| Age | Commit message (Collapse) | Author |
|---|
|
commit f6365201d8a21fb347260f89d6e9b3e718d63c70 upstream.
The X86_32-only disable_hlt/enable_hlt mechanism was used by the
32-bit floppy driver. Its effect was to replace the use of the
HLT instruction inside default_idle() with cpu_relax() - essentially
it turned off the use of HLT.
This workaround was commented in the code as:
"disable hlt during certain critical i/o operations"
"This halt magic was a workaround for ancient floppy DMA
wreckage. It should be safe to remove."
H. Peter Anvin additionally adds:
"To the best of my knowledge, no-hlt only existed because of
flaky power distributions on 386/486 systems which were sold to
run DOS. Since DOS did no power management of any kind,
including HLT, the power draw was fairly uniform; when exposed
to the much hhigher noise levels you got when Linux used HLT
caused some of these systems to fail.
They were by far in the minority even back then."
Alan Cox further says:
"Also for the Cyrix 5510 which tended to go castors up if a HLT
occurred during a DMA cycle and on a few other boxes HLT during
DMA tended to go astray.
Do we care ? I doubt it. The 5510 was pretty obscure, the 5520
fixed it, the 5530 is probably the oldest still in any kind of
use."
So, let's finally drop this.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Stephen Hemminger <shemminger@vyatta.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-3rhk9bzf0x9rljkv488tloib@git.kernel.org
[ If anyone cares then alternative instruction patching could be
used to replace HLT with a one-byte NOP instruction. Much simpler. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49d859d78c5aeb998b6936fcb5f288f78d713489 upstream.
If the CPU declares that RDRAND is available, go through a guranteed
reseed sequence, and make sure that it is actually working (producing
data.) If it does not, disable the CPU feature flag.
Allow RDRAND to be disabled on the command line (as opposed to at
compile time) for a user who has special requirements with regards to
random numbers.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2584f5212d97b664be250ad5700a2d0fee31a10d upstream.
Also add information on where the respective trees are.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4356f21d09283dc6d39a6f7287a65ddab61e2808 upstream.
Stable note: Not tracked in Bugzilla. This patch makes later patches
easier to apply but has no other impact.
Change ISOLATE_XXX macro with bitwise isolate_mode_t type. Normally,
macro isn't recommended as it's type-unsafe and making debugging harder as
symbol cannot be passed throught to the debugger.
Quote from Johannes
" Hmm, it would probably be cleaner to fully convert the isolation mode
into independent flags. INACTIVE, ACTIVE, BOTH is currently a
tri-state among flags, which is a bit ugly."
This patch moves isolate mode from swap.h to mmzone.h by memcontrol.h
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb3979f64d25120d60b9e761a4c58f70b1a02f86 upstream.
Distribution kernel maintainers routinely backport fixes for users that
were deemed important but not "something critical" as defined by the
rules. To users of these kernels they are very serious and failing to fix
them reduces the value of -stable.
The problem is that the patches fixing these issues are often subtle and
prone to regressions in other ways and need greater care and attention.
To combat this, these "serious" backports should have a higher barrier
to entry.
This patch relaxes the rules to allow a distribution maintainer to merge
to -stable a backported patch or small series that fixes a "serious"
user-visible performance issue. They should include additional information on
the user-visible bug affected and a link to the bugzilla entry if available.
The same rules about the patch being already in mainline still apply.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 591bfc6bf9e5e25e464fd4c87d64afd5135667c4 upstream.
The HOWTO document needed updating for the new kernel versioning. The
git URI for -next was updated as well.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b49960a05e32121d29316cfdf653894b88ac9190 ]
tcp_adv_win_scale default value is 2, meaning we expect a good citizen
skb to have skb->len / skb->truesize ratio of 75% (3/4)
In 2.6 kernels we (mis)accounted for typical MSS=1460 frame :
1536 + 64 + 256 = 1856 'estimated truesize', and 1856 * 3/4 = 1392.
So these skbs were considered as not bloated.
With recent truesize fixes, a typical MSS=1460 frame truesize is now the
more precise :
2048 + 256 = 2304. But 2304 * 3/4 = 1728.
So these skb are not good citizen anymore, because 1460 < 1728
(GRO can escape this problem because it build skbs with a too low
truesize.)
This also means tcp advertises a too optimistic window for a given
allocated rcvspace : When receiving frames, sk_rmem_alloc can hit
sk_rcvbuf limit and we call tcp_prune_queue()/tcp_collapse() too often,
especially when application is slow to drain its receive queue or in
case of losses (netperf is fast, scp is slow). This is a major latency
source.
We should adjust the len/truesize ratio to 50% instead of 75%
This patch :
1) changes tcp_adv_win_scale default to 1 instead of 2
2) increase tcp_rmem[2] limit from 4MB to 6MB to take into account
better truesize tracking and to allow autotuning tcp receive window to
reach same value than before. Note that same amount of kernel memory is
consumed compared to 2.6 kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1bd612a25855f4cc9345052b53d7da697dba6358 upstream.
Also update IDT datasheet locations.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4de86126a712ba83fa038d277c8282f7ed466a4b upstream.
These are fully compatible with Jedec JC 42.4 as far as I can see.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8cae98cddd286e38db1724dda1b0e7b467f9237 upstream.
The documentation for usbmon is out of date; the usbfs "devices" file
now exists in /sys/kernel/debug/usb rather than /proc/bus/usb. This
patch (as1505) updates the documentation accordingly, and also
mentions that the necessary information can be found by running lsusb.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2eb7f204db51969ea558802a6601d79c2fb273b9 upstream.
The Japanese/Korean/Chinese versions still need updating.
Also, the stable kernel 2.6.x.y descriptions are out of date
and should be updated as well.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 886486b792e4f6f96d4fbe8ec5bf20811cab7d6a upstream.
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c1650b8b4aceb3856bebbde6daa3b86 (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. Therefore
this patch (as1492) adds a mechanism for retrying failed
autosuspends. If the callback routine updates the last_busy field so
that the next autosuspend expiration time is in the future, the
autosuspend will automatically be rescheduled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 93b465c2e186d96fb90012ba0f9372eb9952e732 upstream.
Since we're using non-atomic radix tree allocations, we
should be protecting the tree using a mutex and not a
spinlock.
Non-atomic allocations and process context locking is good enough,
as the tree is manipulated only when locks are registered/
unregistered/requested/freed.
The locks themselves are still protected by spinlocks of course,
and mutexes are not involved in the locking/unlocking paths.
Signed-off-by: Juan Gutierrez <jgutierrez@ti.com>
[ohad@wizery.com: rewrite the commit log, #include mutex.h, add minor
commentary]
[ohad@wizery.com: update register/unregister parts in hwspinlock.txt]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5fa224295f0e0358c8bc0e5390702338df889def upstream.
The stable@kernel.org email address has been replaced with the
stable@vger.kernel.org mailing list. Change the stable kernel rules to
reference the new list instead of the semi-defunct email alias.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e22a539824e8ddb82c87b4f415165ede82e6ab56 upstream.
The CONFIG_RELOCATABLE code tries to align the unpack destination to
the value of 'kernel_alignment' in the setup_hdr. If that's 0, it
tries to unpack to address 0, which in fact causes the gunzip code
to call 'error("Out of memory while allocating output buffer")'.
The bootloader (ie. the lguest Launcher in this case) should be doing
setting this field; the normal bzImage is 16M, we can use the same.
Reported-by: Stefanos Geraggelos <sgerag@cslab.ece.ntua.gr>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86. reboot: Make Dell Latitude E6320 use reboot=pci
x86, doc only: Correct real-mode kernel header offset for init_size
x86: Disable AMD_NUMA for 32bit for now
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: remove resize from unsupported features list
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
|
|
Resize feature was supported by the commit 4e33f9eab07e but it was not
reflected to the list of unsupported features in nilfs2.txt file.
This updates the list to fix discrepancy.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
|
|
The real-mode kernel header init_size field is located at 0x260 per the field
listing in th e"REAL-MODE KERNEL HEADER" section. It is listed as 0x25c in
the "DETAILS OF HEADER FIELDS" section, which overlaps with pref_address.
Correct the details listing to 0x260.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Link: http://lkml.kernel.org/r/541cf88e2dfe5b8186d8b96b136d892e769a68c1.1310441260.git.dvhart@linux.intel.com
CC: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
That file harkens back to the days of the big 2.4 -> 2.6 version jump,
and was based even then on older versions. Some of it is just obsolete,
and Jesper Juhl points out that it talks about kernel versions 2.6 and
should be updated to 3.0.
Remove some obsolete text, and re-phrase some other to not be 2.6-specific.
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
hp-wmi: fix use after free
dell-laptop - using buffer without mutex_lock
Revert: "dell-laptop: Toggle the unsupported hardware killswitch"
platform-drivers-x86: set backlight type to BACKLIGHT_PLATFORM
thinkpad-acpi: handle HKEY 0x4010, 0x4011 events
drivers/platform/x86: Fix memory leak
thinkpad-acpi: handle some new HKEY 0x60xx events
acer-wmi: fix bitwise bug when set device state
acer-wmi: Only update rfkill status for associated hotkey events
|
|
Since we removed sti()/cli() and related, how about removing it from
Documentation/spinlocks.txt?
Signed-off-by: Muthukumar R <muthur@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: conditional resource-reallocation through kernel parameter pci=realloc
|
|
Multiple attempts to dynamically reallocate pci resources have
unfortunately lead to regressions. Though we continue to fix the
regressions and fine tune the dynamic-reallocation behavior, we have not
reached a acceptable state yet.
This patch provides a interim solution. It disables dynamic reallocation
by default, but adds the ability to enable it through pci=realloc kernel
command line parameter.
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Default should be listed at 8 instead of 7.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an FS-Cache helper to bulk uncache pages on an inode. This will
only work for the circumstance where the pages in the cache correspond
1:1 with the pages attached to an inode's page cache.
This is required for CIFS and NFS: When disabling inode cookie, we were
returning the cookie and setting cifsi->fscache to NULL but failed to
invalidate any previously mapped pages. This resulted in "Bad page
state" errors and manifested in other kind of errors when running
fsstress. Fix it by uncaching mapped pages when we disable the inode
cookie.
This patch should fix the following oops and "Bad page state" errors
seen during fsstress testing.
------------[ cut here ]------------
kernel BUG at fs/cachefiles/namei.c:201!
invalid opcode: 0000 [#1] SMP
Pid: 5, comm: kworker/u:0 Not tainted 2.6.38.7-30.fc15.x86_64 #1 Bochs Bochs
RIP: 0010: cachefiles_walk_to_object+0x436/0x745 [cachefiles]
RSP: 0018:ffff88002ce6dd00 EFLAGS: 00010282
RAX: ffff88002ef165f0 RBX: ffff88001811f500 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000100 RDI: 0000000000000282
RBP: ffff88002ce6dda0 R08: 0000000000000100 R09: ffffffff81b3a300
R10: 0000ffff00066c0a R11: 0000000000000003 R12: ffff88002ae54840
R13: ffff88002ae54840 R14: ffff880029c29c00 R15: ffff88001811f4b0
FS: 00007f394dd32720(0000) GS:ffff88002ef00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007fffcb62ddf8 CR3: 000000001825f000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process kworker/u:0 (pid: 5, threadinfo ffff88002ce6c000, task ffff88002ce55cc0)
Stack:
0000000000000246 ffff88002ce55cc0 ffff88002ce6dd58 ffff88001815dc00
ffff8800185246c0 ffff88001811f618 ffff880029c29d18 ffff88001811f380
ffff88002ce6dd50 ffffffff814757e4 ffff88002ce6dda0 ffffffff8106ac56
Call Trace:
cachefiles_lookup_object+0x78/0xd4 [cachefiles]
fscache_lookup_object+0x131/0x16d [fscache]
fscache_object_work_func+0x1bc/0x669 [fscache]
process_one_work+0x186/0x298
worker_thread+0xda/0x15d
kthread+0x84/0x8c
kernel_thread_helper+0x4/0x10
RIP cachefiles_walk_to_object+0x436/0x745 [cachefiles]
---[ end trace 1d481c9af1804caa ]---
I tested the uncaching by the following means:
(1) Create a big file on my NFS server (104857600 bytes).
(2) Read the file into the cache with md5sum on the NFS client. Look in
/proc/fs/fscache/stats:
Pages : mrk=25601 unc=0
(3) Open the file for read/write ("bash 5<>/warthog/bigfile"). Look in proc
again:
Pages : mrk=25601 unc=25601
Reported-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-and-Tested-by: Suresh Jayaraman <sjayaraman@suse.de>
cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Radio devices have weird side-effects when used with combined TV/radio
tuners and the V4L2 spec is ambiguous on how it should work. This results
in inconsistent driver behavior which makes life hard for everyone.
Be more strict in when and how the switch between radio and tv mode
takes place and make sure all drivers behave the same.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Handle events 0x4010 and 0x4011 so that we do not pester users about them.
These events report when the thinkpad is docked/undocked to a native
hotplug dock (i.e. one that does not need ACPI handling, nor is represented
in the ACPI device tree). Such docks are based on USB 2.0/3.0, and also
work as port replicators.
We really want a proper dock class to report these, or at least new input
EV_SW events. Since it is not clear which one to use yet, keep reporting
them as vendor-specific ThinkPad events.
WARNING: As defined by the thinkpad-acpi sysfs ABI rules of engagement, the
vendor-specific events will be REMOVED as soon as generic events are made
available (duplicate events are a big problem), with an appropriate update
to the thinkpad-acpi sysfs/event ABI versioning. Userspace is already
prepared to provide easy backwards compatibility for such changes when
convenient to the distro (see acpi-fakekey).
* Event 0x4010: docking to hotplug dock/port replicator
* Event 0x4011: undocking from hotplug dock/port replicator
Typical usecase would be to trigger display reconfiguration.
Reports mention T410, T510, and series 3 docks/port replicators. Special
thanks to Robert de Rooy for his extensive report and analysis of the
situation.
http://www.thinkwiki.org/wiki/ThinkPad_Port_Replicator_Series_3
http://www.thinkwiki.org/wiki/ThinkPad_Mini_Dock_Series_3
http://www.thinkwiki.org/wiki/ThinkPad_Mini_Dock_Plus_Series_3
http://www.thinkwiki.org/wiki/ThinkPad_Mini_Dock_Plus_Series_3_for_Mobile_Workstations
http://lenovoblogs.com/insidethebox/?p=290
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Reported-by: Claudius Hubig <claudiushubig@chubig.net>
Reported-by: Doctor Bill <docbill@gmail.com>
Reported-by: Korte Noack <gbk.noack@gmx.de>
Reported-by: Robert de Rooy <robert.de.rooy@gmail.com>
Reported-by: Sebastian Will <swill@csail.mit.edu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Handle some user interface events from the newer Lenovo models. We are likely
to do something smart with these events in the future, for now, hide the ones
we are already certain about from the user and userspace both.
* Events 0x6000 and 0x6005 are key-related. 0x6005 is not properly identified
yet. Ignore these events, and do not report them.
* Event 0x6040 has not been properly identified yet, and we don't know if it
is important (looks like it isn't, but still...). Keep reporting it.
* Change the message the driver outputs on unknown 0x6xxx events, as all
recent events are not related to thermal alarms. Degrade log level from
ALERT to WARNING.
Thanks to all users who reported these events or asked about them in a number
of mailing lists. Your help is highly appreciated, even if I did took a lot of
time to act on them. For that I apologise.
I will list those that identified the reasons for the events as "reported-by",
and I apologise in advance if I leave anyone out: it was not done on purpose, I
made the mistake of not properly tagging all event report emails separately,
and might have missed some.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Markus Malkusch <markus@malkusch.de>
Reported-by: Peter Giles <g1l3sp@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
All the blkio.throttle.* file names are incorrectly reported without
".throttle" in the documentation. Fix it.
Signed-off-by: Andrea Righi <andrea@betterlinux.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The list of available general purpose memory allocators in
Documentation/CodingStyle chapter 14 is incomplete. This patch adds
the missing vzalloc() to the list.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Update documentation regarding driver removal
PM: Documentation: fix typo: pm_runtime_idle_sync() doesn't exist.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k10temp) Update documentation for Fam12h
hwmon-vid: Fix typo in VIA CPU name
hwmon: (f71882fg) Add support for the F71869A
hwmon: Use <> rather than () around my e-mail address
hwmon: (emc6w201) Properly handle all errors
|
|
Add some CPU series IDs and links to the Fam12h datasheets.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Baldwin <archerseven@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Commit e1866b33b1e89f077b7132daae3dfd9a594e9a1a (PM / Runtime: Rework
runtime PM handling during driver removal) forgot to update the
documentation in Documentation/power/runtime_pm.txt to match the new
code in drivers/base/dd.c. Update that documentation to match the
code it describes.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
|
|
Replace reference to pm_runtime_idle_sync() in the driver core with
pm_runtime_put_sync() which is used in the code.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
MAINTAINERS: add myself as maintainer of USB/IP
usb: r8a66597-hcd: fix cannot detect low/full speed device
USB: ehci-ath79: fix a NULL pointer dereference
USB: Add new FT232H chip to drivers/usb/serial/ftdi_sio.c
usb/isp1760: Fix bug preventing the unlinking of control urbs
USB: Fix up URB error codes to reflect implementation.
xhci: Always set urb->status to zero for isoc endpoints.
xhci: Add reset on resume quirk for asrock p67 host
xHCI 1.0: Incompatible Device Error
USB: don't let errors prevent system sleep
USB: don't let the hub driver prevent system sleep
USB: change maintainership of ohci-hcd and ehci-hcd
xHCI 1.0: Force Stopped Event(FSE)
xhci: Don't warn about zeroed bMaxBurst descriptor field.
USB: Free bandwidth when usb_disable_device is called.
xhci: Reject double add of active endpoints.
USB: TI 3410/5052 USB Serial Driver: Fix mem leak when firmware is too big.
usb: musb: gadget: clear TXPKTRDY flag when set FLUSHFIFO
usb: musb: host: compare status for negative error values
|
|
Commit 4d27e9dcff00a6425d779b065ec8892e4f391661 (PM: Make power
domain callbacks take precedence over subsystem ones) forgot to
update the device power management documentation to take changes
made by it into account. Correct that mistake.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The part of Documentation/power/devices.txt regarding sysdevs is not
valid any more after commit 2e711c04dbbf7a7732a3f7073b1fc285d12b369d
(PM: Remove sysdev suspend, resume and shutdown operations), so
remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Commit e8665002477f0278f84f898145b1f141ba26ee26 (PM: Allow
pm_runtime_suspend() to succeed during system suspend) removed usage
count increment across system PM.
Update doc to reflect this.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: Move RCU_BOOST #ifdefs to header file
rcu: use softirq instead of kthreads except when RCU_BOOST=y
rcu: Use softirq to address performance regression
rcu: Simplify curing of load woes
|
|
Documentation/usb/error-codes.txt mentions that urb->status can be set to
-EXDEV, if the isochronous transfer was not fully completed. However, in
practice, EHCI, UHCI, and OHCI all only set -EXDEV in the individual frame
status, never in the URB status. Those host controller actually always
pass in a zero status to usb_hcd_giveback_urb, and rely on the core to set
the appropriate status value.
The xHCI driver ran into issues with the uvcvideo driver when it tried to
set -EXDEV in urb->status, because the driver refused to submit URBs, and
the userspace camera application's video froze.
Clean up the documentation to reflect the actual implementation.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
|
Fix format and spelling.
Signed-off-by: Jörg Sommer <joerg@alea.gnuu.de>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
According to commit 676db4af0430 ("cgroupfs: create /sys/fs/cgroup to
mount cgroupfs on") the canonical mountpoint for the cgroup filesystem
is /sys/fs/cgroup. Hence, this should be used in the documentation.
Signed-off-by: Jörg Sommer <joerg@alea.gnuu.de>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Instead of listing the architectures that are supported by
kmemleak in Documentation/kmemleak.txt, just refer people to
the list of supported architecutures in lib/Kconfig.debug so
that Documentation/kmemleak.txt does not need more updates
for this.
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch updates the incomplete documentation concerning the printk
extended format specifiers.
Signed-off-by: Andrew Murray <amurray@mpc-data.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
feature-removal-schedule.txt
Commit a77aea92010acf ("cgroup: remove the ns_cgroup") removed the
ns_cgroup but it forgot to remove the related doc in
feature-removal-schedule.txt.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
