "off".
In short, files touched by this patch might notice some small
changes in startup behavior (with trivial fixes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.
The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.
Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script. Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Make OMAP use the new __gpio_to_irq() hook, to make it easier to
support IRQs coming in from off-chip gpio controllers like the
TWL4030/TPS65930 chip used on OMAP3 boads like Beagleboard.org and
the Gumstix Overo.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There are already various drivers having bigger label than 10 bytes. Most
of them fit well under 20 bytes but make column width exact so that
oversized labels don't mess up output alignment.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch changes gpio "driver" to enable debounce clock for
gpio-bank only when debounce is enabled for some gpio in that bank.
Gpio functional clocks are also renamed in clock tree, gpioX_fck ->
gpioX_dbck.
This patch triggers problem with gpio wake-up and Omap3. Gpios in PER
domain aren't capable to generate wake-up if PER domain is in sleep
state. For this iopad wake-up should be used and needed pad
configuration should be done. Enabling iopad wake-up for gpio pads is
left for bootloader or omap mux configuration in kernel.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes a number of sillies, from missing 'const' to using
'return' in void functions, to functions with no arguments not even
'void' and a cast which isn't required.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
As Al did for Versatile in 2ad4f86b60b649fd7428265c08d73a3bd360c81b,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
arch/arm/mach-clps7500/include/mach/memory.h
|
|
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than:
config CPU_BLAH
bool
depends on ARCH_FOO || MACH_BAR
default y if ARCH_FOO || MACH_BAR
arrange for ARCH_FOO and MACH_BAR to select CPU_BLAH directly.
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Brian Swetland <swetland@google.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use the correct wake-up enable register, and make it
work with 34xx also.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The second clk_deny_idle instance should be clk_allow_idle instead.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise twl4030 gpios won't work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On omap24xx, INTCPS_SIR_IRQ_OFFSET bits [6:0] contains the current
active interrupt number.
However, on 34xx INTCPS_SIR_IRQ_OFFSET bits [31:7] also contains the
SPURIOUSIRQFLAG, which gets set if the interrupt sorting information
is invalid.
If the SPURIOUSIRQFLAG bits are not ignored, the interrupt code will
occasionally produce a bunch of confusing errors:
irq -33, desc: c02ddcc8, depth: 0, count: 0, unhandled: 0
->handle_irq(): c006f23c, handle_bad_irq+0x0/0x22c
->chip(): 00000000, 0x0
->action(): 00000000
Fix this by masking out only the ACTIVEIRQ bits. Also fix a
confusing comment.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
debugfs_create_*() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Comparing to PATCH v1, because clk_debugfs_init is included in
"#if defined CONFIG_DEBUG_FS", we only need to check NULL return.
Thanks Li Zefan <lizf@cn.fujitsu.com>
debugfs_create_u8() and other function's return value's checking method are
also fixed in this patch.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
* git://git.infradead.org/mtd-2.6: (69 commits)
Revert "[MTD] m25p80.c code cleanup"
[MTD] [NAND] GPIO driver depends on ARM... for now.
[MTD] [NAND] sh_flctl: fix compile error
[MTD] [NOR] AT49BV6416 has swapped erase regions
[MTD] [NAND] GPIO NAND flash driver
[MTD] cmdlineparts documentation change - explain where mtd-id comes from
[MTD] cfi_cmdset_0002.c: Add Macronix CFI V1.0 TopBottom detection
[MTD] [NAND] Fix compilation warnings in drivers/mtd/nand/cs553x_nand.c
[JFFS2] Write buffer offset adjustment for NOR-ECC (Sibley) flash
[MTD] mtdoops: Fix a bug where block may not be erased
[MTD] mtdoops: Add a magic number to logged kernel oops
[MTD] mtdoops: Fix an off by one error
[JFFS2] Correct parameter names of jffs2_compress() in comments
[MTD] [NAND] sh_flctl: add support for Renesas SuperH FLCTL
[MTD] [NAND] Bug on atmel_nand HW ECC : OOB info not correctly written
[MTD] [MAPS] Remove unused variable after ROM API cleanup.
[MTD] m25p80.c extended jedec support (v2)
[MTD] remove unused mtd parameter in of_mtd_parse_partitions()
[MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGE
[MTD] [NAND] driver extension to support NAND on TQM85xx modules
...
|
|
Conflicts:
arch/arm/mach-versatile/core.c
|
|
Conflicts:
arch/arm/mach-versatile/core.c
|
|
Conflicts:
arch/arm/mach-omap2/gpmc.c
arch/arm/mach-omap2/irq.c
|
|
With the upcoming WDT patches OMAP_WDT_BASE is no longer needed
in devices.c. Revert some earlier omap3 changes to avoid merge
conflicts with the WDT patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Recent McBSP patches changed to allocating devices dynamically
and the check for OMAP_MAX_MCBSP_COUNT became unnecessary.
The check for OMAP_MAX_MCBSP_COUNT should have been removed with
the earlier McBSP patches in devices.c but was accidentally left
out.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
