| Age | Commit message (Collapse) | Author |
|---|
|
Add PWM manual control.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
|
|
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
|
|
The lm87 driver normally assumes that firmware configured the chip
correctly. Since this is not always the case, alllow platform code to
set the channel register value via platform_data. All other
configuration registers can be changed after driver initialisation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC. Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
|
|
* 'docs' of git://git.lwn.net/linux-2.6:
Document panic_on_unrecovered_nmi sysctl
Add a reference to paper to SubmittingPatches
Add kerneldoc documentation for new printk format extensions
Remove videobook.tmpl
doc: Test-by?
Add the development process document
Documentation/block/data-integrity.txt: Fix section numbers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits)
Input: wm97xx - update email address for Liam Girdwood
Input: i8042 - add Thinkpad R31 to nomux list
Input: move map_to_7segment.h to include/linux
Input: ads7846 - fix cache line sharing issue
Input: cm109 - add missing newlines to messages
Input: document i8042.debug in kernel-parameters.txt
Input: keyboard - fix potential out of bound access to key_map
Input: psmouse - add OLPC touchpad driver
Input: psmouse - tweak PSMOUSE_DEFINE_ATTR to support raw set callbacks
Input: psmouse - add psmouse_queue_work() for ps/2 extension to make use of
Input: psmouse - export psmouse_set_state for ps/2 extensions to use
Input: ads7846 - introduce .gpio_pendown to get pendown state
Input: ALPS - add signature for DualPoint found in Dell Latitude E6500
Input: serio_raw - allow attaching to translated (SERIO_I8042XL) ports
Input: cm109 - don't use obsolete logging macros
Input: atkbd - expand Latitude's force release quirk to other Dells
Input: bf54x-keys - add power management support
Input: atmel_tsadcc - improve accuracy
Input: convert drivers to use strict_strtoul()
Input: appletouch - handle geyser 3/4 status bits
...
|
|
This adds "panic_on_unrecovered_nmi" sysctl to
Documentation/filesystems/proc.txt. The text is mainly taken from
http://readlist.com/lists/vger.kernel.org/linux-kernel/43/217998.html.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
decnet: Fix compiler warning in dn_dev.c
IPV6: Fix default gateway criteria wrt. HIGH/LOW preference radv option
net/802/fc.c: Fix compilation warnings
netns: correct mib stats in ip6_route_me_harder()
netns: fix net_generic array leak
rt2x00: fix regression introduced by "mac80211: free up 2 bytes in skb->cb"
rtl8187: Add USB ID for Belkin F5D7050 with RTL8187B chip
p54usb: Device ID updates
mac80211: fixme for kernel-doc
ath9k/mac80211: disallow fragmentation in ath9k, report to userspace
libertas : Remove unused variable warning for "old_channel" from cmd.c
mac80211: Fix scan RX processing oops
orinoco: fix unsafe locking in spectrum_cs_suspend
orinoco: fix unsafe locking in orinoco_cs_resume
cfg80211: fix debugfs error handling
mac80211: fix debugfs netdev rename
iwlwifi: fix ct kill configuration for 5350
mac80211: fix HT information element parsing
p54: Fix compilation problem on PPC
mac80211: fix debugfs lockup
...
|
|
Provide some additional details about the status of the driver and the
ds2490 hardware.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Document w1_master_add, w1_master_remove, search_count, and pullup.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Added strong pullup to thermal sensor driver and general documentation on
the sensor.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update Erik Mouw's email address & affiliation in DocBook.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Erik Mouw <mouw@nl.linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Document the change from the old "mode" parameter to the "mode_option"
parameter.
Signed-off-by: Mike Pagano <mpagano@gentoo.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for Intel's 945GME graphics chip to the intelfb driver. I
have assumed that the 945GME is identical to the already-supported 945GM
apart from its PCI IDs; this is based on a quick look at the X driver for
these chips which seems to treat them identically.
The 945GME is used in the ASUS Eee 901, and I coded this in the hope that
I'd be able to use it to get a console at the native 1024x600 resolution
which is not known to the BIOS. I realised too late that the intelfb
driver does not support mode changing on laptops, so it won't be any
use for me.
Signed-off-by: Phil Endecott <spam_from_intelfb@chezphil.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Correct via_fb_ to viafb_ and remove the Kconfig part in viafb.txt.
viafb.modes: supported mode table
viafb.txt: documentation of viafb driver
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new internal mechanism to gpiolib to support low power
operations by letting gpio_chip instances see when their GPIOs
are in use. When no GPIOs are active, chips may be able to
enter lower powered runtime states by disabling clocks and/or
power domains.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Magnus Damm" <magnus.damm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new gpiolib mechanism: gpio_chip instances can provide mappings
between their (input) GPIOs and any associated IRQs. This makes it easier
for platforms to support IRQs that are provided by board-specific external
chips instead of as part of their core (such as SOC-integrated GPIOs).
Also update the irq_to_gpio() description, saying to avoid it because it's
not always supported.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add documentation for the miscellaneous device module of autofs4.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make the chip info structure data optional by providing reasonable
defaults. Improve corresponding documentation, and highlight the drawback
of not providing explicit chipselect control.
DMA can determine appropriate dma_burst_size and thresholds automatically
so use DMA even if dma_burst_size is not specified.
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Reviewed-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For this year's OLS I wrote a paper on successfull strategies to submit
difficult kernel patches. Add a reference to it to SubmittingPatches.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds "panic_on_unrecovered_nmi" sysctl to
Documentation/filesystems/proc.txt. The text is mainly taken from
http://readlist.com/lists/vger.kernel.org/linux-kernel/43/217998.html.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove Andrew Morton's http://www.zip.com.au/~akpm/ urls, update to new
ones when necessary, delete references otherwise.
There are still instances of that living in:
Documentation/zh_CN/HOWTO
Documentation/zh_CN/SubmittingPatches
Documentation/ko_KR/HOWTO
Documentation/ja_JP/SubmittingPatches
Signed-off-by: Francois Cami <francois.cami@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
People can use the real name an an index into MAINTAINERS to find the
current email address.
Signed-off-by: Francois Cami <francois.cami@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We want all uses of memory barriers to be explained in the source code.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
defkeymap.c_shipped should be diffed if it is changed.
Reported-by: Mike Galbraith <efault@gmx.de>
COPYING, CREDITS, .mailmap should be diffed if they are changed.
keywords.c_shipped & lex.c_shipped should be diffed when changed.
parse.[ch]_shipped should be diffed when changed.
Reported-by: Sam Ravnborg <sam@ravnborg.org>
vsyscall* updates from a .gitignore patch by "Denis V. Lunev" <den@openvz.org>.
*.so.dbg from a .gitignore patch by Thomas Gleixner <tglx@linutronix.de>.
binoffset from a .gitignore patch by Uwe Kleine-Koenig
<Uwe.Kleine-Koenig@digi.com>.
Module.markers from a .gitignore patch by Matthew Wilcox
<willy@linux.intel.com>.
vmlinux*.lds* should be diffed if changed.
Reported-by: Etienne Lorrain <etienne_lorrain@yahoo.fr>
vmlinux.lds from a .gitignore patch by Daniel Guilak
<daniel@danielguilak.com>.
*.scr should be diffed if changed.
Lots of updates from http://lkml.org/lkml/2008/5/20/32 Reported-by: Bart
Van Assche <bart.vanassche@gmail.com>
Use ncscope.* instead of *cscope* since the latter may catch too many files.
Add *.elf, from a .gitignore patch by Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>.
Make firmware entries match .gitignore entries.
Make some entries less greedy by removing trailing '*'.
Remove "make_times_h" (no such file).
Remove "filelist" (no such file).
Remove "dummy_sym.c" (no such file).
Remove "gen-kdb_cmds.c" (no such file).
Remove "gentbl" (no such file).
Remove "kconfig.tk" (no such file).
Remove "tkparse" (no such file).
Remove "sim710_d.h" (no such file).
Remove "53c8xx_d.h" (no such file).
Add "syscalltab.h" (generated file).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a missing word to the explanation of the purpose of the zdisk and
bzdisk make targets.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Way too often, I have a machine that exhibits some kind of crappy
behavior. The CPU looks wedged in the kernel or it is spending way too
much system time and I wonder what is responsible.
I try to run readprofile. But, of course, Ubuntu doesn't enable it by
default. Dang!
The reason we boot-time enable it is that it takes a big bufffer that we
generally can only bootmem alloc. But, does it hurt to at least try and
runtime-alloc it?
To use:
echo 2 > /sys/kernel/profile
Then run readprofile like normal.
This should fix the compile issue with allmodconfig. I've compile-tested
on a bunch more configs now including a few more architectures.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the '%pF' format to get rid of an "#ifdef DEBUG" and make some printks
atomic.
This removes the last in-tree uses of print_fn_descriptor_symbol(). I
marked print_fn_descriptor_symbol() deprecated and scheduled it for
removal next year to give time for out-of-tree modules to be updated.
parisc's print_fn_descriptor_symbol() is currently broken there (it needs
to dereference the function pointer similar to ia64 and power). This
patch shouldn't make anything worse, but it means we need to fix
dereference_function_descriptor() instead of print_fn_descriptor_symbol()
to get meaningful initcall_debug output.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Danny ter Haar <dth@cistron.nl>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
First a file hello.c is created, then the file hello2.c is compiled.
Change this to hello.c
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As pm_trace uses the system's hardware clock to save its magic value,
users of that option should be warned that using this debug option will
result in an incorrect system time after resume.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a reference to paper to SubmittingPatches
For this year's OLS I wrote a paper on successfull strategies
to submit difficult kernel patches. Add a reference to it to
SubmittingPatches.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This document describes the long-deprecated V4L1 interface. In-tree, it
can only serve to encourage developers to write drivers to the wrong API.
Remove it in favor of the V4L2 documentation which must surely show up
someday.
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Commonly used is "Tested-by."
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This is an extended document intended to help interested developers, their
managers, and their employers work with the kernel development process.
This work was supported by the Linux Foundation.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Signed-off-by: Alberto Bertogli <albertito@blitiri.com.ar>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
When looking at kobject_rename I found two bugs with
that exist when sysfs support is disabled in the kernel.
kobject_rename does not change the name on the kobject when
sysfs support is not compiled in.
kobject_rename without locking attempts to check the
validity of a rename operation, which the kobject layer
simply does not have the infrastructure to do.
This patch documents the previously unstated requirement of
kobject_rename that is the responsibility of the caller to
provide mutual exclusion and to be certain that the new_name
for the kobject is valid.
This patch modifies sysfs_rename_dir in !CONFIG_SYSFS case
to call kobject_set_name to actually change the kobject_name.
This patch removes the bogus and misleading check in kobject_rename
that attempts to see if a rename is valid. The check is bogus
because we do not have the proper locking. The check is misleading
because it looks like we can and do perform checking at the kobject
level that we don't.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Base infrastructure to enable per-module debug messages.
I've introduced CONFIG_DYNAMIC_PRINTK_DEBUG, which when enabled centralizes
control of debugging statements on a per-module basis in one /proc file,
currently, <debugfs>/dynamic_printk/modules. When, CONFIG_DYNAMIC_PRINTK_DEBUG,
is not set, debugging statements can still be enabled as before, often by
defining 'DEBUG' for the proper compilation unit. Thus, this patch set has no
affect when CONFIG_DYNAMIC_PRINTK_DEBUG is not set.
The infrastructure currently ties into all pr_debug() and dev_dbg() calls. That
is, if CONFIG_DYNAMIC_PRINTK_DEBUG is set, all pr_debug() and dev_dbg() calls
can be dynamically enabled/disabled on a per-module basis.
Future plans include extending this functionality to subsystems, that define
their own debug levels and flags.
Usage:
Dynamic debugging is controlled by the debugfs file,
<debugfs>/dynamic_printk/modules. This file contains a list of the modules that
can be enabled. The format of the file is as follows:
<module_name> <enabled=0/1>
.
.
.
<module_name> : Name of the module in which the debug call resides
<enabled=0/1> : whether the messages are enabled or not
For example:
snd_hda_intel enabled=0
fixup enabled=1
driver enabled=0
Enable a module:
$echo "set enabled=1 <module_name>" > dynamic_printk/modules
Disable a module:
$echo "set enabled=0 <module_name>" > dynamic_printk/modules
Enable all modules:
$echo "set enabled=1 all" > dynamic_printk/modules
Disable all modules:
$echo "set enabled=0 all" > dynamic_printk/modules
Finally, passing "dynamic_printk" at the command line enables
debugging for all modules. This mode can be turned off via the above
disable command.
[gkh: minor cleanups and tweaks to make the build work quietly]
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
|
|
Manual fixup of conflicts on:
arch/powerpc/include/asm/dcr-regs.h
drivers/net/ibm_newemac/core.h
|
|
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-viapro: Add support for SMBus Process Call transactions
i2c: Restore i2c_smbus_process_call function
i2c: Do earlier driver model init
i2c: Only build Tyan SMBus mux drivers on x86
i2c: Guard against oopses from bad init sequences
i2c: Document the implementation details of the /dev interface
i2c: Improve dev-interface documentation
i2c-parport-light: Don't register a platform device resource
hwmon: (dme1737) Convert to a new-style i2c driver
hwmon: (dme1737) Be less i2c-centric
i2c/tps65010: Vibrator hookup to gpiolib
i2c-viapro: Add VX800/VX820 support
i2c: Renesas Highlander FPGA SMBus support
i2c-pca-isa: Don't grab arbitrary resources
i2c/isp1301_omap: Convert to a new-style i2c driver, part 2
i2c/isp1301_omap: Convert to a new-style i2c driver, part 1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (55 commits)
HID: build drivers for all quirky devices by default
HID: add missing blacklist entry for Apple ATV ircontrol
HID: add support for Bright ABNT2 brazilian device
HID: Don't let Avermedia Radio FM800 be handled by usb hid drivers
HID: fix numlock led on Dell device 0x413c/0x2105
HID: remove warn() macro from usb hid drivers
HID: remove info() macro from usb HID drivers
HID: add appletv IR receiver quirk
HID: fix a lockup regression when using force feedback on a PID device
HID: hiddev.h: Fix example code.
HID: hiddev.h: Fix mixed space and tabs in example code.
HID: convert to dev_* prints
HID: remove hid-ff
HID: move zeroplus FF processing
HID: move thrustmaster FF processing
HID: move pantherlord FF processing
HID: fix incorrent length condition in hidraw_write()
HID: fix tty<->hid deadlock
HID: ignore iBuddy devices
HID: report descriptor fix for remaining MacBook JIS keyboards
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (56 commits)
ocfs2: Make cached block reads the common case.
ocfs2: Kill the last naked wait_on_buffer() for cached reads.
ocfs2: Move ocfs2_bread() into dir.c
ocfs2: Simplify ocfs2_read_block()
ocfs2: Require an inode for ocfs2_read_block(s)().
ocfs2: Separate out sync reads from ocfs2_read_blocks()
ocfs2: Refactor xattr list and remove ocfs2_xattr_handler().
ocfs2: Calculate EA hash only by its suffix.
ocfs2: Move trusted and user attribute support into xattr.c
ocfs2: Uninline ocfs2_xattr_name_hash()
ocfs2: Don't check for NULL before brelse()
ocfs2: use smaller counters in ocfs2_remove_xattr_clusters_from_cache
ocfs2: Documentation update for user_xattr / nouser_xattr mount options
ocfs2: make la_debug_mutex static
ocfs2: Remove pointless !!
ocfs2: Add empty bucket support in xattr.
ocfs2/xattr.c: Fix a bug when inserting xattr.
ocfs2: Add xattr mount option in ocfs2_show_options()
ocfs2: Switch over to JBD2.
ocfs2: Add the 'inode64' mount option.
...
|
|
Add compat option to hid code to allow loading of all modules on
systems which don't allow autoloading because of old userspace.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
