| Age | Commit message (Collapse) | Author |
|---|
|
commit 60cefed485a02bd99b6299dad70666fe49245da7 upstream.
Kswapd does not in all places have the same criteria for a balanced
zone. Zones are only being reclaimed when their high watermark is
breached, but compaction checks loop over the zonelist again when the
zone does not meet the low watermark plus two times the size of the
allocation. This gets kswapd stuck in an endless loop over a small
zone, like the DMA zone, where the high watermark is smaller than the
compaction requirement.
Add a function, zone_balanced(), that checks the watermark, and, for
higher order allocations, if compaction has enough free memory. Then
use it uniformly to check for balanced zones.
This makes sure that when the compaction watermark is not met, at least
reclaim happens and progress is made - or the zone is declared
unreclaimable at some point and skipped entirely.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: George Spelvin <linux@horizon.com>
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Reported-by: Tomas Racek <tracek@redhat.com>
Tested-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[hq: Backported to 3.4: adjust context]
Signed-off-by: Qiang Huang <h.huangqiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1989b330093578ea5470bea0a00f940c444c466 upstream.
An invalid ioctl will never be valid, irrespective of whether multipath
has active paths or not. So for invalid ioctls we do not have to wait
for multipath to activate any paths, but can rather return an error
code immediately. This fix resolves numerous instances of:
udevd[]: worker [] unexpectedly returned with status 0x0100
that have been seen during testing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9baa9d9d520fb0e24cca671e430689de2d4a4b2 upstream.
It appears that in the DMA40 driver the DMA tasklet will very
often dereference memory for a descriptor just free:d from the
DMA40 slab. Nothing happens because no other part of the driver
has yet had a chance to claim this memory, but it's really
nasty to dereference free:d memory, so let's check the flag
before the descriptor is free and store it in a bool variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1362f4ea20fa63688ba6026e586d9746ff13a846 upstream.
Currently last dqput() can race with dquot_scan_active() causing it to
call callback for an already deactivated dquot. The race is as follows:
CPU1 CPU2
dqput()
spin_lock(&dq_list_lock);
if (atomic_read(&dquot->dq_count) > 1) {
- not taken
if (test_bit(DQ_ACTIVE_B, &dquot->dq_flags)) {
spin_unlock(&dq_list_lock);
->release_dquot(dquot);
if (atomic_read(&dquot->dq_count) > 1)
- not taken
dquot_scan_active()
spin_lock(&dq_list_lock);
if (!test_bit(DQ_ACTIVE_B, &dquot->dq_flags))
- not taken
atomic_inc(&dquot->dq_count);
spin_unlock(&dq_list_lock);
- proceeds to release dquot
ret = fn(dquot, priv);
- called for inactive dquot
Fix the problem by making sure possible ->release_dquot() is finished by
the time we call the callback and new calls to it will notice reference
dquot_scan_active() has taken and bail out.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9085a6422900092886da8c404e1c5340c4ff1cbf upstream.
When writing policy via /sys/fs/selinux/policy I wrote the type and class
of filename trans rules in CPU endian instead of little endian. On
x86_64 this works just fine, but it means that on big endian arch's like
ppc64 and s390 userspace reads the policy and converts it from
le32_to_cpu. So the values are all screwed up. Write the values in le
format like it should have been to start.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e3703f8cdfcf39c25c4338c3ad8e68891cca3731 upstream.
Drew Richardson reported that he could make the kernel go *boom* when hotplugging
while having perf events active.
It turned out that when you have a group event, the code in
__perf_event_exit_context() fails to remove the group siblings from
the context.
We then proceed with destroying and freeing the event, and when you
re-plug the CPU and try and add another event to that CPU, things go
*boom* because you've still got dead entries there.
Reported-by: Drew Richardson <drew.richardson@arm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/n/tip-k6v5wundvusvcseqj1si0oz0@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bdfff96c69a4d5ab9c49e60abf9e070ecd2acbb upstream.
When a kworker should die, the kworkre is notified through WORKER_DIE
flag instead of kthread_should_stop(). This, IIRC, is primarily to
keep the test synchronized inside worker_pool lock. WORKER_DIE is
first set while holding pool->lock, the lock is dropped and
kthread_stop() is called.
Unfortunately, this means that there's a slight chance that the target
kworker may see WORKER_DIE before kthread_stop() finishes and exits
and frees the target task before or during kthread_stop().
Fix it by pinning the target task before setting WORKER_DIE and
putting it after kthread_stop() is done.
tj: Improved patch description and comment. Moved pinning above
WORKER_DIE for better signify what it's protecting.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 500a91571f0a5d0d3242d83802ea2fd1faccc66e upstream.
When trying to set the minimum temperature, the driver was erroneously
writing the maximum temperature into the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6dbd46c849e071e6afc1e0cad489b0175bca9318 upstream.
Hello,
the following patch adds an entry for the PID of a Cressi Leonardo
diving computer interface to kernel 3.13.0.
It is detected as FT232RL.
Works with subsurface.
Signed-off-by: Joerg Dorchain <joerg@dorchain.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 12df84d4a80278a5b1abfec3206795291da52fc9 upstream.
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3ca4164529b875374c410193bbbac0ee960895f upstream.
acpi_processor_set_throttling() uses set_cpus_allowed_ptr() to make
sure that the (struct acpi_processor)->acpi_processor_set_throttling()
callback will run on the right CPU. However, the function may be
called from a worker thread already bound to a different CPU in which
case that won't work.
Make acpi_processor_set_throttling() use work_on_cpu() as appropriate
instead of abusing set_cpus_allowed_ptr().
Reported-and-tested-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd8ba20597f0cfef3ef65c3fd2aa92ab23d4c8e1 upstream.
Some devices have duplicate entries in there brightness levels table, ie
on my Dell Latitude E6430 the table looks like this:
[ 3.686060] acpi backlight index 0, val 80
[ 3.686095] acpi backlight index 1, val 50
[ 3.686122] acpi backlight index 2, val 5
[ 3.686147] acpi backlight index 3, val 5
[ 3.686172] acpi backlight index 4, val 5
[ 3.686197] acpi backlight index 5, val 5
[ 3.686223] acpi backlight index 6, val 5
[ 3.686248] acpi backlight index 7, val 5
[ 3.686273] acpi backlight index 8, val 6
[ 3.686332] acpi backlight index 9, val 7
[ 3.686356] acpi backlight index 10, val 8
[ 3.686380] acpi backlight index 11, val 9
etc.
Notice that brightness values 0-5 are all mapped to 5. This means that
if userspace writes any value between 0 and 5 to the brightness sysfs attribute
and then reads it, it will always return 0, which is somewhat unexpected.
This is a problem for ie gnome-settings-daemon, which uses read-modify-write
logic when the users presses the brightness up or down keys. This is done
this way to take brightness changes from other sources into account.
On this specific laptop what happens once the brightness has been set to 0,
is that gsd reads 0, adds 5, writes 5, and on the next brightness up key press
again reads 0, so things get stuck at the lowest brightness setting.
Filtering out the duplicate table entries, makes any write to brightness
read back as the written value as one would expect, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c0f5eeed0f4cef4f05b74883a7160e7edde58b6a upstream.
The reference count changes done by pci_get_device can be a little
misleading when the usage diverges from the most common scheme. The
reference count of the device passed as the last parameter is always
decreased, even if the function returns no new device. So if we are
going to try alternative device IDs, we must manually increment the
device reference count before each retry. If we don't, we end up
decreasing the reference count, and after a few modprobe/rmmod cycles
the PCI devices will vanish.
In other words and as Alan put it: without this fix the EDAC code
corrupts the PCI device list.
This fixes kernel bug #50491:
https://bugzilla.kernel.org/show_bug.cgi?id=50491
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224093927.7659dd9d@endymion.delvare
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f9c47f00ce99329b1a82e2ac4f70f0fe3db549c upstream.
It's a bit odd to see a newer device showing mod15write; however, the
reported behavior is highly consistent and other factors which could
contribute seem to have been verified well enough. Also, both
sata_sil itself and the drive are fairly outdated at this point making
the risk of this change fairly low. It is possible, probably likely,
that other drive models in the same family have the same problem;
however, for now, let's just add the specific model which was tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: matson <lists-matsonpa@luxsci.me>
References: http://lkml.kernel.org/g/201401211912.s0LJCk7F015058@rs103.luxsci.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efb9e0f4f43780f0ae0c6428d66bd03e805c7539 upstream.
Without the patch the kernel generates the following error.
ata11.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata11.15: Port Multiplier vendor mismatch '0x197b' != '0x123'
ata11.15: PMP revalidation failed (errno=-19)
ata11.15: failed to recover PMP after 5 tries, giving up
This patch helps to bypass this error and the device becomes
functional.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: <linux-ide@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26e61e8939b1fe8729572dabe9a9e97d930dd4f6 upstream.
Vince "Super Tester" Weaver reported a new round of syscall fuzzing (Trinity) failures,
with perf WARN_ON()s triggering. He also provided traces of the failures.
This is I think the relevant bit:
> pec_1076_warn-2804 [000] d... 147.926153: x86_pmu_disable: x86_pmu_disable
> pec_1076_warn-2804 [000] d... 147.926153: x86_pmu_state: Events: {
> pec_1076_warn-2804 [000] d... 147.926156: x86_pmu_state: 0: state: .R config: ffffffffffffffff ( (null))
> pec_1076_warn-2804 [000] d... 147.926158: x86_pmu_state: 33: state: AR config: 0 (ffff88011ac99800)
> pec_1076_warn-2804 [000] d... 147.926159: x86_pmu_state: }
> pec_1076_warn-2804 [000] d... 147.926160: x86_pmu_state: n_events: 1, n_added: 0, n_txn: 1
> pec_1076_warn-2804 [000] d... 147.926161: x86_pmu_state: Assignment: {
> pec_1076_warn-2804 [000] d... 147.926162: x86_pmu_state: 0->33 tag: 1 config: 0 (ffff88011ac99800)
> pec_1076_warn-2804 [000] d... 147.926163: x86_pmu_state: }
> pec_1076_warn-2804 [000] d... 147.926166: collect_events: Adding event: 1 (ffff880119ec8800)
So we add the insn:p event (fd[23]).
At this point we should have:
n_events = 2, n_added = 1, n_txn = 1
> pec_1076_warn-2804 [000] d... 147.926170: collect_events: Adding event: 0 (ffff8800c9e01800)
> pec_1076_warn-2804 [000] d... 147.926172: collect_events: Adding event: 4 (ffff8800cbab2c00)
We try and add the {BP,cycles,br_insn} group (fd[3], fd[4], fd[15]).
These events are 0:cycles and 4:br_insn, the BP event isn't x86_pmu so
that's not visible.
group_sched_in()
pmu->start_txn() /* nop - BP pmu */
event_sched_in()
event->pmu->add()
So here we should end up with:
0: n_events = 3, n_added = 2, n_txn = 2
4: n_events = 4, n_added = 3, n_txn = 3
But seeing the below state on x86_pmu_enable(), the must have failed,
because the 0 and 4 events aren't there anymore.
Looking at group_sched_in(), since the BP is the leader, its
event_sched_in() must have succeeded, for otherwise we would not have
seen the sibling adds.
But since neither 0 or 4 are in the below state; their event_sched_in()
must have failed; but I don't see why, the complete state: 0,0,1:p,4
fits perfectly fine on a core2.
However, since we try and schedule 4 it means the 0 event must have
succeeded! Therefore the 4 event must have failed, its failure will
have put group_sched_in() into the fail path, which will call:
event_sched_out()
event->pmu->del()
on 0 and the BP event.
Now x86_pmu_del() will reduce n_events; but it will not reduce n_added;
giving what we see below:
n_event = 2, n_added = 2, n_txn = 2
> pec_1076_warn-2804 [000] d... 147.926177: x86_pmu_enable: x86_pmu_enable
> pec_1076_warn-2804 [000] d... 147.926177: x86_pmu_state: Events: {
> pec_1076_warn-2804 [000] d... 147.926179: x86_pmu_state: 0: state: .R config: ffffffffffffffff ( (null))
> pec_1076_warn-2804 [000] d... 147.926181: x86_pmu_state: 33: state: AR config: 0 (ffff88011ac99800)
> pec_1076_warn-2804 [000] d... 147.926182: x86_pmu_state: }
> pec_1076_warn-2804 [000] d... 147.926184: x86_pmu_state: n_events: 2, n_added: 2, n_txn: 2
> pec_1076_warn-2804 [000] d... 147.926184: x86_pmu_state: Assignment: {
> pec_1076_warn-2804 [000] d... 147.926186: x86_pmu_state: 0->33 tag: 1 config: 0 (ffff88011ac99800)
> pec_1076_warn-2804 [000] d... 147.926188: x86_pmu_state: 1->0 tag: 1 config: 1 (ffff880119ec8800)
> pec_1076_warn-2804 [000] d... 147.926188: x86_pmu_state: }
> pec_1076_warn-2804 [000] d... 147.926190: x86_pmu_enable: S0: hwc->idx: 33, hwc->last_cpu: 0, hwc->last_tag: 1 hwc->state: 0
So the problem is that x86_pmu_del(), when called from a
group_sched_in() that fails (for whatever reason), and without x86_pmu
TXN support (because the leader is !x86_pmu), will corrupt the n_added
state.
Reported-and-Tested-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Dave Jones <davej@redhat.com>
Link: http://lkml.kernel.org/r/20140221150312.GF3104@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5295bd8ea8a65dc5eac608b151386314cb978f1 upstream.
In copy_oldmem_page, the current check using max_pfn and min_low_pfn to
decide if the page is backed or not, is not valid when the memory layout is
not continuous.
This happens when running as a QEMU/KVM guest, where RTAS is mapped higher
in the memory. In that case max_pfn points to the end of RTAS, and a hole
between the end of the kdump kernel and RTAS is not backed by PTEs. As a
consequence, the kdump kernel is crashing in copy_oldmem_page when accessing
in a direct way the pages in that hole.
This fix relies on the memblock's service memblock_is_region_memory to
check if the read page is part or not of the directly accessible memory.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06ea0bfe6e6043cb56a78935a19f6f8ebc636226 upstream.
When a send failure occurs due to the socket being out of buffer space,
we call xs_nospace() in order to have the RPC task wait until the
socket has drained enough to make it worth while trying again.
The current patch fixes a race in which the socket is drained before
we get round to setting up the machinery in xs_nospace(), and which
is reported to cause hangs.
Link: http://lkml.kernel.org/r/20140210170315.33dfc621@notabene.brown
Fixes: a9a6b52ee1ba (SUNRPC: Don't start the retransmission timer...)
Reported-by: Neil Brown <neilb@suse.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 548da08fc1e245faf9b0d7c41ecd8e07984fc332 upstream.
The codec->control_data contains a pointer to the device's regmap struct. But
wm8994_bulk_write() expects a pointer to the parent wm8998 device.
The issue was introduced in commit d9a7666f ("ASoC: Remove ASoC-specific
WM8994 I/O code").
Fixes: d9a7666f ("ASoC: Remove ASoC-specific WM8994 I/O code")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 025c3fa9256d4c54506b7a29dc3befac54f5c68d upstream.
Preset EQ enum of sta32x codec driver declares too many number of
items and it may lead to the access over the actual array size.
Use SOC_ENUM_SINGLE_DECL() helper and it's automatically fixed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3619b288b621e63f66908045f48495869a996a6 upstream.
There is a typo in the Limiter2 Release Rate control, a wrong enum for
Limiter1 is assigned. It must point to Limiter2.
Spotted by a compile warning:
In file included from sound/soc/codecs/sta32x.c:34:0:
sound/soc/codecs/sta32x.c:223:29: warning: ‘sta32x_limiter2_release_rate_enum’ defined but not used [-Wunused-variable]
static SOC_ENUM_SINGLE_DECL(sta32x_limiter2_release_rate_enum,
^
include/sound/soc.h:275:18: note: in definition of macro ‘SOC_ENUM_DOUBLE_DECL’
struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/codecs/sta32x.c:223:8: note: in expansion of macro ‘SOC_ENUM_SINGLE_DECL’
static SOC_ENUM_SINGLE_DECL(sta32x_limiter2_release_rate_enum,
^
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a6c0a58dc824523966f212c76322d47c5b0e6fe upstream.
wm8770 codec driver defines ain_enum with a wrong number of items.
Use SOC_ENUM_DOUBLE_DECL() macro and it's automatically fixed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 624aef494f86ed0c58056361c06347ad62b26806 upstream.
When the driver tries to access Function Unit 10, the KEF X300A
speakers' firmware apparently locks up, making even PCM streaming
impossible. Work around this by ignoring this FU.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fe6cc55f3a9a053482a76f5a6b2257cee51b4663 upstream.
[ use zero netdev_feature mask to avoid backport of
netif_skb_dev_features function ]
Marcelo Ricardo Leitner reported problems when the forwarding link path
has a lower mtu than the incoming one if the inbound interface supports GRO.
Given:
Host <mtu1500> R1 <mtu1200> R2
Host sends tcp stream which is routed via R1 and R2. R1 performs GRO.
In this case, the kernel will fail to send ICMP fragmentation needed
messages (or pkt too big for ipv6), as GSO packets currently bypass dstmtu
checks in forward path. Instead, Linux tries to send out packets exceeding
the mtu.
When locking route MTU on Host (i.e., no ipv4 DF bit set), R1 does
not fragment the packets when forwarding, and again tries to send out
packets exceeding R1-R2 link mtu.
This alters the forwarding dstmtu checks to take the individual gso
segment lengths into account.
For ipv6, we send out pkt too big error for gso if the individual
segments are too big.
For ipv4, we either send icmp fragmentation needed, or, if the DF bit
is not set, perform software segmentation and let the output path
create fragments when the packet is leaving the machine.
It is not 100% correct as the error message will contain the headers of
the GRO skb instead of the original/segmented one, but it seems to
work fine in my (limited) tests.
Eric Dumazet suggested to simply shrink mss via ->gso_size to avoid
sofware segmentation.
However it turns out that skb_segment() assumes skb nr_frags is related
to mss size so we would BUG there. I don't want to mess with it considering
Herbert and Eric disagree on what the correct behavior should be.
Hannes Frederic Sowa notes that when we would shrink gso_size
skb_segment would then also need to deal with the case where
SKB_MAX_FRAGS would be exceeded.
This uses sofware segmentation in the forward path when we hit ipv4
non-DF packets and the outgoing link mtu is too small. Its not perfect,
but given the lack of bug reports wrt. GRO fwd being broken this is a
rare case anyway. Also its not like this could not be improved later
once the dust settles.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de960aa9ab4decc3304959f69533eef64d05d8e8 upstream.
[ no skb_gso_seglen helper in 3.4, leave tbf alone ]
This moves part of Eric Dumazets skb_gso_seglen helper from tbf sched to
skbuff core so it may be reused by upcoming ip forwarding path patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ffd5939381c609056b33b7585fb05a77b4c695f3 ]
SCTP's sctp_connectx() abi breaks for 64bit kernels compiled with 32bit
emulation (e.g. ia32 emulation or x86_x32). Due to internal usage of
'struct sctp_getaddrs_old' which includes a struct sockaddr pointer,
sizeof(param) check will always fail in kernel as the structure in
64bit kernel space is 4bytes larger than for user binaries compiled
in 32bit mode. Thus, applications making use of sctp_connectx() won't
be able to run under such circumstances.
Introduce a compat interface in the kernel to deal with such
situations by using a 'struct compat_sctp_getaddrs_old' structure
where user data is copied into it, and then sucessively transformed
into a 'struct sctp_getaddrs_old' structure with the help of
compat_ptr(). That fixes sctp_connectx() abi without any changes
needed in user space, and lets the SCTP test suite pass when compiled
in 32bit and run on 64bit kernels.
Fixes: f9c67811ebc0 ("sctp: Fix regression introduced by new sctp_connectx api")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit eb85569fe2d06c2fbf4de7b66c263ca095b397aa ]
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 163c8ff30dbe473abfbb24a7eac5536c87f3baa9 ]
aggregator_identifier is used to assign unique aggregator identifiers
to aggregators of a bond during device enslaving.
aggregator_identifier is currently a global variable that is zeroed in
bond_3ad_initialize().
This sequence will lead to duplicate aggregator identifiers for eth1 and eth3:
create bond0
change bond0 mode to 802.3ad
enslave eth0 to bond0 //eth0 gets agg id 1
enslave eth1 to bond0 //eth1 gets agg id 2
create bond1
change bond1 mode to 802.3ad
enslave eth2 to bond1 //aggregator_identifier is reset to 0
//eth2 gets agg id 1
enslave eth3 to bond0 //eth3 gets agg id 2
Fix this by making aggregator_identifier private to the bond.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c6993dfd7db9b0c6b7ca7503a56fda9236a4710f ]
Quoting David Vrabel -
"5780 cards cannot have jumbo frames and TSO enabled together. When
jumbo frames are enabled by setting the MTU, the TSO feature must be
cleared. This is done indirectly by calling netdev_update_features()
which will call tg3_fix_features() to actually clear the flags.
netdev_update_features() will also trigger a new netlink message for the
feature change event which will result in a call to tg3_get_stats64()
which deadlocks on the tg3 lock."
tg3_set_mtu() does not need to be under the tg3 lock since converting
the flags to use set_bit(). Move it out to after tg3_netif_stop().
Reported-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 946c032e5a53992ea45e062ecb08670ba39b99e3 ]
ip rules with iif/oif references do not update:
(detach/attach) across interface renames.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
CC: Willem de Bruijn <willemb@google.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Chris Davis <chrismd@google.com>
CC: Carlo Contavalli <ccontavalli@google.com>
Google-Bug-Id: 12936021
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 upstream.
rtl8192ce is disabling for too long the local interrupts during hw initiatialisation when performing scans
The observable symptoms in dmesg can be:
- underruns from ALSA playback
- clock freezes (tstamps do not change for several dmesg entries until irqs are finaly reenabled):
[ 250.817669] rtlwifi:rtl_op_config():<0-0-0> 0x100
[ 250.817685] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-1-0> IPS Set eRf nic enable
[ 250.817732] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817796] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817910] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818024] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818139] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818253] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818367] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:98053f15:10
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtl8192c_common:rtl92c_download_fw():<0-1-0> Firmware Version(49), Signature(0x88c1),Size(32)
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> The SECR-value cc
[ 250.818472] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-1-0> Schedule TxPowerTracking direct call!!
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> rtl92c_dm_txpower_tracking_callback_thermalmeter
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial pathA ele_d reg0xc80 = 0x40000000, ofdm_index=0xc
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial reg0xa24 = 0x90e1317, cck_index=0xc, ch14 0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf delta 0x1 delta_lck 0x0 delta_iqk 0x0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> <===
[ 250.818472] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-1-0> pMgntInfo->txpower_tracking = 1
[ 250.818472] rtl8192ce:rtl92ce_led_control():<0-1-0> ledaction 3
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtlwifi:rtl_ips_nic_on():<0-1-0> before spin_unlock_irqrestore
[ 251.154656] PCM: Lost interrupts? [Q]-0 (stream=0, delta=15903, new_hw_ptr=293408, old_hw_ptr=277505)
The exact code flow that causes that is:
1. wpa_supplicant send a start_scan request to the nl80211 driver
2. mac80211 module call rtl_op_config with IEEE80211_CONF_CHANGE_IDLE
3. rtl_ips_nic_on is called which disable local irqs
4. rtl92c_phy_set_rf_power_state() is called
5. rtl_ps_enable_nic() is called and hw_init()is executed and then the interrupts on the device are enabled
A good solution could be to refactor the code to avoid calling rtl92ce_hw_init() with the irqs disabled
but a quick and dirty solution that has proven to work is
to reenable the irqs during the function rtl92ce_hw_init().
I think that it is safe doing so since the device interrupt will only be enabled after the init function succeed.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e8c5e56b307271c2dab6f8bfd1d8a3822ca2390 upstream.
rtl_ps_enable_nic() is called from loops that will loop until this function returns true or a
maximum number of retries is performed.
hw_init() returns non-zero on error. In that situation return false to
restore the original design intent to retry hw init when it fails.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b6213e413a4e0c66548153516b074df14f9d08e0 upstream.
This patch fixes regression caused by commit a16dad77634 "MIPS: Fix
potencial corruption". That commit fixes one corruption scenario in
cost of adding another one, which actually start to cause crashes
on Yeeloong laptop when rtl8187 driver is used.
For correct DMA read operation on machines without DMA coherence, kernel
have to invalidate cache, such it will refill later with new data that
device wrote to memory, when that data is needed to process. We can only
invalidate full cache line. Hence when cache line includes both dma
buffer and some other data (written in cache, but not yet in main
memory), the other data can not hit memory due to invalidation. That
happen on rtl8187 where struct rtl8187_priv fields are located just
before and after small buffers that are passed to USB layer and DMA
is performed on them.
To fix the problem we align buffers and reserve space after them to make
them match cache line.
This patch does not resolve all possible MIPS problems entirely, for
that we have to assure that we always map cache aligned buffers for DMA,
what can be complex or even not possible. But patch fixes visible and
reproducible regression and seems other possible corruptions do not
happen in practice, since Yeeloong laptop works stable without rtl8187
driver.
Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=54391
Reported-by: Petr Pisar <petr.pisar@atlas.cz>
Bisected-by: Tom Li <biergaizi2009@gmail.com>
Reported-and-tested-by: Tom Li <biergaizi2009@gmail.com>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.next>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d81de8e8667da7135d3a32a964087c0faf5483f upstream.
It's possible for userland to pass down an iovec via writev() that has a
bogus user pointer in it. If that happens and we're doing an uncached
write, then we can end up getting less bytes than we expect from the
call to iov_iter_copy_from_user. This is CVE-2014-0069
cifs_iovec_write isn't set up to handle that situation however. It'll
blindly keep chugging through the page array and not filling those pages
with anything useful. Worse yet, we'll later end up with a negative
number in wdata->tailsz, which will confuse the sending routines and
cause an oops at the very least.
Fix this by having the copy phase of cifs_iovec_write stop copying data
in this situation and send the last write as a short one. At the same
time, we want to avoid sending a zero-length write to the server, so
break out of the loop and set rc to -EFAULT if that happens. This also
allows us to handle the case where no address in the iovec is valid.
[Note: Marking this for stable on v3.4+ kernels, but kernels as old as
v2.6.38 may have a similar problem and may need similar fix]
Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d80390cfc9434d5aa4fb9e5f9768a66b30cb8a6 upstream.
For avr32 cross compiler, do not define '__linux__' internally, so it
will cause issue with allmodconfig.
The related error:
CC [M] fs/coda/psdev.o
In file included from include/linux/coda.h:64,
from fs/coda/psdev.c:45:
include/uapi/linux/coda.h:221: error: expected specifier-qualifier-list before 'u_quad_t'
The related toolchain version (which only download, not re-compile):
[root@gchen linux-next]# /upstream/toolchain/download/avr32-gnu-toolchain-linux_x86/bin/avr32-gcc -v
Using built-in specs.
Target: avr32
Configured with: /data2/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/src/gcc/configure --target=avr32 --host=i686-pc-linux-gnu --build=x86_64-pc-linux-gnu --prefix=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --enable-languages=c,c++ --disable-nls --disable-libssp --disable-libstdcxx-pch --with-dwarf2 --enable-version-specific-runtime-libs --disable-shared --enable-doc --with-mpfr-lib=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86/lib --with-mpfr-include=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86/include --with-gmp=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --with-mpc=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --enable-__cxa_atexit --disable-shared --with-newlib --with-pkgversion=AVR_32_bit_GNU_Toolchain_3.4.2_435 --with-bugurl=http://www
.atmel.com/avr
Thread model: single
gcc version 4.4.7 (AVR_32_bit_GNU_Toolchain_3.4.2_435)
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5745d6a41a4f4aec29e2ccd591c6fb09ed73a955 upstream.
Causing this:
In file included from arch/avr32/boards/mimc200/fram.c:13:
include/linux/miscdevice.h:51: error: field 'list' has incomplete type
include/linux/miscdevice.h:55: error: expected specifier-qualifier-list before 'mode_t'
arch/avr32/boards/mimc200/fram.c:42: error: 'THIS_MODULE' undeclared here (not in a function)
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 39544ac9df20f73e49fc6b9ac19ff533388c82c0 upstream.
Add DSB after icache flush to complete the cache maintenance operation.
Signed-off-by: Vinayak Kale <vkale@apm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bae0ca2bc550d1ec6a118fb8f2696f18c4da3d8e upstream.
During __v{6,7}_setup, we invalidate the TLBs since we are about to
enable the MMU on return to head.S. Unfortunately, without a subsequent
dsb instruction, the invalidation is not guaranteed to have completed by
the time we write to the sctlr, potentially exposing us to junk/stale
translations cached in the TLB.
This patch reworks the init functions so that the dsb used to ensure
completion of cache/predictor maintenance is also used to ensure
completion of the TLB invalidation.
Reported-by: Albin Tonnerre <Albin.Tonnerre@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19ea80603715d473600cd993b9987bc97d042e02 upstream.
If the i_crtime field is not present in the inode, don't leave the
field uninitialized.
Fixes: ef7f38359 ("ext4: Add nanosecond timestamps")
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d2660d0c9c2f296837078c189b68a47f6b2e3b5 upstream.
The set_flexbg_block_bitmap() function assumed that the number of
blocks in a blockgroup was sb->blocksize * 8, which is normally true,
but not always! Use EXT4_BLOCKS_PER_GROUP(sb) instead, to fix block
bitmap corruption after:
mke2fs -t ext4 -g 3072 -i 4096 /dev/vdd 1G
mount -t ext4 /dev/vdd /vdd
resize2fs /dev/vdd 8G
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Jon Bernard <jbernard@tuxion.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 23301410972330c0ae9a8afc379ba2005e249cc6 upstream.
If an ext4 file system is created by some tool other than mke2fs
(perhaps by someone who has a pathalogical fear of the GPL) that
doesn't set one or the other of the EXT2_FLAGS_{UN}SIGNED_HASH flags,
and that file system is then mounted read-only, don't try to modify
the s_flags field. Otherwise, if dm_verity is in use, the superblock
will change, causing an dm_verity failure.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 2c45aada341121438affc4cb8d5b4cfaa2813d3d upstream.
In allmodconfig builds for sparc and any other arch which does
not set CONFIG_SPARSE_IRQ, the following will be seen at modpost:
CC [M] lib/cpu-notifier-error-inject.o
CC [M] lib/pm-notifier-error-inject.o
ERROR: "irq_to_desc" [drivers/gpio/gpio-mcp23s08.ko] undefined!
make[2]: *** [__modpost] Error 1
This happens because commit 3911ff30f5 ("genirq: export
handle_edge_irq() and irq_to_desc()") added one export for it, but
there were actually two instances of it, in an if/else clause for
CONFIG_SPARSE_IRQ. Add the second one.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Link: http://lkml.kernel.org/r/1392057610-11514-1-git-send-email-paul.gortmaker@windriver.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d651aa1d68a2f0a7ee65697b04c6a92f8c0a12f2 upstream.
Each sub-buffer (buffer page) has a full 64 bit timestamp. The events on
that page use a 27 bit delta against that timestamp in order to save on
bits written to the ring buffer. If the time between events is larger than
what the 27 bits can hold, a "time extend" event is added to hold the
entire 64 bit timestamp again and the events after that hold a delta from
that timestamp.
As a "time extend" is always paired with an event, it is logical to just
allocate the event with the time extend, to make things a bit more efficient.
Unfortunately, when the pairing code was written, it removed the "delta = 0"
from the first commit on a page, causing the events on the page to be
slightly skewed.
Fixes: 69d1b839f7ee "ring-buffer: Bind time extend and data events together"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac323d8d807060f7c95a685a9fe861e7b6300993 upstream.
Fix NULL pointer dereference of "chip->pdata" if platform_data was not
supplied to the driver.
The driver during probe stored the pointer to the platform_data:
chip->pdata = client->dev.platform_data;
Later it was dereferenced in max17040_get_online() and
max17040_get_status().
If platform_data was not supplied, the NULL pointer exception would
happen:
[ 6.626094] Unable to handle kernel of a at virtual address 00000000
[ 6.628557] pgd = c0004000
[ 6.632868] [00000000] *pgd=66262564
[ 6.634636] Unable to handle kernel paging request at virtual address e6262000
[ 6.642014] pgd = de468000
[ 6.644700] [e6262000] *pgd=00000000
[ 6.648265] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 6.653552] Modules linked in:
[ 6.656598] CPU: 0 PID: 31 Comm: kworker/0:1 Not tainted 3.10.14-02717-gc58b4b4 #505
[ 6.664334] Workqueue: events max17040_work
[ 6.668488] task: dfa11b80 ti: df9f6000 task.ti: df9f6000
[ 6.673873] PC is at show_pte+0x80/0xb8
[ 6.677687] LR is at show_pte+0x3c/0xb8
[ 6.681503] pc : [<c001b7b8>] lr : [<c001b774>] psr: 600f0113
[ 6.681503] sp : df9f7d58 ip : 600f0113 fp : 00000009
[ 6.692965] r10: 00000000 r9 : 00000000 r8 : dfa11b80
[ 6.698171] r7 : df9f7ea0 r6 : e6262000 r5 : 00000000 r4 : 00000000
[ 6.704680] r3 : 00000000 r2 : e6262000 r1 : 600f0193 r0 : c05b3750
[ 6.711194] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 6.718485] Control: 10c53c7d Table: 5e46806a DAC: 00000015
[ 6.724218] Process kworker/0:1 (pid: 31, stack limit = 0xdf9f6238)
[ 6.730465] Stack: (0xdf9f7d58 to 0xdf9f8000)
[ 6.914325] [<c001b7b8>] (show_pte+0x80/0xb8) from [<c047107c>] (__do_kernel_fault.part.9+0x44/0x74)
[ 6.923425] [<c047107c>] (__do_kernel_fault.part.9+0x44/0x74) from [<c001bb7c>] (do_page_fault+0x2c4/0x360)
[ 6.933144] [<c001bb7c>] (do_page_fault+0x2c4/0x360) from [<c0008400>] (do_DataAbort+0x34/0x9c)
[ 6.941825] [<c0008400>] (do_DataAbort+0x34/0x9c) from [<c000e5d8>] (__dabt_svc+0x38/0x60)
[ 6.950058] Exception stack(0xdf9f7ea0 to 0xdf9f7ee8)
[ 6.955099] 7ea0: df0c1790 00000000 00000002 00000000 df0c1794 df0c1790 df0c1790 00000042
[ 6.963271] 7ec0: df0c1794 00000001 00000000 00000009 00000000 df9f7ee8 c0306268 c0306270
[ 6.971419] 7ee0: a00f0113 ffffffff
[ 6.974902] [<c000e5d8>] (__dabt_svc+0x38/0x60) from [<c0306270>] (max17040_work+0x8c/0x144)
[ 6.983317] [<c0306270>] (max17040_work+0x8c/0x144) from [<c003f364>] (process_one_work+0x138/0x440)
[ 6.992429] [<c003f364>] (process_one_work+0x138/0x440) from [<c003fa64>] (worker_thread+0x134/0x3b8)
[ 7.001628] [<c003fa64>] (worker_thread+0x134/0x3b8) from [<c00454bc>] (kthread+0xa4/0xb0)
[ 7.009875] [<c00454bc>] (kthread+0xa4/0xb0) from [<c000eb28>] (ret_from_fork+0x14/0x2c)
[ 7.017943] Code: e1a03005 e2422480 e0826104 e59f002c (e7922104)
[ 7.024017] ---[ end trace 73bc7006b9cc5c79 ]---
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: c6f4a42de60b981dd210de01cd3e575835e3158e
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 80d767d770fd9c697e434fd080c2db7b5c60c6dd upstream.
When compiling for the IA-64 ski emulator, HZ is set to 32 because the
emulation is slow and we don't want to waste too many cycles processing
timers. Alpha also has an option to set HZ to 32.
This causes integer underflow in
kernel/time/jiffies.c:
kernel/time/jiffies.c:66:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
.mult = NSEC_PER_JIFFY << JIFFIES_SHIFT, /* details above */
^
This patch reduces the JIFFIES_SHIFT value to avoid the overflow.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1401241639100.23871@file01.intranet.prod.int.rdu2.redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 789b5e0315284463617e106baad360cb9e8db3ac upstream.
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Interestingly, the raid5 code can actually prevent double initialization and
hence can use the following simplified form of callback registration:
register_cpu_notifier(&foobar_cpu_notifier);
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
put_online_cpus();
A hotplug operation that occurs between registering the notifier and calling
get_online_cpus(), won't disrupt anything, because the code takes care to
perform the memory allocations only once.
So reorganize the code in raid5 this way to fix the deadlock with callback
registration.
Cc: linux-raid@vger.kernel.org
Fixes: 36d1c6476be51101778882897b315bd928c8c7b5
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
[Srivatsa: Fixed the unregister_cpu_notifier() deadlock, added the
free_scratch_buffer() helper to condense code further and wrote the changelog.]
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aac5c4226e7136c331ed384c25d5560204da10a0 upstream.
If kvm_io_bus_register_dev() fails then it returns success but it should
return an error code.
I also did a little cleanup like removing an impossible NULL test.
Fixes: 2b3c246a682c ('KVM: Make coalesced mmio use a device per zone')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2f75e12c4457a9b3d042c0a0d748fa198dc2ffaf upstream.
Research has shown that commit a77fcf895046 ("IB/qib: Use a single
txselect module parameter for serdes tuning") missed a key serdes init
sequence.
This patch add that sequence.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c8123f8c9cb517403b51aa41c3c46ff5e10b2c17 upstream.
When mkfs issues a full device discard and the device only
supports discards of a smallish size, we can loop in
blkdev_issue_discard() for a long time. If preempt isn't enabled,
this can turn into a softlock situation and the kernel will
start complaining.
Add an explicit cond_resched() at the end of the loop to avoid
that.
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
