| Age | Commit message (Collapse) | Author |
|---|
|
commit 64a32307b710c100beb101e9c78f8022f0e8ba61 upstream.
per comments in the bug report, this entry
seems to hurt at much as it helps.
https://bugzilla.kernel.org/show_bug.cgi?id=10807
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7a1d602f5fc35d14907b7da98d5627acb69589d1 upstream.
https://bugzilla.kernel.org/show_bug.cgi?id=12641
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4731fdcf6f7bdab3e369a3f844d4ea4d4017284d upstream.
When the Lenovo Ideapad S10-3 is booted with HT enabled,
it hits a boot hang in the intel_idle driver.
This occurs when entering ATM-C4 for the first time,
unless BM_STS is first cleared.
acpi_idle doesn't see this because it first checks
and clears BM_STS, but it would hit the same hang
if that check were disabled.
http://bugs.meego.com/show_bug.cgi?id=7093
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/634702
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 573b638158029898caf9470c8214b7ddd29751e3 upstream.
Section 4.7.3.1.1 (PM1 Status Registers) of version 4.0 of
the ACPI spec concerning PCIEXP_WAKE_STS points out in
in the final note field in table 4-11 that if this bit is
set to 1 and the system is put into a sleeping state then
the system will not automatically wake.
This bit gets set by hardware to indicate that the system
woke up due to a PCI Express wakeup event, so clear it during
acpi_hw_clear_acpi_status() calls to enable subsequent
resumes to work.
BugLink: http://bugs.launchpad.net/bugs/613381
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bcf64aa379fcadd074449cbf0c049da70071b06f upstream.
For carrier detection to work properly when binding the driver with a cable
unplugged, netif_carrier_off() should be called after register_netdev(),
not before.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 54a834043314c257210db2a9d59f8cc605571639 upstream.
In f761622e59433130bc33ad086ce219feee9eb961 we changed
early_setup_secondary so it's called using the proper kernel stack
rather than the emergency one.
Unfortunately, this stack pointer can't be used when translation is off
on PHYP as this stack pointer might be outside the RMO. This results in
the following on all non zero cpus:
cpu 0x1: Vector: 300 (Data Access) at [c00000001639fd10]
pc: 000000000001c50c
lr: 000000000000821c
sp: c00000001639ff90
msr: 8000000000001000
dar: c00000001639ffa0
dsisr: 42000000
current = 0xc000000016393540
paca = 0xc000000006e00200
pid = 0, comm = swapper
The original patch was only tested on bare metal system, so it never
caught this problem.
This changes __secondary_start so that we calculate the new stack
pointer but only start using it after we've called early_setup_secondary.
With this patch, the above problem goes away.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f761622e59433130bc33ad086ce219feee9eb961 upstream.
As early setup calls down to slb_initialize(), we must have kstack
initialised before checking "should we add a bolted SLB entry for our kstack?"
Failing to do so means stack access requires an SLB miss exception to refill
an entry dynamically, if the stack isn't accessible via SLB(0) (kernel text
& static data). It's not always allowable to take such a miss, and
intermittent crashes will result.
Primary CPUs don't have this issue; an SLB entry is not bolted for their
stack anyway (as that lives within SLB(0)). This patch therefore only
affects the init of secondaries.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 478971600e47cb83ff2d3c63c5c24f2b04b0d6a1 upstream.
bsg incorrectly returns sg's masked_status value for device_status.
[jejb: fix up expression logic]
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit aeb19f6052b5e5c8a24aa444fbff73b84341beac upstream.
We have fedora bug report where driver fail to initialize after
suspend/resume because of memory allocation errors:
https://bugzilla.redhat.com/show_bug.cgi?id=629158
To fix use GFP_KERNEL allocation where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 392bd0cb000d4aac9e88e4f50823db85e7220688 upstream.
Skge devices installed on some Gigabyte motherboards are not able to
perform 64 dma correctly due to board PCI implementation, so limit
DMA to 32bit if such boards are detected.
Bug was reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=447489
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ae2688d59b5f861dc70a091d003773975d2ae7fb upstream.
Blackhole routes are used when xfrm_lookup() returns -EREMOTE (error
triggered by IKE for example), hence this kind of route is always
temporary and so we should check if a better route exists for next
packets.
Bug has been introduced by commit d11a4dc18bf41719c9f0d7ed494d295dd2973b92.
Signed-off-by: Jianzhao Wang <jianzhao.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9828e6e6e3f19efcb476c567b9999891d051f52f upstream.
Just use explicit casts, since we really can't change the
types of structures exported to userspace which have been
around for 15 years or so.
Reported-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7e96dc7045bff8758804b047c0dfb6868f182500 upstream.
skb->truesize is set in core network.
Dont change it unless dealing with fragments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a4d258036ed9b2a1811c3670c6099203a0f284a0 upstream.
If a RST comes in immediately after checking sk->sk_err, tcp_poll will
return POLLIN but not POLLOUT. Fix this by checking sk->sk_err at the end
of tcp_poll. Additionally, ensure the correct order of operations on SMP
machines with memory barriers.
Signed-off-by: Tom Marshall <tdm.code@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b00916b189d13a615ff05c9242201135992fcda3 upstream.
Several other ethtool functions leave heap uncleared (potentially) by
drivers. Some interfaces appear safe (eeprom, etc), in that the sizes
are well controlled. In some situations (e.g. unchecked error conditions),
the heap will remain unchanged in areas before copying back to userspace.
Note that these are less of an issue since these all require CAP_NET_ADMIN.
[PG: 34 doesn't have ethtool_get_rxnfc(), drop that chunk]
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3d13008e7345fa7a79d8f6438150dc15d6ba6e9d upstream.
Special care should be taken when slow path is hit in ip_fragment() :
When walking through frags, we transfert truesize ownership from skb to
frags. Then if we hit a slow_path condition, we must undo this or risk
uncharging frags->truesize twice, and in the end, having negative socket
sk_wmem_alloc counter, or even freeing socket sooner than expected.
Many thanks to Nick Bowler, who provided a very clean bug report and
test program.
Thanks to Jarek for reviewing my first patch and providing a V2
While Nick bisection pointed to commit 2b85a34e911 (net: No more
expensive sock_hold()/sock_put() on each tx), underlying bug is older
(2.6.12-rc5)
A side effect is to extend work done in commit b2722b1c3a893e
(ip_fragment: also adjust skb->truesize for packets not owned by a
socket) to ipv6 as well.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com>
Tested-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ae878ae280bea286ff2b1e1cb6e609dd8cb4501d upstream.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a91e7d471e2e384035b9746ea707ccdcd353f5dd upstream.
Retrieve the header after doing pskb_may_pull since, pskb_may_pull
could change the buffer structure.
This is based on the comment given by Eric Dumazet on Phonet
Pipe controller patch for a similar problem.
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 482964e56e1320cb7952faa1932d8ecf59c4bf75 upstream.
This patch fixes the condition (3rd arg) passed to sk_wait_event() in
sk_stream_wait_memory(). The incorrect check in sk_stream_wait_memory()
causes the following soft lockup in tcp_sendmsg() when the global tcp
memory pool has exhausted.
>>> snip <<<
localhost kernel: BUG: soft lockup - CPU#3 stuck for 11s! [sshd:6429]
localhost kernel: CPU 3:
localhost kernel: RIP: 0010:[sk_stream_wait_memory+0xcd/0x200] [sk_stream_wait_memory+0xcd/0x200] sk_stream_wait_memory+0xcd/0x200
localhost kernel:
localhost kernel: Call Trace:
localhost kernel: [sk_stream_wait_memory+0x1b1/0x200] sk_stream_wait_memory+0x1b1/0x200
localhost kernel: [<ffffffff802557c0>] autoremove_wake_function+0x0/0x40
localhost kernel: [ipv6:tcp_sendmsg+0x6e6/0xe90] tcp_sendmsg+0x6e6/0xce0
localhost kernel: [sock_aio_write+0x126/0x140] sock_aio_write+0x126/0x140
localhost kernel: [xfs:do_sync_write+0xf1/0x130] do_sync_write+0xf1/0x130
localhost kernel: [<ffffffff802557c0>] autoremove_wake_function+0x0/0x40
localhost kernel: [hrtimer_start+0xe3/0x170] hrtimer_start+0xe3/0x170
localhost kernel: [vfs_write+0x185/0x190] vfs_write+0x185/0x190
localhost kernel: [sys_write+0x50/0x90] sys_write+0x50/0x90
localhost kernel: [system_call+0x7e/0x83] system_call+0x7e/0x83
>>> snip <<<
What is happening is, that the sk_wait_event() condition passed from
sk_stream_wait_memory() evaluates to true for the case of tcp global memory
exhaustion. This is because both sk_stream_memory_free() and vm_wait are true
which causes sk_wait_event() to *not* call schedule_timeout().
Hence sk_stream_wait_memory() returns immediately to the caller w/o sleeping.
This causes the caller to again try allocation, which again fails and again
calls sk_stream_wait_memory(), and so on.
[ Bug introduced by commit c1cbe4b7ad0bc4b1d98ea708a3fecb7362aa4088
("[NET]: Avoid atomic xchg() for non-error case") -DaveM ]
Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 01db403cf99f739f86903314a489fb420e0e254f upstream.
Fixes kernel bugzilla #16603
tcp_sendmsg() truncates iov_len to an 'int' which a 4GB write to write
zero bytes, for example.
There is also the problem higher up of how verify_iovec() works. It
wants to prevent the total length from looking like an error return
value.
However it does this using 'int', but syscalls return 'long' (and
thus signed 64-bit on 64-bit machines). So it could trigger
false-positives on 64-bit as written. So fix it to use 'long'.
Reported-by: Olaf Bonorden <bono@onlinehome.de>
Reported-by: Daniel Büse <dbuese@gmx.de>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 94e2238969e89f5112297ad2a00103089dde7e8f upstream.
otherwise ECT(1) bit will get interpreted as RTO_ONLINK
and routing will fail with XfrmOutBundleGenError.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f459ffbdfd04edb4a8ce6eea33170eb057a5e695 upstream.
fixes https://bugzilla.kernel.org/show_bug.cgi?id=19012
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 799c10559d60f159ab2232203f222f18fa3c4a5f upstream.
Don't try to "optimize" rds_page_copy_user() by using kmap_atomic() and
the unsafe atomic user mode accessor functions. It's actually slower
than the straightforward code on any reasonable modern CPU.
Back when the code was written (although probably not by the time it was
actually merged, though), 32-bit x86 may have been the dominant
architecture. And there kmap_atomic() can be a lot faster than kmap()
(unless you have very good locality, in which case the virtual address
caching by kmap() can overcome all the downsides).
But these days, x86-64 may not be more populous, but it's getting there
(and if you care about performance, it's definitely already there -
you'd have upgraded your CPU's already in the last few years). And on
x86-64, the non-kmap_atomic() version is faster, simply because the code
is simpler and doesn't have the "re-try page fault" case.
People with old hardware are not likely to care about RDS anyway, and
the optimization for the 32-bit case is simply buggy, since it doesn't
verify the user addresses properly.
Reported-by: Dan Rosenberg <drosenberg@vsecurity.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6dcbfe4f0b4e17e289d56fa534b7ce5a6b7f63a3 upstream.
This fixes possible cases of not collecting valid error info in
the MCE error thresholding groups on F10h hardware.
The current code contains a subtle problem of checking only the
Valid bit of MSR0000_0413 (which is MC4_MISC0 - DRAM
thresholding group) in its first iteration and breaking out if
the bit is cleared.
But (!), this MSR contains an offset value, BlkPtr[31:24], which
points to the remaining MSRs in this thresholding group which
might contain valid information too. But if we bail out only
after we checked the valid bit in the first MSR and not the
block pointer too, we miss that other information.
The thing is, MC4_MISC0[BlkPtr] is not predicated on
MCi_STATUS[MiscV] or MC4_MISC0[Valid] and should be checked
prior to iterating over the MCI_MISCj thresholding group,
irrespective of the MC4_MISC0[Valid] setting.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ec5a32f67c603b11d68eb283d94eb89a4f6cfce1 upstream.
adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit df6d02300f7c2fbd0fbe626d819c8e5237d72c62 upstream.
When a driver doesn't fill the entire buffer, old
heap contents may remain, and if it also doesn't
update the length properly, this old heap content
will be copied back to userspace.
It is very unlikely that this happens in any of
the drivers using private ioctls since it would
show up as junk being reported by iwpriv, but it
seems better to be safe here, so use kzalloc.
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1fc8a117865b54590acd773a55fbac9221b018f0 upstream.
ocfs2 fast symlinks are NUL terminated strings stored inline in the
inode data area. However, disk corruption or a local attacker could, in
theory, remove that NUL. Because we're using strlen() (my fault,
introduced in a731d1 when removing vfs_follow_link()), we could walk off
the end of that string.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6abb930af064fb1cf4177d32e2c7bfb89eee0fe5 upstream.
ret is still -1, if during the polling read_byte() returns at once
with I2C_PCA_CON_SI set. So ret > 0 would lead *_waitforcompletion()
to return 0, in spite of the proper behavior.
The routine was rewritten, so that ret has always a proper value,
before returning.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f13d4f979c518119bba5439dd2364d76d31dcd3f upstream.
The race is described as follows:
CPU X CPU Y
remove_hrtimer
// state & QUEUED == 0
timer->state = CALLBACK
unlock timer base
timer->f(n) //very long
hrtimer_start
lock timer base
remove_hrtimer // no effect
hrtimer_enqueue
timer->state = CALLBACK |
QUEUED
unlock timer base
hrtimer_start
lock timer base
remove_hrtimer
mode = INACTIVE
// CALLBACK bit lost!
switch_hrtimer_base
CALLBACK bit not set:
timer->base
changes to a
different CPU.
lock this CPU's timer base
The bug was introduced with commit ca109491f (hrtimer: removing all ur
callback modes) in 2.6.29
[ tglx: Feed new state via local variable and add a comment. ]
Signed-off-by: Salman Qazi <sqazi@google.com>
Cc: akpm@linux-foundation.org
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20101012142351.8485.21823.stgit@dungbeetle.mtv.corp.google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit cc60f8878eab892c03d06b10f389232b9b66bd83 upstream.
When using simultaneously the two DMA channels on a same engine, some
transfers are never completed. For example, an endless lock can occur
while writing heavily on a RAID5 array (with async-tx offload support
enabled).
Note that this issue can also be reproduced by using the DMA test
client.
On a same engine, the interrupt cause register is shared between two
DMA channels. This patch make sure that the cause bit is only cleared
for the requested channel.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Tested-by: Luc Saillard <luc@saillard.org>
Acked-by: saeed bishara <saeed.bishara@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d01343244abdedd18303d0323b518ed9cdcb1988 upstream.
Time stamps for the ring buffer are created by the difference between
two events. Each page of the ring buffer holds a full 64 bit timestamp.
Each event has a 27 bit delta stamp from the last event. The unit of time
is nanoseconds, so 27 bits can hold ~134 milliseconds. If two events
happen more than 134 milliseconds apart, a time extend is inserted
to add more bits for the delta. The time extend has 59 bits, which
is good for ~18 years.
Currently the time extend is committed separately from the event.
If an event is discarded before it is committed, due to filtering,
the time extend still exists. If all events are being filtered, then
after ~134 milliseconds a new time extend will be added to the buffer.
This can only happen till the end of the page. Since each page holds
a full timestamp, there is no reason to add a time extend to the
beginning of a page. Time extends can only fill a page that has actual
data at the beginning, so there is no fear that time extends will fill
more than a page without any data.
When reading an event, a loop is made to skip over time extends
since they are only used to maintain the time stamp and are never
given to the caller. As a paranoid check to prevent the loop running
forever, with the knowledge that time extends may only fill a page,
a check is made that tests the iteration of the loop, and if the
iteration is more than the number of time extends that can fit in a page
a warning is printed and the ring buffer is disabled (all of ftrace
is also disabled with it).
There is another event type that is called a TIMESTAMP which can
hold 64 bits of data in the theoretical case that two events happen
18 years apart. This code has not been implemented, but the name
of this event exists, as well as the structure for it. The
size of a TIMESTAMP is 16 bytes, where as a time extend is only
8 bytes. The macro used to calculate how many time extends can fit on
a page used the TIMESTAMP size instead of the time extend size
cutting the amount in half.
The following test case can easily trigger the warning since we only
need to have half the page filled with time extends to trigger the
warning:
# cd /sys/kernel/debug/tracing/
# echo function > current_tracer
# echo 'common_pid < 0' > events/ftrace/function/filter
# echo > trace
# echo 1 > trace_marker
# sleep 120
# cat trace
Enabling the function tracer and then setting the filter to only trace
functions where the process id is negative (no events), then clearing
the trace buffer to ensure that we have nothing in the buffer,
then write to trace_marker to add an event to the beginning of a page,
sleep for 2 minutes (only 35 seconds is probably needed, but this
guarantees the bug), and then finally reading the trace which will
trigger the bug.
This patch fixes the typo and prevents the false positive of that warning.
Reported-by: Hans J. Koch <hjk@linutronix.de>
Tested-by: Hans J. Koch <hjk@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 47526903feb52f4c26a6350370bdf74e337fcdb1 upstream.
Commit f81f2f7c (ubd: drop unnecessary rq->sector manipulation)
dropped request->sector manipulation in preparation for global request
handling cleanup; unfortunately, it incorrectly assumed that the
updated sector wasn't being used.
ubd tries to issue as many requests as possible to io_thread. When
issuing fails due to memory pressure or other reasons, the device is
put on the restart list and issuing stops. On IO completion, devices
on the restart list are scanned and IO issuing is restarted.
ubd issues IOs sg-by-sg and issuing can be stopped in the middle of a
request, so each device on the restart queue needs to remember where
to restart in its current request. ubd needs to keep track of the
issue position itself because,
* blk_rq_pos(req) is now updated by the block layer to keep track of
_completion_ position.
* Multiple io_req's for the current request may be in flight, so it's
difficult to tell where blk_rq_pos(req) currently is.
Add ubd->rq_pos to keep track of the issue position and use it to
correctly restart io_req issue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Tested-by: Chris Frey <cdfrey@foursquare.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1cf180c94e9166cda083ff65333883ab3648e852 upstream.
free_irq_cfg() is not freeing the cpumask_vars in irq_cfg. Fixing this
triggers a use after free caused by the fact that copying struct
irq_cfg is done with memcpy, which copies the pointer not the cpumask.
Fix both places.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
LKML-Reference: <alpine.LFD.2.00.1009282052570.2416@localhost6.localdomain6>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 021989622810b02aab4b24f91e1f5ada2b654579 upstream.
create_irq() returns -1 if the interrupt allocation failed, but the
code checks for irq == 0.
Use create_irq_nr() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Venkatesh Pallipadi <venki@google.com>
LKML-Reference: <alpine.LFD.2.00.1009282310360.2416@localhost6.localdomain6>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d2520a426dc3033c00077e923a553fc6c98c7564 upstream.
Fixed JSIOCSAXMAP ioctl to update absmap, the map from hardware axis to
event axis in addition to abspam. This fixes a regression introduced
by 999b874f.
Signed-off-by: Kenneth Waters <kwwaters@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c10469c637602c2385e2993d8c730cc44fd47d23 upstream.
As reported by: Carlos Americo Domiciano <c_domiciano@yahoo.com.br>:
[ 220.033500] cx231xx v4l2 driver loaded.
[ 220.033571] cx231xx #0: New device Conexant Corporation Polaris AV Capturb @ 480 Mbps (1554:5010) with 6 interfaces
[ 220.033577] cx231xx #0: registering interface 0
[ 220.033591] cx231xx #0: registering interface 1
[ 220.033654] cx231xx #0: registering interface 6
[ 220.033910] cx231xx #0: Identified as Unknown CX231xx video grabber (card=0)
[ 220.033946] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 220.033955] IP: [<ffffffffa0d3c8bd>] cx231xx_pre_card_setup+0x5d/0xb0 [cx231xx]
Thanks-to: Carlos Americo Domiciano <c_domiciano@yahoo.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3e645d6b485446c54c6745c5e2cf5c528fe4deec upstream.
The compat code for the VIDIOCSMICROCODE ioctl is totally buggered.
It's only used by the VIDEO_STRADIS driver, and that one is scheduled to
staging and eventually removed unless somebody steps up to maintain it
(at which point it should use request_firmware() rather than some magic
ioctl). So we'll get rid of it eventually.
But in the meantime, the compatibility ioctl code is broken, and this
tries to get it to at least limp along (even if Mauro suggested just
deleting it entirely, which may be the right thing to do - I don't think
the compatibility translation code has ever worked unless you were very
lucky).
Reported-by: Kees Cook <kees.cook@canonical.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 258af47479980d8238a04568b94a4e55aa1cb537 upstream.
The guest can use the paravirt clock in kvmclock.c which is used
by sched_clock(), which in turn is used by the tracing mechanism
for timestamps, which leads to infinite recursion.
Disable mcount/tracing for kvmclock.o.
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9ecd4e1689208afe9b059a5ce1333acb2f42c4d2 upstream.
When using a paravirt clock, pvclock.c can be used by sched_clock(),
which in turn is used by the tracing mechanism for timestamps,
which leads to infinite recursion.
Disable mcount/tracing for pvclock.o.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
LKML-Reference: <4C9A9A3F.4040201@goop.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4c894f47bb49284008073d351c0ddaac8860864e upstream.
This patch adds a workaround for an IOMMU BIOS problem to
the AMD IOMMU driver. The result of the bug is that the
IOMMU does not execute commands anymore when the system
comes out of the S3 state resulting in system failure. The
bug in the BIOS is that is does not restore certain hardware
specific registers correctly. This workaround reads out the
contents of these registers at boot time and restores them
on resume from S3. The workaround is limited to the specific
IOMMU chipset where this problem occurs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 04e0463e088b41060c08c255eb0d3278a504f094 upstream.
In the __unmap_single function the dma_addr is rounded down
to a page boundary before the dma pages are unmapped. The
address is later also used to flush the TLB entries for that
mapping. But without the offset into the dma page the amount
of pages to flush might be miscalculated in the TLB flushing
path. This patch fixes this bug by using the original
address to flush the TLB.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e9bf51971157e367aabfc111a8219db010f69cd4 upstream.
This patch moves the setting of the configuration and
feature flags out out the acpi table parsing path and moves
it into the iommu-enable path. This is needed to reliably
fix resume-from-s3.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9320f7cbbdd5febf013b0e91db29189724057738 upstream.
If not all clocks have been defined in platform data, the driver will
cause a null pointer dereference when it is removed. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bec658ff31453a5726b1c188674d587a5d40c482 upstream.
The HW by default has RX coalescing on. For iWARP connections, this
causes a 100ms delay in connection establishement due to the ingress
MPA Start message being stalled in HW. So explicitly turn RX
coalescing off when setting up iWARP connections.
This was causing very bad performance for NP64 gather operations using
Open MPI, due to the way it sets up connections on larger jobs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bb7ab785ad05a97a2c9ffb3a06547ed39f3133e8 upstream.
This patch adds CPU type detection for dunnington processor (Family 6
/ Model 29) to be identified as core 2 family cpu type (wikipedia
source).
I tested oprofile on Intel(R) Xeon(R) CPU E7440 reporting itself as
model 29, and it runs without an issue.
Spec:
http://www.intel.com/Assets/en_US/PDF/specupdate/320336.pdf
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a666e3e6098a9f56310e4ec2705f1dad124a34b5 upstream.
Commit 46034dca515bc4ddca0399ae58106d1f5f0d809f (USB: musb_gadget_ep0: stop
abusing musb_gadget_set_halt()) forgot to restart a queued request after
clearing the endpoint halt feature. This results in a couple of USB resets
while enumerating the file-backed storage gadget due to CSW packet not being
sent for the MODE SENSE(10) command.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bd2e74d657fc7d514881cc2117e323790b257914 upstream.
For shared fifo hw endpoint(with FIFO_TXRX style), only ep_in
field of musb_hw_ep is intialized in musb_g_init_endpoints, and
ep_out is not initialized, but musb_g_rx and rxstate may access
ep_out field of musb_hw_ep by the method below:
musb_ep = &musb->endpoints[epnum].ep_out
which can cause the kernel panic[1] below, this patch fixes the issue
by getting 'musb_ep' from '&musb->endpoints[epnum].ep_in' for shared fifo
endpoint.
[1], kernel panic
[root@OMAP3EVM /]# musb_interrupt 1583: ** IRQ peripheral usb0008 tx0000 rx4000
musb_stage0_irq 460: <== Power=f0, DevCtl=99, int_usb=0x8
musb_g_rx 772: <== (null), rxcsr 4007 ffffffe8
musb_g_rx 786: iso overrun on ffffffe8
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = c0004000
[00000008] *pgd=00000000
Internal error: Oops: 17 [#1] PREEMPT
last sysfs file: /sys/devices/platform/musb_hdrc/usb1/usb_device/usbdev1.1/dev
Modules linked in: g_zero
CPU: 0 Tainted: G W (2.6.35-rc6-gkh-wl+ #92)
PC is at musb_g_rx+0xfc/0x2ec
LR is at vprintk+0x3f4/0x458
pc : [<c02c07a4>] lr : [<c006ccb0>] psr: 20000193
sp : c760bd78 ip : c03c9d70 fp : c760bdbc
r10: 00000000 r9 : fa0ab1e0 r8 : 0000000e
r7 : c7e80158 r6 : ffffffe8 r5 : 00000001 r4 : 00004003
r3 : 00010003 r2 : c760bcd8 r1 : c03cd030 r0 : 0000002e
Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 8778c019 DAC: 00000017
Process kmemleak (pid: 421, stack limit = 0xc760a2e8)
Stack: (0xc760bd78 to 0xc760c000)
bd60: ffffffe8 c04b1b58
bd80: ffffffe8 c7c01ac0 00000000 c7e80d24 c0084238 00000001 00000001 c7e80158
bda0: 0000000e 00000008 00000099 000000f0 c760be04 c760bdc0 c02bcd68 c02c06b4
bdc0: 00000099 00000008 00004000 c760bdd8 c03cc4f8 00000000 00000002 c7e80158
bde0: c7d2e300 60000193 c760a000 0000005c 00000000 00000000 c760be24 c760be08
be00: c02bcecc c02bc1ac c7d2e300 c7d2e300 0000005c c760a000 c760be54 c760be28
be20: c00ad698 c02bce6c 00000000 c7d2e300 c067c258 0000005c c067c294 00000001
be40: c760a000 00000000 c760be74 c760be58 c00af984 c00ad5fc 0000005c 00000000
be60: 00000000 00000002 c760be8c c760be78 c0039080 c00af8d0 ffffffff fa200000
be80: c760beec c760be90 c0039b6c c003900c 00000001 00000000 c7d1e240 00000000
bea0: 00000000 c068bae8 00000000 60000013 00000001 00000000 00000000 c760beec
bec0: c0064ecc c760bed8 c00ff7d0 c003a0a8 60000013 ffffffff 00000000 c068bae8
bee0: c760bf24 c760bef0 c00ff7d0 c0064ec4 00000001 00000000 c00ff700 00000000
bf00: c0087f00 00000000 60000013 c0d76a70 c0e23795 00000001 c760bf4c c760bf28
bf20: c00ffdd8 c00ff70c c068bb08 c068bae8 60000013 c0100938 c068bb30 00000000
bf40: c760bf84 c760bf50 c010014c c00ffd84 00000001 00000000 c010000c 00012c00
bf60: c7c33f04 00012c00 c7c33f04 00000000 c0100938 00000000 c760bf9c c760bf88
bf80: c01009a8 c0100018 c760bfa8 c7c33f04 c760bff4 c760bfa0 c0088000 c0100944
bfa0: c760bf98 00000000 00000000 00000001 dead4ead ffffffff ffffffff c08ba2bc
bfc0: 00000000 c049e7fa 00000000 c0087f70 c760bfd0 c760bfd0 c7c33f04 c0087f70
bfe0: c006f5e8 00000013 00000000 c760bff8 c006f5e8 c0087f7c 7f0004ff df2000ff
Backtrace:
[<c02c06a8>] (musb_g_rx+0x0/0x2ec) from [<c02bcd68>] (musb_interrupt+0xbc8/0xcc0)
[<c02bc1a0>] (musb_interrupt+0x0/0xcc0) from [<c02bcecc>] (generic_interrupt+0x6c/0x84)
[<c02bce60>] (generic_interrupt+0x0/0x84) from [<c00ad698>] (handle_IRQ_event+0xa8/0x1ec)
r7:c760a000 r6:0000005c r5:c7d2e300 r4:c7d2e300
[<c00ad5f0>] (handle_IRQ_event+0x0/0x1ec) from [<c00af984>] (handle_level_irq+0xc0/0x13c)
[<c00af8c4>] (handle_level_irq+0x0/0x13c) from [<c0039080>] (asm_do_IRQ+0x80/0xa0)
r7:00000002 r6:00000000 r5:00000000 r4:0000005c
[<c0039000>] (asm_do_IRQ+0x0/0xa0) from [<c0039b6c>] (__irq_svc+0x4c/0xb4)
Exception stack(0xc760be90 to 0xc760bed8)
be80: 00000001 00000000 c7d1e240 00000000
bea0: 00000000 c068bae8 00000000 60000013 00000001 00000000 00000000 c760beec
bec0: c0064ecc c760bed8 c00ff7d0 c003a0a8 60000013 ffffffff
r5:fa200000 r4:ffffffff
[<c0064eb8>] (sub_preempt_count+0x0/0x100) from [<c00ff7d0>] (find_and_get_object+0xd0/0x110)
r5:c068bae8 r4:00000000
[<c00ff700>] (find_and_get_object+0x0/0x110) from [<c00ffdd8>] (scan_block+0x60/0x104)
r8:00000001 r7:c0e23795 r6:c0d76a70 r5:60000013 r4:00000000
[<c00ffd78>] (scan_block+0x0/0x104) from [<c010014c>] (kmemleak_scan+0x140/0x484)
[<c010000c>] (kmemleak_scan+0x0/0x484) from [<c01009a8>] (kmemleak_scan_thread+0x70/0xcc)
r8:00000000 r7:c0100938 r6:00000000 r5:c7c33f04 r4:00012c00
[<c0100938>] (kmemleak_scan_thread+0x0/0xcc) from [<c0088000>] (kthread+0x90/0x98)
r5:c7c33f04 r4:c760bfa8
[<c0087f70>] (kthread+0x0/0x98) from [<c006f5e8>] (do_exit+0x0/0x684)
r7:00000013 r6:c006f5e8 r5:c0087f70 r4:c7c33f04
Code: e3002312 e58d6000 e2833e16 eb0422d5 (e5963020)
---[ end trace f3d5e96f75c297b7 ]---
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 0026e00523a85b90a92a93ddf6660939ecef3e54 upstream.
Recent changes in the usbhid layer exposed a bug in usbcore. If
CONFIG_USB_DYNAMIC_MINORS is enabled then an interface may be assigned
a minor number of 0. However interfaces that aren't registered as USB
class devices also have their minor number set to 0, during
initialization. As a result usb_find_interface() may return the
wrong interface, leading to a crash.
This patch (as1418) fixes the problem by initializing every
interface's minor number to -1. It also cleans up the
usb_register_dev() function, which besides being somewhat awkwardly
written, does not unwind completely on all its error paths.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Philip J. Turmel <philip@turmel.org>
Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Matthias Bayer <jackdachef@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit aa73aec6c385e2c797ac25cc7ccf0318031de7c8 upstream.
When a driver module is unloaded and the last still open file is a raw
MIDI device, the card and its devices will be actually freed in the
snd_card_file_remove() call when that file is closed. Afterwards, rmidi
and rmidi->card point into freed memory, so the module pointer is likely
to be garbage.
(This was introduced by commit 9a1b64caac82aa02cb74587ffc798e6f42c6170a.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Krzysztof Foltman <wdev@foltman.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 5591bf07225523600450edd9e6ad258bb877b779 upstream.
The snd_ctl_new() function in sound/core/control.c allocates space for a
snd_kcontrol struct by performing arithmetic operations on a
user-provided size without checking for integer overflow. If a user
provides a large enough size, an overflow will occur, the allocated
chunk will be too small, and a second user-influenced value will be
written repeatedly past the bounds of this chunk. This code is
reachable by unprivileged users who have permission to open
a /dev/snd/controlC* device (on many distros, this is group "audio") via
the SNDRV_CTL_IOCTL_ELEM_ADD and SNDRV_CTL_IOCTL_ELEM_REPLACE ioctls.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
