| Age | Commit message (Collapse) | Author |
|---|
|
commit df66834a43c461de2565c45d815288ba1c0def37 upstream.
The present code does not wait for the SCC to finish resetting itself
before trying to initialise the device. The result is that the SCC
interrupt sources become enabled (if they weren't already). This leads to
an early boot crash (unexpected interrupt) given CONFIG_EARLY_PRINTK. Fix
this by adding a delay. A successful reset disables the interrupt sources.
Also, after the reset for channel A setup, the SCC then gets a second
reset for channel B setup which leaves channel A uninitialised again. Fix
this by performing the reset only once.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e771451c0a831d96a7c14b0ca8a8ec671d98567b upstream.
libata honors DMADIR for regular commands, but not for internal commands
used (among other) during device initialisation.
This makes SATA-host-to-PATA-device bridges based on Silicon Image SiL3611
(such as "Abit Serillel 2") end up disabled when used with an ATAPI device
after a few tries.
Log output of the bridge being hot-plugged with an ATAPI drive:
[ 9631.212901] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
[ 9631.212913] ata1: irq_stat 0x00000040, connection status changed
[ 9631.212923] ata1: SError: { CommWake 10B8B DevExch }
[ 9631.212939] ata1: hard resetting link
[ 9632.104962] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9632.106393] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33
[ 9632.106407] ata1.00: applying bridge limits
[ 9632.108151] ata1.00: configured for UDMA/33
[ 9637.105303] ata1.00: qc timeout (cmd 0xa0)
[ 9637.105324] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
[ 9637.105335] ata1: hard resetting link
[ 9638.044599] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9638.047878] ata1.00: configured for UDMA/33
[ 9643.044933] ata1.00: qc timeout (cmd 0xa0)
[ 9643.044953] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
[ 9643.044963] ata1: limiting SATA link speed to 1.5 Gbps
[ 9643.044971] ata1.00: limiting speed to UDMA/33:PIO3
[ 9643.044979] ata1: hard resetting link
[ 9643.984225] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9643.987471] ata1.00: configured for UDMA/33
[ 9648.984591] ata1.00: qc timeout (cmd 0xa0)
[ 9648.984612] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
[ 9648.984619] ata1.00: disabled
[ 9649.000593] ata1: hard resetting link
[ 9649.939902] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9649.955864] ata1: EH complete
With this patch, the drive enumerates correctly when libata is loaded with
atapi_dmadir=1:
[ 9891.810863] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
[ 9891.810874] ata1: irq_stat 0x00000040, connection status changed
[ 9891.810884] ata1: SError: { CommWake 10B8B DevExch }
[ 9891.810900] ata1: hard resetting link
[ 9892.762105] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9892.763544] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33, DMADIR
[ 9892.763558] ata1.00: applying bridge limits
[ 9892.765393] ata1.00: configured for UDMA/33
[ 9892.786063] ata1: EH complete
[ 9892.792062] scsi 0:0:0:0: CD-ROM PIONEER DVD-RW DVR-115 1.06 PQ: 0 ANSI: 5
[ 9892.798455] sr2: scsi3-mmc drive: 12x/12x writer dvd-ram cd/rw xa/form2 cdda tray
[ 9892.798837] sr 0:0:0:0: Attached scsi CD-ROM sr2
[ 9892.799109] sr 0:0:0:0: Attached scsi generic sg6 type 5
Based on a patch by Csaba Halász <csaba.halasz@gmail.com> on linux-ide:
http://marc.info/?l=linux-ide&m=136121147832295&w=2
tj: minor formatting changes.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fca8c90d519dedd4f4b19901d005c243f7f0bf2e upstream.
Adds IDE-mode SATA Device IDs for the Intel BayTrail platform.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52a2a1087b5924de00484f35ef5e2a73f61dbd22 upstream.
The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.
Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear only those interrupts that we have read
as active first time around, because else we have a race and risk clearing an
interrupt that can occur between read and write of the SATAINTSTAT register
and never registering it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit df7e131f6359f20ed8f0a37db039c4f6420a18c2 upstream.
Iff bmdma_setup() has to stop a DMA transfer before starting a new
one, then the STOP bit in the ATAPI_CONTROL1 register will remain set
(it's only cleared when setting the START bit to 1) and then
bmdma_start() method will set both START and STOP bits simultaneously
which should abort the transfer being just started. Avoid that by
explicitly clearing the STOP bit in bmdma_start() method (in this case
it will be ignored on write).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 166faf21bd14bc5c5295a44874bf7f3930c30b20 upstream.
Consider the case where we have a very short ip= string in the original
mount options, and when we chase a referral we end up with a very long
IPv6 address. Be sure to allow for that possibility when estimating the
size of the string to allocate.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 286233e604d79f0c7fa04abec2180d5d89a74749 upstream.
req->assoc is dma mapped BIDIRECTIONAL and unmapped TO_DEVICE.
Since it is read-only for the device, use TO_DEVICE both for mapping
and unmapping.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09fb8bd1a63b0f9f15e655c4fe8d047e5d2bf67a upstream.
Newer asics have variable numbers of crtcs. Use that
rather than the asic family to determine which crtcs
to check. This avoids checking non-existent crtcs or
missing crtcs on certain asics.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 468ef1a58c9268ac9709350bf95eaf1c22a69f29 upstream.
Should be 5 rather than 2.
Noticed by sroland and glisse on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c98b4871cca4b7ce07e19f92f934d47cf7210b0 upstream.
At DDX commit Chris mentioned the tendency we have of finding out more
PCI IDs only when users report. So Let's add all new reserved Haswell IDs.
This patch also fix GT3 names. I'no not sending in separated patche because
names are only in few comments and not in variable names.
v2: Fix some mobile ids (by Paulo)
References: http://bugs.freedesktop.org/show_bug.cgi?id=63701
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 39d4ecdb711ba44e0aa0b2f3db74ed5ac97abe21 upstream.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04d245b7899c020559402841d2f70ddd740a7704 upstream.
The default register value for MASTERA_VOL is 0x00, the same as
MASTERB_VOL.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit afe3c3fd5392b2f0066930abc5dbd3f4b14a0f13 upstream.
As of f025adf191924e3a75ce80e130afcd2485b53bb8 "sunrpc: Properly decode
kuids and kgids in RPC_AUTH_UNIX credentials" any rpc containing a -1
(0xffff) uid or gid would fail with a badcred error.
Reported symptoms were xmbc clients failing on upgrade of the NFS
server; examination of the network trace showed them sending -1 as the
gid.
Reported-by: Julian Sikorski <belegdol@gmail.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3c3cac5d31879cd9ae2de7874dc6544ca704aec upstream.
The lockless RPC_IS_QUEUED() test in __rpc_execute means that we need to
be careful about ordering the calls to rpc_test_and_set_running(task) and
rpc_clear_queued(task). If we get the order wrong, then we may end up
testing the RPC_TASK_RUNNING flag after __rpc_execute() has looped
and changed the state of the rpc_task.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30da66eafc015cd7e952829eaf8f86d8680f86d9 upstream.
The s5p_csis_phy_enable/s5p_dsim_phy_enable functions are now used
directly by corresponding drivers and thus need to be exported so
the drivers can be built as modules.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9955ac47f4ba1c95ecb6092aeaefb40a22e99268 upstream.
Rather than completely killing the kernel if we receive an esr value we
can't deal with in the el0 handlers, send the process a SIGILL and log
the esr value in the hope that we can debug it. If we receive a bad esr
from el1, we'll die() as before.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2962f5a5dcc56f69cbf62121a7be67cc15d6940b upstream.
XFS has failed to kill suid/sgid bits correctly when truncating
files of non-zero size since commit c4ed4243 ("xfs: split
xfs_setattr") introduced in the 3.1 kernel. Fix it.
Fix it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 944a1fa01266aa9ace607f29551b73c41e9440e9 upstream.
Otherwise we get a race between unload and reload of the same module:
the new module doesn't see the old one in the list, but then fails because
it can't register over the still-extant entries in sysfs:
[ 103.981925] ------------[ cut here ]------------
[ 103.986902] WARNING: at fs/sysfs/dir.c:536 sysfs_add_one+0xab/0xd0()
[ 103.993606] Hardware name: CrownBay Platform
[ 103.998075] sysfs: cannot create duplicate filename '/module/pch_gbe'
[ 104.004784] Modules linked in: pch_gbe(+) [last unloaded: pch_gbe]
[ 104.011362] Pid: 3021, comm: modprobe Tainted: G W 3.9.0-rc5+ #5
[ 104.018662] Call Trace:
[ 104.021286] [<c103599d>] warn_slowpath_common+0x6d/0xa0
[ 104.026933] [<c1168c8b>] ? sysfs_add_one+0xab/0xd0
[ 104.031986] [<c1168c8b>] ? sysfs_add_one+0xab/0xd0
[ 104.037000] [<c1035a4e>] warn_slowpath_fmt+0x2e/0x30
[ 104.042188] [<c1168c8b>] sysfs_add_one+0xab/0xd0
[ 104.046982] [<c1168dbe>] create_dir+0x5e/0xa0
[ 104.051633] [<c1168e78>] sysfs_create_dir+0x78/0xd0
[ 104.056774] [<c1262bc3>] kobject_add_internal+0x83/0x1f0
[ 104.062351] [<c126daf6>] ? kvasprintf+0x46/0x60
[ 104.067231] [<c1262ebd>] kobject_add_varg+0x2d/0x50
[ 104.072450] [<c1262f07>] kobject_init_and_add+0x27/0x30
[ 104.078075] [<c1089240>] mod_sysfs_setup+0x80/0x540
[ 104.083207] [<c1260851>] ? module_bug_finalize+0x51/0xc0
[ 104.088720] [<c108ab29>] load_module+0x1429/0x18b0
We can teardown sysfs first, then to be sure, put the state in
MODULE_STATE_UNFORMED so it's ignored while we deconstruct it.
Reported-by: Veaceslav Falico <vfalico@redhat.com>
Tested-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2baad6121e2b2fa3428ee6cb2298107be11ab23a upstream.
binutils prior to 2.18 (e.g. the ones found on SLE10) don't support
assembling PEXTRD, so a macro based approach like the one for PCLMULQDQ
in the same file should be used.
This requires making the helper macros capable of recognizing 32-bit
general purpose register operands.
[ hpa: tagging for stable as it is a low risk build fix ]
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/51A6142A02000078000D99D8@nat28.tlf.novell.com
Cc: Alexander Boyko <alexander_boyko@xyratex.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fbe06b7bae7c9cf6ab05168fce5ee93b2f4bae7c upstream.
Christian found v3.9 does not work with E350 with EFI is enabled.
[ 1.658832] Trying to unpack rootfs image as initramfs...
[ 1.679935] BUG: unable to handle kernel paging request at ffff88006e3fd000
[ 1.686940] IP: [<ffffffff813661df>] memset+0x1f/0xb0
[ 1.692010] PGD 1f77067 PUD 1f7a067 PMD 61420067 PTE 0
but early memtest report all memory could be accessed without problem.
early page table is set in following sequence:
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] init_memory_mapping: [mem 0x6e600000-0x6e7fffff]
[ 0.000000] init_memory_mapping: [mem 0x6c000000-0x6e5fffff]
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x6bffffff]
[ 0.000000] init_memory_mapping: [mem 0x6e800000-0x6ea07fff]
but later efi_enter_virtual_mode try set mapping again wrongly.
[ 0.010644] pid_max: default: 32768 minimum: 301
[ 0.015302] init_memory_mapping: [mem 0x640c5000-0x6e3fcfff]
that means it fails with pfn_range_is_mapped.
It turns out that we have a bug in add_range_with_merge and it does not
merge range properly when new add one fill the hole between two exsiting
ranges. In the case when [mem 0x00100000-0x6bffffff] is the hole between
[mem 0x00000000-0x000fffff] and [mem 0x6c000000-0x6e7fffff].
Fix the add_range_with_merge by calling itself recursively.
Reported-by: "Christian König" <christian.koenig@amd.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQVofGoSk7q5-0irjkBxemqK729cND4hov-1QCBJDhxpgQ@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9d0626ed43a41a3fc526d1df06122b0d4eac174 upstream.
In head_64.S, a switchover has been used to handle kernel crossing
1G, 512G boundaries.
And commit 8170e6bed465b4b0c7687f93e9948aca4358a33b
x86, 64bit: Use a #PF handler to materialize early mappings on demand
said:
During the switchover in head_64.S, before #PF handler is available,
we use three pages to handle kernel crossing 1G, 512G boundaries with
sharing page by playing games with page aliasing: the same page is
mapped twice in the higher-level tables with appropriate wraparound.
But from the switchover code, when we set up the PUD table:
114 addq $4096, %rdx
115 movq %rdi, %rax
116 shrq $PUD_SHIFT, %rax
117 andl $(PTRS_PER_PUD-1), %eax
118 movq %rdx, (4096+0)(%rbx,%rax,8)
119 movq %rdx, (4096+8)(%rbx,%rax,8)
It seems line 119 has a potential bug there. For example,
if the kernel is loaded at physical address 511G+1008M, that is
000000000 111111111 111111000 000000000000000000000
and the kernel _end is 512G+2M, that is
000000001 000000000 000000001 000000000000000000000
So in this example, when using the 2nd page to setup PUD (line 114~119),
rax is 511.
In line 118, we put rdx which is the address of the PMD page (the 3rd page)
into entry 511 of the PUD table. But in line 119, the entry we calculate from
(4096+8)(%rbx,%rax,8) has exceeded the PUD page. IMO, the entry in line
119 should be wraparound into entry 0 of the PUD table.
The patch fixes the bug.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/5191DE5A.3020302@cn.fujitsu.com
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5187b28ff08249ab8a162e802209ed04e271ca02 upstream.
With the addition of eagerfpu the irq_fpu_usable() now returns false
negatives especially in the case of ksoftirqd and interrupted idle task,
two common cases for FPU use for example in networking/crypto. With
eagerfpu=off FPU use is possible in those contexts. This is because of
the eagerfpu check in interrupted_kernel_fpu_idle():
...
* For now, with eagerfpu we will return interrupted kernel FPU
* state as not-idle. TBD: Ideally we can change the return value
* to something like __thread_has_fpu(current). But we need to
* be careful of doing __thread_clear_has_fpu() before saving
* the FPU etc for supporting nested uses etc. For now, take
* the simple route!
...
if (use_eager_fpu())
return 0;
As eagerfpu is automatically "on" on those CPUs that also have the
features like AES-NI this patch changes the eagerfpu check to return 1 in
case the kernel_fpu_begin() has not been said yet. Once it has been the
__thread_has_fpu() will start returning 0.
Notice that with eagerfpu the __thread_has_fpu is always true initially.
FPU use is thus always possible no matter what task is under us, unless
the state has already been saved with kernel_fpu_begin().
[ hpa: this is a performance regression, not a correctness regression,
but since it can be quite serious on CPUs which need encryption at
interrupt time I am marking this for urgent/stable. ]
Signed-off-by: Pekka Riikonen <priikone@iki.fi>
Link: http://lkml.kernel.org/r/alpine.GSO.2.00.1305131356320.18@git.silcnet.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96b04db9f2c16e77c31ef0e17e143da1e0cbfd78 upstream.
Add reset adapter after the 6th EEH errors in ipr driver. This triggers
the adapter reset via the PCI config space even when the slot is frozen.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7c3425123ddfdc5f48e7913ff59d908789712b18 upstream.
We should not use set_pmd_at to update pmd_t with pgtable_t pointer.
set_pmd_at is used to set pmd with huge pte entries and architectures
like ppc64, clear few flags from the pte when saving a new entry.
Without this change we observe bad pte errors like below on ppc64 with
THP enabled.
BUG: Bad page map in process ld mm=0xc000001ee39f4780 pte:7fc3f37848000001 pmd:c000001ec0000000
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9ff785e4437c83d2179161e012f5bdfbd6381f0 upstream.
A panic can be caused by simply cat'ing /proc/<pid>/smaps while an
application has a VM_PFNMAP range. It happened in-house when a
benchmarker was trying to decipher the memory layout of his program.
/proc/<pid>/smaps and similar walks through a user page table should not
be looking at VM_PFNMAP areas.
Certain tests in walk_page_range() (specifically split_huge_page_pmd())
assume that all the mapped PFN's are backed with page structures. And
this is not usually true for VM_PFNMAP areas. This can result in panics
on kernel page faults when attempting to address those page structures.
There are a half dozen callers of walk_page_range() that walk through a
task's entire page table (as N. Horiguchi pointed out). So rather than
change all of them, this patch changes just walk_page_range() to ignore
VM_PFNMAP areas.
The logic of hugetlb_vma() is moved back into walk_page_range(), as we
want to test any vma in the range.
VM_PFNMAP areas are used by:
- graphics memory manager gpu/drm/drm_gem.c
- global reference unit sgi-gru/grufile.c
- sgi special memory char/mspec.c
- and probably several out-of-tree modules
[akpm@linux-foundation.org: remove now-unused hugetlb_vma() stub]
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David Sterba <dsterba@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dfd20b2b174d3a9b258ea3b7a35ead33576587b1 upstream.
The index on the page must be set before it is inserted in the radix
tree. Otherwise there is a small race which can occur during lookup
where the page can be found with the incorrect index. This will trigger
the BUG_ON() in brd_lookup_page().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Chris Wedgwood <cw@f00f.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28ccddf7952c496df2a51ce5aee4f2a058a98bab upstream.
Commit 0c59b89c81ea ("mm: memcg: push down PageSwapCache check into
uncharge entry functions") added a VM_BUG_ON() on PageSwapCache in the
uncharge path after checking that page flag once, assuming that the
state is stable in all paths, but this is not the case and the condition
triggers in user environments. An uncharge after the last page table
reference to the page goes away can race with reclaim adding the page to
swap cache.
Swap cache pages are usually uncharged when they are freed after
swapout, from a path that also handles swap usage accounting and memcg
lifetime management. However, since the last page table reference is
gone and thus no references to the swap slot left, the swap slot will be
freed shortly when reclaim attempts to write the page to disk. The
whole swap accounting is not even necessary.
So while the race condition for which this VM_BUG_ON was added is real
and actually existed all along, there are no negative effects. Remove
the VM_BUG_ON again.
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d34883d4e35c0a994e91dd847a82b4c9e0c31d83 upstream.
Commit 751efd8610d3 ("mmu_notifier_unregister NULL Pointer deref and
multiple ->release()") breaks the fix 3ad3d901bbcf ("mm: mmu_notifier:
fix freed page still mapped in secondary MMU").
Since hlist_for_each_entry_rcu() is changed now, we can not revert that
patch directly, so this patch reverts the commit and simply fix the bug
spotted by that patch
This bug spotted by commit 751efd8610d3 is:
There is a race condition between mmu_notifier_unregister() and
__mmu_notifier_release().
Assume two tasks, one calling mmu_notifier_unregister() as a result
of a filp_close() ->flush() callout (task A), and the other calling
mmu_notifier_release() from an mmput() (task B).
A B
t1 srcu_read_lock()
t2 if (!hlist_unhashed())
t3 srcu_read_unlock()
t4 srcu_read_lock()
t5 hlist_del_init_rcu()
t6 synchronize_srcu()
t7 srcu_read_unlock()
t8 hlist_del_rcu() <--- NULL pointer deref.
This can be fixed by using hlist_del_init_rcu instead of hlist_del_rcu.
The another issue spotted in the commit is "multiple ->release()
callouts", we needn't care it too much because it is really rare (e.g,
can not happen on kvm since mmu-notify is unregistered after
exit_mmap()) and the later call of multiple ->release should be fast
since all the pages have already been released by the first call.
Anyway, this issue should be fixed in a separate patch.
-stable suggestions: Any version that has commit 751efd8610d3 need to be
backported. I find the oldest version has this commit is 3.0-stable.
[akpm@linux-foundation.org: tweak comments]
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Tested-by: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 136e8770cd5d1fe38b3c613100dd6dc4db6d4fa6 upstream.
nilfs2: fix issue of nilfs_set_page_dirty for page at EOF boundary
DESCRIPTION:
There are use-cases when NILFS2 file system (formatted with block size
lesser than 4 KB) can be remounted in RO mode because of encountering of
"broken bmap" issue.
The issue was reported by Anthony Doggett <Anthony2486@interfaces.org.uk>:
"The machine I've been trialling nilfs on is running Debian Testing,
Linux version 3.2.0-4-686-pae (debian-kernel@lists.debian.org) (gcc
version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.35-2), but I've
also reproduced it (identically) with Debian Unstable amd64 and Debian
Experimental (using the 3.8-trunk kernel). The problematic partitions
were formatted with "mkfs.nilfs2 -b 1024 -B 8192"."
SYMPTOMS:
(1) System log contains error messages likewise:
[63102.496756] nilfs_direct_assign: invalid pointer: 0
[63102.496786] NILFS error (device dm-17): nilfs_bmap_assign: broken bmap (inode number=28)
[63102.496798]
[63102.524403] Remounting filesystem read-only
(2) The NILFS2 file system is remounted in RO mode.
REPRODUSING PATH:
(1) Create volume group with name "unencrypted" by means of vgcreate utility.
(2) Run script (prepared by Anthony Doggett <Anthony2486@interfaces.org.uk>):
----------------[BEGIN SCRIPT]--------------------
VG=unencrypted
lvcreate --size 2G --name ntest $VG
mkfs.nilfs2 -b 1024 -B 8192 /dev/mapper/$VG-ntest
mkdir /var/tmp/n
mkdir /var/tmp/n/ntest
mount /dev/mapper/$VG-ntest /var/tmp/n/ntest
mkdir /var/tmp/n/ntest/thedir
cd /var/tmp/n/ntest/thedir
sleep 2
date
darcs init
sleep 2
dmesg|tail -n 5
date
darcs whatsnew || true
date
sleep 2
dmesg|tail -n 5
----------------[END SCRIPT]--------------------
REPRODUCIBILITY: 100%
INVESTIGATION:
As it was discovered, the issue takes place during segment
construction after executing such sequence of user-space operations:
open("_darcs/index", O_RDWR|O_CREAT|O_NOCTTY, 0666) = 7
fstat(7, {st_mode=S_IFREG|0644, st_size=0, ...}) = 0
ftruncate(7, 60)
The error message "NILFS error (device dm-17): nilfs_bmap_assign: broken
bmap (inode number=28)" takes place because of trying to get block
number for third block of the file with logical offset #3072 bytes. As
it is possible to see from above output, the file has 60 bytes of the
whole size. So, it is enough one block (1 KB in size) allocation for
the whole file. Trying to operate with several blocks instead of one
takes place because of discovering several dirty buffers for this file
in nilfs_segctor_scan_file() method.
The root cause of this issue is in nilfs_set_page_dirty function which
is called just before writing to an mmapped page.
When nilfs_page_mkwrite function handles a page at EOF boundary, it
fills hole blocks only inside EOF through __block_page_mkwrite().
The __block_page_mkwrite() function calls set_page_dirty() after filling
hole blocks, thus nilfs_set_page_dirty function (=
a_ops->set_page_dirty) is called. However, the current implementation
of nilfs_set_page_dirty() wrongly marks all buffers dirty even for page
at EOF boundary.
As a result, buffers outside EOF are inconsistently marked dirty and
queued for write even though they are not mapped with nilfs_get_block
function.
FIX:
This modifies nilfs_set_page_dirty() not to mark hole blocks dirty.
Thanks to Vyacheslav Dubeyko for his effort on analysis and proposals
for this issue.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Reported-by: Anthony Doggett <Anthony2486@interfaces.org.uk>
Reported-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4c663cfc523a88d97a8309b04a089c27dc57fd7e upstream.
Many callers of the wait_event_timeout() and
wait_event_interruptible_timeout() expect that the return value will be
positive if the specified condition becomes true before the timeout
elapses. However, at the moment this isn't guaranteed. If the wake-up
handler is delayed enough, the time remaining until timeout will be
calculated as 0 - and passed back as a return value - even if the
condition became true before the timeout has passed.
Fix this by returning at least 1 if the condition becomes true. This
semantic is in line with what wait_for_condition_timeout() does; see
commit bb10ed09 ("sched: fix wait_for_completion_timeout() spurious
failure under heavy load").
Daniel said "We have 3 instances of this bug in drm/i915. One case even
where we switch between the interruptible and not interruptible
wait_event_timeout variants, foolishly presuming they have the same
semantics. I very much like this."
One such bug is reported at
https://bugs.freedesktop.org/show_bug.cgi?id=64133
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac5a2962b02f57dea76d314ef2521a2170b28ab6 upstream.
There is a race between klist_remove and klist_release. klist_remove
uses a local var waiter saved on stack. When klist_release calls
wake_up_process(waiter->process) to wake up the waiter, waiter might run
immediately and reuse the stack. Then, klist_release calls
list_del(&waiter->list) to change previous
wait data and cause prior waiter thread corrupt.
The patch fixes it against kernel 3.9.
Signed-off-by: wang, biao <biao.wang@intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2cc499c5bcf9040a738f49e8051b42078205748 upstream.
Page 'new' during MIGRATION can't be flushed with flush_cache_page().
Using flush_cache_page(vma, addr, pfn) is justified only if the page is
already placed in process page table, and that is done right after
flush_cache_page(). But without it the arch function has no knowledge
of process PTE and does nothing.
Besides that, flush_cache_page() flushes an application cache page, but
the kernel has a different page virtual address and dirtied it.
Replace it with flush_dcache_page(new) which is the proper usage.
The old page is flushed in try_to_unmap_one() before migration.
This bug takes place in Sead3 board with M14Kc MIPS CPU without cache
aliasing (but Harvard arch - separate I and D cache) in tight memory
environment (128MB) each 1-3days on SOAK test. It fails in cc1 during
kernel build (SIGILL, SIGBUS, SIGSEG) if CONFIG_COMPACTION is switched
ON.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Leonid Yegoshin <yegoshin@mips.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ccc819da6fda9bee10ab8b72e9adbb5ad3e4959 upstream.
Fix bug in MSI interrupt handling which causes loss of event
notifications.
Typical indication of lost MSI interrupts are stalled message and
doorbell transfers between RapidIO endpoints. To avoid loss of MSI
interrupts all interrupts from the device must be disabled on entering
the interrupt handler routine and re-enabled when exiting it.
Re-enabling device interrupts will trigger new MSI message(s) if Tsi721
registered new events since entering interrupt handler routine.
This patch is applicable to kernel versions starting from v3.2.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b949b8af12e24b8a48fa5bb775a13b558d9f4da upstream.
During the development of this driver an in-house register documentation
was used. The last week some integration tests were done and this
problem was found. It turned out that the released register
documentation is wrong.
The fix is very simple: shift all masks by one.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99e11334dcb846f9b76fb808196c7f47aa83abb3 upstream.
Enable KW_PCIE1 on QNAP TS-11x/TS-21x devices as newer revisions
(rev 1.3) have a USB 3.0 chip from Etron on PCIe port 1. Thanks
to Marek Vasut for identifying this issue!
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b4ca2b4b577c3530e34dcfaafccb2cc680ce95d1 upstream.
Last time we found there is lock/unlock bug in ocfs2_file_aio_write, and
then we did a thorough search for all lock resources in
ocfs2_inode_info, including rw, inode and open lockres and found this
bug. My kernel version is 3.0.13, and it is also in the lastest version
3.9. In ocfs2_fiemap, once ocfs2_get_clusters_nocache failed, it should
goto out_unlock instead of out, because we need release buffer head, up
read alloc sem and unlock inode.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e99c60b58b595eaa1c279922ae29d5397c787294 upstream.
Manual peak calibration is currently enabled only for
AR9462 and AR9565. This is also required for AR9485.
The initvals are also modified to disable HW peak calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af690092ce91a2a6d807cdfcc0b0b9b71ae54d3e upstream.
Make sure that any open relayfs files are closed before
unregistering with mac80211, otherwise this crash is seen:
[ 1331.097846] BUG: unable to handle kernel paging request at 6b6b6b8b
[ 1331.098170] IP: [<c063d0d6>] debugfs_remove+0x26/0x80
[ 1331.098170] *pdpt = 000000002f9aa001 *pde = 0000000000000000
[ 1331.098170] Oops: 0000 [#1] PREEMPT SMP
[ 1331.098170] Modules linked in: iptable_raw xt_CT nf_conntrack_ipv4 nf_defrag]
[ 1331.098170] Pid: 4794, comm: rmmod Tainted: G WC 3.9.1+ #5 To Be Fi.
[ 1331.098170] EIP: 0060:[<c063d0d6>] EFLAGS: 00010202 CPU: 0
[ 1331.098170] EIP is at debugfs_remove+0x26/0x80
[ 1331.098170] EAX: f2f3acd0 EBX: f2f3acd0 ECX: 00000006 EDX: f8622348
[ 1331.098170] ESI: 6b6b6b6b EDI: 00000001 EBP: ee251e14 ESP: ee251e0c
[ 1331.098170] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 1331.098170] CR0: 8005003b CR2: 6b6b6b8b CR3: 2e7b7000 CR4: 000007e0
[ 1331.098170] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 1331.098170] DR6: ffff0ff0 DR7: 00000400
[ 1331.098170] Process rmmod (pid: 4794, ti=ee250000 task=efaa2560 task.ti=ee25)
[ 1331.098170] Stack:
[ 1331.098170] f241e170 0000000a ee251e1c f861394d ee251e28 c04e3088 f241e170 4
[ 1331.098170] c04e30fe f45482b0 ee251e54 c04e3187 f25e86b0 ee251e54 f8618748 0
[ 1331.098170] 0000000a 00000001 ee251e68 f860065b f2509e20 f25085a0 f5b6e8a4 8
[ 1331.098170] Call Trace:
[ 1331.098170] [<f861394d>] remove_buf_file_handler+0xd/0x20 [ath9k]
[ 1331.098170] [<c04e3088>] relay_remove_buf+0x18/0x30
[ 1331.098170] [<c04e30fe>] relay_close_buf+0x2e/0x40
[ 1331.098170] [<c04e3187>] relay_close+0x77/0xf0
[ 1331.098170] [<f8618748>] ? dpd_exit+0x38/0x40 [ath9k]
[ 1331.098170] [<f860065b>] ath9k_deinit_softc+0x8b/0xa0 [ath9k]
[ 1331.098170] [<f86006b8>] ath9k_deinit_device+0x48/0x60 [ath9k]
[ 1331.098170] [<f86107f1>] ath_pci_remove+0x31/0x50 [ath9k]
[ 1331.098170] [<c06dbff8>] pci_device_remove+0x38/0xc0
[ 1331.098170] [<c079daa4>] __device_release_driver+0x64/0xc0
[ 1331.098170] [<c079db97>] driver_detach+0x97/0xa0
[ 1331.098170] [<c079cacc>] bus_remove_driver+0x6c/0xe0
[ 1331.098170] [<c079c197>] ? bus_put+0x17/0x20
[ 1331.098170] [<c079cae3>] ? bus_remove_driver+0x83/0xe0
[ 1331.098170] [<c079e709>] driver_unregister+0x49/0x80
[ 1331.098170] [<c06dc138>] pci_unregister_driver+0x18/0x80
[ 1331.098170] [<f8610602>] ath_pci_exit+0x12/0x20 [ath9k]
[ 1331.098170] [<f8619ce0>] ath9k_exit+0x17/0x337 [ath9k]
[ 1331.098170] [<c09e537d>] ? mutex_unlock+0xd/0x10
[ 1331.098170] [<c04bd36c>] sys_delete_module+0x17c/0x250
[ 1331.098170] [<c0540dc4>] ? do_munmap+0x244/0x2d0
[ 1331.098170] [<c0540e96>] ? vm_munmap+0x46/0x60
[ 1331.098170] [<c09e8dc4>] ? restore_all+0xf/0xf
[ 1331.098170] [<c09ebf50>] ? __do_page_fault+0x4c0/0x4c0
[ 1331.098170] [<c04b18e4>] ? trace_hardirqs_on_caller+0xf4/0x180
[ 1331.098170] [<c09ef28d>] sysenter_do_call+0x12/0x38
[ 1331.098170] Code: 90 8d 74 26 00 55 89 e5 83 ec 08 89 1c 24 89 74 24 04 3e 82
[ 1331.098170] EIP: [<c063d0d6>] debugfs_remove+0x26/0x80 SS:ESP 0068:ee251e0c
[ 1331.098170] CR2: 000000006b6b6b8b
[ 1331.727971] ---[ end trace b5bb9f2066cef7f9 ]---
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a1e99dd2028e00998d42029be86835d8ef4a46e upstream.
The comparison between traced and symbol addresses is backwards: if
the traced address doesn't exactly match a symbol (which we don't
expect it to), we'll show the next symbol and the offset to it,
whereas we should show the previous symbol and the offset from it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 140c3c6a2bcd2c31e2f7f5a8d59689724776c8e5 upstream.
This works much better if we don't treat protocol numbers as addresses.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0f0d15100a8ac875bdd408324c473e16d73d3557 upstream.
The 5725 family of devices (asic rev 5762), corrupts TSO packets where
the buffer is within MSS bytes of a 4G boundary (4G, 8G etc.). Detect
this condition and trigger the workaround path.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44f3b503c16425c8e9db4bbaa2fc9cd0c9d0ba91 upstream.
On the 5718, 5719 and 5720 serdes devices, powering down function 0
results in all the other ports being powered down. Add code to skip
function 0 power down.
v2:
- Modify tg3_phy_power_bug() function to use a switch instead of a
complicated if statement. Suggested by Joe Perches.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b92d03c3239f43e5b86c9cc9630f026d36ee995 upstream.
Intermediate value of fat_clusters can be overflowed on 32bits arch.
Reported-by: Krzysztof Strasburger <strasbur@chkw386.ch.pwr.wroc.pl>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 10b3a32d292c21ea5b3ad5ca5975e88bb20b8d68 upstream.
Commit 902c098a3663 ("random: use lockless techniques in the interrupt
path") turned IRQ path from being spinlock protected into lockless
cmpxchg-retry update.
That commit removed r->lock serialization between crediting entropy bits
from IRQ context and accounting when extracting entropy on userspace
read path, but didn't turn the r->entropy_count reads/updates in
account() to use cmpxchg as well.
It has been observed, that under certain circumstances this leads to
read() on /dev/urandom to return 0 (EOF), as r->entropy_count gets
corrupted and becomes negative, which in turn results in propagating 0
all the way from account() to the actual read() call.
Convert the accounting code to be the proper lockless counterpart of
what has been partially done by 902c098a3663.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e7e2e05c179a68aaf8830fe91547a87f4589e53 upstream.
Commit ec8f02da9ea5 ("random: prime last_data value per fips
requirements") added priming of last_data per fips requirements.
Unfortuantely, it did so in a way that can lead to multiple threads all
incrementing nbytes, but only one actually doing anything with the extra
data, which leads to some fun random corruption and panics.
The fix is to simply do everything needed to prime last_data in a single
shot, so there's no window for multiple cpus to increment nbytes -- in
fact, we won't even increment or decrement nbytes anymore, we'll just
extract the needed EXTRACT_SIZE one time per pool and then carry on with
the normal routine.
All these changes have been tested across multiple hosts and
architectures w |
