| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (62 commits)
DaVinci: DM646x - platform changes for vpif capture and display drivers
davinci: DM355 - platform changes for vpfe capture
davinci: DM644x platform changes for vpfe capture
davinci: audio: move tlv320aic33 i2c setup into board files
DaVinci: EDMA: Adding 2 new APIs for allocating/freeing PARAMs
DaVinci: DM365: Adding entries for DM365 IRQ's
DaVinci: DM355: Adding PINMUX entries for DM355 Display
davinci: Handle pinmux conflict between mmc/sd and nor flash
davinci: Add NOR flash support for da850/omap-l138
davinci: Add NAND flash support for DA850/OMAP-L138
davinci: Add MMC/SD support for da850/omap-l138
davinci: Add platform support for da850/omap-l138 GLCD
davinci: Macro to convert GPIO signal to GPIO pin number
davinci: Audio support for DA850/OMAP-L138 EVM
davinci: Audio support for DA830 EVM
davinci: Correct the number of GPIO pins for da850/omap-l138
davinci: Configure MDIO pins for EMAC
DaVinci: DM365: Add Support for new Revision of silicon
DaVinci: DM365: Fix Compilation issue due to PINMUX entry
DaVinci: EDMA: Updating default queue handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (47 commits)
OMAP clock: use debugfs_remove_recursive() for rewinding
OMAP2/3/4 core: create omap_device layer
OMAP: omap_hwmod: call omap_hwmod init at boot; create interconnects
OMAP2/3/4: create omap_hwmod layer
OMAP2/3 board-*.c files: read bootloader configuration earlier
OMAP2/3/4 PRCM: add module IDLEST wait code
OMAP2/3 PM: create the OMAP PM interface and add a default OMAP PM no-op layer
OMAP3 clock: remove superfluous calls to omap2_init_clk_clkdm
OMAP clock: associate MPU clocks with the mpu_clkdm
OMAP3 clock: Fixed processing of bootarg 'mpurate'
OMAP: SDRC: Add several new register definitions
OMAP: powerdomain: Fix overflow when doing powerdomain deps lookups.
OMAP: PM: Added suspend target state control to debugfs for OMAP3
OMAP: PM debug: Add PRCM register dump support
OMAP: PM debug: make powerdomains use PM-debug counters
OMAP: PM: Add pm-debug counters
OMAP: PM: Add closures to clkdm_for_each and pwrdm_for_each.
OMAP: PM: Hook into PM counters
OMAP: PM counter infrastructure.
OMAP3: PM: fix lockdep warning caused by omap3_pm_init
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use kernel_sendpage
dlm: fix connection close handling
dlm: fix double-release of socket in error exit path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
ext3: Flush disk caches on fsync when needed
ext3: Add locking to ext3_do_update_inode
ext3: Fix possible deadlock between ext3_truncate() and ext3_get_blocks()
jbd: Annotate transaction start also for journal_restart()
jbd: Journal block numbers can ever be only 32-bit use unsigned int for them
ext3: Update MAINTAINERS for ext3 and JBD
JBD: round commit timer up to avoid uncommitted transaction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix NULL ptr regression in powernow-k8
[CPUFREQ] Create a blacklist for processors that should not load the acpi-cpufreq module.
[CPUFREQ] Powernow-k8: Enable more than 2 low P-states
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)
[CPUFREQ] ondemand - Use global sysfs dir for tuning settings
[CPUFREQ] Introduce global, not per core: /sys/devices/system/cpu/cpufreq
[CPUFREQ] Bail out of cpufreq_add_dev if the link for a managed CPU got created
[CPUFREQ] Factor out policy setting from cpufreq_add_dev
[CPUFREQ] Factor out interface creation from cpufreq_add_dev
[CPUFREQ] Factor out symlink creation from cpufreq_add_dev
[CPUFREQ] cleanup up -ENOMEM handling in cpufreq_add_dev
[CPUFREQ] Reduce scope of cpu_sys_dev in cpufreq_add_dev
[CPUFREQ] update Doc for cpuinfo_cur_freq and scaling_cur_freq
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (34 commits)
time: Prevent 32 bit overflow with set_normalized_timespec()
clocksource: Delay clocksource down rating to late boot
clocksource: clocksource_select must be called with mutex locked
clocksource: Resolve cpu hotplug dead lock with TSC unstable, fix crash
timers: Drop a function prototype
clocksource: Resolve cpu hotplug dead lock with TSC unstable
timer.c: Fix S/390 comments
timekeeping: Fix invalid getboottime() value
timekeeping: Fix up read_persistent_clock() breakage on sh
timekeeping: Increase granularity of read_persistent_clock(), build fix
time: Introduce CLOCK_REALTIME_COARSE
x86: Do not unregister PIT clocksource on PIT oneshot setup/shutdown
clocksource: Avoid clocksource watchdog circular locking dependency
clocksource: Protect the watchdog rating changes with clocksource_mutex
clocksource: Call clocksource_change_rating() outside of watchdog_lock
timekeeping: Introduce read_boot_clock
timekeeping: Increase granularity of read_persistent_clock()
timekeeping: Update clocksource with stop_machine
timekeeping: Add timekeeper read_clock helper functions
timekeeping: Move NTP adjusted clock multiplier to struct timekeeper
...
Fix trivial conflict due to MIPS lemote -> loongson renaming.
|
|
Commit ac89a9174 ("pty: don't limit the writes to 'pty_space()' inside
'pty_write()'") removed the pty_space() checking, in order to let the
regular tty buffer code limit the buffering itself.
That was all good, but as a subtle side effect it meant that we'd be
doing a tty_wakeup() even in the case where the buffers were all filled
up, and didn't actually make any progress on the write.
Which sounds innocuous, but it interacts very badly with the ppp_async
code, which has an infinite loop in ppp_async_push() that tries to push
out data to the tty. When we call tty_wakeup(), that loop ends up
thinking that progress was made (see the subtle interactions between
XMIT_WAKEUP and 'tty_stuffed' for details). End result: one unhappy ppp
user.
Fixed by noticing when tty_insert_flip_string() didn't actually do
anything, and then not doing any more processing (including, very much
not calling tty_wakeup()).
Bisected-and-tested-by: Peter Volkov <pva@gentoo.org>
Cc: stable@kernel.org (2.6.31)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (21 commits)
x86, mce: Fix compilation with !CONFIG_DEBUG_FS in mce-severity.c
x86, mce: CE in last bank prevents panic by unknown MCE
x86, mce: Fake panic support for MCE testing
x86, mce: Move debugfs mce dir creating to mce.c
x86, mce: Support specifying raise mode for software MCE injection
x86, mce: Support specifying context for software mce injection
x86, mce: fix reporting of Thermal Monitoring mechanism enabled
x86, mce: remove never executed code
x86, mce: add missing __cpuinit tags
x86, mce: fix "mce" boot option handling for CONFIG_X86_NEW_MCE
x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs
x86: mce: Lower maximum number of banks to architecture limit
x86: mce: macros to compute banks MSRs
x86: mce: Move per bank data in a single datastructure
x86: mce: Move code in mce.c
x86: mce: Rename CONFIG_X86_NEW_MCE to CONFIG_X86_MCE
x86: mce: Remove old i386 machine check code
x86: mce: Update X86_MCE description in x86/Kconfig
x86: mce: Make CONFIG_X86_ANCIENT_MCE dependent on CONFIG_X86_MCE
x86, mce: use atomic_inc_return() instead of add by 1
...
Manually fixed up trivial conflicts:
Documentation/feature-removal-schedule.txt
arch/x86/kernel/cpu/mcheck/mce.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
sched: Fix SD_POWERSAVING_BALANCE|SD_PREFER_LOCAL vs SD_WAKE_AFFINE
sched: Stop buddies from hogging the system
sched: Add new wakeup preemption mode: WAKEUP_RUNNING
sched: Fix TASK_WAKING & loadaverage breakage
sched: Disable wakeup balancing
sched: Rename flags to wake_flags
sched: Clean up the load_idx selection in select_task_rq_fair
sched: Optimize cgroup vs wakeup a bit
sched: x86: Name old_perf in a unique way
sched: Implement a gentler fair-sleepers feature
sched: Add SD_PREFER_LOCAL
sched: Add a few SYNC hint knobs to play with
sched: Fix sync wakeups again
sched: Add WF_FORK
sched: Rename sync arguments
sched: Rename select_task_rq() argument
sched: Feature to disable APERF/MPERF cpu_power
x86: sched: Provide arch implementations using aperf/mperf
x86: Add generic aperf/mperf code
x86: Move APERF/MPERF into a X86_FEATURE
...
Fix up trivial conflict in arch/x86/include/asm/processor.h due to
nearby addition of amd_get_nb_id() declaration from the EDAC merge.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pat: don't use rb-tree based lookup in reserve_memtype()
x86: Increase MIN_GAP to include randomized stack
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (44 commits)
vsnprintf: remove duplicate comment of vsnprintf
softirq: add BLOCK_IOPOLL to softirq_to_name
oprofile: fix oprofile regression: select RING_BUFFER_ALLOW_SWAP
tracing: switch function prints from %pf to %ps
vsprintf: add %ps that is the same as %pS but is like %pf
tracing: Fix minor bugs for __unregister_ftrace_function_probe
tracing: remove notrace from __kprobes annotation
tracing: optimize global_trace_clock cachelines
MAINTAINERS: Update tracing tree details
ftrace: document function and function graph implementation
tracing: make testing syscall events a separate configuration
tracing: remove some unused macros
ftrace: add compile-time check on F_printk()
tracing: fix F_printk() typos
tracing: have TRACE_EVENT macro use __flags to not shadow parameter
tracing: add static to generated TRACE_EVENT functions
ring-buffer: typecast cmpxchg to fix PowerPC warning
tracing: add filter event logic to special, mmiotrace and boot tracers
tracing: remove trace_event_types.h
tracing: use the new trace_entries.h to create format files
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
pata_amd: do not filter out valid modes in nv_mode_filter
sata_promise: update reset code
sata_promise: disable hotplug on 1st gen chips
libata: fix spurious WARN_ON_ONCE() on port freeze
ahci: restore pci_intx() handling
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Update defconfigs.
sparc: Kill PROM console driver.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
be2net: fix some cmds to use mccq instead of mbox
atl1e: fix 2.6.31-git4 -- ATL1E 0000:03:00.0: DMA-API: device driver frees DMA
pkt_sched: Fix qstats.qlen updating in dump_stats
ipv6: Log the affected address when DAD failure occurs
wl12xx: Fix print_mac() conversion.
af_iucv: fix race when queueing skbs on the backlog queue
af_iucv: do not call iucv_sock_kill() twice
af_iucv: handle non-accepted sockets after resuming from suspend
af_iucv: fix race in __iucv_sock_wait()
iucv: use correct output register in iucv_query_maxconn()
iucv: fix iucv_buffer_cpumask check when calling IUCV functions
iucv: suspend/resume error msg for left over pathes
wl12xx: switch to %pM to print the mac address
b44: the poll handler b44_poll must not enable IRQ unconditionally
ipv6: Ignore route option with ROUTER_PREF_INVALID
bonding: make ab_arp select active slaves as other modes
cfg80211: fix SME connect
rc80211_minstrel: fix contention window calculation
ssb/sdio: fix printk format warnings
p54usb: add Zcomax XG-705A usbid
...
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (51 commits)
MIPS: BCM63xx: Add integrated ethernet mac support.
MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.
MIPS: BCM63xx: Add Broadcom 63xx CPU definitions.
MIPS: Octeon: Move some platform device registration to its own file.
MIPS: Don't corrupt page tables on vmalloc fault.
MIPS: Shrink the size of tlb handler
MIPS: Alchemy: override loops_per_jiffy detection
MIPS: hw_random: Add hardware RNG for Octeon SOCs.
MIPS: Octeon: Add hardware RNG platform device.
MIPS: Remove useless zero initializations.
MIPS: Alchemy: get rid of allow_au1k_wait
MIPS: Octeon: Set kernel_uses_llsc to false on non-SMP builds.
MIPS: Allow kernel use of LL/SC to be separate from the presence of LL/SC.
MIPS: Get rid of CONFIG_CPU_HAS_LLSC
MIPS: Malta: Remove pointless use use of CONFIG_CPU_HAS_LLSC
MIPS: Rewrite clearing of ll_bit on context switch in C
MIPS: Rewrite sysmips(MIPS_ATOMIC_SET, ...) in C with inline assembler
MIPS: Consolidate all CONFIG_CPU_HAS_LLSC use in a single C file.
MIPS: Clean up linker script using new linker script macros.
MIPS: Use PAGE_SIZE in assembly instead of _PAGE_SIZE.
...
|
|
Merge reason:
Suresh Siddha (1):
x86, pat: don't use rb-tree based lookup in reserve_memtype()
... requires previous x86/pat commits already pushed to Linus.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Recent enhancement of rb-tree based lookup exposed a bug with the lookup
mechanism in the reserve_memtype() which ensures that there are no conflicting
memtype requests for the memory range.
memtype_rb_search() returns an entry which has a start address <= new start
address. And from here we traverse the linear linked list to check if there
any conflicts with the existing mappings. As the rbtree is based on the
start address of the memory range, it is quite possible that we have several
overlapped mappings whose start address is much less than new requested start
but the end is >= new requested end. This results in conflicting memtype
mappings.
Same bug exists with the old code which uses cached_entry from where
we traverse the linear linked list. But the new rb-tree code exposes this
bug fairly easily.
For now, don't use the memtype_rb_search() and always start the search from
the head of linear linked list in reserve_memtype(). Linear linked list
for most of the systems grow's to few 10's of entries(as we track memory type
of RAM pages using struct page). So we should be ok for now.
We still retain the rbtree and use it to speed up free_memtype() which
doesn't have the same bug(as we know what exactly we are searching for
in free_memtype).
Also use list_for_each_entry_from() in free_memtype() so that we start
the search from rb-tree lookup result.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <1253136483.4119.12.camel@sbs-t61.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Gringo <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
On a Compaq Presario V3000 laptop (NVIDIA MCP51 chipset), pata_amd selects
PIO0 mode for the PATA DVD-RAM drive instead of MWDMA2 which it supports:
ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4084N, KQ09, max MWDMA2
ata4: nv_mode_filter: 0x39f&0x7001->0x1, BIOS=0x0 (0x0) ACPI=0x7001 (60:600:0x11)
ata4.00: configured for PIO0
For some reason, the BIOS-set UDMA configuration returns 0 and the ACPI _GTM
reports that UDMA2 and PIO0 are enabled. This causes nv_mode_filter to end up
allowing only PIO0 and UDMA0-2. Since the drive doesn't support UDMA we end up
using PIO0.
Since the controllers should always support PIO4, MWDMA2 and UDMA2 regardless
of what cable type is used, let's make sure we don't filter out these modes
regardless of what wacky settings the BIOS is using.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.
This patch thus updates the reset code to more closely
match the reference driver:
- soft reset (pdc_reset_port):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* write reset bit in PDC_CTLSTAT before the first read
in the loop
* for 2nd gen SATA follow up with FPDMA reset and clearing
error status registers
- hard reset (pdc_sata_hardreset):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* reset ATA engine via the PCI control register
* Tejun's change to use non-waiting hardreset + follow-up SRST
I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).
Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.
The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.
Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit 54c38444fad6a99b4b19512f8f0055d69115e69e makes libata abort qcs
after the port is frozen. This is necessary to guarantee that TF
registers are accessed after the DMA engine is shutdown after an
error. However, this triggers WARN_ON_ONCE() check in
ata_qc_complete() spuriously. Move WARN_ON_ONCE() downwards such that
failing commands while frozen doesn't trigger it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit a5bfc4714b3f01365aef89a92673f2ceb1ccf246 dropped explicit
pci_intx() manipulation from ahci because it seemed unnecessary and
ahci doesn't seem to be the right place to be tweaking it if it were.
This was largely okay but there are exceptions. There was one on an
embedded platform which was fixed via firmware and now bko#14124
reports it on a HP DL320.
http://bugzilla.kernel.org/show_bug.cgi?id=14124
I still think this isn't something libata drivers should be caring
about (the only ones which are calling pci_intx() explicitly are
libata ones and one other driver) but for now reverting the change
seems to be the right thing to do.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix MSI GX620 mixer
ASoC: remove unused #include <linux/version.h>
ASoC: S3C lrsync function made to work with IRQs disabled.
ALSA: hda - Fix Dell S14 pin setup
ALSA: hda - Fix IDT92HD83* codec setup
ASoC: Fix display of stream name in DAPM debugfs
ALSA: hda - Add support for HP dv6
ALSA: hda - Fix HP/line-out initialization with IDT/STAC codecs
ALSA: hda - Set default GPIO for IDT92HD71bxx
ALSA: hda - Set default GPIO for STAC/IDT codecs
ASoC: Clean up error handling in MPC5200 DMA setup
ALSA: hda - Add missing model=auto entry for ALC269
|
|
Remove the duplicate comment of bstr_printf that is the same as the
vsnprintf.
Add the 's' option to the comment for the pointer function. This is
more of an internal function so the little duplication of the comment
here is OK.
Reported-by: Zhaolei <zhaolei@cn.fujitsu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
With BLOCK_IOPOLL_SOFTIRQ added, softirq_to_name[] and
show_softirq_name() needs to be updated.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4AB20398.8070209@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
commit 85bac32c4a52c592b857f2c360cc5ec93a097d70
ring-buffer: only enable ring_buffer_swap_cpu when needed
broke oprofile (at least on s390, but likely on all platforms).
this patch lets oprofile select RING_BUFER_ALLOW_SWAP to make
ring_buffer_swap_cpu usable for oprofile.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
LKML-Reference: <200909162156.49239.borntraeger@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robert Richter <robert.richter@amd.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
For direct function pointers (like what mcount provides) PowerPC64
requires the use of %ps, otherwise nothing is printed.
This patch converts all prints of functions retrieved through mcount
to use the %ps format from the %pf.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
On PowerPC64 function pointers do not point directly at the functions,
but instead point to pointers to the functions. The output of %pF expects
to point to a pointer to the function, whereas %pS will show the function
itself.
mcount returns the direct pointer to the function and not the pointer to
the pointer. Thus %pS must be used to show this. The function tracer
requires printing of the functions without offsets and uses the %pf
instead.
%pF produces run_local_timers+0x4/0x1f
%pf produces just run_local_timers
For PowerPC64, we need to use the direct pointer, and we only have
%pS which will produce .run_local_timers+0x4/0x1f
This patch creates a %ps that matches the %pf as %pS matches %pF.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
* fix/hda:
ALSA: hda - Fix MSI GX620 mixer
ALSA: hda - Fix Dell S14 pin setup
ALSA: hda - Fix IDT92HD83* codec setup
ALSA: hda - Add support for HP dv6
ALSA: hda - Fix HP/line-out initialization with IDT/STAC codecs
ALSA: hda - Set default GPIO for IDT92HD71bxx
ALSA: hda - Set default GPIO for STAC/IDT codecs
ALSA: hda - Add missing model=auto entry for ALC269
|
|
* fix/asoc:
ASoC: remove unused #include <linux/version.h>
ASoC: S3C lrsync function made to work with IRQs disabled.
ASoC: Fix display of stream name in DAPM debugfs
ASoC: Clean up error handling in MPC5200 DMA setup
|
|
Merge reason: Pick up kernel/softirq.c update for dependent fix.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Todo: Nothing ever detects CPU_BCM6338 but the code tests for it anyway.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There is a bunch of platform device registration in
arch/mips/cavium-octeon/setup.c. We move it to its own file in
preparation for adding more platform devices.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The code after the vmalloc_fault: label in do_page_fault() modifies
user page tables, this is not correct for 64-bit kernels.
For 64-bit kernels we should go straight to the no_context handler
skipping vmalloc_fault.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
By combining swapper_pg_dir and module_pg_dir, several if conditions
can be eliminated from the tlb exception handler. The reason they
can be combined is that, the effective virtual address of vmalloc
returned is at the bottom, and of module_alloc returned is at the
top. It also fixes the bug in vmalloc(), which happens when its
return address is not covered by the first pgd.
Signed-off-by: Wu Fei <at.wufei@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
loops_per_jiffy depends on coreclk speed; preset it instead of
letting the kernel waste precious microseconds trying to approximate it.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add a platform device for the Octeon Random Number Generator (RNG).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Eliminate the 'allow_au1k_wait' variable. MIPS kernel installs the
Alchemy-specific wait code before timer initialization; if the C0
timer must be used for timekeeping the wait function is set to NULL
which means no wait implementation is available.
As a sideeffect, the 'wait instruction available' output in
/proc/cpuinfo now correctly indicates whether 'wait' is usable.
Run-tested on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
On some CPUs, it is more efficient to disable and enable interrupts in the
kernel rather than use ll/sc for atomic operations. But if we were to set
cpu_has_llsc to false, we would break the userspace futex interface (in
asm/futex.h).
We separate the two concepts, with a new predicate kernel_uses_llsc, that
lets us disable the kernel's use of ll/sc while still allowing the futex
code to use it.
Also there were a couple of cases in bitops.h where we were using ll/sc
unconditionally even if cpu_has_llsc were false.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
CONFIG_CPU_HAS_LLSC duplicated the function of cpu_has_llsc for no good
reason and and the results if the one was enabled and the other disabled
was very unobvious. Remove it now that there are no more remaining users.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
All CPUs for Malta support LL/SC.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This also means there is now only one implementation not 3 left.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This way it doesn't have to use CONFIG_CPU_HAS_LLSC anymore.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
