| Age | Commit message (Collapse) | Author |
|---|
|
Get the sctp partial delivery point using SCTP_PARTIAL_DELIVERY_POINT
socket option should return 0 if success, not -ENOTSUPP.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't change ip_summed from CHECKSUM_PARTIAL to CHECKSUM_NONE
or CHECKSUM_UNNECESSARY because checksum in packet's headers is
not valid and will cause invalid checksum when frame is forwarded.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a missing ntohs() for bridge IPv6 multicast snooping.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Special care is taken inside sk_port_alloc to avoid overwriting
skc_node/skc_nulls_node. We should also avoid overwriting
skc_bind_node/skc_portaddr_node.
The patch fixes the following crash:
BUG: unable to handle kernel paging request at fffffffffffffff0
IP: [<ffffffff812ec6dd>] udp4_lib_lookup2+0xad/0x370
[<ffffffff812ecc22>] __udp4_lib_lookup+0x282/0x360
[<ffffffff812ed63e>] __udp4_lib_rcv+0x31e/0x700
[<ffffffff812bba45>] ? ip_local_deliver_finish+0x65/0x190
[<ffffffff812bbbf8>] ? ip_local_deliver+0x88/0xa0
[<ffffffff812eda35>] udp_rcv+0x15/0x20
[<ffffffff812bba45>] ip_local_deliver_finish+0x65/0x190
[<ffffffff812bbbf8>] ip_local_deliver+0x88/0xa0
[<ffffffff812bb2cd>] ip_rcv_finish+0x32d/0x6f0
[<ffffffff8128c14c>] ? netif_receive_skb+0x99c/0x11c0
[<ffffffff812bb94b>] ip_rcv+0x2bb/0x350
[<ffffffff8128c14c>] netif_receive_skb+0x99c/0x11c0
Signed-off-by: Leonard Crestez <lcrestez@ixiacom.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the mbox polling uses the schedule_timeout, the mbox_lock should be
a mutex and not a spin lock.
The commit f25b03a replaced udelay() with schedule_timeout() but didn't
change mbox_lock to semaphore or mutex.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I wrote this quirk awhile ago to properly setup MCP55 chips on hypertransport
busses so that interrupts reached whatever cpu happend to boot the kdump kernel.
while that works well, it was recently shown to me that a a non-hypertransport
variant of the MCP55 exists, and on those system the register that this quirk
manipulates causes hangs if you write to it. Since the quirk was only meant to
handle errors found on MCP55 chips that have a HT interface, this patch adds a
filter to make sure the chip is an HT capable before making the needed register
adjustment. This lets the broken MCP55s work with kdump while not breaking the
non-HT variants.
Resolves https://bugzilla.kernel.org/show_bug.cgi?id=23952
Tested successfully by the reporter and myself.
Cc: stable@kernel.org
Reported-by: Mathieu Bérard <mathieu@mberard.eu>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
gsm_data_alloc buffer allocation could fail and it is not being checked.
Add check for allocated buffer and return if the buffer allocation
fails.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix message length handling when building header
When the message length is greater than 127, the length field in the header
is built incorrectly. According to the spec, when the length is less than 128
the length field is a single byte formatted as: bbbbbbb1. When it is greater
than 127 then the field is two bytes of the format: bbbbbbb0 bbbbbbbb.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
bond_na_send() attempts to insert a VLAN tag in between building and
sending packets of the respective formats. If the slave does not
implement hardware VLAN tag insertion then vlan_put_tag() will mangle
the network-layer header because the Ethernet header is not present at
this point (unlike in bond_arp_send()).
Fix this by adding the tag out-of-line and relying on
dev_hard_start_xmit() to insert it inline if necessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bond_change_active_slave() may be called when a slave is added, even
if the bond has not been brought up yet. It may then attempt to send
packets, and further it may use mcast_work which is uninitialised
before the bond is brought up. Add the necessary checks for
netif_running(bond->dev).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A bond may have a mixture of slave devices with and without hardware
VLAN tag insertion capability. Therefore it always claims this
capability and performs software VLAN tag insertion if the slave does
not.
Since commit 7b9c60903714bf0a19d746b228864bad3497284e, this has
also been done by dev_hard_start_xmit(). The result is that VLAN-
tagged skbs are now double-tagged when transmitted through slave
devices without hardware VLAN tag insertion!
Remove the now-redundant logic from bond_dev_queue_xmit().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
axnet_cs:
Accton EN2328 or compatible (id: 0x01bf, 0x2328) uses Asix chip.
So it works better with axnet_cs instead of pcnet_cs.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first big packets sent to a "low-MTU" client correctly
triggers the creation of a temporary route containing the reduced MTU.
But after the temporary route has expired, new ICMP6 "packet too big"
will be sent, rt6_pmtu_discovery will find the previous EXPIRED route
check that its mtu isn't bigger then in icmp packet and do nothing
before the temporary route will not deleted by gc.
I make the simple experiment:
while :; do
time ( dd if=/dev/zero bs=10K count=1 | ssh hostname dd of=/dev/null ) || break;
done
The "time" reports real 0m0.197s if a temporary route isn't expired, but
it reports real 0m52.837s (!!!!) immediately after a temporare route has
expired.
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The returned slave is incorrect, if the net device under check is not
charged yet by the master.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For huge page support with base page size of 16K or 32K, we have to
increase the MAX_ORDER so that huge pages can be allocated.
[Ralf: I don't think a user should have to configure obscure constants like
this but for the time being this will have to suffice.]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1685/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
I am about to commit:
http://sourceware.org/ml/binutils/2010-10/msg00033.html
that fixes a problem with the LD/SD macro currently implemented by GAS for
the o32 ABI in an inconsistent way. This is best illustrated with a
simple program, which I'm copying here from the message above for easier
reference:
$ cat ld.s
ld $5,32767($4)
ld $5,32768($4)
This gets assebled into the following output:
$ mips-linux-as -32 -mips3 -o ld.o ld.s
$ mips-linux-objdump -d ld.o
ld.o: file format elf32-tradbigmips
Disassembly of section .text:
00000000 <.text>:
0: dc857fff ld a1,32767(a0)
4: 3c010001 lui at,0x1
8: 00810821 addu at,a0,at
c: 8c258000 lw a1,-32768(at)
10: 8c268004 lw a2,-32764(at)
...
Oops!
The GAS fix makes the macro behave in a consistent way and pairs of LW/SW
instructions to be output as appropriate regardless of the size of the
offset associated with the address used. The machine instruction is still
available, but to reach it macros have to be disabled first. This has a
side effect of requiring the use of a machine-addressable memory operand.
As some platforms require 64-bit operations for accesses to some I/O
registers LD/SD instructions are used in a couple of places in Linux
regardless of the ABI selected. Here's a fix for some pieces of code
affected I've been able to track down. The fix should be backwards
compatible with all supported binutils releases in existence and can be
used as a reference for any other places or off-tree code. The use of the
"R" constraint guarantees a machine-addressable operand.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1680/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In commit 7d172bfe ("Alchemy: Add UART PM methods") I introduced
platform PM methods which call a function of the 8250 driver;
this patch works around link failures when the kernel is built
without 8250 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1737/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This fixes IP22 and IP28 build errors.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The nvram_get function was never in the mainline kernel, it only existed in
an external OpenWrt patch. Use nvram_getenv function, which is in mainline
and use an include instead of an extra function declaration. et0macaddr
contains the mac address in text from like 00:11:22:33:44:55. We have to
parse it before adding it into macaddr.
nvram_parse_macaddr will be merged into asm/mach-bcm47xx/nvram.h through
the MIPS git tree and will be available soon. It will not build now without
nvram_parse_macaddr, but it hasn't before either.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: mb@bu3sch.de
Cc: netdev@vger.kernel.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Buesch <mb@bu3sch.de>
Patchwork: https://patchwork.linux-mips.org/patch/1849/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Some devices like the Netgear WGT634U are using ttyS1 for default console
output. We should switch to that console if it was given in the kernel_args
parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Instead of writing own function for parsing the mac address we now
use sscanf.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1847/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Fill the sprom with all available values from the nvram. Most of these
new values are needed for the b43 or b43legacy driver.
Parts of this patch have been in OpenWRT for a long time and were written
by Michael Buesch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1846/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The config options read out here are not stored in CFE but only in NVRAM on
the devices. Remove reading from CFE and only access the NVRAM. Reading out
CFE does not harm but is useless here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1845/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The totalsize field was be32. And the reserve bootmem would cause failure.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
To: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Dezhong Diao <dediao@cisco.com>
Patchwork: https://patchwork.linux-mips.org/patch/1838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Consider the following test case:
write_c0_compare(read_c0_count());
Even if the counter doesn't increment during execution, this might not
generate an interrupt until the counter wraps around. The CPU may
perform the comparison each time CP0 COUNT increments, not when CP0
COMPARE is written.
If mips_next_event() is called with a very small delta, and CP0 COUNT
increments during the calculation of "cnt += delta", it is possible
that CP0 COMPARE will be written with the current value of CP0 COUNT.
If this is detected, the function should return -ETIME, to indicate
that the interrupt might not have actually gotten scheduled.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
BCM4710 uses the BMIPS32 core (like BCM6345), not the MIPS 4Kc core as
was previously believed.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Alexandros C. Couloumbis <alex@ozo.com>
Patchwork: https://patchwork.linux-mips.org/patch/1837/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
As part the ASoC multi-component patch (commit f0fba2ad) the jz4740 pcm
driver was renamed to 'jz4740-pcm-audio'. Adjust the device name
accordingly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1770/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
partial_fixup is used in noreorder block.
Separating two consecutive loads can save one cycle on processors with
GPR intrelock and can fix load-use on processors that need a load delay slot.
Also do so for fwd_fixup.
[Ralf: Only R2000/R3000 class processors are lacking the the load-user
interlock and even some of those got it retrofitted. With R2000/R3000
being fairly uncommon these days the impact of this bug should be minor.]
Signed-off-by: Tony Wu <tung7970@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1768/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We were unconditionally sending SIGBUS with an empty siginfo on FP
emulator faults. This differs from what happens when real floating
point hardware would get a fault.
For most faults we need to send SIGSEGV with the faulting address
filled in in the struct siginfo.
Reported-by: Camm Maguire <camm@maguirefamily.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
TNETD7200 run their CPU clock faster than the default CPU clock we assume.
In order to have the correct loops per jiffies settings, initialize clocks right
before setting mips_hpt_frequency. As a side effect, we can no longer use
msleep in clocks.c which requires other parts of the kernel to be initialized,
so replace these with mdelay.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1749/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1748/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Recent changes to CONFIG_GENERIC_HARDIRQS have caused us to start getting:
warning: (SMP && SYS_SUPPORTS_SMP) selects IRQ_PER_CPU which has unmet direct dependencies (HAVE_GENERIC_HARDIRQS)
Rearranging our Kconfig quiets the message.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/1757/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
arch/mips/alchemy/devboards/prom.c: In function 'prom_init':
arch/mips/alchemy/devboards/prom.c:60: error: ignoring return value of
'strict_strtoul', declared with attribute warn_unused_result
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1761/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
cc1: warnings being treated as errors
arch/mips/loongson/common/env.c: In function 'prom_init_env':
arch/mips/loongson/common/env.c:49: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:50: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:51: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:52: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1762/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The return value of the vmalloc() call in arch/mips/kernel/vpe.c::vpe_open()
is not checked, so we potentially store a null pointer in v->pbuffer. Add
a check for a null return and then return -ENOMEM in that case.
[Ralf: The check added by Jesper's original patch is where it logically
should be. Adding it eleminated the need for the checks in a few other
places, so I removed them. There still is a zillion of other things that
need to be fixed in this file / API.]
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If PER_LINUX32 has been set on a 32-bit kernel, only twiddle with the
low-order personality bits, let the upper bits pass through.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1751/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The high bits of current->personality carry settings that we don't want to
clobber on each exec. Only clobber them if the lower bits that indicate
either PER_LINUX or PER_LINUX32 are invalid.
The clobbering prevents us from using useful bits like ADDR_NO_RANDOMIZE.
Reported-by: Camm Maguire <camm@maguirefamily.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1750/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch fixes the following section mismatch:
WARNING: arch/mips/built-in.o(.text+0xc): Section mismatch in reference from the
function jz4740_init_cmdline() to the variable .init.data:arcs_cmdline
While were at it, make jz4740_init_cmdline static as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1755/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch fixes the gpio number for the 6th row of the keyboard matrix.
(And fixes a typo in my name...)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: stable@kernel.org
Signed-off-by: https://patchwork.linux-mips.org/patch/1754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We never needed that (->regs[2] is overwritten on return from syscall paths
with return value of syscall, so storing it there early made no sense) and
with new restart logics since d27240bf7e61d2656de18e158ec910a902030847 it
has become really bad - we lose the original syscall number before the
place where we decide that we might need a syscall restart.
Note that for child we do need the assignment to regs[2] - it won't go
through the normal return from syscall path.
[Ralf: Issue found and reported by Lluís; initial investigations by me;
bug finally found and patch by Al; testing by me and Lluís.]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Lluís Batlle i Rossell <viriketo@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: populate initial_page_table
lguest: restore boot speed
lguest: fix crash lguest_time_init
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: fix regression of garbage collection ioctl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: define separate EVIOCGKEYCODE_V2/EVIOCSKEYCODE_V2
Input: wacom - add another Bamboo Pen ID (0xd4)
|
|
There are some situations (e.g. in __pm_generic_call()), where
pm_runtime_suspended() is used to decide whether or not to execute
a device's (system) ->suspend() callback. The callback is not
executed if pm_runtime_suspended() returns true, but it does so
for devices that don't even support runtime PM, because the
power.disable_depth device field is ignored by it. This leads to
problems (i.e. devices are not suspened when they should), so rework
pm_runtime_suspended() so that it returns false if the device's
power.disable_depth field is different from zero.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
|
|
Commit 3624eb0 (PM / Hibernate: Modify signature used to mark swap)
attempted to modify hibernate signature used to mark swap partitions
containing hibernation images, so that old kernels don't try to
handle compressed images. However, this change broke resume from
hibernation on Fedora 14 that apparently doesn't pass the resume=
argument to the kernel and tries to trigger resume from early user
space. This doesn't work, because the signature is now different,
so the old signature has to be restored to avoid the problem.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=22732 .
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Reported-by: Zhang Rui <rui.zhang@intel.com>
Reported-by: Pascal Chapperon <pascal.chapperon@wanadoo.fr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The user-space hibernation sends a wrong notification after the image
restoration because of thinko for the file flag check. RDONLY
corresponds to hibernation and WRONLY to restoration, confusingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
|
|
fbdev-fixes-for-linus
* 'for-paul-rc' of git://gitorious.org/linux-omap-dss2/linux:
OMAP: OMAPFB: disable old omapfb for OMAP4 builds
OMAP: DSS: VRAM: Align start & size of vram to 2M
|
|
It was always returning -1 (255), confusing test scripts.
Reported-by: Han Pingtian <phan@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Han Pingtian <phan@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
