| Age | Commit message (Collapse) | Author |
|---|
|
The GPIO pin connected to card detect was inverted twice: once by
the argument to the GPIO line itself where it was magically marked
as active low by the flag GPIO_ACTIVE_LOW (0x01) in the third cell,
and also marked active low AGAIN by explicitly stating
"cd-inverted" (a deprecated method).
After commit 78f87df2b4f8760954d7d80603d0cfcbd4759683
"mmc: mmci: Use the common mmc DT parser" this results in the
line being inverted twice so it was effectively uninverted, while
the old code would not have this effect, instead disregarding the
flag on the GPIO line altogether, which is a bug. I admit the
semantics may be unclear but inverting twice is as good a
definition as any on how this should work.
So fix up the buggy device tree. Use proper #includes so the DTS
is clear and readable.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap n900 regression fix for v3.16 rc series" from Tony Lindgren:
Minimal regression fix for n900 display that got broken with
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
* tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert enabling of twl configuration for n900
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 9188883fd66e9 (ARM: dts: Enable twl4030 off-idle configuration
for selected omaps) allowed n900 to cut off core voltages during
off-idle. This however caused a regression where twl regulator
vaux1 was not getting enabled for the LCD panel as we are not
requesting it for the panel.
Turns out quite a few devices on n900 are using vaux1, and we need
to either stop idling it, or add proper regulator_get calls for all
users. But until we have a proper solution implemented and tested,
let's just disable the twl off-idle configuration for now for n900.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 9188883fd66e9 (ARM: dts: Enable twl4030 off-idle configuration for selected omaps)
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix the address of L2 controler register in hi3620 SoC.
This has been wrong from the point that the file was merged
in v3.14.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Second Round of Renesas ARM Based SoC Fixes for v3.16" from Simon Horman
* Fix SD2CKCR register address of r8a7791 (R-Car M2) SoC
This corrects a bug introduced in v3.14 by
59e79895b9589286 ("ARM: shmobile: r8a7791: Add clocks").
However, it does not manifest in mainline code until
SDHI devices were enabled on the Koelsch board in v3.15 by
2c60a7df72711fb8 ("ARM: shmobile: Add SDHI devices for Koelsch DTS").
It also manifests on the Henninger board when
SDHI devices were enabled in v3.16-rc1 by
1299df03d7191ab4 ("ARM: shmobile: henninger: add SDHI0/2 DT support")
* tag 'renesas-fixes2-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: Fix SD2CKCR register address
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
59e79895b95892863617ce630fbda467f2470575
(ARM: shmobile: r8a7791: Add clocks)
added r8a7791 SD clocks when v3.14.
2c60a7df72711fb8b4be1e6aa651ab166a8931bc
(ARM: shmobile: Add SDHI devices for Koelsch DTS)
enabled SD on r8a7791 Koelsch when v3.15.
1299df03d7191ab4356c995dde8b912d3c8922e9
(ARM: shmobile: henninger: add SDHI0/2 DT support)
enable SD on r8a7791 Henninger when v3.16.
But r8a7791 SD clock had wrong address.
This patch fixup it.
[Kuninori Morimoto: tidyup for upstreaming]
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Merge "at91: fixes for 3.16 #2" from Nicolas Ferre:
Second AT91 fixes series for 3.16
- fix clock definitions after the move to CCF for:
* at91sam9n12 (ohci)
* at91sam9x5 (ohci, pwm)
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The pwm driver requires a clocks property referencing the pwm peripheral
clk.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
udphs_clk (USB Device Controller clock) is referenced instead of
uhphs_clk (USB Host Controller clock).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Correct the typo error for the second "uhphs_clk".
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes-3 for 3.16" from Kukjin Kim:
Samsung fixes-3 for v3.16
- update the parent for Auudss clock because kernel will be hang
during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
on/off, its regarding clock source will be reset and it causes
a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
system failure will be happened on other exynos SoCs.
* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: dts: Update the parent for Audss clocks in Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add clocks for usb device, or else switch to CCF, the gadget
won't work.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Adding the optional clock property for the mfc_pd for
handling the re-parenting while pd on/off.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.16-rc4" from Tony Lindgren:
Fixes for omaps for the -rc series. It's mostly fixes for clock rates,
restart handling and phy regulators and SATA interconnect data.
Also few build fixes related to the DSP driver in staging, and trivial
stuff like removal of broken and soon to be unused platform data init
for HDMI audio that would be good to get into the -rc series if not
too late.
* tag 'omap-for-v3.16/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
ARM: dts: am335x-evm: Enable the McASP FIFO for audio
ARM: OMAP2+: Make GPMC skip disabled devices
ARM: OMAP2+: create dsp device only on OMAP3 SoCs
ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
ARM: DRA7: hwmod: Fixup SATA hwmod
ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
ARM: dts: dra7xx-clocks: Fix the l3 and l4 clock rates
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes-2 for v3.16" from Kukjin Kim:
- fix the check for SMP configuration with using CONFIG_SMP
not just SMP
- fix the number of pwm-cells for exynos4 pwm
- fix ftrace for exynos_mct
- register exynos_mct for stable udely
- fix secondary boot addr for secure mode for exynos SoCs
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Update secondary boot addr for secure mode
clocksource: exynos_mct: Register the timer for stable udelay
clocksource: exynos_mct: Fix ftrace
ARM: dts: fix pwm-cells in pwm node for exynos4
ARM: EXYNOS: Fix the check for non-smp configuration
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Currently CLK_FOUT_EPLL was set as one of the parents of AUDSS mux.
As per the user manual, it should be CLK_MAU_EPLL.
The problem surfaced when the bootloader in Peach-pit board set
the EPLL clock as the parent of AUDSS mux. While booting the kernel,
we used to get a system hang during late boot if CLK_MAU_EPLL was
disabled.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
https://github.com/t-kristo/linux-pm into fixes-rc4
|
|
As this board use external clock for RMII interface we should specify 'rmii'
phy mode and 'rmii-clock-ext' to make ethernet working.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
After clarification from the hardware team it was found that
this 1.8V PHY supply can't be switched OFF when SoC is Active.
Since the PHY IPs don't contain isolation logic built in the design to
allow the power rail to be switched off, there is a very high risk
of IP reliability and additional leakage paths which can result in
additional power consumption.
The only scenario where this rail can be switched off is part of Power on
reset sequencing, but it needs to be kept always-on during operation.
This patch is required for proper functionality of USB, SATA
and PCIe on DRA7-evm.
CC: Rajendra Nayak <rnayak@ti.com>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge OMAP fixes from Tony Lindgren:
Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
|
|
pwm-cells should be 3. Third cell is optional PWM flags. And This flag
supported by this binding is PWM_POLARITY_INVERTED.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Without the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
532000000
With the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
266000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
133000000
The l3 clock derived from core DPLL is actually a divider clock,
with the default divider set to 2. l4 then derived from l3 is a fixed factor
clock, but the fixed divider is 2 and not 1. Which means the l3 clock is
half of core DPLLs h12x2 and l4 is half of l3 (as seen with this patch)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Merge "First AT91 fixes batch for 3.16" from Nicolas Ferre:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
|
|
Merge "mvebu fixes for v3.16" from Jason Cooper:
- mvebu
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- kirkwood
- Fix phy-connection-type on GuruPlug board
* tag 'mvebu-fixes-3.16' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
ARM: dts: kirkwood: fix phy-connection-type for Guruplug
ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
ARM: mvebu: Fix broken SoC ID detection
|
|
The at91sam9261 doesn't actually have a slow RC oscillator, remove it from the
dtsi.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Define at91sam9261ek's slow crystal frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
mainck (CKGR_MCFR register) is actually using main_osc (CKGR_MOR register).
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
wildcard
Wildcards in compatible strings should be avoid. "marvell,armada38x"
was recently introduced but was not yet used.
The armada 385 SoC is a superset of the armada 380 SoC (with more CPUs
and more PCIe slots). So this patch replaces the use of
"marvell,armada38x" by the "marvell,armada380" string.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1403533011-21339-1-git-send-email-gregory.clement@free-electrons.com
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Commit eeb845459a72e792a959278b858f9c417e9995bd
("ARM: dts: kirkwood: set Guruplug phy-connection-type to rgmii-id")
added phy-connection-type properties to ethernet PHY nodes.
Actually, the property has to be set for the ethernet port node instead.
Fix it by moving the corresponding properties to the correct nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1403555115-13111-1-git-send-email-sebastian.hesselbarth@gmail.com
Fixes: eeb845459a72: ('ARM: dts: kirkwood: set Guruplug phy-connection-type to rgmii-id')
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "i.MX fixes for 3.16" from Shawn Guo:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
* tag 'imx-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
ARM: dts: imx51-babbage: Fix esdhc setup
ARM: dts: mx5: Move the display out of soc {} node
ARM: dts: mx5: Fix IPU port node placement
ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
ARM: dts: hummingboard/cubox-i: move usb otg configuration to platform level
ARM: dts: cubox-i: add support for PWM-driven front panel LED
ARM: dts: imx6: ventana: correct gw52xx sgtl5000 clock source
ARM: dts: imx6qdl-gw5xxx: Fix Linear Technology vendor prefix
ARM: dts: imx6: ventana: fix include typo
ARM: dts: imx6sl: correct the fec ipg clock source
ARM: imx6sl: add missing enet clock for imx6sl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge Samsung fixes for 3.16 from Kukjin Kim:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
ARM: EXYNOS: fix pm code to check for cortex A9 rather than the SoC
clocksource: exynos_mct: Don't reset the counter during boot and resume
ARM: dts: fix reg sizes of GIC for exynos4
ARM: EXYNOS: Use wfi macro in platform_do_lowpower
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The following commit:
89d7e5c mmc: sdhci-esdhc-imx: add runtime pm support
has the effect of also disabling the hardware card detect
in runtime pm.
We switch to GPIO based detection to avoid this issue.
This patch is based on:
ARM: dts: imx51-babbage: Fix esdhc setup
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Since commit 89d7e5c13122 (mmc: sdhci-esdhc-imx: add runtime pm
support), controller based card detection / write protection is not
supported anymore by esdhc driver. Let's use GPIO for CD/WP on esdhc1
instead.
While at it, fix cd gpio polarity for esdhc2. This is wrong and
currently only works because the imx esdhc driver ignores the polarity.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Move the display {} node out of the soc {} node . This just aligns
the DT with other boards, there is no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The "port" node was misplaced in the original patch, therefore making
the LCD dysfunctional on this board. Fix this by moving the "port" DT
node into the "display {}" node.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
git://git.stlinux.com/devel/kernel/linux-sti into fixes
Merge "STi: DT fixes for v3.16" from Maxime Coquelin:
Couple of DT fixes for STi platform issues discovered on V3.16-rc1.
The fixes included are:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
* tag 'sti-fixes-for-v3.16-rc1' of git://git.stlinux.com/devel/kernel/linux-sti: (2963 commits)
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
ARM: STi: DT: Properly define sti-ethclk & stmmaceth for stih415/6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Two reasons for this rename. Firstly, it removes the camel case
convention which isn't used by any other platform and secondly it
matches the naming convention for the internal kernel, which can
become annoying when flipping between the two.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The factory bootloader on A385-DB boards expect the ECC strength to be
4 bits over 512 bytes. Hence, we need to specify this in the devicetree,
to prevent the kernel from assuming any different ECC scheme.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1400941030-2123-3-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The factory bootloader on A375-DB boards expect the ECC strength to be
4 bits over 512 bytes. Hence, we need to specify this in the devicetree,
to prevent the kernel from assuming any different ECC scheme.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1400941030-2123-2-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The OpenBlocks AX3-4 has a non-DT bootloader. It also comes with 1GB of
soldered on RAM, and a DIMM slot for expansion.
Unfortunately, atags_to_fdt() doesn't work in big-endian mode, so we see
the following failure when attempting to boot a big-endian kernel:
686 slab pages
17 pages shared
0 pages swap cached
[ pid ] uid tgid total_vm rss nr_ptes swapents oom_score_adj name
Kernel panic - not syncing: Out of memory and no killable processes...
CPU: 1 PID: 351 Comm: kworker/u4:0 Not tainted 3.15.0-rc8-next-20140603 #1
[<c0215a54>] (unwind_backtrace) from [<c021160c>] (show_stack+0x10/0x14)
[<c021160c>] (show_stack) from [<c0802500>] (dump_stack+0x78/0x94)
[<c0802500>] (dump_stack) from [<c0800068>] (panic+0x90/0x21c)
[<c0800068>] (panic) from [<c02b5704>] (out_of_memory+0x320/0x340)
[<c02b5704>] (out_of_memory) from [<c02b93a0>] (__alloc_pages_nodemask+0x874/0x930)
[<c02b93a0>] (__alloc_pages_nodemask) from [<c02d446c>] (handle_mm_fault+0x744/0x96c)
[<c02d446c>] (handle_mm_fault) from [<c02cf250>] (__get_user_pages+0xd0/0x4c0)
[<c02cf250>] (__get_user_pages) from [<c02f3598>] (get_arg_page+0x54/0xbc)
[<c02f3598>] (get_arg_page) from [<c02f3878>] (copy_strings+0x278/0x29c)
[<c02f3878>] (copy_strings) from [<c02f38bc>] (copy_strings_kernel+0x20/0x28)
[<c02f38bc>] (copy_strings_kernel) from [<c02f4f1c>] (do_execve+0x3a8/0x4c8)
[<c02f4f1c>] (do_execve) from [<c025ac10>] (____call_usermodehelper+0x15c/0x194)
[<c025ac10>] (____call_usermodehelper) from [<c020e9b8>] (ret_from_fork+0x14/0x3c)
CPU0: stopping
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.15.0-rc8-next-20140603 #1
[<c0215a54>] (unwind_backtrace) from [<c021160c>] (show_stack+0x10/0x14)
[<c021160c>] (show_stack) from [<c0802500>] (dump_stack+0x78/0x94)
[<c0802500>] (dump_stack) from [<c021429c>] (handle_IPI+0x138/0x174)
[<c021429c>] (handle_IPI) from [<c02087f0>] (armada_370_xp_handle_irq+0xb0/0xcc)
[<c02087f0>] (armada_370_xp_handle_irq) from [<c0212100>] (__irq_svc+0x40/0x50)
Exception stack(0xc0b6bf68 to 0xc0b6bfb0)
bf60: e9fad598 00000000 00f509a3 00000000 c0b6a000 c0b724c4
bf80: c0b72458 c0b6a000 00000000 00000000 c0b66da0 c0b6a000 00000000 c0b6bfb0
bfa0: c027bb94 c027bb24 60000313 ffffffff
[<c0212100>] (__irq_svc) from [<c027bb24>] (cpu_startup_entry+0x54/0x214)
[<c027bb24>] (cpu_startup_entry) from [<c0ac5b30>] (start_kernel+0x318/0x37c)
[<c0ac5b30>] (start_kernel) from [<00208078>] (0x208078)
---[ end Kernel panic - not syncing: Out of memory and no killable processes...
A similar failure will also occur if ARM_ATAG_DTB_COMPAT isn't selected.
Fix this by setting a sane default (1 GB) in the dts file.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: <stable@vger.kernel.org> #v3.13+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch fixes two problems: -
1) The device tree isn't currently providing sti-ethclk which is
required by the dwmac glue code to correctly configure the ethernet
PHY clock speed.
This means depending on what the bootloader/jtag has
configured this clock to, and what switch/hub the board is plugged
into you most likely will NOT successfully negotiate a ethernet link.
2) The stmmaceth clock was associated with the wrong clock. It was
referencing the PHY clock rather than the interconnect clock which
clocks the IP.
This patch also brings us closer to not having to boot the upstream
kernel with the clk_ignore_unused parameter.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The configuration of the USB OTG is a platform configuration decision,
not a microsom decision. Move this configuration out to the platform
level files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The front panel LED on the Cubox-i is driven by one of the iMX6 PWM
channels, and is wired between the PWM output and supply.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Correct the invalid clock for the sgtl5000 audio codec on the GW52xx Ventana
baseboard.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The vendor prefix for Linear Technology should be lltc,
same as the NASDAQ symbol.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Fix typo and include the right dtsi file for the gw51xx board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
