| Age | Commit message (Collapse) | Author |
|---|
|
ovs_flow_cmd_del() now allocates reply (if needed) after the flow has
already been removed from the flow table. If the reply allocation
fails, a netlink error is signaled with netlink_set_err(), as is
already done in ovs_flow_cmd_new_or_set() in the similar situation.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Reduce and clarify locking requirements for ovs_flow_cmd_alloc_info(),
ovs_flow_cmd_fill_info() and ovs_flow_cmd_build_info().
A datapath pointer is available only when holding a lock. Change
ovs_flow_cmd_fill_info() and ovs_flow_cmd_build_info() to take a
dp_ifindex directly, rather than a datapath pointer that is then
(only) used to get the dp_ifindex. This is useful, since the
dp_ifindex is available even when the datapath pointer is not, both
before and after taking a lock, which makes further critical section
reduction possible.
Make ovs_flow_cmd_alloc_info() take an 'acts' argument instead a
'flow' pointer. This allows some future patches to do the allocation
before acquiring the flow pointer.
The locking requirements after this patch are:
ovs_flow_cmd_alloc_info(): May be called without locking, must not be
called while holding the RCU read lock (due to memory allocation).
If 'acts' belong to a flow in the flow table, however, then the
caller must hold ovs_mutex.
ovs_flow_cmd_fill_info(): Either ovs_mutex or RCU read lock must be held.
ovs_flow_cmd_build_info(): This calls both of the above, so the caller
must hold ovs_mutex.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
For ovs_flow_stats_get() using ovsl_dereference() was wrong, since
flow dumps call this with RCU read lock.
ovs_flow_stats_clear() is always called with ovs_mutex, so can use
ovsl_dereference().
Also, make the ovs_flow_stats_get() 'flow' argument const to make
later patches cleaner.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Incorrect struct name was confusing, even though otherwise
inconsequental.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Move most memory allocations away from the ovs_mutex critical
sections. vport allocations still happen while the lock is taken, as
changing that would require major refactoring. Also, vports are
created very rarely so it should not matter.
Change ovs_dp_cmd_get() now only takes the rcu_read_lock(), rather
than ovs_lock(), as nothing need to be changed. This was done by
ovs_vport_cmd_get() already.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Masks are inserted when flows are inserted to the table, so it is
logical to correspondingly remove masks when flows are removed from
the table, in ovs_flow_table_remove().
This allows ovs_flow_free() to be called without locking, which will
be used by later patches.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Use netlink_has_listeners() and NLM_F_ECHO flag to determine if a
reply is needed or not for OVS_FLOW_CMD_NEW, OVS_FLOW_CMD_SET, or
OVS_FLOW_CMD_DEL. Currently, OVS userspace does not request a reply
for OVS_FLOW_CMD_NEW, but usually does for OVS_FLOW_CMD_DEL, as stats
may have changed.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Remove unnecessary locking from functions that are always called with
appropriate locking.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Thomas Graf <tgraf@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Flow SET can accept an empty set of actions, with the intended
semantics of leaving existing actions unmodified. This seems to have
been brokin after OVS 1.7, as we have assigned the flow's actions
pointer to NULL in this case, but we never check for the NULL pointer
later on. This patch restores the intended behavior and documents it
in the include/linux/openvswitch.h.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Minimize padding in sw_flow_key and move 'tp' top the main struct.
These changes simplify code when accessing the transport port numbers
and the tcp flags, and makes the sw_flow_key 8 bytes smaller on 64-bit
systems (128->120 bytes). These changes also make the keys for IPv4
packets to fit in one cache line.
There is a valid concern for safety of packing the struct
ovs_key_ipv4_tunnel, as it would be possible to take the address of
the tun_id member as a __be64 * which could result in unaligned access
in some systems. However:
- sw_flow_key itself is 64-bit aligned, so the tun_id within is
always
64-bit aligned.
- We never make arrays of ovs_key_ipv4_tunnel (which would force
every
second tun_key to be misaligned).
- We never take the address of the tun_id in to a __be64 *.
- Whereever we use struct ovs_key_ipv4_tunnel outside the
sw_flow_key,
it is in stack (on tunnel input functions), where compiler has full
control of the alignment.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Diana Craciun <diana.craciun@freescale.com>
|
|
We get an array of instructions from the hypervisor via device tree that
we write into a buffer that gets executed whenever we want to make an
ePAPR compliant hypercall.
However, the hypervisor passes us these instructions in BE order which
we have to manually convert to LE when we want to run them in LE mode.
With this fixup in place, I can successfully run LE kernels with KVM
PV enabled on PR KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
- BSC9132 is an integrated device that targets Femto base station market.
It combines Power Architecture e500v2 and DSP StarCore SC3850 technologies
with MAPLE-B2F baseband acceleration processing elements
- BSC9132QDS Overview
2Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
SD slot
eTSEC1: Connected to SGMII PHY
eTSEC2: Connected to SGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
P1023RDS is no longer supported/manufactured by Freescale while P1023RDB is.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Besides other potential problems, if MPIC_NO_RESET is not set,
the error interrupt will be masked after it is requested.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Add support for T104x board in board file t104x_qds.c, It is common for
both T1040 and T1042 as they share same QDS board.
T1040QDS board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors (T1040 only)
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types.
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep (T1040 only)
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Add T104xQDS support in Kconfig and Makefile. Also create device tree.
Following features are currently not implmented.
- SerDes: Aurora
- IFC: GASIC, Promjet
- QIXIS
- Ethernet
- DIU
- power supplies management
- ProfiBus
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
processor cores with high-performance data path acceleration architecture
and network peripheral interfaces required for networking & telecommunications.
T1042 personality is a reduced personality of T1040 without Integrated 8-port
Gigabit Ethernet switch.
The T1040/T1042 SoC includes the following function and features:
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration (SEC 5.0)
- RegEx Pattern Matching Acceleration (PME 2.2)
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch (T1040 only)
- Four 1 Gbps Ethernet controllers
- Two RGMII interfaces or one RGMII and one MII interfaces
- High speed peripheral interfaces
- Four PCI Express 2.0 controllers running at up to 5 GHz
- Two SATA controllers supporting 1.5 and 3.0 Gb/s operation
- Upto two QSGMII interface
- Upto six SGMII interface supporting 1000 Mbps
- One SGMII interface supporting upto 2500 Mbps
- Additional peripheral interfaces
- Two USB 2.0 controllers with integrated PHY
- SD/eSDHC/eMMC
- eSPI controller
- Four I2C controllers
- Four UARTs
- Four GPIO controllers
- Integrated flash controller (IFC)
- Change this to LCD/ HDMI interface (DIU) with 12 bit dual data rate
- TDM interface
- Multicore programmable interrupt controller (PIC)
- Two 8-channel DMA engines
- Single source clocking implementation
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Updated the device trees according to the corenet-cf
binding definition.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Updated the device trees according to the corenet-cf
binding definition.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
The CoreNet coherency fabric is a fabric-oriented, conectivity
infrastructure that enables the implementation of coherent, multicore
systems. The CCF acts as a central interconnect for cores,
platform-level caches, memory subsystem, peripheral devices and I/O host
bridges in the system.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
[scottwood@freescale.com: formatting and minor changes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This warning can be seen in allyesconfig, and was introduced by commit
f9eb581c63b2acce827570e105205c0789360650 "powerpc: fix build of
epapr_paravirt on 64-bit book3s".
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This fixes an allyesconfig build break introduced by commit
7762b1ed7aaee223230793fcee80672e2e3aa7a8 "powerpc: move epapr paravirt
init of power_save to an initcall".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
|
|
Main changs include:
- Clarified the clock nodes' version number
- Fixed a issue in example
Singed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
some restructuring of epapr paravirt init resulted in
ppc_md.power_save being set, and then overwritten to
NULL during machine_init. This patch splits the
initialization of ppc_md.power_save out into a postcore
init call.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
OCA4080 overview:
- 1.466 GHz Freescale QorIQ P4080E Processor
- 4Gbyte DDR3 on board
- 8Mbyte Nor flash
- Serial RapidIO 1.2
- 1 x 10/100/1000 BASE-T front ethernet
- 1 x 1000 BASE-BX ethernet on AMC connector
Signed-off-by: Martijn de Gouw <martijn.de.gouw@prodrive.nl>
[scottwood@freescale.com: minor conflict-related changes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This patch introduces the support for Keymile's kmcoge4 board which is
the internal reference design for boards based on Freescale's
P2040/P2041 SoCs. This internal reference design is named kmp204x.
The peripherals used on this board are:
- SPI NOR Flash as bootloader medium
- NAND Flash with a ubi partition
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 4 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
CPLD
- 2 I2C busses
- last but not least, the mandatory serial port
The patch also adds a defconfig file for this reference design that is
necessary because of the lowmem option that must be set higher due to
the number of PCIe devices with big ioremapped mem ranges on the boad.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
These are the bindings for 2 MFD devices used on some of the Keymile boards.
The first one is the chassis managmenet bfticu FPGA.
The second one is the board controller (reset, LEDs, GPIOs) QRIO CPDL.
These FPGAs are used in the kmcoge4 board.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Even though the company belongs to Microsemi, many chips are still
labeled as Zarlink. Among them is the family of network clock generators,
the zl3034x.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
PCI controller disable PME message report feature, that shouldn't
have happened. Fix it and enable PME message report feature.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
There are error parameters should be corrected when
calling dma_free_coherent to free rmu rx-ring buffers
in fsl_open_inb_mbox() function.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
The only way Freescale booke chips support mappings larger than 4K
is via TLB1. The only way we support (direct) TLB1 entries is via
hugetlb, which is not what map_kernel_page() does when given a large
page size.
Without this, a kernel with CONFIG_SPARSEMEM_VMEMMAP enabled crashes on
boot with messages such as:
PID hash table entries: 4096 (order: 3, 32768 bytes)
Sorting __ex_table...
BUG: Bad page state in process swapper pfn:00a2f
page:8000040000023a48 count:0 mapcount:0 mapping:0000040000ffce48 index:0x40000ffbe50
page flags: 0x40000ffda40(active|arch_1|private|private_2|head|tail|swapcache|mappedtodisk|reclaim|swapbacked|unevictable|mlocked)
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags:
page flags: 0x311840(active|private|private_2|swapcache|unevictable|mlocked)
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.15.0-rc1-00003-g7fa250c #299
Call Trace:
[c00000000098ba20] [c000000000008b3c] .show_stack+0x7c/0x1cc (unreliable)
[c00000000098baf0] [c00000000060aa50] .dump_stack+0x88/0xb4
[c00000000098bb70] [c0000000000c0468] .bad_page+0x144/0x1a0
[c00000000098bc10] [c0000000000c0628] .free_pages_prepare+0x164/0x17c
[c00000000098bcc0] [c0000000000c24cc] .free_hot_cold_page+0x48/0x214
[c00000000098bd60] [c00000000086c318] .free_all_bootmem+0x1fc/0x354
[c00000000098be70] [c00000000085da84] .mem_init+0xac/0xdc
[c00000000098bef0] [c0000000008547b0] .start_kernel+0x21c/0x4d4
[c00000000098bf90] [c000000000000448] .start_here_common+0x20/0x58
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Two issues:
o For beql_op, beql_op, bne_op, bnel_op, blez_op, blezl_op, bgtz_op and
bgtzl_op the wrong field was being checked for the instruction opcode.
o For blez_op / blezl_op and bgtz_op / bgtzl_op the test was testing
for the wrong opcode.
This bug got introduced by d8d4e3ae0b5c179c0bfd3f0af5b352d13bea9cfa [MIPS
Kprobes: Refactor branch emulation].
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Acked-by: Victor Kamensky <kamensky@cisco.com>
|
|
The way the driver core is implemented, every device using the same bus
type is required to have a unique name because a symlink to each device
is created in the appropriate /sys/bus/*/devices directory, and two
identical names causes a collision.
The current code handles the requirement by using an globally
incremented counter that is appended to the device name. It works, but
it means any change to device registration will change the assigned
numbers. Instead, if we build up the name by using information from the
parent nodes, then it can be guaranteed to be unique without adding a
random number to the end of it.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Cc: Rob Herring <robh@kernel.org>
|
|
This patch adds of_clk_get_by_clkspec() helper function, which does only
a struct clk lookup from the clock providers. It is used in the subsequent
patch where parsing of a clock from device tree and the lookup from
providers needed to be split.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The recent change in sysfs, bcdde7e221a8750f9b62b6d0bd31b72ea4ad9309
"sysfs: make __sysfs_remove_dir() recursive" revealed an asymmetric
rphy device creation/deletion sequence in scsi_transport_sas:
modprobe mpt2sas
sas_rphy_add
device_add A rphy->dev
device_add B sas_device transport class
device_add C sas_end_device transport class
device_add D bsg class
rmmod mpt2sas
sas_rphy_delete
sas_rphy_remove
device_del B
device_del C
device_del A
sysfs_remove_group recursive sysfs dir removal
sas_rphy_free
device_del D warning
where device A is the parent of B, C, and D.
When sas_rphy_free tries to unregister the bsg request queue (device D
above), the ensuing sysfs cleanup discovers that its sysfs group has
already been removed and emits a warning, "sysfs group... not found for
kobject 'end_device-X:0'".
Since bsg creation is a side effect of sas_rphy_add, move its
complementary removal call into sas_rphy_remove. This imposes the
following tear-down order for the devices above: D, B, C, A.
Note the sas_device and sas_end_device transport class devices (B and C
above) are created and destroyed both via the list match traversal in
attribute_container_device_trigger, so the order in which they are
handled is fixed. This is fine as long as they are deleted before their
parent device.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This switches the Qualcomm MSM pin control driver over to using
the generic GPIO irqchip helpers.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When the support for the PRCM muxer on the A31 has been added, the global
static pinctl_desc definition has been left as is. Unfortunately, this
structure is used to register the pinctrl device, and prior to this
registration, we set the name and pins field.
Since this structure is shared across instances, that means that the latest
registered pinctrl device wins in setting the name, pins and pins numbers,
which is not really a good thing.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix the following configuration error:
drivers/pinctrl/sunxi/Kconfig:3:error: recursive dependency detected!
drivers/pinctrl/sunxi/Kconfig:3: symbol PINCTRL_SUNXI is selected by PINCTRL_SUN4I_A10
drivers/pinctrl/sunxi/Kconfig:9: symbol PINCTRL_SUN4I_A10 default value contains PINCTRL_SUNXI
Add a new intermedia PINCTRL_SUNXI_COMMON, that superseeds the PINCTRL_SUNXI
one.
We still need to keep PINCTRL_SUNXI at the moment in order to preserve
bisectability. Indeed, during that merge window, we also introduced the
MACH_SUN* symbols. Since it's going through different trees, we can't rely on
the fact that the options will be there, while ARCH_SUNXI still select
PINCTRL_SUNXI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the pin-controller driver for the Berlin BG2Q SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the pin-controller driver for the Berlin BG2 SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the pin-controller driver for the Berlin BG2Q SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Marvell Berlin boards have a group based pinmuxing mechanism. This
adds the core driver support. We actually do not need any information
about the pins here and only have the definition of the groups.
Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and
BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set
to mode 0:
Group Modes Offset Base Offset LSB Bit Width
GSM12 3 sm_base 0x40 0x10 0x2
Ball Group Mode 0 Mode 1 Mode 2
BK4 GSM12 UART0_RX IrDA0_RX GPIO9
BH6 GSM12 UART0_TX IrDA0_TX GPIO10
So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need
to set (sm_base + 0x40 + 0x10) &= ff3fffff.
As pin control registers are part of either chip control or system
control registers, that deal with a bunch of other functions we rely
on a regmap instead of exclusively remapping any resources.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In case of resolving power management or similar issues it might be useful
to have these properties included in the debugfs output.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If chip->to_irq is NULL ACPI GPIO helpers don't register GPIO event
handlers thus preventing any ACPI GPIO triggered events. Solve this by
calling gpiochip_add() after we have set up drivers chip->to_irq hook.
Signed-off-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that the x86 dynamic IRQ allocation problem has been resolved with
commmit 62a08ae2a576 (genirq: x86: Ensure that dynamic irq allocation does
not conflict), we can add back Baytrail-T ACPI ID to the pinctrl driver.
This makes the driver to work on Asus T100 where it is needed for several
things like ACPI GPIO events and SD card detection.
References: https://bugzilla.kernel.org/show_bug.cgi?id=68291
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add #ifdefs to allow r8a73a4 Multiplatform build. Needed
to enable r8a73a4 Multiplatform support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add #ifdefs to allow sh73a0 Multiplatform build. Needed
to enable sh73a0 Multiplatform support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add #ifdefs to allow r8a7740 Multiplatform build. Needed
to enable r8a7740 Multiplatform support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In the multiplatform kernel case the IRQs associated with the PFC GPIOs
are specified through DT. The pinmux_irq irq field is thus ignored by
the code, and doesn't need to be set.
This will allow removing the mach/irq.h include from pfc-*.c files that
was required for the irq_pin() macro used to initialize the irq field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Enable the freshly introduced Kconfig options whenever their matching
architecture is enabled.
Since the Kconfig symbols for these machines are going through a different
tree, keep PINCTRL_SUNXI around for the moment to avoid breaking the defconfig.
It should be removed eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
