| Age | Commit message (Collapse) | Author |
|---|
|
When watching the interrupts through /proc/interrupts,
the name of the interrupts are blank or garbage. The
reason is the pointer passed for devname during irq
registration is stack and so it get changed after
dma registration completes.
Allocate the pointer as part of dma channel and pass
this pointer as the devname for irq registration to
avoid change of name.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Sometimes memory-to-memory test is failed, that's why we need to choose minimum
data portion between source and destination limits together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Some controllers have the reduced functionality where the LLP multi block
transfers are not supported. This patch introduces a support of such
controllers. In case of memory copy or scatter-gather lists it emulates LLP
transfers via bunch of the regular single block ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Not all of the controllers support the 64 bit data width. Make it configurable
via platform data. The driver will try to get a value from the component
parameters, otherwise it will use the platform data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
The maximum block size is a configurable parameter for the chip. So, driver
will try to get it from the encoded component parameters. Otherwise it will
come from the platform data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
In case the controller has the encoded parameters feature enabled the driver
will use it to get the number of channels. In the future it will be used for
the other important parameters as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
There is a block of the registers that are optional. However, if enabled they
contain useful information about the controller hardware configuration. We will
use this piece of data to autoconfigure the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Since 0 is not considered as error at dmaengine level, return ENOMEM
from pl330_alloc_chan_resources in case of failure.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
The driver's runtime_suspend/resume functions just disable/enable
the clock which is already being managed at AMBA bus level
runtime_suspend/resume functions.
Hence, remove the driver's runtime_suspend/resume functions.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Tested-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
The controller clock is being enabled/disabled in AMBA bus
infrastructre in probe/remove functions. Hence, its not required
at driver level probe/remove.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Tested-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Using kmem_cache_zalloc() instead of kmem_cache_alloc() and memset().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
DMA clients pdma0 and pdma1 are internal to the SoC and are used only
by dedicated peripherals. Since they cannot be used for generic
purpose, their capability should be set as DMA_PRIVATE.
CC: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
DMA clients pdma0 and pdma1 are internal to the SoC and are used only
by dedicated peripherals. Since they cannot be used for generic
purpose, their capability should be set as DMA_PRIVATE.
CC: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Using list_move_tail() instead of list_del() + list_add_tail().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
In case of a large SPI flash, the amount of DMA descriptors
available to the DMA driver is not large enough anymore. For
example 8MB SPI flash now needs 129 descriptors to be transfered
in one long read. There are currently 53 descriptors available in
one PAGE_SIZE-big block. Enlarge the allocated descriptor area to
four PAGE_SIZE blocks to fulfill such requirements.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dan Williams <djbw@fb.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
There is slave_id field in the generic slave config structure that is dedicated
for the uniq slave number. In our case we have the request lines wired to the
certain hardware. Therefore the number of the request line is uniq and could be
used as slave_id. It allows us in some cases to drop out the usage of the
custom slave config structure.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
1. virtual channel vs. physical channel
Virtual channel is managed by dmaengine
Physical channel handling resource, such as irq
Physical channel is alloced dynamically as descending priority,
freed immediately when irq done.
The availble highest priority physically channel will alwayes be alloced
Issue pending list -> alloc highest dma physically channel available -> dma done -> free physically channel
2. list: running list & pending list
submit: desc list -> pending list
issue_pending_list: if (IDLE) pending list -> running list; free pending list (RUN)
irq: free running list (IDLE)
check pendlist -> pending list -> running list; free pending list (RUN)
3. irq:
Each list generate one irq, calling callback
One list may contain several desc chain, in such case, make sure only the last desc list generate irq.
4. async
Submit will add desc chain to pending list, which can be multi-called
If multi desc chain is submitted, only the last desc would generate irq -> call back
If IDLE, issue_pending_list start pending_list, transforming pendlist to running list
If RUN, irq will start pending list
5. test
5.1 pxa3xx_nand on pxa910
5.2 insmod dmatest.ko (threads_per_chan=y)
By default drivers/dma/dmatest.c test every channel and test memcpy with 1 threads per channel
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Removes use of the DaVinci EDMA private DMA API and replaces
it with use of the DMA engine API.
Signed-off-by: Matt Porter <mporter@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Removes use of the DaVinci EDMA private DMA API and replaces
it with use of the DMA engine API.
Signed-off-by: Matt Porter <mporter@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Add a DMA engine driver for the TI EDMA controller. This driver
is implemented as a wrapper around the existing DaVinci private
DMA implementation. This approach allows for incremental conversion
of each peripheral driver to the DMA engine API. The EDMA driver
supports slave transfers but does not yet support cyclic transfers.
Signed-off-by: Matt Porter <mporter@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@db.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Fixup some errorhandling for clocks during probe and make sure
to use clk_prepare as well as clk_enable.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Fix some problems with the use of devm_ functions.
devm_kzalloc: devm_kfree is not needed
devm_ioremap: iounmap should not be used, no free is needed
devm_request_irq: the devm_free_irq is followed by irq_dispose_mapping. I
don't know if it is safe to move the freeing of the irq in this case, so I
have just un-devm'd this function, since the implicit freeing is never
taken advantage of.
In the original code failure of of_address_to_resource jumped to free_mem,
but should have jumped to irq_dispose, since irq_of_parse_and_map has
completed at this point.
In the original code unmap_mem was after irq_dispose, but it should have
been before, again since irq_of_parse_and_map has completed at this point.
One of these problems was found using the following semantic match:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
*x = devm_ioremap(...)
...
iounmap(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
|
|
|
|
|
|
Pull OLPC platform updates from Andres Salomon:
"These move the OLPC Embedded Controller driver out of
arch/x86/platform and into drivers/platform/olpc.
OLPC machines are now ARM-based (which means lots of x86 and ARM
changes), but are typically pretty self-contained.. so it makes more
sense to go through a separate OLPC tree after getting the appropriate
review/ACKs."
* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
x86: OLPC: move s/r-related EC cmds to EC driver
Platform: OLPC: move global variables into priv struct
Platform: OLPC: move debugfs support from x86 EC driver
x86: OLPC: switch over to using new EC driver on x86
Platform: OLPC: add a suspended flag to the EC driver
Platform: OLPC: turn EC driver into a platform_driver
Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
drivers: OLPC: update various drivers to include olpc-ec.h
Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver
|
|
Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
"This contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the
branch into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: Kirkwood: Replace mrvl with marvell
ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
ARM: Kirkwood: Describe Dreamplug LEDs in DT.
ARM: Kirkwood: Describe iConnects LEDs in DT.
ARM: Kirkwood: Describe iConnects temperature sensor in DT.
ARM: Kirkwood: Describe IB62x0 LEDs in DT.
ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
ARM: Kirkwood: Use DT to configure SATA device.
ARM: kirkwood: use devicetree for SPI on dreamplug
ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
ARM: Kirkwood: Add basic device tree support for QNAP TS219.
ATA: sata_mv: Add device tree support
ARM: Orion: DTify the watchdog timer.
ARM: Orion: Add arch support needed for I2C via DT.
ARM: kirkwood: use devicetree for orion-spi
...
Conflicts:
drivers/watchdog/orion_wdt.c
|
|
Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
"Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
but didn't go in because the pull request ended up rejected. So it
just got merged, and we got this staged branch that enables the
coupled cpuidle code on OMAP.
With a stable git workflow from the other maintainer we could have
staged this earlier, but that wasn't the case so we have had to merge
it late.
The alternative is to hold it off until 3.7 but given that the code is
well-isolated to OMAP and they are eager to see it go in, I didn't
push back hard in that direction."
* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP4: CPUidle: Open broadcast clock-event device.
ARM: OMAP4: CPUidle: add synchronization for coupled idle states
ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for merge window fallout, and a bugfix for timer resume on
PRIMA2."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mmp: add missing irqs.h
arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
ARM: mxc: Include missing irqs.h header
|
|
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
sh: explicitly include sh_dma.h in setup-sh7722.c
sh: ecovec: care CN5 VBUS if USB host mode
sh: sh7724: fixup renesas_usbhs clock settings
sh: intc: initial irqdomain support.
sh: pfc: Fix up init ordering mess.
serial: sh-sci: fix compilation breakage, when DMA is enabled
dmaengine: shdma: restore partial transfer calculation
sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
sh: Fix up recursive fault in oops with unset TTB.
sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
sh: select the fixed regulator driver on several boards
sh: ecovec: switch MMC power control to regulators
sh: add fixed voltage regulators to se7724
sh: add fixed voltage regulators to sdk7786
sh: add fixed voltage regulators to rsk
sh: add fixed voltage regulators to migor
sh: add fixed voltage regulators to kfr2r09
sh: add fixed voltage regulators to ap325rxa
sh: add fixed voltage regulators to sh7757lcr
sh: add fixed voltage regulators to sh2007
...
|
|
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull two ceph fixes from Sage Weil:
"The first patch fixes up the old crufty open intent code to use the
atomic_open stuff properly, and the second fixes a possible null deref
and memory leak with the crypto keys."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix crypto key null deref, memory leak
ceph: simplify+fix atomic_open
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
- Fixes a bug when the lower filesystem mount options include 'acl',
but the eCryptfs mount options do not
- Cleanups in the messaging code
- Better handling of empty files in the lower filesystem to improve
usability. Failed file creations are now cleaned up and empty lower
files are converted into eCryptfs during open().
- The write-through cache changes are being reverted due to bugs that
are not easy to fix. Stability outweighs the performance
enhancements here.
- Improvement to the mount code to catch unsupported ciphers specified
in the mount options
* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: check for eCryptfs cipher support at mount
eCryptfs: Revert to a writethrough cache model
eCryptfs: Initialize empty lower files when opening them
eCryptfs: Unlink lower inode when ecryptfs_create() fails
eCryptfs: Make all miscdev functions use daemon ptr in file private_data
eCryptfs: Remove unused messaging declarations and function
eCryptfs: Copy up POSIX ACL and read-only flags from lower mount
|
|
Pull CIFS update from Steve French:
"Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.
I am holding up a few more days on merging the remainder of the
SMB2/SMB2.1 enablement although it is nearing review completion, in
order to address some review comments from Jeff Layton on a few of the
subsequent SMB2 patches, and also to debug an unrelated cifs problem
that Pavel discovered."
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Add SMB2 support for rmdir
CIFS: Move rmdir code to ops struct
CIFS: Add SMB2 support for mkdir operation
CIFS: Separate protocol specific part from mkdir
CIFS: Simplify cifs_mkdir call
|
|
Borislav Petkov reports that the new warning added in commit
88fdf75d1bb5 ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.
The call trace looks like this:
x86_64_start_kernel ->
x86_64_start_reservations ->
start_kernel ->
setup_arch ->
paging_init ->
zone_sizes_init ->
free_area_init_nodes ->
free_area_init_node
and (with the warning replaced by debug output), Borislav sees
On node 0 totalpages: 4193848
DMA zone: 64 pages used for memmap
DMA zone: 6 pages reserved
DMA zone: 3890 pages, LIFO batch:0
DMA32 zone: 16320 pages used for memmap
DMA32 zone: 798464 pages, LIFO batch:31
Normal zone: 52736 pages used for memmap
Normal zone: 3322368 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 4423680 <----
On node 1 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 8617984 <----
On node 2 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 12812288 <----
On node 3 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
so remove the bogus warning for now to avoid annoying people. Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1
Include <mach/irqs.h> to fix this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
SIRFSOC_TIMER_LATCH);
Writing values to LATCHED registers directly is useless at all.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Avoid crashing if the crypto key payload was NULL, as when it was not correctly
allocated and initialized. Also, avoid leaking it.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
|
|
The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work. Replace it with a fresh
method. In particular:
* always attempt to do an atomic open+lookup, both for the create case
and for lookups of existing files.
* fix symlink handling by returning 1 to the VFS so that we can follow
the link to its destination. This fixes a longstanding ceph bug (#2392).
Signed-off-by: Sage Weil <sage@inktank.com>
|
|
setup-sh7722.c defines several objects, whose types are defined in
sh_dma.h, so, it has to be included explicitly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Pull MIPS updates from Ralf Baechle:
"The lion share of this pull request are fixes for clk-related breakage
caused by other changes during this merge window. For some platforms
the fix was as simple as selecting HAVE_CLK, for others like the
Loongson 2 significant restructuring was required.
The remainder are changes required to get the Lantiq code to work
again."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Loongson 2: Sort out clock managment.
MIPS: Loongson 1: more clk support and add select HAVE_CLK
MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: Lantiq: Platform specific CLK fixup
MIPS: Lantiq: Add device_tree_init function
MIPS: Lantiq: Fix interface clock and PCI control register offset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger:
"This patch set contains mostly fixes and cleanups. The UML tty driver
uses now tty_port and is no longer broken like hell :-)"
* 'for-linus-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Add arch/x86/um to MAINTAINERS
um: pass siginfo to guest process
um: fix ubd_file_size for read-only files
um: pull interrupt_end() into userspace()
um: split syscall_trace(), pass pt_regs to it
um: switch UPT_SET_RETURN_VALUE and regs_return_value to pt_regs
um: set BLK_CGROUP=y in defconfig
um: remove count_lock
um: fully use tty_port
um: Remove dead code
um: remove line_ioctl()
TTY: um/line, use tty from tty_port
TTY: um/line, add tty_port
|
|
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
|
|
Pull ARM audit/signal updates from Russell King:
"ARM audit/signal handling updates from Al and Will. This improves on
the work Viro did last merge window, and sorts out some of the issues
found with that work."
* 'audit' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7475/1: sys_trace: allow all syscall arguments to be updated via ptrace
ARM: 7474/1: get rid of TIF_SYSCALL_RESTARTSYS
ARM: 7473/1: deal with handlerless restarts without leaving the kernel
ARM: 7472/1: pull all work_pending logics into C function
ARM: 7471/1: Revert "7442/1: Revert "remove unused restart trampoline""
ARM: 7470/1: Revert "7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK""
|
