| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This is a revert of commit 9b29050f8f75916f974a2d231ae5d3cd59792296
upstream which has been found to prevent suspend from working on a
number of systems.
Thanks to Jiri Slaby <jirislaby@gmail.com> for tracing this down.
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Rafael Wysocki <rjw@sisk.pl>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8a6a142c1286797978e4db266d22875a5f424897 upstream.
Don't allow everybody to change WMI settings.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8040835760adf0ef66876c063d47f79f015fb55d upstream.
Don't allow everybody to change ACPI settings. The comment says that it
is done deliberatelly, however, the comment before disp_proc_write()
says that at least one of these setting is experimental.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b80b168f918bba4b847e884492415546b340e19d upstream.
Don't allow everybody to write to hardware registers.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1e6d93e45b231b3ae87c01902ede2315aacfe976 upstream.
Don't allow everybody to set terminator via sysfs.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3088e3b4963d26d6f6f54987f595b974ed6d48d8 upstream.
The mic detection HW should be enabled when either mic or short detection
is required, not when only both are required.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4fe757dd48a9e95e1a071291f15dda5421dacb66 upstream.
It was possible to call pmu::start() on an already running event. In
particular this lead so some wreckage as the hrtimer events would
re-initialize active timers.
This was due to throttled events being activated again by scheduling.
Scheduling in a context would add and force start events, resulting in
running events with a possible throttle status. The next tick to hit
that task will then try to unthrottle the event and call ->start() on
an already running event.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6d83f94db95cfe65d2a6359cccdf61cf087c2598 upstream.
With CONFIG_SHIRQ_DEBUG=y we call a newly installed interrupt handler
in request_threaded_irq().
The original implementation (commit a304e1b8) called the handler
_BEFORE_ it was installed, but that caused problems with handlers
calling disable_irq_nosync(). See commit 377bf1e4.
It's braindead in the first place to call disable_irq_nosync in shared
handlers, but ....
Moving this call after we installed the handler looks innocent, but it
is very subtle broken on SMP.
Interrupt handlers rely on the fact, that the irq core prevents
reentrancy.
Now this debug call violates that promise because we run the handler
w/o the IRQ_INPROGRESS protection - which we cannot apply here because
that would result in a possibly forever masked interrupt line.
A concurrent real hardware interrupt on a different CPU results in
handler reentrancy and can lead to complete wreckage, which was
unfortunately observed in reality and took a fricking long time to
debug.
Leave the code here for now. We want this debug feature, but that's
not easy to fix. We really should get rid of those
disable_irq_nosync() abusers and remove that function completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c1ee6264280e740a9d3ff3feef38642cf0a57013 upstream.
Lars-Peter Clausen pointed out:
I stumbled upon this while looking through the existing archs using
SPARSE_IRQ. Even with SPARSE_IRQ the NR_IRQS is still the upper
limit for the number of IRQs.
Both PXA and MMP set NR_IRQS to IRQ_BOARD_START, with
IRQ_BOARD_START being the number of IRQs used by the core.
In various machine files the nr_irqs field of the ARM machine
defintion struct is then set to "IRQ_BOARD_START + NR_BOARD_IRQS".
As a result "nr_irqs" will greater then NR_IRQS which then again
causes the "allocated_irqs" bitmap in the core irq code to be
accessed beyond its size overwriting unrelated data.
The core code really misses a sanity check there.
This went unnoticed so far as by chance the compiler/linker places
data behind that bitmap which gets initialized later on those affected
platforms.
So the obvious fix would be to add a sanity check in early_irq_init()
and break all affected platforms. Though that check wants to be
backported to stable as well, which will require to fix all known
problematic platforms and probably some more yet not known ones as
well. Lots of churn.
A way simpler solution is to allocate a slightly larger bitmap and
avoid the whole churn w/o breaking anything. Add a few warnings when
an arch returns utter crap.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 55f9cf6bbaa682958a7dd2755f883b768270c3ce upstream.
The lower filesystem may do some type of inode revalidation during a
getattr call. eCryptfs should take advantage of that by copying the
lower inode attributes to the eCryptfs inode after a call to
vfs_getattr() on the lower inode.
I originally wrote this fix while working on eCryptfs on nfsv3 support,
but discovered it also fixed an eCryptfs on ext4 nanosecond timestamp
bug that was reported.
https://bugs.launchpad.net/bugs/613873
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 33619f0d3ff715a2a5499520967d526ad931d70d upstream.
Allow drivers to enable Zoomed Video support. Currently, this is only
used by out-of-tree drivers (L64020 DVB driver in particular).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bbb706079abe955a9e3f208f541de97d99449236 upstream.
6AF4F258-B401-42fd-BE91-3D4AC2D7C0D3 needs to be
6AF4F258-B401-42FD-BE91-3D4AC2D7C0D3 to match the hardware alias.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5e640927a597a7c3e72b61e8bce74c22e906de65 upstream.
LANMAN response length was changed to 16 bytes instead of 24 bytes.
Revert it back to 24 bytes.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9616125611ee47693186533d76e403856a36b3c8 upstream.
The code finds, the '%' sign in an ipv6 address and copies that to a
buffer allocated on the stack. It then ignores that buffer, and passes
'pct' to simple_strtoul(), which doesn't work right because we're
comparing 'endp' against a completely different string.
Fix it by passing the correct pointer. While we're at it, this is a
good candidate for conversion to strict_strtoul as well.
Cc: David Howells <dhowells@redhat.com>
Reported-by: Björn JACKE <bj@sernet.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a9ad21fed09cb95d34af9474be0831525b30c4c6 upstream.
When SMP_ON_UP is used and the spinlocks are inlined, we end up with
inline spinlocks in the exit code, with references from the SMP
alternatives section to the exit sections. This causes link time
errors. Avoid this by placing the exit sections in the init-discarded
region.
Tested-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 53399053eb505cf541b2405bd9d9bca5ecfb96fb upstream.
Ensure a predictable endian state when entering signal handlers. This
avoids programs which use SETEND to momentarily switch their endian
state from having their signal handlers entered with an unpredictable
endian state.
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2400982a2e8a8e4e95f0a0e1517bbe63cc88038f upstream.
Commit e3c92215198cb6aa00ad38db2780faa6b72e0a3f ("[media] radio-aimslab.c: Fix
gcc 4.5+ bug") removed the include, but introduced new callers of msleep():
| drivers/media/radio/radio-aimslab.c: In function ‘rt_decvol’:
| drivers/media/radio/radio-aimslab.c:76: error: implicit declaration of function ‘msleep’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: dann frazier <dannf@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c71caf4114a0e1da3451cc92fba6a152929cd4c2 upstream.
In 13ee6ac netfilter: fix race in conntrack between dump_table and
destroy, we recovered spinlocks to protect the dump of the conntrack
table according to reports from Stephen and acknowledgments on the
issue from Eric.
In that patch, the refcount bump that allows to keep a reference
to the current ct object was removed. However, we still decrement
the refcount for that object in the output path of
ctnetlink_dump_table():
if (last)
nf_ct_put(last)
Cc: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 13ee6ac579574a2a95e982b19920fd2495dce8cd upstream.
The netlink interface to dump the connection tracking table has a race
when entries are deleted at the same time. A customer reported a crash
and the backtrace showed thatctnetlink_dump_table was running while a
conntrack entry was being destroyed.
(see https://bugzilla.vyatta.com/show_bug.cgi?id=6402).
According to RCU documentation, when using hlist_nulls the reader
must handle the case of seeing a deleted entry and not proceed
further down the linked list. The old code would continue
which caused the scan to walk into the free list.
This patch uses locking (rather than RCU) for this operation which
is guaranteed safe, and no longer requires getting reference while
doing dump operation.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2c6315da6a1657a49e03970a4084dc3d1958ad70 upstream.
On systems where the temperature sensor is actually used, the BIOS is
likely to have locked the alarm registers. In that case, all writes
through the corresponding sysfs files would be silently ignored.
To prevent this, detect the locks and make the affected sysfs files
read-only.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d5622f5b6c4671d1588ccc9056705366d4eb312a upstream.
The documentation lists standard numbers and chip names in excruciating
detail, but that's all it does. To help mere mortals in deciding
whether to enable this driver, mention what this sensor is for and in
which systems it might be found.
Also add a link to the actual JC 42.4 specification.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e866729605a43a739fc56023a8530b07a93d3458 upstream.
In set_temp_crit_hyst(), make the variable 'val' have the correct
type for strict_strtoul().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit aa4790a6287818078ca968164a5f0d0870326602 upstream.
Add the PCI ID to support the internal temperature sensor of the
AMD "Llano" and "Brazos" processor families.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ca86828ccd3128513f6d4e200b437deac95408db upstream.
This patch adds the PCI northbridge device id for AMD CPU
families 12h and 14h. Both families have implemented the same
PCI northbridge device.
There are some future use cases that use this PCI device and
we would like to clarify its naming.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: xen-devel@lists.xensource.com <xen-devel@lists.xensource.com>
Cc: Keir Fraser <keir@xen.org>
Cc: Jan Beulich <JBeulich@novell.com>
LKML-Reference: <20110106165107.GL4739@erda.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f065a93e168299569078bc6f52128b57f602fff3 upstream.
The interface is identical EMC6D102, so all that needs to be added are
some definitions and their uses.
Registers apparently missing in EMC6D103S/EMC6D103:A2 compared to EMC6D103:A0,
EMC6D103:A1, and EMC6D102 (according to the data sheets), but used
unconditionally in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. For that
reason, EMC6D103S chips don't get enabled for the time being.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
(Guenter Roeck: Replaced EMC6D103_A2 with EMC6D103S per EMC6D103S datasheet)
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 89724958e5d596bb91328644c97dd80399443e87 upstream.
Without this patch, one line-out and one speaker and
Conexant's auto parser would announce (non-working) surround
capabilities.
BugLink: http://bugs.launchpad.net/bugs/721126
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit eaae55dac6b64c0616046436b294e69fc5311581 upstream.
Use strlcpy() to assure not to overflow the string array sizes by
too long USB device name string.
Reported-by: Rafa <rafa@mwrinfosecurity.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b540afc2b3d6e4cd1d1f137ef6d9e9c78d67fecd upstream.
The bug reporter claims that position_fix=1 is needed for his
microphone to work. The controller PCI vendor-id is [1002:4383] (rev 40).
Reported-by: Kjell L.
BugLink: http://bugs.launchpad.net/bugs/718402
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c91d01556f52255a31575be0cb1981c92a2a5028 upstream.
Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599
Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.
For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.
Bug reporter confirmed that removing plcp check fixed problem for him.
Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ceaaec98ad99859ac90ac6863ad0a6cd075d8e0e upstream.
commit 9b5e383c11b08784 (net: Introduce
unregister_netdevice_many()) left an active LIST_HEAD() in
rollback_registered(), with possible memory corruption.
Even if device is freed without touching its unreg_list (and therefore
touching the previous memory location holding LISTE_HEAD(single), better
close the bug for good, since its really subtle.
(Same fix for default_device_exit_batch() for completeness)
Reported-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Eric W. Biderman <ebiderman@xmission.com>
Tested-by: Eric W. Biderman <ebiderman@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3233cdbd9fa347a6d6897a94cc6ed0302ae83c4f upstream.
MAYDAY_INITIAL_TIMEOUT is defined as HZ / 100 and depending on
configuration may end up 0 or 1. Even when it's 1, depending on when
the mayday timer is added in the current jiffy interval, it may expire
way before a jiffy has passed.
Make sure MAYDAY_INITIAL_TIMEOUT is at least two to guarantee that at
least a full jiffy has passed before calling rescuers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7576958a9d5a4a677ad7dd40901cdbb6c1110c98 upstream.
After executing the matching works, a rescuer leaves the gcwq whether
there are more pending works or not. This may decrease the
concurrency level to zero and stall execution until a new work item is
queued on the gcwq.
Make rescuer wake up a regular worker when it leaves a gcwq if there
are more works to execute, so that execution isn't stalled.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit fa7ea87a057958a8b7926c1a60a3ca6d696328ed upstream.
Validate number of blocks in map and remove redundant variable.
Signed-off-by: Timo Warns <warns@pre-sense.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9f4283f49f0a96a64c5a45fe56f0f8c942885eef upstream.
The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+. Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29272
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2e725a065b0153f0c449318da1923a120477633d upstream.
Currently we return 0 in swsusp_alloc() when alloc_image_page() fails.
Fix that. Also remove unneeded "error" variable since the only
useful value of error is -ENOMEM.
[rjw: Fixed up the changelog and changed subject.]
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a backport for 2.6.37 stable. The original commit ID is
6550904ddbc3c286798a87edf95eeebcc62bc58a
Offlining the secondary CPU causes the timer irq affinity to be set to
CPU 0. When the secondary CPU is back online again, the wrong irq
affinity will be used.
This patch ensures secondary per CPU timer always has the correct
IRQ affinity when enabled.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
LKML-Reference: <1294963604-18111-1-git-send-email-jacob.jun.pan@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 261cd298a8c363d7985e3482946edb4bfedacf98 upstream.
task_show_regs used to be a debugging aid in the early bringup days
of Linux on s390. /proc/<pid>/status is a world readable file, it
is not a good idea to show the registers of a process. The only
correct fix is to remove task_show_regs.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Upstream commits: 93789b32dbf355e70f18b17a82e8661677a7f7fb,
1c9d16e35911090dee3f9313e6af13af623d66ee
ea53069231f9317062910d6e772cca4ce93de8c8 made a CPU use monitor/mwait
when offline. This is not the optimal choice for AMD wrt to powersavings
and we'd prefer our cores to halt (i.e. enter C1) instead. For this, the
same selection whether to use monitor/mwait has to be used as when we
select the idle routine for the machine.
With this patch, offlining cores 1-5 on a X6 machine allows core0 to
boost again.
[ hpa: putting this in urgent since it is a (power) regression fix ]
Reported-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.hl>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1295534572-10730-1-git-send-email-bp@amd64.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 47c85291d3dd1a51501555000b90f8e281a0458e upstream.
These functions return an nfs status, not a host_err. So don't
try to convert before returning.
This is a regression introduced by
3c726023402a2f3b28f49b9d90ebf9e71151157d; I fixed up two of the callers,
but missed these two.
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a backport of mainline kernel commit
2a5d24286e8bdafdc272b37ec5bdd9e977b3767c.
Commit 9630bdd (ACPI: Use GPE reference counting to support shared
GPEs) introduced a suspend regression where boxes resume immediately
after being suspended due to the lid or sleep button wakeup status
not being cleared properly. This happens if the GPEs corresponding
to those devices are not enabled all the time, which apparently is
expected by some BIOSes.
To fix this problem, enable button and lid GPEs unconditionally
during initialization and keep them enabled all the time, regardless
of whether or not the ACPI button driver is used.
References: https://bugzilla.kernel.org/show_bug.cgi?id=27372
Reported-and-tested-by: Ferenc Wágner <wferi@niif.hu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a628e7b87e100befac9702aa0c3b9848a7685e49 upstream.
This reintroduces commit 47970b1b which was subsequently reverted
as f00eaeea. The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space. The normal capable() interface returns
true on success, but the LSM interface returns 0 on success. This thinko
is now fixed in this patch, and has been confirmed to work properly.
So, once again...Eric Paris noted that commit de139a3 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: Eric Paris <eparis@redhat.com>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6037b715d6fab139742c3df8851db4c823081561 upstream.
Expand security_capable() to include cred, so that it can be usable in a
wider range of call sites.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit fb2b2a1d37f80cc818fd4487b510f4e11816e5e1 upstream.
In prepare_kernel_cred() since 2.6.29, put_cred(new) is called without
assigning new->usage when security_prepare_creds() returned an error. As a
result, memory for new and refcount for new->{user,group_info,tgcred} are
leaked because put_cred(new) won't call __put_cred() unless old->usage == 1.
Fix these leaks by assigning new->usage (and new->subscribers which was added
in 2.6.32) before calling security_prepare_creds().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2edeaa34a6e3f2c43b667f6c4f7b27944b811695 upstream.
In cred_alloc_blank() since 2.6.32, abort_creds(new) is called with
new->security == NULL and new->magic == 0 when security_cred_alloc_blank()
returns an error. As a result, BUG() will be triggered if SELinux is enabled
or CONFIG_DEBUG_CREDENTIALS=y.
If CONFIG_DEBUG_CREDENTIALS=y, BUG() is called from __invalid_creds() because
cred->magic == 0. Failing that, BUG() is called from selinux_cred_free()
because selinux_cred_free() is not expecting cred->security == NULL. This does
not affect smack_cred_free(), tomoyo_cred_free() or apparmor_cred_free().
Fix these bugs by
(1) Set new->magic before calling security_cred_alloc_blank().
(2) Handle null cred->security in creds_are_invalid() and selinux_cred_free().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 51788b1bdd0d68345bab0af4301e7fa429277228 upstream.
Commit bf5fc093c5b625e4259203f1cee7ca73488a5620 refactored
btrfs_ioctl_space_info() and introduced several security issues.
space_args.space_slots is an unsigned 64-bit type controlled by a
possibly unprivileged caller. The comparison as a signed int type
allows providing values that are treated as negative and cause the
subsequent allocation size calculation to wrap, or be truncated to 0.
By providing a size that's truncated to 0, kmalloc() will return
ZERO_SIZE_PTR. It's also possible to provide a value smaller than the
slot count. The subsequent loop ignores the allocation size when
copying data in, resulting in a heap overflow or write to ZERO_SIZE_PTR.
The fix changes the slot count type and comparison typecast to u64,
which prevents truncation or signedness errors, and also ensures that we
don't copy more data than we've allocated in the subsequent loop. Note
that zero-size allocations are no longer possible since there is already
an explicit check for space_args.space_slots being 0 and truncation of
this value is no longer an issue.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Josef Bacik <josef@redhat.com>
Reviewed-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 78d2978874e4e10e97dfd4fd79db45bdc0748550 upstream.
In get_empty_filp() since 2.6.29, file_free(f) is called with f->f_cred == NULL
when security_file_alloc() returned an error. As a result, kernel will panic()
due to put_cred(NULL) call within RCU callback.
Fix this bug by assigning f->f_cred before calling security_file_alloc().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c64f6f934c7490faff76faf96217066a1b3570a0 upstream.
This device used the MULTI_INPUT quirk whereas it could be used
with hid-mosart instead to support the multitouch part.
Reference: https://bugs.launchpad.net/ubuntu/+bug/620609/
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bc5ab083a68bfec212780281f8e57d871d8882a0 upstream.
This device has been reported to be an hid-cando one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0fbca4d1c3932c27c4794bf5c2b5fc961cf5a54f upstream.
Commit 368e136 ("xfs: remove duplicate code from dquot reclaim") fails
to unlock the dquot freelist when the number of loop restarts is
exceeded in xfs_qm_dqreclaim_one(). This causes hangs in memory
reclaim.
Rework the loop control logic into an unwind stack that all the
different cases jump into. This means there is only one set of code
that processes the loop exit criteria, and simplifies the unlocking
of all the items from different points in the loop. It also fixes a
double increment of the restart counter from the qi_dqlist_lock
case.
Reported-by: Malcolm Scott <lkml@malc.org.uk>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
