| Age | Commit message (Collapse) | Author |
|---|
|
This is needed as a dependency for omap/ehci.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into omap/hwmod
|
|
This fixes the build of the macb driver that was broken by the DT changes:
drivers/net/ethernet/cadence/macb.c:1503: error: implicit declaration of function 'of_match_ptr'
drivers/net/ethernet/cadence/macb.c:1503: error: 'macb_dt_ids' undeclared here (not in a function)
drivers/net/ethernet/cadence/macb.c:1503: error: initializer element is not constant
drivers/net/ethernet/cadence/macb.c:1503: error: (near initialization for 'macb_driver.driver.of_match_table')
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
|
|
fixes-hwmod
|
|
|
|
Use the generic gpiolib gpio_is_valid() function to test
if the phy IRQ line GPIO is actually provided.
For non-connected or non-existing phy IRQ lines, -EINVAL
value is used for phy_irq_pin field of struct at91_eth_data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Add the Cadence macb ethernet controller in at91sam9g45 and at91sam9g20
.dtsi and enable it in at91sam9m10g45ek and usb_a9g20 board device tree file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Allow the device tree to provide the mac address and the phy mode.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change "compatible" node property, doc and DT hwaddr]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[jamie@jamieiles.com: add "gem" compatibility strings and doc]
Acked-by: Jamie Iles<jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
For I2C clockactivity field is added for OMAP3 and OMAP4 that defines how the
interface (OCP) and functional (system) clocks behave when the I2C module is
idle.
The configuration of the clock activity bit field (per TRM) is as follows:
0x0: Both clocks can be cut off
0x1: Only OCP clock must be kept active; system clock
can be cut off
0x3: Both clocks must be kept active
0x2: Only system clock must be kept active; OCP clock
can be cut off
The patch makes 0x2(CLOCKACT_TEST_ICLK) the default for OMAP3 and OMAP4.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
<= ES2.1
The HSMMC1/HSMMC2 host controllers on OMAP34xx and
OMAP3503/3515/3525/3530 chips at ES levels prior to 3.0 can't do multiple
block reads[1]. Mark the hwmod data appropriately.
Reported by Dave Hylands <dhylands@gmail.com> and Steve Sakoman
<sakoman@gmail.com>. Thanks to Steve Sakoman for further help
testing this patch.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
|
|
Following 2 hwmod structures are added
1. usb_host_hs
The hwmod of usbhs with uhh, ehci and ohci base addresses
functional clock and ehci, ohci irqs
2. usb_tll_hs
hwmod of usbhs with the TLL base address and irq.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[keshava_mgowda@ti.com: rebased to kernel version 3.0, added workarounds for
hardware issues]
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
[paul@pwsan.com: fixed multi-line comments, fixed whitespace, fixed S-o-b
notes, removed spurious TLL->L3 interface]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Following 2 hwmod structures are added
1. usb_host_hs
The hwmod of usbhs with uhh, ehci and ohci base addresses
functional clock and ehci, ohci irqs
2. usb_tll_hs
hwmod of usbhs with the TLL base address and irq.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
[paul@pwsan.com: fixed whitespace; removed nonexistent TLL->L3 interface;
added master & slave for L4 CORE->TLL interface; skip registration on
3430ES1; fixed multiline comment style; updated to apply on Tony's cleanup
branch; rebased]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add hwmod support to enable access to UART4 of the AM35xx series of
chips. The UART4 device referenced from the TRM will show up as ttyO3.
This was tested on an AM3505.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Booting the Linux kernel on Nokia RM-680 board has been broken since
2.6.39 due to the following:
[ 0.217193] omap_hwmod: timer12: enabling
[ 0.221435] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa304010
[ 0.229431] Internal error: : 1028 [#1] SMP
[ 0.233825] Modules linked in:
[ 0.237060] CPU: 0 Not tainted (3.2.0-rc4-dirty #46)
[ 0.242645] PC is at _update_sysc_cache+0x2c/0x7c
[ 0.247589] LR is at _enable+0x1b0/0x2d8
[ 0.251708] pc : [<c0026108>] lr : [<c0026df4>] psr: 40000013
[ 0.251708] sp : ef831f40 ip : ef82f380 fp : c06ac0c0
[ 0.263702] r10: 00000000 r9 : c05dfb2c r8 : ef830000
[ 0.269165] r7 : c0027494 r6 : 00000000 r5 : 00000000 r4 : c06608b0
[ 0.276000] r3 : fa304000 r2 : 00000010 r1 : c0661e28 r0 : c06608b0
[ 0.282806] Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 0.290405] Control: 10c5387d Table: 80004019 DAC: 00000017
[ 0.296417] Process swapper (pid: 1, stack limit = 0xef8302f8)
[ 0.302520] Stack: (0xef831f40 to 0xef832000)
[ 0.307098] 1f40: c06608b0 c0026df4 c06ad094 c0035120 00000001 c06608b0 00000000 c0027530
[ 0.315612] 1f60: c0027604 ef830000 c05dfb2c c06608b0 c0642ac0 c0025bf0 c0621234 c062120c
[ 0.324127] 1f80: c0621738 00000013 ef830000 c05dfb6c c0621234 c0008688 c062c880 c009eadc
[ 0.332641] 1fa0: 0000005f 00000000 c0621738 35390013 00000000 00000000 00000000 0000019a
[ 0.341156] 1fc0: c0681cf4 c0621234 c062120c c0621738 00000013 00000000 00000000 00000000
[ 0.349670] 1fe0: 00000000 c05d5298 00000000 c05d5200 c0014fa8 c0014fa8 ffff0000 ffff0000
[ 0.358184] [<c0026108>] (_update_sysc_cache+0x2c/0x7c) from [<c0026df4>] (_enable+0x1b0/0x2d8)
[ 0.367248] [<c0026df4>] (_enable+0x1b0/0x2d8) from [<c0027530>] (_setup+0x9c/0x170)
[ 0.375335] [<c0027530>] (_setup+0x9c/0x170) from [<c0025bf0>] (omap_hwmod_for_each+0x38/0x58)
[ 0.384307] [<c0025bf0>] (omap_hwmod_for_each+0x38/0x58) from [<c05dfb6c>] (omap_hwmod_setup_all+0x40/0xa0)
[ 0.394409] [<c05dfb6c>] (omap_hwmod_setup_all+0x40/0xa0) from [<c0008688>] (do_one_initcall+0x34/0x180)
[ 0.404296] [<c0008688>] (do_one_initcall+0x34/0x180) from [<c05d5298>] (kernel_init+0x98/0x144)
[ 0.413452] [<c05d5298>] (kernel_init+0x98/0x144) from [<c0014fa8>] (kernel_thread_exit+0x0/0x8)
[ 0.422576] Code: e3130c01 1590304c 0590304c 119320b2 (07932002)
[ 0.429046] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.433959] Kernel panic - not syncing: Attempted to kill init!
Timer 12 is not necessarily available on non-GP devices (see e.g.
http://marc.info/?l=linux-omap&m=129433066521102&w=2), so it should be
registered only on GP OMAPs. With this change it's again possible to
boot RM-680 into the shell. Tested with 3.2-rc4.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[paul@pwsan.com: changed subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Seems the commit 7e89098 was overly aggressive in adding iva and mailbox
hwmods so now they are registered twice.
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: iva: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1c ]---
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: mailbox: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1d ]---
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit 10299e2e4e3ed3b16503d4e04edd48b33083f4e2 (ARM: RX-51:
Enable isp1704 power on/off) added power management for isp1704.
However, the transceiver should be powered on by default,
otherwise USB doesn't work at all for networking during
boot.
All kernels after v3.0 are affected.
Cc: stable@kernel.org
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into omap/hsmmc
|
|
Commits 09d28d ("ARM: OMAP: mcbsp: Start generalize omap2_mcbsp_set_clks_src")
and 7bc0c4 ("ARM: OMAP: mcbsp: Start generalize signal muxing functions")
incorrectly set two struct omap_mcbsp_platform_data fields after
omap_device_build_ss and kfree calls.
Fix this by moving these pdata assignments before those calls.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
* git://git.samba.org/sfrench/cifs-2.6:
cifs: check for NULL last_entry before calling cifs_save_resume_key
cifs: attempt to freeze while looping on a receive attempt
cifs: Fix sparse warning when calling cifs_strtoUCS
CIFS: Add descriptions to the brlock cache functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Calling __pa() with an ioremap()ed address is invalid
x86, hpet: Immediately disable HPET timer 1 if rtc irq is masked
x86/intel_mid: Kconfig select fix
x86/intel_mid: Fix the Kconfig for MID selection
|
|
* 'spi/for-3.2' of git://git.pengutronix.de/git/wsa/linux-2.6:
spi/gpio: fix section mismatch warning
spi/fsl-espi: disable CONFIG_SPI_FSL_ESPI=m build
spi/nuc900: Include linux/module.h
spi/ath79: fix compile error due to missing include
|
|
Add support for base-board MMC slot
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following error message which appears
while intializing MMC1 on the AM3517 EVM base-board:
mmc0: host doesn't support card's voltages
mmc0: error -22 whilst initialising SD card
The ocr_mask, which enumerates the volatges supported by the
MMC card was not being indicated before, assuming that a separate
Vcc regulator maybe another controllable regulator driver would be
doing this. This patch statically specifies a subset of the voltages
supported by the MMC driver, which are provided by the current fixed
voltage regulator on AM3517 EVM.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Devkit8000 uses a TWL4030 pin for card detection.
Thats why the error:
_omap_mux_init_gpio: Could not set gpio192
occurs.
This patch checks that the pin is on OMAP before
calling omap_mux_init_gpio.
Signed-off-by: Thomas Weber <weber@corscience.de>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM35x MMC 2 controller has internal clock loopback setting which cannot
be utilized without this patch and thus SDIO devices connected to this
controller and depend on this setting will fail to initialize.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Declare support for keeping the power of the wlan chip
while suspended. this is needed for Wakeup-On-Wireless.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
* 'for-linus' of git://neil.brown.name/md:
md: raid5 crash during degradation
md/raid5: never wait for bad-block acks on failed device.
md: ensure new badblocks are handled promptly.
md: bad blocks shouldn't cause a Blocked status on a Faulty device.
md: take a reference to mddev during sysfs access.
md: refine interpretation of "hold_active == UNTIL_IOCTL".
md/lock: ensure updates to page_attrs are properly locked.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: use new generic {enable,disable}_percpu_irq() routines
drivers/net/ethernet/tile: use skb_frag_page() API
asm-generic/unistd.h: support new process_vm_{readv,write} syscalls
arch/tile: fix double-free bug in homecache_free_pages()
arch/tile: add a few #includes and an EXPORT to catch up with kernel changes.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
MAINTAINERS: Update amd-iommu F: patterns
iommu/amd: Fix typo in kernel-parameters.txt
iommu/msm: Fix compile error in mach-msm/devices-iommu.c
Fix comparison using wrong pointer variable in dma debug code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix lost speaker volume controls
ALSA: hda/realtek - Create "Bass Speaker" for two speaker pins
ALSA: hda/realtek - Don't create extra controls with channel suffix
ALSA: hda - Fix remaining VREF mute-LED NID check in post-3.1 changes
ALSA: hda - Fix GPIO LED setup for IDT 92HD75 codecs
ASoC: Provide a more complete DMA driver stub
ASoC: Remove references to corgi and spitz from machine driver document
ASoC: Make SND_SOC_MX27VIS_AIC32X4 depend on I2C
ASoC: Fix dependency for SND_SOC_RAUMFELD and SND_PXA2XX_SOC_HX4700
ASoC: uda1380: Return proper error in uda1380_modinit failure path
ASoC: kirkwood: Make SND_KIRKWOOD_SOC_OPENRD and SND_KIRKWOOD_SOC_T5325 depend on I2C
ASoC: Mark WM8994 ADC muxes as virtual
ALSA: hda/realtek - Fix Oops in alc_mux_select()
ALSA: sis7019 - give slow codecs more time to reset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Do no try to schedule task events if there are none
lockdep, kmemcheck: Annotate ->lock in lockdep_init_map()
perf header: Use event_name() to get an event name
perf stat: Failure with "Operation not supported"
|
|
In order to safely dereference current->real_parent inside an
rcu_read_lock, we need an rcu_dereference.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Modify initialization of PCIe capability registers in Tsi721 mport driver:
- change Completion Timeout value to avoid unexpected data transfer
aborts during intensive traffic.
- replace hardcoded offset of PCIe capability block by making it use the
common function.
This patch is applicable to kernel versions starting from 3.2-rc1.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bug fix for Tsi721 RapidIO mport driver: Tsi721 supports four RapidIO
mailboxes (MBOX0 - MBOX3) as defined by RapidIO specification. Mailbox
resources has to be properly reported to allow use of all available
mailboxes (initial version reports only MBOX0).
This patch is applicable to kernel versions staring from 3.2-rc1.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace the pair dma_alloc_coherent()+memset() with the new
dma_zalloc_coherent() added by Andrew Morton for kernel version 3.2
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit a25cac5198d4 ("proc: Consider NO_HZ when printing idle and
iowait times") we are reporting idle/io_wait time also while a CPU is
tickless. We rely on get_{idle,iowait}_time functions to retrieve
proper data.
These functions, however, use usecs_to_cputime to translate micro
seconds time to cputime64_t. This is just an alias to usecs_to_jiffies
which reduces the data type from u64 to unsigned int and also checks
whether the given parameter overflows jiffies_to_usecs(MAX_JIFFY_OFFSET)
and returns MAX_JIFFY_OFFSET in that case.
When we overflow depends on CONFIG_HZ but especially for CONFIG_HZ_300
it is quite low (1431649781) so we are getting MAX_JIFFY_OFFSET for
>3000s! until we overflow unsigned int. Just for reference
CONFIG_HZ_100 has an overflow window around 20s, CONFIG_HZ_250 ~8s and
CONFIG_HZ_1000 ~2s.
This results in a bug when people saw [h]top going mad reporting 100%
CPU usage even though there was basically no CPU load. The reason was
simply that /proc/stat stopped reporting idle/io_wait changes (and
reported MAX_JIFFY_OFFSET) and so the only change happening was for user
system time.
Let's use nsecs_to_jiffies64 instead which doesn't reduce the precision
to 32b type and it is much more appropriate for cumulative time values
(unlike usecs_to_jiffies which intended for timeout calculations).
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit f5252e00 ("mm: avoid null pointer access in vm_struct via
/proc/vmallocinfo") adds newly allocated vm_structs to the vmlist after
it is fully initialised. Unfortunately, it did not check that
__vmalloc_area_node() successfully populated the area. In the event of
allocation failure, the vmalloc area is freed but the pointer to freed
memory is inserted into the vmlist leading to a a crash later in
get_vmalloc_info().
This patch adds a check for ____vmalloc_area_node() failure within
__vmalloc_node_range. It does not use "goto fail" as in the previous
error path as a warning was already displayed by __vmalloc_area_node()
before it called vfree in its failure path.
Credit goes to Luciano Chavez for doing all the real work of identifying
exactly where the problem was.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Luciano Chavez <lnx1138@linux.vnet.ibm.com>
Tested-by: Luciano Chavez <lnx1138@linux.vnet.ibm.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org> [3.1.x+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
pageblocks
setup_zone_migrate_reserve() expects that zone->start_pfn starts at
pageblock_nr_pages aligned pfn otherwise we could access beyond an
existing memblock resulting in the following panic if
CONFIG_HOLES_IN_ZONE is not configured and we do not check pfn_valid:
IP: [<c02d331d>] setup_zone_migrate_reserve+0xcd/0x180
*pdpt = 0000000000000000 *pde = f000ff53f000ff53
Oops: 0000 [#1] SMP
Pid: 1, comm: swapper Not tainted 3.0.7-0.7-pae #1 VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform
EIP: 0060:[<c02d331d>] EFLAGS: 00010006 CPU: 0
EIP is at setup_zone_migrate_reserve+0xcd/0x180
EAX: 000c0000 EBX: f5801fc0 ECX: 000c0000 EDX: 00000000
ESI: 000c01fe EDI: 000c01fe EBP: 00140000 ESP: f2475f58
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 1, ti=f2474000 task=f2472cd0 task.ti=f2474000)
Call Trace:
[<c02d389c>] __setup_per_zone_wmarks+0xec/0x160
[<c02d3a1f>] setup_per_zone_wmarks+0xf/0x20
[<c08a771c>] init_per_zone_wmark_min+0x27/0x86
[<c020111b>] do_one_initcall+0x2b/0x160
[<c086639d>] kernel_init+0xbe/0x157
[<c05cae26>] kernel_thread_helper+0x6/0xd
Code: a5 39 f5 89 f7 0f 46 fd 39 cf 76 40 8b 03 f6 c4 08 74 32 eb 91 90 89 c8 c1 e8 0e 0f be 80 80 2f 86 c0 8b 14 85 60 2f 86 c0 89 c8 <2b> 82 b4 12 00 00 c1 e0 05 03 82 ac 12 00 00 8b 00 f6 c4 08 0f
EIP: [<c02d331d>] setup_zone_migrate_reserve+0xcd/0x180 SS:ESP 0068:f2475f58
CR2: 00000000000012b4
We crashed in pageblock_is_reserved() when accessing pfn 0xc0000 because
highstart_pfn = 0x36ffe.
The issue was introduced in 3.0-rc1 by 6d3163ce ("mm: check if any page
in a pageblock is reserved before marking it MIGRATE_RESERVE").
Make sure that start_pfn is always aligned to pageblock_nr_pages to
ensure that pfn_valid s always called at the start of each pageblock.
Architectures with holes in pageblocks will be correctly handled by
pfn_valid_within in pageblock_is_reserved.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Tested-by: Dang Bo <bdang@vmware.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Arve Hjnnevg <arve@android.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> [3.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Avoid unlocking and unlocked page if we failed to lock it.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 70b50f94f1644 ("mm: thp: tail page refcounting fix") keeps all
page_tail->_count zero at all times. But the current kernel does not
set page_tail->_count to zero if a 1GB page is utilized. So when an
IOMMU 1GB page is used by KVM, it wil result in a kernel oops because a
tail page's _count does not equal zero.
kernel BUG at include/linux/mm.h:386!
invalid opcode: 0000 [#1] SMP
Call Trace:
gup_pud_range+0xb8/0x19d
get_user_pages_fast+0xcb/0x192
? trace_hardirqs_off+0xd/0xf
hva_to_pfn+0x119/0x2f2
gfn_to_pfn_memslot+0x2c/0x2e
kvm_iommu_map_pages+0xfd/0x1c1
kvm_iommu_map_memslots+0x7c/0xbd
kvm_iommu_map_guest+0xaa/0xbf
kvm_vm_ioctl_assigned_device+0x2ef/0xa47
kvm_vm_ioctl+0x36c/0x3a2
do_vfs_ioctl+0x49e/0x4e4
sys_ioctl+0x5a/0x7c
system_call_fastpath+0x16/0x1b
RIP gup_huge_pud+0xf2/0x159
Signed-off-by: Youquan Song <youquan.song@intel.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the 3.2-rc kernel, IOMMU 2M pages in KVM works. But when I tried
to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page
failed to be used.
The root cause is that 1GB page allocation calls gup_huge_pud() while 2M
page calls gup_huge_pmd. If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that.
So when the mapped page is relesed, it will result in kernel oops
because the page is not marked mapped.
This patch add tail process for compound page in 1GB huge page which
keeps the same process as 2M page.
Reproduce like:
1. Add grub boot option: hugepagesz=1G hugepages=8
2. mount -t hugetlbfs -o pagesize=1G hugetlbfs /dev/hugepages
3. qemu-kvm -m 2048 -hda os-kvm.img -cpu kvm64 -smp 4 -mem-path /dev/hugepages
-net none -device pci-assign,host=07:00.1
kernel BUG at mm/swap.c:114!
invalid opcode: 0000 [#1] SMP
Call Trace:
put_page+0x15/0x37
kvm_release_pfn_clean+0x31/0x36
kvm_iommu_put_pages+0x94/0xb1
kvm_iommu_unmap_memslots+0x80/0xb6
kvm_assign_device+0xba/0x117
kvm_vm_ioctl_assigned_device+0x301/0xa47
kvm_vm_ioctl+0x36c/0x3a2
do_vfs_ioctl+0x49e/0x4e4
sys_ioctl+0x5a/0x7c
system_call_fastpath+0x16/0x1b
RIP put_compound_page+0xd4/0x168
Signed-off-by: Youquan Song <youquan.song@intel.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 4f2a8d3cf5e ("printk: Fix console_sem vs logbuf_lock unlock race")
introduced another silly bug where we would want to acquire an already
held lock. Avoid this.
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
More players joined to memory cgroup developments and Johannes' great work
changed internal design of memory cgroup dramatically. And he will do
more works. Michal Hokko did many bug fixes and know memory cgroup very
well. Daisuke Nishimura helped us very much but he seems busy now.
Thanks to his works.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If an error occurs after the clock is enabled, the enable/disable state
can become unbalanced.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Small clean-up for my CREDITS entry; the GPG fingerprint was not up to
date, so I fixed other details at the same time too.
Signed-off-by: Kees Cook <kees@outflux.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
khugepaged can sometimes cause suspend to fail, requiring that the user
retry the suspend operation.
Use wait_event_freezable_timeout() instead of
schedule_timeout_interruptible() to avoid missing freezer wakeups. A
try_to_freeze() would have been needed in the khugepaged_alloc_hugepage
tight loop too in case of the allocation failing repeatedly, and
wait_event_freezable_timeout will provide it too.
khugepaged would still freeze just fine by trying again the next minute
but it's better if it freezes immediately.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: "Rafael J. Wysocki" <rjw@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the error message "directives may not be used inside a macro argument"
which appears when the kernel is compiled for the cris architecture.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
