| Age | Commit message (Collapse) | Author |
|---|
|
commit 991155bacb91c988c45586525771758ddadd44ce upstream.
This reverts commit e763eb699be723fb41af818118068c6b3afdaf8d.
Current IPsec ESN implementation for authencesn(cbc(aes), hmac(sha))
(separate encryption and integrity algorithms) does not conform
to RFC4303.
ICV is generated by hashing the sequence
SPI, SeqNum-High, SeqNum-Low, IV, Payload
instead of
SPI, SeqNum-Low, IV, Payload, SeqNum-High.
Reported-by: Chaoxing Lin <Chaoxing.Lin@ultra-3eti.com>
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4317ce877a31dbb9d96375391c1c4ad2210d637 upstream.
For the s626 driver, there is a bug in the handling of asynchronous
commands on the AI subdevice when the stop source is `TRIG_NONE`. The
command should run continuously until cancelled, but the interrupt
handler stops the command running after the first scan.
The command set-up function `s626_ai_cmd()` contains this code:
switch (cmd->stop_src) {
case TRIG_COUNT:
/* data arrives as one packet */
devpriv->ai_sample_count = cmd->stop_arg;
devpriv->ai_continous = 0;
break;
case TRIG_NONE:
/* continous acquisition */
devpriv->ai_continous = 1;
devpriv->ai_sample_count = 0;
break;
}
The interrupt handler `s626_irq_handler()` contains this code:
if (!(devpriv->ai_continous))
devpriv->ai_sample_count--;
if (devpriv->ai_sample_count <= 0) {
devpriv->ai_cmd_running = 0;
/* ... */
}
So `devpriv->ai_sample_count` is only decremented for the `TRIG_COUNT`
case, but `devpriv->ai_cmd_running` is set to 0 (and the command
stopped) regardless.
Fix this in `s626_ai_cmd()` by setting `devpriv->ai_sample_count = 1`
for the `TRIG_NONE` case. The interrupt handler will not decrement it
so it will remain greater than 0 and the check for stopping the
acquisition will fail.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ebaf5795ef57a70a042ea259448a465024e2821d upstream.
Add support for the AR9462 chip
T: Bus=03 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=817a Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d66629c1325399cf080ba8b2fb086c10e5439cdd upstream.
Add support for the AR9462 chip
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=0036 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb20ff9c91ddcb2d55c1849a87d3db85af5e88a9 upstream.
With deferred setup for SCO, it is possible that userspace closes the
socket when it is in the BT_CONNECT2 state, after the Connect Request is
received but before the Accept Synchonous Connection is sent.
If this happens the following crash was observed, when the connection is
terminated:
[ +0.000003] hci_sync_conn_complete_evt: hci0 status 0x10
[ +0.000005] sco_connect_cfm: hcon ffff88003d1bd800 bdaddr 40:98:4e:32:d7:39 status 16
[ +0.000003] sco_conn_del: hcon ffff88003d1bd800 conn ffff88003cc8e300, err 110
[ +0.000015] BUG: unable to handle kernel NULL pointer dereference at 0000000000000199
[ +0.000906] IP: [<ffffffff810620dd>] __lock_acquire+0xed/0xe82
[ +0.000000] PGD 3d21f067 PUD 3d291067 PMD 0
[ +0.000000] Oops: 0002 [#1] SMP
[ +0.000000] Modules linked in: rfcomm bnep btusb bluetooth
[ +0.000000] CPU 0
[ +0.000000] Pid: 1481, comm: kworker/u:2H Not tainted 3.9.0-rc1-25019-gad82cdd #1 Bochs Bochs
[ +0.000000] RIP: 0010:[<ffffffff810620dd>] [<ffffffff810620dd>] __lock_acquire+0xed/0xe82
[ +0.000000] RSP: 0018:ffff88003c3c19d8 EFLAGS: 00010002
[ +0.000000] RAX: 0000000000000001 RBX: 0000000000000246 RCX: 0000000000000000
[ +0.000000] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88003d1be868
[ +0.000000] RBP: ffff88003c3c1a98 R08: 0000000000000002 R09: 0000000000000000
[ +0.000000] R10: ffff88003d1be868 R11: ffff88003e20b000 R12: 0000000000000002
[ +0.000000] R13: ffff88003aaa8000 R14: 000000000000006e R15: ffff88003d1be850
[ +0.000000] FS: 0000000000000000(0000) GS:ffff88003e200000(0000) knlGS:0000000000000000
[ +0.000000] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ +0.000000] CR2: 0000000000000199 CR3: 000000003c1cb000 CR4: 00000000000006b0
[ +0.000000] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ +0.000000] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ +0.000000] Process kworker/u:2H (pid: 1481, threadinfo ffff88003c3c0000, task ffff88003aaa8000)
[ +0.000000] Stack:
[ +0.000000] ffffffff81b16342 0000000000000000 0000000000000000 ffff88003d1be868
[ +0.000000] ffffffff00000000 00018c0c7863e367 000000003c3c1a28 ffffffff8101efbd
[ +0.000000] 0000000000000000 ffff88003e3d2400 ffff88003c3c1a38 ffffffff81007c7a
[ +0.000000] Call Trace:
[ +0.000000] [<ffffffff8101efbd>] ? kvm_clock_read+0x34/0x3b
[ +0.000000] [<ffffffff81007c7a>] ? paravirt_sched_clock+0x9/0xd
[ +0.000000] [<ffffffff81007fd4>] ? sched_clock+0x9/0xb
[ +0.000000] [<ffffffff8104fd7a>] ? sched_clock_local+0x12/0x75
[ +0.000000] [<ffffffff810632d1>] lock_acquire+0x93/0xb1
[ +0.000000] [<ffffffffa0022339>] ? spin_lock+0x9/0xb [bluetooth]
[ +0.000000] [<ffffffff8105f3d8>] ? lock_release_holdtime.part.22+0x4e/0x55
[ +0.000000] [<ffffffff814f6038>] _raw_spin_lock+0x40/0x74
[ +0.000000] [<ffffffffa0022339>] ? spin_lock+0x9/0xb [bluetooth]
[ +0.000000] [<ffffffff814f6936>] ? _raw_spin_unlock+0x23/0x36
[ +0.000000] [<ffffffffa0022339>] spin_lock+0x9/0xb [bluetooth]
[ +0.000000] [<ffffffffa00230cc>] sco_conn_del+0x76/0xbb [bluetooth]
[ +0.000000] [<ffffffffa002391d>] sco_connect_cfm+0x2da/0x2e9 [bluetooth]
[ +0.000000] [<ffffffffa000862a>] hci_proto_connect_cfm+0x38/0x65 [bluetooth]
[ +0.000000] [<ffffffffa0008d30>] hci_sync_conn_complete_evt.isra.79+0x11a/0x13e [bluetooth]
[ +0.000000] [<ffffffffa000cd96>] hci_event_packet+0x153b/0x239d [bluetooth]
[ +0.000000] [<ffffffff814f68ff>] ? _raw_spin_unlock_irqrestore+0x48/0x5c
[ +0.000000] [<ffffffffa00025f6>] hci_rx_work+0xf3/0x2e3 [bluetooth]
[ +0.000000] [<ffffffff8103efed>] process_one_work+0x1dc/0x30b
[ +0.000000] [<ffffffff8103ef83>] ? process_one_work+0x172/0x30b
[ +0.000000] [<ffffffff8103e07f>] ? spin_lock_irq+0x9/0xb
[ +0.000000] [<ffffffff8103fc8d>] worker_thread+0x123/0x1d2
[ +0.000000] [<ffffffff8103fb6a>] ? manage_workers+0x240/0x240
[ +0.000000] [<ffffffff81044211>] kthread+0x9d/0xa5
[ +0.000000] [<ffffffff81044174>] ? __kthread_parkme+0x60/0x60
[ +0.000000] [<ffffffff814f75bc>] ret_from_fork+0x7c/0xb0
[ +0.000000] [<ffffffff81044174>] ? __kthread_parkme+0x60/0x60
[ +0.000000] Code: d7 44 89 8d 50 ff ff ff 4c 89 95 58 ff ff ff e8 44 fc ff ff 44 8b 8d 50 ff ff ff 48 85 c0 4c 8b 95 58 ff ff ff 0f 84 7a 04 00 00 <f0> ff 80 98 01 00 00 83 3d 25 41 a7 00 00 45 8b b5 e8 05 00 00
[ +0.000000] RIP [<ffffffff810620dd>] __lock_acquire+0xed/0xe82
[ +0.000000] RSP <ffff88003c3c19d8>
[ +0.000000] CR2: 0000000000000199
[ +0.000000] ---[ end trace e73cd3b52352dd34 ]---
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Tested-by: Frederic Dalleau <frederic.dalleau@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff7f3efb9abf986f4ecd8793a9593f7ca4d6431a upstream.
The current Tilera boot infrastructure now provides the initramfs
to Linux as a Tilera-hypervisor file named "initramfs", rather than
"initramfs.cpio.gz", as before. (This makes it reasonable to use
other compression techniques than gzip on the file without having to
worry about the name causing confusion.) Adapt to use the new name,
but also fall back to checking for the old name.
Cc'ing to stable so that older kernels will remain compatible with
newer Tilera boot infrastructure.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1166fde6a923c30f4351515b6a9a1efc513e7d00 upstream.
We need to be careful when testing task->tk_waitqueue in
rpc_wake_up_task_queue_locked, because it can be changed while we
are holding the queue->lock.
By adding appropriate memory barriers, we can ensure that it is safe to
test task->tk_waitqueue for equality if the RPC_TASK_QUEUED bit is set.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 6ef9e2f6d12ce9e2120916804d2ddd46b954a70b upstream.
If CONFIG_MAC80211_MESH is not set, cfg80211 will now allow advertising
interface combinations with NL80211_IFTYPE_MESH_POINT present.
Add appropriate ifdefs to avoid running into errors.
[Backported for 3.8-stable. Removed code of simultaneous AP and mesh
mode added in 4a5fc6d 3.9-rc1.]
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9d1400cf79afb49584b4873eb22cd5130cb341db upstream.
Atomic pool should always be allocated from DMA zone if such zone is
available in the system to avoid issues caused by limited dma mask of
any of the devices used for making an atomic allocation.
Reported-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db9e51617faad3a54d10b7cb340a82688ec0232d upstream.
Commit 032ec49f5351e9cb242b1a1c367d14415043ab95 (usb: musb: drop useless
board_mode usage) introduced a typo that breaks the build.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
[ Fixed commit message ]
Signed-off-by: Michael Riesch <michael.riesch@omicron.at>
Cc: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5492bf3d5655b4954164f69c02955a7fca267611 upstream.
Add missing get_icount field to two-port driver.
The two-port driver was not updated when switching to the new icount
interface in commit 0bca1b913aff ("tty: Convert the USB drivers to the
new icount interface").
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 618aa1068df29c37a58045fe940f9106664153fd upstream.
Remove bogus disconnect test introduced by 95bef012e ("USB: more serial
drivers writing after disconnect") which prevented queued data from
being freed on disconnect.
The possible IO it was supposed to prevent is long gone.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89b1f39eb4189de745fae554b0d614d87c8d5c63 upstream.
For large UDF filesystems with 512-byte blocks the number of necessary
bitmap blocks is larger than 2^16 so s_nr_groups in udf_bitmap overflows
(the number will overflow for filesystems larger than 128 GB with
512-byte blocks). That results in ENOSPC errors despite the filesystem
has plenty of free space.
Fix the problem by changing s_nr_groups' type to 'int'. That is enough
even for filesystems 2^32 blocks (UDF maximum) and 512-byte blocksize.
Reported-and-tested-by: v10lator@myway.de
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Jim Trigg <jtrigg@spamcop.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 33f767d767e9a684e9cd60704d4c049a2014c8d5 upstream.
Observe that acpi_get_child() doesn't need to use the helper
struct acpi_find_child structure and change it to work without it.
Also, using acpi_get_object_info() to get the output of _ADR for the
given device is overkill, because that function does much more than
just evaluating _ADR (let alone the additional memory allocation
done by it).
Moreover, acpi_get_child() doesn't need to loop any more once it has
found a matching handle, so make it stop in that case. To prevent
the results from changing, make it use do_acpi_find_child() as
a post-order callback.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca0ba26fbbd2d81c43085df49ce0abfe34535a90 upstream.
The 'CONFIG_' prefix is not implicit in IS_ENABLED().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ec0971ba5372a4dfa753f232449d23a8fd98490e upstream.
We know that with some firmware implementations writing too much data to
UEFI variables can lead to bricking machines. Recent changes attempt to
address this issue, but for some it may still be prudent to avoid
writing large amounts of data until the solution has been proven on a
wide variety of hardware.
Crash dumps or other data from pstore can potentially be a large data
source. Add a pstore_module parameter to efivars to allow disabling its
use as a backend for pstore. Also add a config option,
CONFIG_EFI_VARS_PSTORE_DEFAULT_DISABLE, to allow setting the default
value of this paramter to true (i.e. disabled by default).
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed9dc8ce7a1c8115dba9483a9b51df8b63a2e0ef upstream.
Add a new option, CONFIG_EFI_VARS_PSTORE, which can be set to N to
avoid using efivars as a backend to pstore, as some users may want to
compile out the code completely.
Set the default to Y to maintain backwards compatability, since this
feature has always been enabled until now.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d7971051e4df825e0bc11b995e87bfe86355b8e5 upstream.
Make sure the interface is not released before our serial device.
Note that drivers are still not allowed to access the interface in
any way that may interfere with another driver that may have gotten
bound to the same interface after disconnect returns.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3416905ba058e43112ad7b1b4859797f027f5a07 upstream.
This patch fixes an "off-by-one" bug found in
581791f (FunctionFS: enable multiple functions).
During gfs_bind/gfs_unbind the functionfs_bind/functionfs_unbind should be
called for every functionfs instance. With the "i" pre-decremented they
were not called for the zeroth instance.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[ balbi@ti.com : added offending commit's subject ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d714aaf649460cbfd5e82e75520baa856b4fa0a0 upstream.
This patch (as1670) fixes a regression caused by commit
6402c796d3b4205d3d7296157956c5100a05d7d6 (USB: EHCI: work around
silicon bug in Intel's EHCI controllers). The workaround goes through
two IAA cycles for each QH being unlinked. During the first cycle,
the QH is not added to the async_iaa list (because it isn't fully gone
from the hardware yet), which means that list will be empty.
Unfortunately, I forgot to update the IAA watchdog timer routine. It
thinks that an empty async_iaa list means the timer expiration was an
error, which isn't true any more. This problem didn't show up during
initial testing because the controllers being tested all had working
IAA interrupts. But not all controllers do, and when the watchdog
timer expires, the empty-list check prevents the second IAA cycle from
starting. As a result, URB unlinks never complete. The check needs
to be removed.
Among the symptoms of the regression are processes stuck in D wait
states and hangs during system shutdown.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Reported-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a40f324541ee61c22146214349c2ce9f5c30bcf upstream.
This patch (as1663) fixes a regression caused by commit
6e0c3339a6f19d748f16091d0a05adeb1e1f822b (USB: EHCI: unlink one async
QH at a time). In order to avoid keeping multiple QHs in an unusable
intermediate state, that commit changed unlink_empty_async() so that
it unlinks only one empty QH at a time.
However, when the EHCI root hub is suspended, _all_ async QHs need to
be unlinked. ehci_bus_suspend() used to do this by calling
unlink_empty_async(), but now this only unlinks one of the QHs, not
all of them.
The symptom is that when the root hub is resumed, USB communications
don't work for some period of time. This is because ehci-hcd doesn't
realize it needs to restart the async schedule; it assumes that
because some QHs are already on the schedule, the schedule must be
running.
The easiest way to fix the problem is add a new function that unlinks
all the async QHs when the root hub is suspended.
This patch should be applied to all kernels that have the 6e0c3339a6f1
commit.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Adrian Bassett <adrian.bassett@hotmail.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb25505fc604292c70fc02143fc102f54c8595f0 upstream.
Unregister tty device in disconnect as is required by the USB stack.
By deferring unregistration to when the last tty reference is dropped,
the parent interface device can get unregistered before the child
resulting in broken hotplug events being generated when the tty is
finally closed:
KERNEL[2290.798128] remove /devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:3.1 (usb)
KERNEL[2290.804589] remove /devices/pci0000:00/0000:00:1d.7/usb2/2-1 (usb)
KERNEL[2294.554799] remove /2-1:3.1/tty/ttyACM0 (tty)
The driver must deal with tty callbacks after disconnect by checking the
disconnected flag. Specifically, further opens must be prevented and
this is already implemented.
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00eed9c814cb8f281be6f0f5d8f45025dc0a97eb upstream.
xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.
v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8264340e694604863255cc0276491d17c402390 upstream.
According to XHCI specification (5.5.2.1) the IP is bit 0 and IE is bit 1
of IMAN register. Previously their definitions were reversed.
Even though there are no ill effects being observed from the swapped
definitions (because IMAN_IP is RW1C and in legacy PCI case we come in
with it already set to 1 so it was clearing itself even though we were
setting IMAN_IE instead of IMAN_IP), we should still correct the values.
This patch should be backported to kernels as old as 2.6.36, that
contain the commit 4e833c0b87a30798e67f06120cecebef6ee9644c "xhci: don't
re-enable IE constantly".
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66db3feb486c01349f767b98ebb10b0c3d2d021b upstream.
The increment of "to" in copy_user_handle_tail() will have incremented
before a failure has been noted. This causes us to skip a byte in the
failure case.
Only do the increment when assured there is no failure.
Signed-off-by: CQ Tang <cq.tang@intel.com>
Link: http://lkml.kernel.org/r/20130318150221.8439.993.stgit@phlsvslse11.ph.intel.com
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7dc19b8652c862d5b7c4d2339bd3c428bd29c4a upstream.
Currently tick_check_broadcast_device doesn't reject clock_event_devices
with CLOCK_EVT_FEAT_DUMMY, and may select them in preference to real
hardware if they have a higher rating value. In this situation, the
dummy timer is responsible for broadcasting to itself, and the core
clockevents code may attempt to call non-existent callbacks for
programming the dummy, eventually leading to a panic.
This patch makes tick_check_broadcast_device always reject dummy timers,
preventing this problem.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e49dbbf3e770aa590a8a464ac4978a09027060b9 upstream.
vfs_writev() updates the offset argument - but the code then passes the
offset to vfs_fsync_range(). Since offset now points to the offset after
what was just written, this is probably not what was intended
Introduced by face15025ffdf664de95e86ae831544154d26c9c "nfsd: use
vfs_fsync_range(), not O_SYNC, for stable writes".
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Zach Brown <zab@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8dfcffd0472a0f353f34a567ad3f53568914d04 upstream.
A number of problems can occur due to races between
resync/recovery and discard.
- if sync_request calls handle_stripe() while a discard is
happening on the stripe, it might call handle_stripe_clean_event
before all of the individual discard requests have completed
(so some devices are still locked, but not all).
Since commit ca64cae96037de16e4af92678814f5d4bf0c1c65
md/raid5: Make sure we clear R5_Discard when discard is finished.
this will cause R5_Discard to be cleared for the parity device,
so handle_stripe_clean_event() will not be called when the other
devices do become unlocked, so their ->written will not be cleared.
This ultimately leads to a WARN_ON in init_stripe and a lock-up.
- If handle_stripe_clean_event() does clear R5_UPTODATE at an awkward
time for resync, it can lead to s->uptodate being less than disks
in handle_parity_checks5(), which triggers a BUG (because it is
one).
So:
- keep R5_Discard on the parity device until all other devices have
completed their discard request
- make sure we don't try to have a 'discard' and a 'sync' action at
the same time.
This involves a new stripe flag to we know when a 'discard' is
happening, and the use of R5_Overlap on the parity disk so when a
discard is wanted while a sync is active, so we know to wake up
the discard at the appropriate time.
Discard support for RAID5 was added in 3.7, so this is suitable for
any -stable kernel since 3.7.
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e3620a3ad52609f64a2402e4b59300afb4b83b77 upstream.
MD RAID5: Fix kernel oops when RAID4/5/6 is used via device-mapper
Commit a9add5d (v3.8-rc1) added blktrace calls to the RAID4/5/6 driver.
However, when device-mapper is used to create RAID4/5/6 arrays, the
mddev->gendisk and mddev->queue fields are not setup. Therefore, calling
things like trace_block_bio_remap will cause a kernel oops. This patch
conditionalizes those calls on whether the proper fields exist to make
the calls. (Device-mapper will call trace_block_bio_remap on its own.)
This patch is suitable for the 3.8.y stable kernel.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce7d363aaf1e28be8406a2976220944ca487e8ca upstream.
Since commit 1ed850f356a0a422013846b5291acff08815008b
md/raid5: make sure to_read and to_write never go negative.
It has been possible for handle_stripe_dirtying to be called
when there isn't actually any work to do.
It then calls schedule_reconstruction() which will set R5_LOCKED
on the parity block(s) even when nothing else is happening.
This then causes problems in do_release_stripe().
So add checks to schedule_reconstruction() so that if it doesn't
find anything to do, it just aborts.
This bug was introduced in v3.7, so the patch is suitable
for -stable kernels since then.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18e4321276fcf083b85b788fee7cf15be29ed72a upstream.
A problem was found on PC's with the SB700 chipset: The PC fails to
load BIOS after running the 3.8.x kernel until the power is completely
cut off. It occurs in all 3.8.x versions and the mainline version as of
2/4. The issue does not occur with the 3.7.x builds.
There are two methods for accessing the watchdog registers.
1. Re-programming a resource address obtained by allocate_resource()
to chipset.
2. Use the direct memory-mapped IO access.
The method 1 can be used by all the chipsets (SP5100, SB7x0, SB8x0 or
later). However, experience shows that only PC with the SB8x0 (or
later) chipsets can use the method 2.
This patch removes the method 1, because the critical problem was found.
That's why the watchdog timer was able to be used on SP5100 and SB7x0
chipsets until now.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1116835
Link: https://lkml.org/lkml/2013/2/14/271
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81fc933f176cd95f757bfc8a98109ef422598b79 upstream.
The AcpiMmioSel bit is bit 1 in the AcpiMmioEn register, but the current
sp5100_tco driver is using bit 2.
See 2.3.3 Power Management (PM) Registers page 150 of the
AMD SB800-Series Southbridges Register Reference Guide [1].
AcpiMmioEn - RW – 8/16/32 bits - [PM_Reg: 24h]
Field Name Bits Default Description
AcpiMMioDecodeEn 0 0b Set to 1 to enable AcpiMMio space.
AcpiMMIoSel 1 0b Set AcpiMMio registers to be memory-mapped or IO-mapped space.
0: Memory-mapped space
1: I/O-mapped space
The sp5100_tco driver expects zero as a value of AcpiMmioSel (bit 1).
Fortunately, no problems were caused by this typo, because the default
value of the undocumented misused bit 2 seems to be zero.
However, the sp5100_tco driver should use the correct bitmask value.
[1] http://support.amd.com/us/Embedded_TechDocs/45482.pdf
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ee9e2aa7b31427303466776f455d43e5e3c9275 upstream.
Commit f0dc117abdfa ("IPoIB: Fix TX queue lockup with mixed UD/CM
traffic") attempts to solve an issue where unprocessed UD send
completions can deadlock the netdev.
The patch doesn't fully resolve the issue because if more than half
the tx_outstanding's were UD and all of the destinations are RC
reachable, arming the CQ doesn't solve the issue.
This patch uses the IB_CQ_REPORT_MISSED_EVENTS on the
ib_req_notify_cq(). If the rc is above 0, the UD send cq completion
callback is called directly to re-arm the send completion timer.
This issue is seen in very large parallel filesystem deployments
and the patch has been shown to correct the issue.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b405bfa84063bfa35621d2d6879f52693c614b0 upstream.
In data=journal mode, if we unmount the file system before a
transaction has a chance to complete, when the journal inode is being
evicted, we can end up calling into jbd2_log_wait_commit() for the
last transaction, after the journalling machinery has been shut down.
Arguably we should adjust ext4_should_journal_data() to return FALSE
for the journal inode, but the only place it matters is
ext4_evict_inode(), and so to save a bit of CPU time, and to make the
patch much more obviously correct by inspection(tm), we'll fix it by
explicitly not trying to waiting for a journal commit when we are
evicting the journal inode, since it's guaranteed to never succeed in
this case.
This can be easily replicated via:
mount -t ext4 -o data=journal /dev/vdb /vdb ; umount /vdb
------------[ cut here ]------------
WARNING: at /usr/projects/linux/ext4/fs/jbd2/journal.c:542 __jbd2_log_start_commit+0xba/0xcd()
Hardware name: Bochs
JBD2: bad log_start_commit: 3005630206 3005630206 0 0
Modules linked in:
Pid: 2909, comm: umount Not tainted 3.8.0-rc3 #1020
Call Trace:
[<c015c0ef>] warn_slowpath_common+0x68/0x7d
[<c02b7e7d>] ? __jbd2_log_start_commit+0xba/0xcd
[<c015c177>] warn_slowpath_fmt+0x2b/0x2f
[<c02b7e7d>] __jbd2_log_start_commit+0xba/0xcd
[<c02b8075>] jbd2_log_start_commit+0x24/0x34
[<c0279ed5>] ext4_evict_inode+0x71/0x2e3
[<c021f0ec>] evict+0x94/0x135
[<c021f9aa>] iput+0x10a/0x110
[<c02b7836>] jbd2_journal_destroy+0x190/0x1ce
[<c0175284>] ? bit_waitqueue+0x50/0x50
[<c028d23f>] ext4_put_super+0x52/0x294
[<c020efe3>] generic_shutdown_super+0x48/0xb4
[<c020f071>] kill_block_super+0x22/0x60
[<c020f3e0>] deactivate_locked_super+0x22/0x49
[<c020f5d6>] deactivate_super+0x30/0x33
[<c0222795>] mntput_no_expire+0x107/0x10c
[<c02233a7>] sys_umount+0x2cf/0x2e0
[<c02233ca>] sys_oldumount+0x12/0x14
[<c08096b8>] syscall_call+0x7/0xb
---[ end trace 6a954cc790501c1f ]---
jbd2_log_wait_commit: error: j_commit_request=-1289337090, tid=0
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f42f80a8f08d4c3f52c4267361241885d5dee3a upstream.
Currently when converting extent to initialized, we have to decide
whether to zeroout part/all of the uninitialized extent in order to
avoid extent tree growing rapidly.
The decision is made by comparing the size of the extent with the
configurable value s_extent_max_zeroout_kb which is in kibibytes units.
However when converting it to number of blocks we currently use it as it
was in bytes. This is obviously bug and it will result in ext4 _never_
zeroout extents, but rather always split and convert parts to
initialized while leaving the rest uninitialized in default setting.
Fix this by using s_extent_max_zeroout_kb as kibibytes.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90ba983f6889e65a3b506b30dc606aa9d1d46cd2 upstream.
A user who was using a 8TB+ file system and with a very large flexbg
size (> 65536) could cause the atomic_t used in the struct flex_groups
to overflow. This was detected by PaX security patchset:
http://forums.grsecurity.net/viewtopic.php?f=3&t=3289&p=12551#p12551
This bug was introduced in commit 9f24e4208f7e, so it's been around
since 2.6.30. :-(
Fix this by using an atomic64_t for struct orlav_stats's
free_clusters.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29f86e66428ee083aec106cca1748dc63d98ce23 upstream.
Device stucks on filesystem writes, unless following quirk is passed:
echo 04e8:5136:m > /sys/module/usb_storage/parameters/quirks
Add corresponding entry to unusual_devs.h
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a2256702e47f68f921dfad41b1764d05c572329 upstream.
This commit fixes a wrong return value of the number of the allocated
blocks in ext4_split_extent. When the length of blocks we want to
allocate is greater than the length of the current extent, we return a
wrong number. Let's see what happens in the following case when we
call ext4_split_extent().
map: [48, 72]
ex: [32, 64, u]
'ex' will be split into two parts:
ex1: [32, 47, u]
ex2: [48, 64, w]
'map->m_len' is returned from this function, and the value is 24. But
the real length is 16. So it should be fixed.
Meanwhile in this commit we use right length of the allocated blocks
when get_reserved_cluster_alloc in ext4_ext_handle_uninitialized_extents
is called.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ad56edad089b56300fd13bb9eeb7d0424d978239 upstream.
jbd2_journal_dirty_metadata() didn't get a reference to journal_head it
was working with. This is OK in most of the cases since the journal head
should be attached to a transaction but in rare occasions when we are
journalling data, __ext4_journalled_writepage() can race with
jbd2_journal_invalidatepage() stripping buffers from a page and thus
journal head can be freed under hands of jbd2_journal_dirty_metadata().
Fix the problem by getting own journal head reference in
jbd2_journal_dirty_metadata() (and also in jbd2_journal_set_triggers()
which can possibly have the same issue).
Reported-by: Zheng Liu <gnehzuil.liu@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f853c616883a8de966873a1dab283f1369e275a1 upstream.
We've had several reports of people attempting to mount Windows 8 shares
and getting failures with a return code of -EINVAL. The default sec=
mode changed recently to sec=ntlmssp. With that, we expect and parse a
SPNEGO blob from the server in the NEGOTIATE reply.
The current decode_negTokenInit function first parses all of the
mechTypes and then tries to parse the rest of the negTokenInit reply.
The parser however currently expects a mechListMIC or nothing to follow the
mechTypes, but Windows 8 puts a mechToken field there instead to carry
some info for the new NegoEx stuff.
In practice, we don't do anything with the fields after the mechTypes
anyway so I don't see any real benefit in continuing to parse them.
This patch just has the kernel ignore the fields after the mechTypes.
We'll probably need to reinstate some of this if we ever want to support
NegoEx.
Reported-by: Jason Burgess <jason@jacknife2.dns2go.com>
Reported-by: Yan Li <elliot.li.tech@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24261fc23db950951760d00c188ba63cc756b932 upstream.
cifsFileInfo objects hold references to dentries and it is possible that
these will still be around in workqueues when VFS decides to kill super
block during unmount.
This results in panics like this one:
BUG: Dentry ffff88001f5e76c0{i=66b4a,n=1M-2} still in use (1) [unmount of cifs cifs]
------------[ cut here ]------------
kernel BUG at fs/dcache.c:943!
[..]
Process umount (pid: 1781, threadinfo ffff88003d6e8000, task ffff880035eeaec0)
[..]
Call Trace:
[<ffffffff811b44f3>] shrink_dcache_for_umount+0x33/0x60
[<ffffffff8119f7fc>] generic_shutdown_super+0x2c/0xe0
[<ffffffff8119f946>] kill_anon_super+0x16/0x30
[<ffffffffa036623a>] cifs_kill_sb+0x1a/0x30 [cifs]
[<ffffffff8119fcc7>] deactivate_locked_super+0x57/0x80
[<ffffffff811a085e>] deactivate_super+0x4e/0x70
[<ffffffff811bb417>] mntput_no_expire+0xd7/0x130
[<ffffffff811bc30c>] sys_umount+0x9c/0x3c0
[<ffffffff81657c19>] system_call_fastpath+0x16/0x1b
Fix this by making each cifsFileInfo object hold a reference to cifs
super block, which implicitly keeps VFS super block around as well.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reported-and-Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa8d387dc3f62062a6b4afbbb2a3438094fd8584 upstream.
Fixes a segfault on asics without a blit callback.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=62239
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f612b23a17dce86fef75407e698de6243cc99a1 upstream.
Need to adjust the backend map depending on which RB is
enabled. This is the trinity equivalent of:
f7eb97300832f4fe5fe916c5d84cd2e25169330e
May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=57919
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa3daf9aa74a3ac1c87d8188a43d283d06720032 upstream.
We weren't properly tearing down the VM sub-alloctor
on suspend leading to bogus VM PTs on resume.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=60439
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Dmitry Cherkasov <Dmitrii.Cherkasov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4d170633fde379f39a90f8a5e7eb619b5d1144d upstream.
Richland APUs are a new version of the Trinity APUs
with performance and power management improvements.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b75bbaa038ffc426e88ea3df6c4ae11834fc3e4f upstream.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 260b3f1291a75a580d22ce8bfb1499c617272716 upstream.
While testing the mgag200 kms driver on the HP ProLiant Gen8, a
bug was seen. Once the bootloader would load the selected kernel,
the screen would go black. At first it was assumed that the
mgag200 kms driver was hanging. But after setting up the grub
serial output, it was seen that the driver was being loaded
properly. After trying serval monitors, one finaly displayed
the message "Frequency Out of Range". By comparing the kms pll
algorithm with the previous mgag200 xorg driver pll algorithm,
discrepencies were found. Once the kms pll algorithm was
modified, the expected pll values were produced. This fix was
tested on several monitors of varying native resolutions.
Signed-off-by: Julia Lemire <jlemire@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b6b7813b198b578aa7e04e4047ddb8225c37b7f upstream.
A deadlock was found in the prefetch code in the dm verity map
function. This patch fixes this by transferring the prefetch
to a worker thread and skipping it completely if kmalloc fails.
If generic_make_request is called recursively, it queues the I/O
request on the current->bio_list without making the I/O request
and returns. The routin |
