| Age | Commit message (Collapse) | Author |
|---|
|
OMAP4 has module specific context lost registers which makes it now
possible to have module level context loss count, instead of relying
on the powerdomain level context count.
Add 2 private hwmod api's to update/clear the hwmod/module specific
context lost counters/register.
Update the module specific context_lost_counter and clear the hardware
bits just after enabling the module.
omap_hwmod_get_context_loss_count() now returns the hwmod context loss
count them on platforms where they exist (OMAP4), else fall back on
the pwrdm level counters for older platforms.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added function kerneldoc, fixed structure kerneldoc,
rearranged structure to avoid memory waste, marked fns as OMAP4-specific,
prevent fn entry on non-OMAP4 chips, reduced indentation, merged update
and clear, merged patches]
[t-kristo@ti.com: added support for arch specific hwmod ops, and changed
the no context offset indicator to USHRT_MAX]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: use NO_CONTEXT_LOSS_BIT flag rather than USHRT_MAX;
convert unsigned context lost counter to int to match the return type;
get rid of hwmod_ops in favor of the existing soc_ops mechanism;
move context loss low-level accesses to the PRM code]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Consolidate all of the copies of MAX_MODULE_HARDRESET_WAIT and
MAX_MODULE_SOFTRESET_WAIT into one place, arch/arm/mach-omap2/prm.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
|
|
Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks. This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.
At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
|
|
The OMAP watchdog timer driver needs to determine what caused the SoC
to reset for its GETBOOTSTATUS ioctl. So, define a set of standard
reset sources across OMAP SoCs. For OMAP2xxx, 3xxx, and 4xxx SoCs,
define mappings from the SoC-specific reset source register bits to
the standardized reset source IDs. Create SoC-specific PRM functions
that read the appropriate per-SoC register and use the mapping to
return the standardized reset bits. Register the SoC-specific PRM
functions with the common PRM code via prm_register(). Create a
function in the common PRM code, prm_read_reset_sources(), that
calls the SoC-specific function, registered during boot.
This patch does not yet handle some SoCs, such as AM33xx. Those SoCs
were not handled by the code this will replace.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
There are several PRM operations which behave similarly across OMAP2+
SoCs, but which have slight differences in their underlying
implementations. For example, to fetch the SoC's last reset sources,
different registers are read across OMAP2xxx, 3xxx, and 44xx, and
different bits are used on each SoC. But the information returned is
so similar that a single, common interface for drivers is useful.
This patch creates the support code for this function pointer
registration process. No function pointers are included yet, but a
subsequent patch will create one for the reset source API.
To illustrate the end goal with the above reset source example, each
per-SoC driver will use its own low-level implementation function --
e.g., prm2xxx.c would contain omap2xxx_prm_read_reset_sources(). This
function would read the appropriate register and remap the register
bits to a standard set of reset source bits. When the prm2xxx.c
driver is loaded, it would register this function with the common PRM
driver, prm.c. prm.c would then export a common function,
omap_prm_read_reset_sources(). Calling it would call through to the
function pointer for the currently-registered SoC PRM driver. This
will allow other drivers to use PRM-provided data and operations
without needing to know which SoC is currently in use.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
In preparation for adding OMAP4-specific PRCM accessor/mutator
functions, split the existing OMAP2/3 PRCM code into OMAP2/3-specific
files. Most of what was in mach-omap2/{cm,prm}.{c,h} has now been
moved into mach-omap2/{cm,prm}2xxx_3xxx.{c,h}, since it was
OMAP2xxx/3xxx-specific.
This process also requires the #includes in each of these files to be
changed to reference the new file name. As part of doing so, add some
comments into plat-omap/sram.c and plat-omap/mcbsp.c, which use
"sideways includes", to indicate that these users of the PRM/CM includes
should not be doing so.
Thanks to Felipe Contreras <felipe.contreras@gmail.com> for comments on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Split the existing cm44xx.h file into cm1_44xx.h and cm2_44xx.h files
so they match their underlying OMAP hardware modules. Add clockdomain
offset information.
Add header files for the MPU local PRCM, prcm_mpu44xx.h, and for the
SCRM, scrm44xx.h. SCRM register offsets still need to be added; TI
should do this.
Move the "_MOD" macros out of the prcm-common.h header file, into the
header file of the hardware module that they belong to. For example,
OMAP4430_PRM_*_MOD macros have been moved into the prm44xx.h header.
Adjust #includes of all files that used the old PRCM header file names
to point to the new filenames.
The autogeneration scripts have been updated accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
This patch adds hard-reset support for processor modules (e.g., DSP, IVA)
on OMAP2/3 platforms. It's based on the OMAP4 hard-reset support that Benoît
developed in the previous patch.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
Most processor modules (e.g., DSP, IVA, IPU) on OMAPs can be reset
under the control of the PRM. This patch adds an API for this purpose
for OMAP4 devices:
int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift);
This API is intended to be used only by the hwmod code - a subsequent
patch will add that support to hwmod.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
The MPU subsystem was named based on internal code name (CHIRON).
This patch will remove all the occurences of the chiron name
are replace it with PRCM_MPU in order to differentiate
the MPU local PRCM to the global one.
Remove PDA_ from PRCM_MPU registers names to stick to the global
PRM naming convention.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
|
|
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them. This makes the use of these
macros consistent. It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Module offsets were same for OMAP2 and OMAP3 while they differ for OMAP4.
Hence we need different macros for identifying platform specific offsets.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
|
|
The CHIRONSS has its own local PRCM module and the register defines
need to use the CHIRONSS base and not the PRM base.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
This patch adds OMAP4 specific PRM register defs. Auto generated
using a python script (gen_prm_4430_h.py) developed by Paul
Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch splits OMAP2_IO_ADDRESS to OMAP2_L3_IO_ADDRESS and
OMAP2_L4_IO_ADDRESS to reclaim more IO space.
The omap_read*() and omap_write*() functions will work only over
L4 address space. Current omap kernel stack uses these functions
only to access registers over L4 io address space
Note that these macros should only be used when ioremap does
not work. Please use ioremap instead in all new code.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Merge branch 'omap-rmk' into omap-all
|
|
OMAP1_IO_ADDRESS(), OMAP2_IO_ADDRESS() and IO_ADDRESS() returns cookies
for use with __raw_{read|write}* for accessing registers. Therefore,
these macros should return (void __iomem *) cookies, not integer values.
Doing this improves typechecking, and means we can find those places
where, eg, DMA controllers are incorrectly given virtual addresses to
DMA to, or physical addresses are thrown through a virtual to physical
address translation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add powerdomains common to both OMAP2 and OMAP3 (WKUP and GFX/SGX).
Modify mach-omap2/io.c to initialize the powerdomain code on boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise compiling in omap2 and omap3 will not work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
New struct omap_globals contains the omap processor specific
module bases. Use omap_globals to set the various base addresses
to make detecting omap chip type simpler.
Also introduce OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS for future multi-omap
patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Split sram24xx.S into sram242x.S and sram243x.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixed comments on global PRM register usage.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds common register access for 24xx and 34xx power
and clock management in order to share code between 24xx and 34xx.
Only change USB platform init code to use new register access, other
access will be changed in later patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
