| Age | Commit message (Collapse) | Author |
|---|
|
Based on a patch from Mike McElroy created against the out-of-tree e1000e
driver:
Hitting the BUG_ON in napi_enable(). Code inspection shows that this can
only be triggered by calling napi_enable() twice without an intervening
napi_disable().
I saw the following sequence of events in the stack trace:
1) We simulated a cable pull using an Extreme switch.
2) e1000_tx_timeout() was entered.
3) e1000_reset_task() was called. Saw the message from e_err() in the
console log.
4) e1000_reinit_locked was called. This function calls e1000_down() and
e1000_up(). These functions call napi_disable() and napi_enable()
respectively.
5) Then on another thread, a monitor task saw carrier was down and executed
'ip set link down' and 'ip set link up' commands.
6) Saw the '_E1000_RESETTING'warning fron the e1000_close function.
7) Either the e1000_open() executed between the e1000_down() and e1000_up()
calls in step 4 or the e1000_open() call executed after the e1000_up()
call. In either case, napi_enable() is called twice which triggers the
BUG_ON.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Mike McElroy <mike.mcelroy@stratus.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on the original patch submitted my Michael Wang
<wangyun@linux.vnet.ibm.com>.
Descriptors may not be write-back while checking TX hang with flag
FLAG2_DMA_BURST on.
So when we detect hang, we just flush the descriptor and detect
again for once.
-v2 change 1 to true and 0 to false and remove extra ()
CC: Michael Wang <wangyun@linux.vnet.ibm.com>
CC: Flavio Leitner <fbl@redhat.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
People with old AMD chips are getting hung boots, because commit
bcb80e53877c ("x86, microcode, AMD: Add microcode revision to
/proc/cpuinfo") moved the microcode detection too early into
"early_init_amd()".
At that point we are *so* early in the booth that the exception tables
haven't even been set up yet, so the whole
rdmsr_safe(MSR_AMD64_PATCH_LEVEL, &c->microcode, &dummy);
doesn't actually work: if the rdmsr does a GP fault (due to non-existant
MSR register on older CPU's), we can't fix it up yet, and the boot fails.
Fix it by simply moving the code to a slightly later point in the boot
(init_amd() instead of early_init_amd()), since the kernel itself
doesn't even really care about the microcode patchlevel at this point
(or really ever: it's made available to user space in /proc/cpuinfo, and
updated if you do a microcode load).
Reported-tested-and-bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Bob Tracy <rct@gherkin.frus.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If our TCP_PAGE(sk) is not shared (page_count() == 1), we can set page
offset to 0.
This permits better filling of the pages on small to medium tcp writes.
"tbench 16" results on my dev server (2x4x2 machine) :
Before : 3072 MB/s
After : 3146 MB/s (2.4 % gain)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We discovered that TCP stack could retransmit misaligned skbs if a
malicious peer acknowledged sub MSS frame. This currently can happen
only if output interface is non SG enabled : If SG is enabled, tcp
builds headless skbs (all payload is included in fragments), so the tcp
trimming process only removes parts of skb fragments, header stay
aligned.
Some arches cant handle misalignments, so force a head reallocation and
shrink headroom to MAX_TCP_HEADER.
Dont care about misaligments on x86 and PPC (or other arches setting
NET_IP_ALIGN to 0)
This patch introduces __pskb_copy() which can specify the headroom of
new head, and pskb_copy() becomes a wrapper on top of __pskb_copy()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Denys Fedoryshchenko reported that SYN+FIN attacks were bringing his
linux machines to their limits.
Dont call conn_request() if the TCP flags includes SYN flag
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch
|
|
It's only used in net/ipv6/route.c and the NULL device check is
superfluous for all of the existing call sites.
Just expand the __ndisc_lookup_errno() call at each location.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) x == NULL --> !x
2) x != NULL --> x
3) (x&BIT) --> (x & BIT)
4) (BIT1|BIT2) --> (BIT1 | BIT2)
5) proper argument and struct member alignment
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) x == NULL --> !x
2) x != NULL --> x
3) if() --> if ()
4) while() --> while ()
5) (x & BIT) == 0 --> !(x & BIT)
6) (x&BIT) --> (x & BIT)
7) x=y --> x = y
8) (BIT1|BIT2) --> (BIT1 | BIT2)
9) if ((x & BIT)) --> if (x & BIT)
10) proper argument and struct member alignment
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The idea behind commit d91ee5863b71 ("cpuidle: replace xen access to x86
pm_idle and default_idle") was to have one call - disable_cpuidle()
which would make pm_idle not be molested by other code. It disallows
cpuidle_idle_call to be set to pm_idle (which is excellent).
But in the select_idle_routine() and idle_setup(), the pm_idle can still
be set to either: amd_e400_idle, mwait_idle or default_idle. This
depends on some CPU flags (MWAIT) and in AMD case on the type of CPU.
In case of mwait_idle we can hit some instances where the hypervisor
(Amazon EC2 specifically) sets the MWAIT and we get:
Brought up 2 CPUs
invalid opcode: 0000 [#1] SMP
Pid: 0, comm: swapper Not tainted 3.1.0-0.rc6.git0.3.fc16.x86_64 #1
RIP: e030:[<ffffffff81015d1d>] [<ffffffff81015d1d>] mwait_idle+0x6f/0xb4
...
Call Trace:
[<ffffffff8100e2ed>] cpu_idle+0xae/0xe8
[<ffffffff8149ee78>] cpu_bringup_and_idle+0xe/0x10
RIP [<ffffffff81015d1d>] mwait_idle+0x6f/0xb4
RSP <ffff8801d28ddf10>
In the case of amd_e400_idle we don't get so spectacular crashes, but we
do end up making an MSR which is trapped in the hypervisor, and then
follow it up with a yield hypercall. Meaning we end up going to
hypervisor twice instead of just once.
The previous behavior before v3.0 was that pm_idle was set to
default_idle regardless of select_idle_routine/idle_setup.
We want to do that, but only for one specific case: Xen. This patch
does that.
Fixes RH BZ #739499 and Ubuntu #881076
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Open vSwitch is a multilayer Ethernet switch targeted at virtualized
environments. In addition to supporting a variety of features
expected in a traditional hardware switch, it enables fine-grained
programmatic extension and flow-based control of the network.
This control is useful in a wide variety of applications but is
particularly important in multi-server virtualization deployments,
which are often characterized by highly dynamic endpoints and the need
to maintain logical abstractions for multiple tenants.
The Open vSwitch datapath provides an in-kernel fast path for packet
forwarding. It is complemented by a userspace daemon, ovs-vswitchd,
which is able to accept configuration from a variety of sources and
translate it into packet processing rules.
See http://openvswitch.org for more information and userspace
utilities.
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
While parsing through IPv6 extension headers, fragment headers are
skipped making them invisible to the caller. This reports the
fragment offset of the last header in order to make it possible to
determine whether the packet is fragmented and, if so whether it is
a first or last fragment.
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Open vSwitch needs this function for vlan handling.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
This adds rcu_dereference_genl and genl_dereference, which are genl
variants of the RTNL functions to enforce proper locking with lockdep
and sparse.
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Open vSwitch uses genl_mutex locking to protect datapath
data-structures like flow-table, flow-actions. Following patch adds
lockdep_genl_is_held() which is used for rcu annotation to prove
locking.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Open vSwitch uses Generic Netlink interface for communication
between userspace and kernel module. genl_notify() is used
for sending notification back to userspace.
genl_notify() is analogous to rtnl_notify() but uses genl_sock
instead of rtnl.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
__mkroute_output fails to work with the original tos
and uses value with stripped RTO_ONLINK bit. Make sure we put
the original TOS bits into rt_key_tos because it used to match
cached route.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure that code match exactly what comment says about pre 1.2
bluetooth version. Since this is HCI detail lmp_ver changed to hci_ver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Use bluetooth names instead of BT SIG assigned numbers
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth
|
|
Check for hci_ver instead of lmp_ver
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch fixes the following memory leak reported by kmemleak:
unreferenced object 0xffff880060a53840 (size 192):
comm "softirq", pid 0, jiffies 4320571771 (age 1406.569s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff81138a1c>] create_object+0x187/0x28b
[<ffffffff814be12e>] kmemleak_alloc+0x73/0x98
[<ffffffff811289d3>] __kmalloc+0xfc/0x123
[<ffffffff81386546>] usb_alloc_urb+0x1e/0x48
[<ffffffffa0130274>] btusb_send_frame+0x86/0x385 [btusb]
[<ffffffffa02d8230>] hci_send_frame+0xa0/0xa5 [bluetooth]
[<ffffffffa02d8a4e>] hci_cmd_task+0xa0/0xfb [bluetooth]
[<ffffffff81058548>] tasklet_action+0x8f/0xef
[<ffffffff81058a4c>] __do_softirq+0xf4/0x1db
[<ffffffff81058bb7>] run_ksoftirqd+0x84/0x129
[<ffffffff8106f1c4>] kthread+0xa0/0xa8
[<ffffffff814dd144>] kernel_thread_helper+0x4/0x10
[<ffffffffffffffff>] 0xffffffffffffffff
The problem is that when inc_tx() returns non-zero, we forgot
to call usb_free_urb().
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
usb: ftdi_sio: add PID for Propox ISPcable III
Revert "xHCI: reset-on-resume quirk for NEC uPD720200"
xHCI: fix bug in xhci_clear_command_ring()
usb: gadget: fsl_udc: fix dequeuing a request in progress
usb: fsl_mxc_udc.c: Remove compile-time dependency of MX35 SoC type
usb: fsl_mxc_udc.c: Fix build issue by including missing header file
USB: fsl_udc_core: use usb_endpoint_xfer_isoc to judge ISO XFER
usb: udc: Fix gadget driver's speed check in various UDC drivers
usb: gadget: fix g_serial regression
usb: renesas_usbhs: fixup driver speed
usb: renesas_usbhs: fixup gadget.dev.driver when udc_stop.
usb: renesas_usbhs: fixup signal the driver that cable was disconnected
usb: renesas_usbhs: fixup device_register timing
usb: musb: PM: fix context save/restore in suspend/resume path
USB: linux-cdc-acm.inf: add support for the acm_ms gadget
EHCI : Fix a regression in the ISO scheduler
xHCI: reset-on-resume quirk for NEC uPD720200
USB: whci-hcd: fix endian conversion in qset_clear()
USB: usb-storage: unusual_devs entry for Kingston DT 101 G2
usb: option: add SIMCom SIM5218
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: comedi: fix integer overflow in do_insnlist_ioctl()
Revert "Staging: comedi: integer overflow in do_insnlist_ioctl()"
Staging: comedi: integer overflow in do_insnlist_ioctl()
Staging: comedi: fix signal handling in read and write
Staging: comedi: fix mmap_count
staging: comedi: fix oops for USB DAQ devices.
staging: comedi: usbduxsigma: Fixed wrong range for the analogue channel.
staging:rts_pstor:Complete scanning_done variable
staging: usbip: bugfix for deadlock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/libertas/cfg.c
|
|
The current default watchdog timer is enabled, but we are seeing issues on
legacy devices. So change the default setting of watchdog timer to per
device based. But user still can use the "wd_disable" module parameter
to overwrite the system setting
Cc: stable@vger.kernel.org #3.0+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ht40 setting should not change after association unless channel switch
This fix a problem we are seeing which cause uCode assert because driver
sending invalid information and make uCode confuse
Here is the firmware assert message:
kernel: iwlagn 0000:03:00.0: Microcode SW error detected. Restarting 0x82000000.
kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301
kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump:
kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6
kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT
kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2
kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1
kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2
kernel: iwlagn 0000:03:00.0: 0x01008035 | data1
kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2
kernel: iwlagn 0000:03:00.0: 0x000005A7 | line
kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time
kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low
kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1
kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3
kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version
kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version
kernel: iwlagn 0000:03:00.0: 0x00480303 | board version
kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd
kernel: iwlagn 0000:03:00.0: CSR values:
kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG)
kernel: iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480303
kernel: iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X0000ff40
kernel: iwlagn 0000:03:00.0: CSR_INT: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000030
kernel: iwlagn 0000:03:00.0: CSR_RESET: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5
kernel: iwlagn 0000:03:00.0: CSR_HW_REV: 0X000000b0
kernel: iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X07d60ffd
kernel: iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000001
kernel: iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00030001
kernel: iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080044
kernel: iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X000093bb
kernel: iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000078
kernel: iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88214dd2
kernel: iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200
kernel: iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a
kernel: iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0010
kernel: iwlagn 0000:03:00.0: FH register values:
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_WPTR: 0X00000060
kernel: iwlagn 0000:03:00.0: FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_STATUS_REG: 0X07030000
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_STATUS_REG: 0X07ff0001
kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_ERROR_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries
kernel: ------------[ cut here ]------------
WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407()
kernel: Hardware name: 4290W4H
kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2
kernel: Call Trace:
kernel: [<ffffffff81036558>] ? warn_slowpath_common+0x73/0x87
kernel: [<ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407
kernel: [<ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32
kernel: [<ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87
kernel: [<ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3
kernel: [<ffffffff810480c9>] ? worker_thread+0x17a/0x23a
kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel: [<ffffffff8104ba97>] ? kthread+0x7a/0x82
kernel: [<ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10
kernel: [<ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11
kernel: [<ffffffff813d21b0>] ? gs_change+0xb/0xb
Cc: <stable@kernel.org> 3.1+
Reported-by: Udo Steinberg <udo@hypervisor.org>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.
Cc: stable@vger.kernel.org
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: fix attr2 vs large data fork assert
xfs: force buffer writeback before blocking on the ilock in inode reclaim
xfs: validate acl count
|
|
Moved netdev_completed_queue() out of while loop in function nv_tx_done_optimized().
Because this function was in while loop,
BUG_ON(count > dql->num_queued - dql->num_completed)
was hit in dql_completed().
Signed-off-by: Igor Maravic <igorm@etf.rs>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Correct General touch PID
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
vmwgfx: integer overflow in vmw_kms_update_layout_ioctl()
drm/radeon/kms: fix 2D tiling CS support on EG/CM
drm/radeon/kms: fix scanout of 2D tiled buffers on EG/CM
drm: Fix lack of CRTC disable for drm_crtc_helper_set_config(.fb=NULL)
drm/radeon/kms: add some new pci ids
drm/radeon/kms: Skip ACPI call to ATIF when possible
drm/radeon/kms: Hide debugging message
drm/radeon/kms: add some loop timeouts in pageflip code
drm/nv50/disp: silence compiler warning
drm/nouveau: fix oopses caused by clear being called on unpopulated ttms
drm/nouveau: Keep RAMIN heap within the channel.
drm/nvd0/disp: fix sor dpms typo, preventing dpms on in some situations
drm/nvc0/gr: fix TP init for transform feedback offset queries
drm/nouveau: add dumb ioctl support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix S3/S4 problem on machines with VREF-pin mute-LED
ALSA: hda_intel - revert a quirk that affect VIA chipsets
ALSA: hda - Avoid touching mute-VREF pin for IDT codecs
firmware: Sigma: Fix endianess issues
firmware: Sigma: Skip header during CRC generation
firmware: Sigma: Prevent out of bounds memory access
ALSA: usb-audio - Support for Roland GAIA SH-01 Synthesizer
ASoC: Supply dcs_codes for newer WM1811 revisions
ASoC: Error out if we can't generate a LRCLK at all for WM8994
ASoC: Correct name of Speyside Main Speaker widget
ASoC: skip resume of soc-audio devices without codecs
ASoC: cs42l51: Fix off-by-one for reg_cache_size
ASoC: drop support for PlayPaq with WM8510
ASoC: mpc8610: tell the CS4270 codec that it's the master
ASoC: cs4720: use snd_soc_cache_sync()
ASoC: SAMSUNG: Fix build error
ASoC: max9877: Update register if either val or val2 is changed
ASoC: Fix wrong define for AD1836_ADC_WORD_OFFSET
|
|
If a device is shutdown, then there might be a pending interrupt,
which will be processed after we reenable interrupts, which causes the
original handler to be run. If the old handler is the (broadcast)
periodic handler the shutdown state might hang the kernel completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
When a better rated broadcast device is installed, then the current
active device is not disabled, which results in two running broadcast
devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
Remove old code not touched for several years.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds the parameter struct and the command complete event
handler to the LE Set Scan Parameter HCI command.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds the dev_flags field to struct hci_dev. This new
flags variable should be used to define flags related to BR/EDR
and/or LE controller itself. It should be used to define flags
which represents states from the controller. The dev_flags is
cleared in case the controller sends a Reset Command Complete
Event to the host.
Also, this patch adds the HCI_LE_SCAN flag which was created to
track if the controller is performing LE scan or not. The flag
is set/cleared when the controller starts/stops scanning.
This is an initial effort to stop using hdev->flags to define
internal flags since it is exported to userspace by an ioctl.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Upstream Code Aurora function with minor trivial fixes.
Origin: git://codeaurora.org/kernel/msm.git
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
In irq_wait_for_interrupt(), the should_stop member is verified before
setting the task's state to TASK_INTERRUPTIBLE and calling schedule().
In case kthread_stop sets should_stop and wakes up the process after
should_stop is checked by the irq thread but before the task's state
is changed, the irq thread might never exit:
kthread_stop irq_wait_for_interrupt
------------ ----------------------
...
... while (!kthread_should_stop()) {
kthread->should_stop = 1;
wake_up_process(k);
wait_for_completion(&kthread->exited);
...
set_current_state(TASK_INTERRUPTIBLE);
...
schedule();
}
Fix this by checking if the thread should stop after modifying the
task's state.
[ tglx: Simplified it a bit ]
Signed-off-by: Ido Yariv <ido@wizery.com>
Link: http://lkml.kernel.org/r/1322740508-22640-1-git-send-email-ido@wizery.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
|
|
There are two issues in vmw_kms_update_layout_ioctl(). First, the
for loop forgets to index rects and only checks the first element.
Second, there is a potential integer overflow if userspace passes
in a large arg->num_outputs. The call to kzalloc() would allocate
a small buffer, leading to out-of-bounds read.
Reported-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=43191
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
