aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/mach-pxa/include
AgeCommit message (Collapse)Author
2012-05-18Merge branch 'board-specific' of git://github.com/hzhuang1/linux into ↵Olof Johansson
next/boards * 'board-specific' of git://github.com/hzhuang1/linux: ARM: pxa: hx4700: Add Synaptics NavPoint touchpad ARM: pxa: Use REGULATOR_SUPPLY macro
2012-05-14ARM: pxa: hx4700: Add Synaptics NavPoint touchpadPaul Parsons
This patch adds the Synaptics NavPoint touchpad to the hx4700 platform: 1. Change GPIO23_SSP1_SCLK value in hx4700_pin_config[] from an output to an input, since the NavPoint is connected to SSP in SPI slave mode. 2. Add GPIO102_GPIO (NavPoint power) to hx4700_pin_config[]. 3. Add navpoint platform_device to devices[]. Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
2012-05-10Merge tag 'omap-board-for-v3.5' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards Board specific changes for omap. Note that these are based on omap-pm-regulator-for-v3.5 as both branches are adding twl regulators. By Paul Gortmaker (8) and others via Linus Torvalds (38) and others * tag 'omap-board-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: OMAP: omap4panda: Use common configuration for V1V8, V2V1 supplies OMAP: 4430SDP: Use common configuration for V1V8, V2V1 supplies OMAP4: twl-common: Add twl6030 V1V8, V2V1 SMPS common configuration ARM: OMAP: Mark Beagleboard-xM MMC bus as 4-bit Add MSUB support for the LogicPD OMAP3530 DevKits ARM: OMAP: rx51: Platform support for lis3lv02d accelerometer ARM: OMAP2+: craneboard: register emac device ARM: OMAP4: board-omap4panda: Register platform device for HDMI audio codec ARM: OMAP4: board-4430sdp: Register platform device for HDMI audio codec ARM: OMAP: devices: Register platform devices for HDMI audio ARM: OMAP3: igep0020: Add support for Micron NAND Flash storage memory ARM: OMAP2+: nand: Make board_onenand_init() visible to board code ARM: OMAP3: cm-t35: add support for power off ARM: OMAP: WiLink platform data for the PandaBoard ARM: OMAP2PLUS: Enable HIGHMEM ARM: OMAP: omap2plus_defconfig: Enable ehci-omap and sms95xx support Signed-off-by: Olof Johansson <olof@lixom.net>
2012-04-27ARM: pxa: mioa701 add camera output enable gpioRobert Jarzmik
The Micron MT9M111 camera chip needs its output enable to be activated in order to work. The bootloader is not required to activate it, so do it in machine code. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
2012-04-27ARM: pxa: use ioremap to access CPLDSascha Hauer
The pcm990 baseboard for the pcm027 module used to setup a static mapping for accessing the CPLD. It became illegal to call iotable_init that late. The pcm027 support is broken since then. This patch switches the cpld support to ioremap and removes all references to previous static mappings. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
2012-04-27ARM: PXA2xx: MFP: fix bug with MFP_LPM_KEEP_OUTPUTIgor Grinberg
Pins that have MFP_LPM_KEEP_OUTPUT set and are configured for output must retain the output state in low power mode. Currently, the pin direction configuration is overrided with values in gpdr_lpm[] array and do not obey the MFP_LPM_KEEP_OUTPUT setting. Fix the above bug and add some documentation to clarify the MFP_LPM_KEEP_OUTPUT setting purpose. Reported-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
2012-04-05ARM: fix __io macro for PCMCIARob Herring
With commit c334bc1 (ARM: make mach/io.h include optional), PCMCIA was broken. PCMCIA depends on __io() returning a valid i/o address, and most ARM platforms require IO_SPACE_LIMIT be set to 0xffffffff for PCMCIA. This needs a better fix with a fixed i/o address mapping, but for now we just restore things to the previous behavior. This fixes at91, omap1, pxa and sa11xx. pxa needs io.h if PCI is enabled, but PCMCIA is not. sa11xx already has IO_SPACE_LIMIT set to 0xffffffff, so it doesn't need an io.h. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Joachim Eastwood <joachim.eastwood@jotron.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Andrew Victor <linux@maxim.org.za> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Tested-by: Paul Parsons <lost.distance@yahoo.com> (pxa270) Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2012-03-29Merge tag 'cleanup2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull "ARM: cleanups of io includes" from Olof Johansson: "Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes, moving some of the oft-repeated macros to a common location and removing a bunch of boiler plate. This is another step closer to a common zImage for multiple platforms." Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes around it, tegra localtimer.o is *still* gone, yadda-yadda). * tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits) ARM: tegra: Include assembler.h in sleep.S to fix build break ARM: pxa: use common IOMEM definition ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol ARM: __io abuse cleanup ARM: create a common IOMEM definition ARM: iop13xx: fix missing declaration of iop13xx_init_early ARM: fix ioremap/iounmap for !CONFIG_MMU ARM: kill off __mem_pci ARM: remove bunch of now unused mach/io.h files ARM: make mach/io.h include optional ARM: clps711x: remove unneeded include of mach/io.h ARM: dove: add explicit include of dove.h to addr-map.c ARM: at91: add explicit include of hardware.h to uncompressor ARM: ep93xx: clean-up mach/io.h ARM: tegra: clean-up mach/io.h ARM: orion5x: clean-up mach/io.h ARM: davinci: remove unneeded mach/io.h include [media] davinci: remove includes of mach/io.h ARM: OMAP: Remove remaining includes for mach/io.h ARM: msm: clean-up mach/io.h ...
2012-03-29Merge branch 'for-linus' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull more ARM updates from Russell King. This got a fair number of conflicts with the <asm/system.h> split, but also with some other sparse-irq and header file include cleanups. They all looked pretty trivial, though. * 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits) ARM: fix Kconfig warning for HAVE_BPF_JIT ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds ARM: 7349/1: integrator: convert to sparse irqs ARM: 7259/3: net: JIT compiler for packet filters ARM: 7334/1: add jump label support ARM: 7333/2: jump label: detect %c support for ARM ARM: 7338/1: add support for early console output via semihosting ARM: use set_current_blocked() and block_sigmask() ARM: exec: remove redundant set_fs(USER_DS) ARM: 7332/1: extract out code patch function from kprobes ARM: 7331/1: extract out insn generation code from ftrace ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format ARM: 7351/1: ftrace: remove useless memory checks ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path ARM: Versatile Express: add NO_IOPORT ARM: get rid of asm/irq.h in asm/prom.h ARM: 7319/1: Print debug info for SIGBUS in user faults ARM: 7318/1: gic: refactor irq_start assignment ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop ARM: 7315/1: perf: add support for the Cortex-A7 PMU ...
2012-03-27Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson: "These changes are all specific to one board only. We're trying to keep the number of board files low, but generally board level updates are ok on platforms that are working on moving towards DT based probing, which will eventually lead to removing them. The board-ams-delta.c board file gets a conflict between the removal of ams_delta_config and the addition of a lot of other data. The Kconfig file has two changes in the same line, and in exynos, the power domain cleanup conflicts with the addition of the image sensor device. Signed-off-by: Arnd Bergmann <arnd@arndb.de> [olof: Amended a fix for a mismerge to board-omap4panda.c] Signed-off-by: Olof Johansson <olof@lixom.net>" Fixed up some fairly trivial conflicts manually. * tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits) i.MX35-PDK: Add Camera support ARM : mx35: 3ds-board: add framebuffer device pxa/hx4700: Remove pcmcia platform_device structure ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35% ARM: pxa/hx4700: Remove unwanted request for GPIO105 ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board ARM: EXYNOS: Register JPEG on nuri ARM: EXYNOS: Register JPEG on universal_c210 ARM: S5PV210: Enable JPEG on SMDKV210 ARM: S5PV210: Add JPEG board definition ARM: EXYNOS: Enable JPEG on Origen ARM: EXYNOS: Enable JPEG on SMDKV310 ARM: EXYNOS: Add __init attribute to universal_camera_init() ARM: EXYNOS: Add __init attribute to nuri_camera_init() ARM: S5PV210: Enable FIMC on SMDKC110 ARM: S5PV210: Enable FIMC on SMDKV210 ARM: S5PV210: Enable MFC on SMDKC110 ARM: S5PV210: Enable MFC on SMDKV210 ARM: EXYNOS: Enable G2D on SMDKV310 ARM: tegra: update defconfig ...
2012-03-25ARM: pxa: use common IOMEM definitionRob Herring
pxa was missed in the moving of IOMEM to a common definition, so lots of IOMEM redefined warnings were introduced. So remove pxa IOMEM definition and fix all the fallout. Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Haojian Zhuang <haojian.zhuang@marvell.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.de> Cc: rtc-linux@googlegroups.com Cc: alsa-devel@alsa-project.org
2012-03-25ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbolRob Herring
The only users of ARCH_HAS_DMA_SET_COHERENT_MASK are 2 ARM platforms: ixp4xx and pxa cm_x2xx. We've been getting lucky that the define is implicitly included before dma-mapping.h, but the removal of io.h broke things (c334bc1 ARM: make mach/io.h include optional). Since memory.h is the correct place, but no longer exists, convert the define to a kconfig entry. Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Nicolas Pitre <nico@linaro.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Krzysztof Halasa <khc@pm.waw.pl> Cc: Eric Miao <eric.y.miao@gmail.com> Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Dan Williams <dan.j.williams@intel.com>
2012-03-23Merge branch 'pcmcia' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull #3 ARM updates from Russell King: "This adds gpio support to soc_common, allowing an amount of code to be deleted from each PCMCIA socket driver for the PXA/SA11x0 SoCs." * 'pcmcia' of git://git.linaro.org/people/rmk/linux-arm: PCMCIA: sa1111: rename sa1111 socket drivers to have sa1111_ prefix. PCMCIA: make lubbock socket driver part of sa1111_cs PCMCIA: add Kconfig control for building sa11xx_base.c PCMCIA: sa1111: jornada720: no need to disable IRQs around sa1111_set_io PCMCIA: sa1111: pass along sa1111_pcmcia_configure_socket() failure code PCMCIA: soc_common: remove explicit wrprot initialization in socket drivers PCMCIA: soc_common: remove soc_pcmcia_*_irqs functions PCMCIA: sa11x0: h3600: convert to use new irq/gpio management PCMCIA: sa11x0: simpad: convert to use new irq/gpio management PCMCIA: sa11x0: shannon: convert to use new irq/gpio management PCMCIA: sa11x0: nanoengine: convert reset handling to use GPIO subsystem PCMCIA: sa11x0: nanoengine: convert to use new irq/gpio management PCMCIA: sa11x0: cerf: convert reset handling to use GPIO subsystem PCMCIA: sa11x0: cerf: convert to use new irq/gpio management PCMCIA: sa11x0: assabet: convert to use new irq/gpio management PCMCIA: sa1111: use new per-socket irq/gpio infrastructure PCMCIA: pxa: convert PXA socket drivers to use new irq/gpio management PCMCIA: soc_common: add GPIO support for card status signals PCMCIA: soc_common: move common initialization into soc_common
2012-03-15Merge branch 'board-specific' of git://github.com/hzhuang1/linux into ↵Arnd Bergmann
next/boards * 'board-specific' of git://github.com/hzhuang1/linux: pxa/hx4700: Remove pcmcia platform_device structure ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35% ARM: pxa/hx4700: Remove unwanted request for GPIO105 (update to 3.3-rc7) Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-14ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%Paul Parsons
Drive the two Bluetooth UART output GPIOs (GPIO43_BTUART_TXD, GPIO45_BTUART_RTS) LOW during sleep mode instead of HIGH. This reduces sleep mode battery discharge from approximately 46 mA to approximately 30 mA. Signed-off-by: Oliver Winker <oliver@oli1170.net> Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
2012-03-06ARM: remove bunch of now unused mach/io.h filesRob Herring
Now that many platforms don't need mach/io.h, remove the unused ones. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Pawel Moll <pawel.moll@arm.com> Acked-by: Nicolas Pitre <nico@linaro.org>
2012-02-23ARM: 7344/1: pxa: mainstone: add missing include for IRQ_BOARD_STARTRob Herring
As part of mach/irqs.h include removal from sparse, mainstone.h was missed. This fixes the compile of the pcmcia driver. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-02-22Merge branch 'entry-macro-cleanup' of git://sources.calxeda.com/kernel/linux ↵Russell King
into for-armsoc
2012-02-21ARM: remove disable_fiq and arch_ret_to_user macrosRob Herring
Now that most platforms don't need disable_fiq and arch_ret_to_user macros, we can remove the empty macros or empty entry-macro.S files. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Ryan Mallon <rmallon@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Shawn Guo <shawn.guo@linaro.org>
2012-02-04PCMCIA: pxa: convert PXA socket drivers to use new irq/gpio managementRussell King
Convert all the PXA platform socket drivers to use the new irq/gpio management provided by soc_common. This relieves these drivers from having to do anything with these GPIOs other than provide the numbers to soc_common. Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-02-04Merge branch 'sparse_irq' of git://sources.calxeda.com/kernel/linux into ↵Russell King
devel-stable
2012-01-25ARM: pxa: remove NR_IRQSRob Herring
Remove NR_IRQS and add a per machine .nr_irqs setting. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-01-20ARM: big removal of now unused arch_idle()Nicolas Pitre
When this is the only content remaining in mach/system.h then the whole file is removed. Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: David Brown <davidb@codeaurora.org> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-09Merge branch 'samsung/driver' into next/driversArnd Bergmann
Conflicts: arch/arm/mach-mxs/include/mach/common.h Pull in previous samsung conflict merges and do a trivial merge of an mxs double-add conflict. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-01-05Merge branch 'restart' into for-linusRussell King
Conflicts: arch/arm/mach-exynos/cpu.c The changes to arch/arm/mach-exynos/cpu.c were moved to mach-exynos/common.c.
2012-01-05ARM: restart: remove the now empty arch_reset()Russell King
Remove the now empty arch_reset() from all the mach/system.h includes, and remove its callsite. Remove arm_machine_restart() as this function no longer does anything useful. For samsung platforms, remove the include of mach/system-reset.h and plat/system-reset.h from their respective mach/system.h headers as these just define their arch_reset functions. As a result, the s3c2410 and plat-samsung system-reset.h files are no longer referenced, so remove these files entirely. Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-01-05ARM: restart: pxa: use new restart hookRussell King
Hook these platforms restart code into the new restart hook rather than using arch_reset(). Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-12-06Merge branch 'mxs/saif' into next/driversArnd Bergmann
Conflicts: drivers/net/ethernet/cadence/Kconfig
2011-12-05Merge branch 'vmalloc' of git://git.linaro.org/people/nico/linux into ↵Russell King
devel-stable
2011-12-05Merge branch 'for-rmk' of ↵Russell King
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into devel-stable Conflicts: arch/arm/common/gic.c arch/arm/plat-omap/include/plat/common.h
2011-11-26ARM: big removal of now unused vmalloc.h filesNicolas Pitre
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
2011-11-15ARM: Make global handler and CONFIG_MULTI_IRQ_HANDLER mutually exclusiveMarc Zyngier
Even when CONFIG_MULTI_IRQ_HANDLER is selected, the core code requires the arch_irq_handler_default macro to be defined as a fallback. It turns out nobody is using that particular feature as both PXA and shmobile have all their machine descriptors populated with the interrupt handler, leaving unused code (or empty macros) in their entry-macro.S file just to be able to compile entry-armv.S. Make CONFIG_MULTI_IRQ_HANDLER exclusive wrt arch_irq_handler_default, which allows to remove one test from the hot path. Also cleanup both PXA and shmobile entry-macro.S. Cc: Paul Mundt <lethal@linux-sh.org> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Eric Miao <eric.y.miao@gmail.com> Tested-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2011-11-15ARM: pxa: change gpio to platform deviceHaojian Zhuang
Remove most gpio macros and change gpio driver to platform driver. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
2011-11-14ARM: pxa: rename NR_BUILTIN_GPIOHaojian Zhuang
NR_BUILTIN_GPIO is both defined in arch-pxa and arch-mmp. Now replace it with PXA_NR_BUILTIN_GPIO and MMP_NR_BUILTIN_GPIO. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
2011-11-14ARM: pxa: rename gpio_to_irq and irq_to_gpioHaojian Zhuang
Avoid to define gpio_to_irq() and irq_to_gpio() for potential name confliction since multiple architecture will be built together. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
2011-11-14ARM: pxa: use chained interrupt for GPIO0 and GPIO1Haojian Zhuang
GPIO0 and GPIO1 are linked to unique interrupt line in PXA series, others are linked to another interrupt line. All GPIO are linked to one interrupt line in MMP series. Since gpio driver is shared between PXA series and MMP series, define GPIO0 and GPIO1 as chained interrupt chip. So we can move out gpio code from irq.c to gpio-pxa.c. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>
2011-11-14ARM: pxa: rename IRQ_GPIO to PXA_GPIO_TO_IRQHaojian Zhuang
Avoid potential naming confliction since multiple architecture will be built in a single kernel. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>
2011-11-10ARM: pxa: fix inconsistent CONFIG_USB_PXA27XHaojian Zhuang
Since CONFIG_USB_GADGET_PXA27X and other macros are renamed to CONFIG_USB_PXA27X. Update them in arch/arm/mach-pxa and arch/arm/configs to keep consistent. Cc: stable@kernel.org Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-11-05ARM: PXA: fix gpio-pxa.h build errorsRussell King
A mismerge in 43872fa (Merge branch 'depends/rmk/gpio' into next/fixes) causes these build errors: In file included from arch/arm/mach-pxa/include/mach/gpio.h:30, from arch/arm/include/asm/gpio.h:6, from include/linux/gpio.h:31, from arch/arm/mach-pxa/generic.c:20: arch/arm/mach-pxa/include/mach/gpio-pxa.h: In function ■__gpio_is_occupied■: arch/arm/mach-pxa/include/mach/gpio-pxa.h:121: error: invalid operands to binary >> (have ■void *■ and ■unsigned int■) arch/arm/mach-pxa/include/mach/gpio-pxa.h:122: error: invalid operands to binary & (have ■void *■ and ■int■) arch/arm/mach-pxa/include/mach/gpio-pxa.h:129: error: invalid operands to binary & (have ■void *■ and ■int■) So fix them. Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-11-01Merge branch 'depends/rmk/memory_h' into next/fixesArnd Bergmann
Fix up all conflicts between the memory.h cleanup and bug fixes. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-10-31Merge branch 'depends/rmk/gpio' into next/fixesArnd Bergmann
This sorts out merge conflicts with the arm/gpio branch that already got merged into mainline Linux. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-10-13ARM: mach-pxa: remove mach/memory.hNicolas Pitre
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
2011-10-08ARM: pxa: use correct __iomem annotationsArnd Bergmann
This tries to clear up the confusion between integers and iomem pointers in the marvell pxa platform. MMIO addresses are supposed to be __iomem* values, in order to let the Linux type checking work correctly. This patch moves the cast to __iomem as far back as possible, to the place where the MMIO virtual address windows are defined. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-10-08ARM: pxa: make pxafb_smart_*() empty when not enabledEric Miao
Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-10-08ARM: pxa: pxa95x/saarb depends on pxa3xx codeEric Miao
saarb uses pxa3xx_map_io and pxa3xx_handle_irq, which are part of the pxa3xx code. This makes sure the necessary header and implementation is used when building the board file. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-10-08ARM: pxa: make zylonite_pxa*_init declaration match codeArnd Bergmann
When support for zylonite is disabled, the zylonite_pxa300_init and zylonite_pxa320_init functions are not there, but the declaration is still kept around if any other boards for the same soc are enabled. This changes the declaration to be conditional on the same symbol as the code. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-10-08ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer availableEric Miao
Cc: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-10-07ARM: pxa: fix building error by palm27x_lcd_init() when FB_PXA not definedEric Miao
Cc: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-10-01ARM: 7104/1: plat-pxa: break out GPIO driver specificsLinus Walleij
The <mach/gpio.h> file is included from upper directories and deal with generic GPIO and gpiolib stuff. Break out the platform and driver specific defines and functions into its own header file. Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-09-26ARM: add an extra temp register to the low level debugging addruart macroNicolas Pitre
Some platforms (like OMAP not to name it) are doing rather complicated hacks just to determine the base UART address to use. Let's give their addruart macro some slack by providing an extra work register which will allow for much needed cleanups. This is basically a no-op as this commit is only adding the extra argument to the macro but no one is using it yet. Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org> Reviewed-by: Kevin Hilman <khilman@ti.com>