Age | Commit message (Collapse) | Author |
|
Azurit reports large increases in system time after 2.6.36 when running
Apache. It was bisected down to a892e2d7dcdfa6c76e6 ("vfs: use kmalloc()
to allocate fdmem if possible").
That patch caused the vfs to use kmalloc() for very large allocations and
this is causing excessive work (and presumably excessive reclaim) within
the page allocator.
Fix it by falling back to vmalloc() earlier - when the allocation attempt
would have been considered "costly" by reclaim.
Reported-by: azurIt <azurit@pobox.sk>
Tested-by: azurIt <azurit@pobox.sk>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds support for the Terratec Aureon 7.1 USB which uses a
C-Media cm6206 and needs all the quirks already found in the past.
Signed-off-by: Wolfgang Breyha <wbreyha@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The USB and SATA ioapic interrrupt pins are configured as edge type,
but need to be level type interrupts to work correctly.
[ tglx: Split out from the combo patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We use io_apic_setup_irq_pin() in order to configure pin's interrupt
number polarity and type. This is done on every irq_create_of_mapping()
which happens for instance during pci enable calls. Level typed
interrupts are masked by default, edge are unmasked.
On the first ->xlate() call the level interrupt is configured and
masked. The driver calls request_irq() and the line is unmasked. Lets
assume the interrupt line is shared with another device and we call
pci_enable_device() for this device. The ->xlate() configures the pin
again and it is masked. request_irq() does not unmask the line because
it _is_ already unmasked according to its internal state. So the
interrupt will never be unmasked again.
This patch is based on an earlier work by Torben Hohn and solves the
problem by configuring the pin only once. Since all devices must agree
on the same type and polarity there is no point in configuring the pin
more than once.
[ tglx: Split out the ce4100 part into a separate patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In notify_aa_path_ctls(), adds 'rear mic' item and confirms the A-A
path control existing before notifying card that the A-A path volume
is muted if smart5.1 is enabled.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We call rtc_read_alarm from rtc_device_register, so it is important
that the rtc device is fully initialized prior to registration.
rtc-max8925 sets drvdata after register, so the rtc_read_alarm code
dereferences a NULL pointer.
Call dev_set_drvdata before rtc_device_register.
[ jstultz/tglx: Massaged commit message ]
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Link: http://lkml.kernel.org/r/%3C1303929869-25249-1-git-send-email-john.stultz%40linaro.org%3E
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] slub: fix panic with DISCONTIGMEM
[PARISC] set memory ranges in N_NORMAL_MEMORY when onlined
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
ACPI / PM: Avoid infinite recurrence while registering power resources
PM / Wakeup: Fix initialization of wakeup-related device sysfs files
|
|
* 'spell-fix' of git://git.profusion.mobi/users/lucas/linux-2.6:
Revert wrong fixes for common misspellings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
|
|
On a remount, the VFS layer will clear the MS_SYNCHRONOUS bit on the
assumption that the flags on the mount syscall will have it set if the
remounted fs is supposed to keep it.
In the case of "noac" though, MS_SYNCHRONOUS is implied. A remount of
such a mount will lose the MS_SYNCHRONOUS flag since "sync" isn't part
of the mount options.
Reported-by: Max Matveev <makc@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
When compiling, I was getting this warning:
fs/nfs/nfs4xdr.c: In function ‘decode_secinfo’:
fs/nfs/nfs4xdr.c:4839:6: warning: variable ‘status’ set but not used
[-Wunused-but-set-variable]
We were unconditionally returning 0 as long as there wasn't an error
coming out of xdr_inline_decode(). We probably want to check the error
status coming out of decode_op_hdr() and decode_secinfo_gss(), rather
than assuming that everything is OK all the time.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
When readdir() returns a directory entry for the root of a mounted
filesystem, Linux follows the old convention of returning the inode
number of the covered directory (despite newer versions of POSIX declaring
that this is a bug).
To ensure this continues to work, the NFSv4 readdir implementation requests
the 'mounted-on-fileid' from the server.
However, readdirplus also needs to instantiate an inode for this entry, and
for that, we also need to request the real fileid as per this patch.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
It was noticed that P4 machines were generating double NMIs for
each perf event. These extra NMIs lead to 'Dazed and confused'
messages on the screen.
I tracked this down to a P4 quirk that said the overflow bit had
to be cleared before re-enabling the apic LVT mask. My first
attempt was to move the un-masking inside the perf nmi handler
from before the chipset NMI handler to after.
This broke Nehalem boxes that seem to like the unmasking before
the counters themselves are re-enabled.
In order to keep this change simple for 2.6.39, I decided to
just simply move the apic LVT un-masking to the beginning of all
the chipset NMI handlers, with the exception of Pentium4's to
fix the double NMI issue.
Later on we can move the un-masking to later in the handlers to
save a number of 'extra' NMIs on those particular chipsets.
I tested this change on a P4 machine, an AMD machine, a Nehalem
box, and a core2quad box. 'perf top' worked correctly along
with various other small 'perf record' runs. Anything high
stress breaks all the machines but that is a different problem.
Thanks to various people for testing different versions of this
patch.
Reported-and-tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303900353-10242-1-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CC: Cyrill Gorcunov <gorcunov@gmail.com>
|
|
For m68k, N_NORMAL_MEMORY represents all nodes that have present memory
since it does not support HIGHMEM. This patch sets the bit at the time
node_present_pages has been set by free_area_init_node.
At the time the node is brought online, the node state would have to be
done unconditionally since information about present memory has not yet
been recorded.
If N_NORMAL_MEMORY is not accurate, slub may encounter errors since it
uses this nodemask to setup per-cache kmem_cache_node data structures.
This pach is an alternative to the one proposed by David Rientjes
<rientjes@google.com> attempting to set node state immediately when
bringing the node online.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Tested-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
CC: stable@kernel.org
|
|
This allow application such as gstreamer and wine which use
snd_pcm_hw_params_set_buffer_time_near() won't fail any more
since sound chips require special containt power 2 period bytes
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
devel-fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into perf/urgent
|
|
i915 calls the panic handler function on last close to reset the modes,
however this is a really bad idea for multi-gpu machines, esp shareable
gpus machines. So add a new entry point for the driver to just restore
its own fbcon mode.
v2: move code into fb helper, fix panic code to block mode change on
powered off GPUs.
[airlied: this hits drm core and I wrote it and it was reviewed on intel-gfx
so really I signed it off twice ;-).]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The git commit c708c57e247775928b9a6bce7b4d8d14883bf39b fixed the
access beyond the end of the stack in prng_seed but the pointer
arithmetic is still incorrect. The calculation has been off by
a factor of 64, now it is only off by a factor of 8. prng_seed
is called with a maximum of 16 for nbytes, small enough that
the incorrect calculation stays insides the limits of the stack.
Place parentheses for correct pointer arithmetic.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
needed by mesa for htile setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
needed for HiS in mesa.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Multi-gpu/switcheroo relies on this option to get the console on the
correct GPU at bootup, some distros enable it but it seems some get
it wrong.
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
These changes were incorrectly fixed by codespell. They were now
manually corrected.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
|
|
The EXPERT menu list was recently broken by the insertion of a
kconfig symbol (EMBEDDED) at the beginning of the EXPERT list of
kconfig items. Broken by:
commit 6a108a14fa356ef607be308b68337939e56ea94e
Author: David Rientjes <rientjes@google.com>
Date: Thu Jan 20 14:44:16 2011 -0800
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
Restore the EXPERT menu list -- don't inject a symbol (EMBEDDED)
that does not depend on EXPERT into the list.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Peter Foley <pefoley2@verizon.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch exposes alarm-timers to userland via the posix clock
and timers interface, using two new clockids: CLOCK_REALTIME_ALARM
and CLOCK_BOOTTIME_ALARM. Both clockids behave identically to
CLOCK_REALTIME and CLOCK_BOOTTIME, respectively, but timers
set against the _ALARM suffixed clockids will wake the system if
it is suspended.
Some background can be found here:
https://lwn.net/Articles/429925/
The concept for Alarm-timers was inspired by the Android Alarm
driver (by Arve Hjønnevåg) found in the Android kernel tree.
See: http://android.git.kernel.org/?p=kernel/common.git;a=blob;f=drivers/rtc/alarm.c;h=1250edfbdf3302f5e4ea6194847c6ef4bb7beb1c;hb=android-2.6.36
While the in-kernel interface is pretty similar between
alarm-timers and Android alarm driver, the user-space interface
for the Android alarm driver is via ioctls to a new char device.
As mentioned above, I've instead chosen to export this functionality
via the posix interface, as it seemed a little simpler and avoids
creating duplicate interfaces to things like CLOCK_REALTIME and
CLOCK_MONOTONIC under alternate names (ie:ANDROID_ALARM_RTC and
ANDROID_ALARM_SYSTEMTIME).
The semantics of the Android alarm driver are different from what
this posix interface provides. For instance, threads other then
the thread waiting on the Android alarm driver are able to modify
the alarm being waited on. Also this interface does not allow
the same wakelock semantics that the Android driver provides
(ie: kernel takes a wakelock on RTC alarm-interupt, and holds it
through process wakeup, and while the process runs, until the
process either closes the char device or calls back in to wait
on a new alarm).
One potential way to implement similar semantics may be via
the timerfd infrastructure, but this needs more research.
There may also need to be some sort of sysfs system level policy
hooks that allow alarm timers to be disabled to keep them
from firing at inappropriate times (ie: laptop in a well insulated
bag, mid-flight).
CC: Arve Hjønnevåg <arve@android.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
This provides the in kernel interface and infrastructure for
alarm-timers.
Alarm-timers are a hybrid style timer, similar to hrtimers,
but when the system is suspended, the RTC device is set to
fire and wake the system for when the soonest alarm-timer
expires.
The concept for Alarm-timers was inspired by the Android Alarm
driver (by Arve Hjønnevåg) found in the Android kernel tree.
See: http://android.git.kernel.org/?p=kernel/common.git;a=blob;f=drivers/rtc/alarm.c;h=1250edfbdf3302f5e4ea6194847c6ef4bb7beb1c;hb=android-2.6.36
This in-kernel interface should be fairly compatible with the
Android alarm driver in-kernel interface, but has the advantage
of utilizing the new RTC timerqueue code instead of doing direct
RTC manipulation.
CC: Arve Hjønnevåg <arve@android.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
In cases where a timerqueue_node or some structure that utilizes
a timerqueue_node is allocated on the stack, gcc would give warnings
caused by the timerqueue_init()'s calling RB_CLEAR_NODE, which
self-references the nodes uninitialized data.
The solution is to create an rb_init_node() function that zeros
the rb_node structure out and then calls RB_CLEAR_NODE(), and
then call the new init function from timerqueue_init().
CC: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Some platforms cannot implement read_persistent_clock, as
their RTC devices are only accessible when interrupts are enabled.
This keeps them from being used by the timekeeping code on resume
to measure the time in suspend.
The RTC layer tries to work around this, by calling do_settimeofday
on resume after irqs are reenabled to set the time properly. However,
this only corrects CLOCK_REALTIME, and does not properly adjust
the sleep time value. This causes btime in /proc/stat to be incorrect
as well as making the new CLOCK_BOTTTIME inaccurate.
This patch resolves the issue by introducing a new timekeeping hook
to allow the RTC layer to inject the sleep time on resume.
The code also checks to make sure that read_persistent_clock is
nonfunctional before setting the sleep time, so that should the RTC's
HCTOSYS option be configured in on a system that does support
read_persistent_clock we will not increase the total_sleep_time twice.
CC: Arve Hjønnevåg <arve@android.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Erratum #637 workaround
amd64_edac: Factor in CC6 save area
amd64_edac: Remove node interleave warning
EDAC: Remove debugging output in scrub rate handling
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: iTCO_wdt: TCO Watchdog patch for Intel Panther Point PCH
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] kvm-390: Let kernel exit SIE instruction on work
[S390] dasd: check sense type in device change handler
[S390] pfault: fix token handling
[S390] qdio: reset error states immediately
[S390] fix page table walk for changing page attributes
[S390] prng: prevent access beyond end of stack
[S390] dasd: fix race between open and offline
|
|
On Nehalem CPUs the retired branch-misses event can be completely bogus,
when there are no branch-misses occuring. When there are a lot of branch
misses then the count is pretty accurate. Still, this leaves us with an
event that over-counts a lot.
Detect this erratum and work it around by using BR_MISP_EXEC.ANY events.
These will also count speculated branches but still it's a lot more
precise in practice than the architectural event.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-yyfg0bxo9jsqxd6a0ovfny27@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: cleanup error handling in inode.c
Btrfs: put the right bio if we have an error
Btrfs: free bitmaps properly when evicting the cache
Btrfs: Free free_space item properly in btrfs_trim_block_group()
btrfs: add missing spin_unlock to a rare exit path
Btrfs: check return value of kmalloc()
btrfs: fix wrong allocating flag when reading page
Btrfs: fix missing mutex_unlock in btrfs_del_dir_entries_in_log()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: do some plugging in the submit_bio threads
|
|
F15h CPUs may report a non-DRAM address when reporting an error address
belonging to a CC6 state save area. Add a workaround to detect this
condition and compute the actual DRAM address of the error as documented
in the Revision Guide for AMD Family 15h Models 00h-0Fh Processors.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
F15h and later use a portion of DRAM as a CC6 storage area. BIOS
programs D18F1x[17C:140,7C:40] DRAM Base/Limit accordingly by
subtracting the storage area from the DRAM limit setting. However, in
order for edac to consider that part of DRAM too, we need to include it
into the per-node range.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
This warning was wrongfully added for a normal condition - intlvsel
actually selects the destination node when node interleaving is enabled
and it is not a mismatch. For a detailed example, see section 2.8.10.2
"Node Interleaving" in F10h BKDG.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
This patch adds the TCO Watchdog DeviceIDs for the Intel Panther Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Currently the x86 backend incorrectly assumes that any BRANCH_INSN
with sample_period==1 is a BTS request. This is not true when we do
frequency driven profiling such as 'perf record -e branches'.
Solves this error:
$ perf record -e branches ./array
Error: sys_perf_event_open() syscall returned with 95 (Operation not supported).
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: "Metzger, Markus T" <markus.t.metzger@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-rd2y4ct71hjawzz6fpvsy9hg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Blindly setting 1.2V in the initial structure may not even match the
default voltages stored in the voltage table which are supported for
the domain. For example, OMAP3430 core domain does not use 1.2V and
ends up generating a warning on the first transition.
Further, since omap2_set_init_voltage is called as part of the pm
framework's initialization sequence to configure the voltage required
for the current OPP, the call does(and has to) setup the system
voltage(curr_volt as a result) using the right mechanisms appropriate
for the system at that point of time. This also overrides
initialization we are currently doing in voltage.c making it
redundant. So, remove the wrong and redundant initialization.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP4 has two different Devices IVA and DSP. DSP is bound
with IVA for DVFS. The registration of IVA dev in API
'omap2_init_processor_devices' was missing. Init dev for
'iva_dev' is added.
This also fixes the following error seen during boot as
omap2_set_init_voltage can now find the iva device
omap2_set_init_voltage: Invalid parameters!
omap2_set_init_voltage: Unable to put vdd_iva to its init voltage
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
So that omap_vram_set_sdram_vram() is called before
omap_vram_reserve_sdram_memblock().
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is at least one BIOS with a DSDT containing a power resource
object with a _PR0 entry pointing back to that power resource. In
consequence, while registering that power resource
acpi_bus_get_power_flags() sees that it depends on itself and tries
to register it again, which leads to an infinitely deep recurrence.
This problem was introduced by commit bf325f9538d8c89312be305b9779e
(ACPI / PM: Register power resource devices as soon as they are
needed).
To fix this problem use the observation that power resources cannot
be power manageable and prevent acpi_bus_get_power_flags() from
being called for power resource objects.
References: https://bugzilla.kernel.org/show_bug.cgi?id=31872
Reported-and-tested-by: Pascal Dormeau <pdormeau@free.fr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <lenb@kernel.org>
Cc: stable@kernel.org
|
|
It turns out that some PCI devices are only found to be
wakeup-capable during registration, in which case, when
device_set_wakeup_capable() is called, device_is_registered() already
returns 'true' for the given device, but dpm_sysfs_add() hasn't been
called for it yet. This leads to situations in which the device's
power.can_wakeup flag is not set as requested because of failing
wakeup_sysfs_add() and its wakeup-related sysfs files are not
created, although they should be present. This is a post-2.6.38
regression introduced by commit cb8f51bdadb7969139c2e39c2defd4cde98c1
(PM: Do not create wakeup sysfs files for devices that cannot wake
up).
To work around this problem initialize the device's power.entry
field to an empty list head and make device_set_wakeup_capable()
check if it is still empty before attempting to add the devices
wakeup-related sysfs files with wakeup_sysfs_add(). Namely, if
power.entry is still empty at this point, device_pm_add() hasn't been
called yet for the device and its wakeup-related files will be
created later, so device_set_wakeup_capable() doesn't have to create
them.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If an error occurs in the L3 on any other initiator than MPU,
the interrupt goes unhandled given that the 'base' register
was calculated with the initialized err_source value (which
coincidentally points to MPU) and not with the actual source
of the error.
Removed parenthesis that are not needed for the touched lines.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This fixes broken build when using binutils 2.21.
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
CIFS: Fix memory over bound bug in cifs_parse_mount_options
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
eCryptfs: Flush dirty pages in setattr
eCryptfs: Handle failed metadata read in lookup
eCryptfs: Add reference counting to lower files
eCryptfs: dput dentries returned from dget_parent
eCryptfs: Remove extra d_delete in ecryptfs_rmdir
|