| Age | Commit message (Collapse) | Author |
|---|
|
|
|
commit d7824370e26325c881b665350ce64fb0a4fde24a upstream.
This commit makes the stack guard page somewhat less visible to user
space. It does this by:
- not showing the guard page in /proc/<pid>/maps
It looks like lvm-tools will actually read /proc/self/maps to figure
out where all its mappings are, and effectively do a specialized
"mlockall()" in user space. By not showing the guard page as part of
the mapping (by just adding PAGE_SIZE to the start for grows-up
pages), lvm-tools ends up not being aware of it.
- by also teaching the _real_ mlock() functionality not to try to lock
the guard page.
That would just expand the mapping down to create a new guard page,
so there really is no point in trying to lock it in place.
It would perhaps be nice to show the guard page specially in
/proc/<pid>/maps (or at least mark grow-down segments some way), but
let's not open ourselves up to more breakage by user space from programs
that depends on the exact deails of the 'maps' file.
Special thanks to Henrique de Moraes Holschuh for diving into lvm-tools
source code to see what was going on with the whole new warning.
[Note, for .27, only the /proc change is done, mlock is not modified
here. - gregkh]
Reported-and-tested-by: François Valenduc <francois.valenduc@tvcablenet.be
Reported-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 11ac552477e32835cb6970bf0a70c210807f5673 upstream.
We do in fact need to unmap the page table _before_ doing the whole
stack guard page logic, because if it is needed (mainly 32-bit x86 with
PAE and CONFIG_HIGHPTE, but other architectures may use it too) then it
will do a kmap_atomic/kunmap_atomic.
And those kmaps will create an atomic region that we cannot do
allocations in. However, the whole stack expand code will need to do
anon_vma_prepare() and vma_lock_anon_vma() and they cannot do that in an
atomic region.
Now, a better model might actually be to do the anon_vma_prepare() when
_creating_ a VM_GROWSDOWN segment, and not have to worry about any of
this at page fault time. But in the meantime, this is the
straightforward fix for the issue.
See https://bugzilla.kernel.org/show_bug.cgi?id=16588 for details.
Reported-by: Wylda <wylda@volny.cz>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Reported-by: Mike Pagano <mpagano@gentoo.org>
Reported-by: François Valenduc <francois.valenduc@tvcablenet.be>
Tested-by: Ed Tomlinson <edt@aei.ca>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 05fa199d45c54a9bda7aa3ae6537253d6f097aa9 upstream.
Tetsuo Handa reports seeing the WARN_ON(current->mm == NULL) in
security_vm_enough_memory(), when do_execve() is touching the
target mm's stack, to set up its args and environment.
Yes, a UMH_NO_WAIT or UMH_WAIT_PROC call_usermodehelper() spawns
an mm-less kernel thread to do the exec. And in any case, that
vm_enough_memory check when growing stack ought to be done on the
target mm, not on the execer's mm (though apart from the warning,
it only makes a slight tweak to OVERCOMMIT_NEVER behaviour).
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Based on commit 96054569190bdec375fe824e48ca1f4e3b53dd36 upstream,
authored by Linus Torvalds.
This is my backport to the .27 kernel tree, hopefully preserving
the same functionality.
Original commit message:
It's wrong for several reasons, but the most direct one is that the
fault may be for the stack accesses to set up a previous SIGBUS. When
we have a kernel exception, the kernel exception handler does all the
fixups, not some user-level signal handler.
Even apart from the nested SIGBUS issue, it's also wrong to give out
kernel fault addresses in the signal handler info block, or to send a
SIGBUS when a system call already returns EFAULT.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5528f9132cf65d4d892bcbc5684c61e7822b21e9 upstream.
.. which didn't show up in my tests because it's a no-op on x86-64 and
most other architectures. But we enter the function with the last-level
page table mapped, and should unmap it at exit.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 320b2b8de12698082609ebbc1a17165727f4c893 upstream.
This is a rather minimally invasive patch to solve the problem of the
user stack growing into a memory mapped area below it. Whenever we fill
the first page of the stack segment, expand the segment down by one
page.
Now, admittedly some odd application might _want_ the stack to grow down
into the preceding memory mapping, and so we may at some point need to
make this a process tunable (some people might also want to have more
than a single page of guarding), but let's try the minimal approach
first.
Tested with trivial application that maps a single page just below the
stack, and then starts recursing. Without this, we will get a SIGSEGV
_after_ the stack has smashed the mapping. With this patch, we'll get a
nice SIGBUS just as the stack touches the page just above the mapping.
Requested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
commit 69fc208be5b7eb18d22d1eca185b201400fd5ffc upstream.
On second thoughts, this is just going to disturb people while telling us
things which we already knew.
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f1d0b063d993527754f062c589b73f125024d216 upstream.
Devices which share the same queue, like floppies and mtd devices, get
registered multiple times in the bdi interface, but bdi accounts only the
last registered device of the devices sharing one queue.
On remove, all earlier registered devices leak, stay around in sysfs, and
cause "duplicate filename" errors if the devices are re-created.
This prevents the creation of multiple bdi interfaces per queue, and the
bdi device will carry the dev_t name of the block device which is the
first one registered, of the pool of devices using the same queue.
[akpm@linux-foundation.org: add a WARN_ON so we know which drivers are misbehaving]
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8a22b9996b001c88f2bfb54c6de6a05fc39e177a upstream.
xen_sched_clock only counts unstolen time. In principle this should
be useful to the Linux scheduler so that it knows how much time a process
actually consumed. But in practice this doesn't work very well as the
scheduler expects the sched_clock time to be synchronized between
cpus. It also uses sched_clock to measure the time a task spends
sleeping, in which case "unstolen time" isn't meaningful.
So just use plain xen_clocksource_read to return wallclock nanoseconds
for sched_clock.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit aca0fa34bdaba39bfddddba8ca70dba4782e8fe6 upstream.
It's currently possible to bypass xattr namespace access rules by
prefixing valid xattr names with "os2.", since the os2 namespace stores
extended attributes in a legacy format with no prefix.
This patch adds checking to deny access to any valid namespace prefix
following "os2.".
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Reported-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a2a20c412c86e0bb46a9ab0dd31bcfe6d201b913 upstream.
If signalfd is used to consume a signal generated by a POSIX interval
timer or POSIX message queue, the ssi_int field does not reflect the data
(sigevent->sigev_value) supplied to timer_create(2) or mq_notify(3). (The
ssi_ptr field, however, is filled in.)
This behavior differs from signalfd's treatment of sigqueue-generated
signals -- see the default case in signalfd_copyinfo. It also gives
results that differ from the case when a signal is handled conventionally
via a sigaction-registered handler.
So, set signalfd_siginfo->ssi_int in the remaining cases (__SI_TIMER,
__SI_MESGQ) where ssi_ptr is set.
akpm: a non-back-compatible change. Merge into -stable to minimise the
number of kernels which are in the field and which miss this feature.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ceeab92971e8af05c1e81a4ff2c271124b55bb9b upstream.
The comments in the code indicate that file_info should be released if the
function fails. This releasing is done at the label out_free, not out.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = kmem_cache_zalloc(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return <+...x...+>;
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmem_cache_zalloc %s" % (p1[0].file,p1[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c43f7b8fb03be8bcc579bfc4e6ab70eac887ab55 upstream.
Lower filesystems that only implemented unlocked_ioctl weren't being
passed ioctl calls because eCryptfs only checked for
lower_file->f_op->ioctl and returned -ENOTTY if it was NULL.
eCryptfs shouldn't implement ioctl(), since it doesn't require the BKL.
This patch introduces ecryptfs_unlocked_ioctl() and
ecryptfs_compat_ioctl(), which passes the calls on to the lower file
system.
https://bugs.launchpad.net/ecryptfs/+bug/469664
Reported-by: James Dupin <james.dupin@gmail.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 51e9ac77035a3dfcb6fc0a88a0d80b6f99b5edb1 upstream.
If the 'bio_split' path in raid10-read is used while
resync/recovery is happening it is possible to deadlock.
Fix this be elevating ->nr_waiting for the duration of both
parts of the split request.
This fixes a bug that has been present since 2.6.22
but has only started manifesting recently for unknown reasons.
It is suitable for and -stable since then.
Reported-by: Justin Bronder <jsbronder@gentoo.org>
Tested-by: Justin Bronder <jsbronder@gentoo.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 549e15611b4ac1de51ef0e0a79c2704f50a638a2 upstream.
MSI delivery from on-board ahci controller doesn't work on K8M800. At
this point, it's unclear whether the culprit is with the ahci
controller or the host bridge. Given the track record and considering
the rather minimal impact of MSI, disabling it seems reasonable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rainer Hurtado Navarro <publio.escipion.el.africano@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6965031d331a642e31278fa1b5bd47f372ffdd5d upstream.
SPLICE_F_NONBLOCK is clearly documented to only affect blocking on the
pipe. In __generic_file_splice_read(), however, it causes an EAGAIN
if the page is currently being read.
This makes it impossible to write an application that only wants
failure if the pipe is full. For example if the same process is
handling both ends of a pipe and isn't otherwise able to determine
whether a splice to the pipe will fill it or not.
We could make the read non-blocking on O_NONBLOCK or some other splice
flag, but for now this is the simplest fix.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a01c7800420d2c294ca403988488a635d4087a6d upstream.
In nvram_write, first of all, correctly handle the case where the file
pointer is already beyond the end; we should return EOF in that case.
Second, make the logic a bit more explicit so that gcc can statically
prove that the copy_from_user() is safe. Once the condition of the
beyond-end filepointer is eliminated, the copy is safe but gcc can't
prove it, causing build failures for i386 allyesconfig.
Third, eliminate the entirely superfluous variable "len", and just use
the passed-in variable "count" instead.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <tip-*@git.kernel.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
commit 728a756b8fcd22d80e2dbba8117a8a3aafd3f203 upstream.
This patch fixes a kernel Oops in the GFS2 rename code.
The problem was in the way the gfs2 directory code was trying
to re-use sentinel directory entries.
In the failing case, gfs2's rename function was renaming a
file to another name that had the same non-trivial length.
The file being renamed happened to be the first directory
entry on the leaf block.
First, the rename code (gfs2_rename in ops_inode.c) found the
original directory entry and decided it could do its job by
simply replacing the directory entry with another. Therefore
it determined correctly that no block allocations were needed.
Next, the rename code deleted the old directory entry prior to
replacing it with the new name. Therefore, the soon-to-be
replaced directory entry was temporarily made into a directory
entry "sentinel" or a place holder at the start of a leaf block.
Lastly, it went to re-add the replacement directory entry in
that leaf block. However, when gfs2_dirent_find_space was
looking for space in the leaf block, it used the wrong value
for the sentinel. That threw off its calculations so later
it decides it can't really re-use the sentinel and therefore
must allocate a new leaf block. But because it previously decided
to re-use the directory entry, it didn't waste the time to
grab a new block allocation for the inode. Therefore, the
inode's i_alloc pointer was still NULL and it crashes trying to
reference it.
In the case of sentinel directory entries, the entire dirent is
reused, not just the "free space" portion of it, and therefore
the function gfs2_dirent_find_space should use the value 0
rather than GFS2_DIRENT_SIZE(0) for the actual dirent size.
Fixing this calculation enables the reproducer programs to work
properly.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a91c1be21704113b023919826c6d531da46656ef upstream.
we also need to clean up and free the cdev.
Reported-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1817176a86352f65210139d4c794ad2d19fc6b63 upstream.
This patch prevents user "foo" from using the SWAPEXT ioctl to swap
a write-only file owned by user "bar" into a file owned by "foo" and
subsequently reading it. It does so by checking that the file
descriptors passed to the ioctl are also opened for reading.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4b4fd27c0b5ec638a1f06ced9226fd95229dbbf0 upstream.
avoid potential stack overflow by correctly checking count parameter
Reported-by: Ilja <ilja@netric.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c17dad6905fc82d8f523399e5c3f014e81d61df6 upstream.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
commit a6f80fb7b5986fda663d94079d3bba0937a6b6ff upstream.
The function ecryptfs_uid_hash wrongly assumes that the
second parameter to hash_long() is the number of hash
buckets instead of the number of hash bits.
This patch fixes that and renames the variable
ecryptfs_hash_buckets to ecryptfs_hash_bits to make it
clearer.
Fixes: CVE-2010-2492
Signed-off-by: Andre Osterhues <aosterhues@escrypt.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1c938663d58b5b2965976a6f54cc51b5d6f691aa upstream.
Alan <alan@clueserver.org> writes:
> program: /home/alan/GitTrees/linux-2.6-mid-ref/scripts/mod/modpost -o
> Module.symvers -S vmlinux.o
>
> Program received signal SIGSEGV, Segmentation fault.
It just hit me.
It's the offset calculation in reloc_location() which overflows:
return (void *)elf->hdr + sechdrs[section].sh_offset +
(r->r_offset - sechdrs[section].sh_addr);
E.g. for the first rodata r entry:
r->r_offset < sechdrs[section].sh_addr
and the expression in the parenthesis produces 0xFFFFFFE0 or something
equally wise.
Reported-by: Alan <alan@clueserver.org>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Tested-by: Alan <alan@clueserver.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5a29f7893fbe681f1334285be7e41e56f0de666c upstream.
I've hit an issue on my system when I've been using RealTek RTL8139D cards in
bonding interface in mode balancing-alb. When I enslave a card, the current
active slave (bond->curr_active_slave) is not set and the link is therefore
not functional.
----
# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: None
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:1f:1f:01:2f:22
----
The thing that gets it right is when I unplug the cable and then I put it back
into the NIC. Then the current active slave is set to eth1 and link is working
just fine. Here is dmesg log with bonding DEBUG messages turned on:
----
ADDRCONF(NETDEV_UP): bond0: link is not ready
event_dev: bond0, event: 1
IFF_MASTER
event_dev: bond0, event: 8
IFF_MASTER
bond_ioctl: master=bond0, cmd=35216
slave_dev=cac5d800:
slave_dev->name=eth1:
eth1: ! NETIF_F_VLAN_CHALLENGED
event_dev: eth1, event: 8
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 1
event_dev: eth1, event: 8
IFF_SLAVE
Initial state of slave_dev is BOND_LINK_UP
bonding: bond0: enslaving eth1 as an active interface with an up link.
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
event_dev: bond0, event: 4
IFF_MASTER
bond0: no IPv6 routers present
<<<<cable unplug>>>>
eth1: link down
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely down for interface eth1, disabling it
event_dev: bond0, event: 4
IFF_MASTER
<<<<cable plug>>>>
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
event_dev: eth1, event: 8
IFF_SLAVE
event_dev: eth1, event: 8
IFF_SLAVE
bonding: bond0: first active interface up!
event_dev: bond0, event: 4
IFF_MASTER
----
The current active slave is set by calling bond_select_active_slave() function
from bond_miimon_commit() function when the slave (eth1) link goes to state up.
I also tested this on other machine with Broadcom NetXtreme II BCM5708
1000Base-T NIC and there all works fine. The thing is that this adapter is down
and goes up after few seconds after it is enslaved.
This patch calls bond_select_active_slave() in bond_enslave() function for modes
alb and tlb and makes sure that the current active slave is set up properly even
when the slave state is already up. Tested on both systems, works fine.
Notice: The same problem can maybe also occrur in mode 8023AD but I'm unable to
test that.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7a52b34b07122ff5f45258d47f260f8a525518f0 upstream.
Sumeet Lahorani <sumeet.lahorani@oracle.com> reported that the IPoIB
child entries are world-writable; however we don't want ordinary users
to be able to create and destroy child interfaces, so fix them to be
writable only by root.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d596043d71ff0d7b3d0bead19b1d68c55f003093 upstream.
The x3950 family can have as many as 256 PCI buses in a single system, so
change the limits to the maximum. Since there can only be 256 PCI buses in one
domain, we no longer need the BUG_ON check.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
LKML-Reference: <20100701004519.GQ15515@tux1.beaverton.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 499a00e92dd9a75395081f595e681629eb1eebad upstream.
Newer systems (x3950M2) can have 48 PHBs per chassis and 8
chassis, so bump the limits up and provide an explanation
of the requirements for each class.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Corinna Schultz <cschultz@linux.vnet.ibm.com>
LKML-Reference: <20100624212647.GI15515@tux1.beaverton.ibm.com>
[ v2: Fixed build bug, added back PHBS_PER_CALGARY == 4 ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6fd024893911dcb51b4a0aa71971db5ba38f7071 upstream.
The current initialisation code probes 'unsupported' AGP devices
simply by calling its own probe function. It does not lock these
devices or even check whether another driver is already bound to
them.
We must use the device core to manage this. So if the specific
device id table didn't match anything and agp_try_unsupported=1,
switch the device id table and call driver_attach() again.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8a52da632ceb9d8b776494563df579e87b7b586b upstream.
The debugging code using the freed structure is moved before the kfree.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@free@
expression E;
position p;
@@
kfree@p(E)
@@
expression free.E, subE<=free.E, E1;
position free.p;
@@
kfree@p(E)
...
(
subE = E1
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
commit 499031ac8a3df6738f6186ded9da853e8ea18253 upstream.
We should release dst if dst->error is set.
Bug introduced in 2.6.14 by commit e104411b82f5c
([XFRM]: Always release dst_entry on error in xfrm_lookup)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d6a574ff6bfb842bdb98065da053881ff527be46 upstream.
Use an irq spinlock to hold off the IRQ handler until
enough early card init is complete such that the handler
can run without faulting.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f8324e20f8289dffc646d64366332e05eaacab25 upstream.
The kernel's math-emu code contains a macro _FP_FROM_INT() which is
used to convert an integer to a raw normalized floating-point value.
It does this basically in three steps:
1. Compute the exponent from the number of leading zero bits.
2. Downshift large fractions to put the MSB in the right position
for normalized fractions.
3. Upshift small fractions to put the MSB in the right position.
There is an boundary error in step 2, causing a fraction with its
MSB exactly one bit above the normalized MSB position to not be
downshifted. This results in a non-normalized raw float, which when
packed becomes a massively inaccurate representation for that input.
The impact of this depends on a number of arch-specific factors,
but it is known to have broken emulation of FXTOD instructions
on UltraSPARC III, which was originally reported as GCC bug 44631
<http://gcc.gnu.org/bugzilla/show_bug.cgi?id=44631>.
Any arch which uses math-emu to emulate conversions from integers to
same-size floats may be affected.
The fix is simple: the exponent comparison used to determine if the
fraction should be downshifted must be "<=" not "<".
I'm sending a kernel module to test this as a reply to this message.
There are also SPARC user-space test cases in the GCC bug entry.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 38000a94a902e94ca8b5498f7871c6316de8957a upstream.
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ed770f01360b392564650bf1553ce723fa46afec upstream.
If the call to phy_connect fails, we will return directly instead of freeing
the previously allocated struct net_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6513a81e9325d712f1bfb9a1d7b750134e49ff18 upstream.
While chasing a bug report involving a OS/2 server, I noticed the server sets
pSMBr->CountHigh to a incorrect value even in case of normal writes. This
results in 'nbytes' being computed wrongly and triggers a kernel BUG at
mm/filemap.c.
void iov_iter_advance(struct iov_iter *i, size_t bytes)
{
BUG_ON(i->count < bytes); <--- BUG here
Why the server is setting 'CountHigh' is not clear but only does so after
writing 64k bytes. Though this looks like the server bug, the client side
crash may not be acceptable.
The workaround is to mask off high 16 bits if the number of bytes written as
returned by the server is greater than the bytes requested by the client as
suggested by Jeff Layton.
Reviewed-by: Jeff Layton <jlayton@samba.org>
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8a224d489454b7457105848610cfebebdec5638d upstream.
This bug appears to be the result of a cut-and-paste mistake from the
NTLMv1 code. The function to generate the MAC key was commented out, but
not the conditional above it. The conditional then ended up causing the
session setup key not to be copied to the buffer unless this was the
first session on the socket, and that made all but the first NTLMv2
session setup fail.
Fix this by removing the conditional and all of the commented clutter
that made it difficult to see.
Reported-by: Gunther Deschner <gdeschne@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d883b9f0977269d519469da72faec6a7f72cb489 upstream.
On hyper-threaded CPUs, each core appears twice in the CPU list. Skip
the second entry to avoid duplicate sensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3f4f09b4be35d38d6e2bf22c989443e65e70fc4c upstream.
Don't assume that CPU entry number and core ID always match. It
worked in the simple cases (single CPU, no HT) but fails on
multi-CPU systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
commit 2e3219b5c8a2e44e0b83ae6e04f52f20a82ac0f2 upstream.
commit 5fa782c2f5ef6c2e4f04d3e228412c9b4a4c8809
sctp: Fix skb_over_panic resulting from multiple invalid \
parameter errors (CVE-2010-1173) (v4)
cause 'error cause' never be add the the ERROR chunk due to
some typo when check valid length in sctp_init_cause_fixed().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cea7daa3589d6b550546a8c8963599f7c1a3ae5c upstream.
find_keyring_by_name() can gain access to a keyring that has had its reference
count reduced to zero, and is thus ready to be freed. This then allows the
dead keyring to be brought back into use whilst it is being destroyed.
The following timeline illustrates the process:
|(cleaner) (user)
|
| free_user(user) sys_keyctl()
| | |
| key_put(user->session_keyring) keyctl_get_keyring_ID()
| || //=> keyring->usage = 0 |
| |schedule_work(&key_cleanup_task) lookup_user_key()
| || |
| kmem_cache_free(,user) |
| . |[KEY_SPEC_USER_KEYRING]
| . install_user_keyrings()
| . ||
| key_cleanup() [<= worker_thread()] ||
| | ||
| [spin_lock(&key_serial_lock)] |[mutex_lock(&key_user_keyr..mutex)]
| | ||
| atomic_read() == 0 ||
| |{ rb_ease(&key->serial_node,) } ||
| | ||
| [spin_unlock(&key_serial_lock)] |find_keyring_by_name()
| | |||
| keyring_destroy(keyring) ||[read_lock(&keyring_name_lock)]
| || |||
| |[write_lock(&keyring_name_lock)] ||atomic_inc(&keyring->usage)
| |. ||| *** GET freeing keyring ***
| |. ||[read_unlock(&keyring_name_lock)]
| || ||
| |list_del() |[mutex_unlock(&key_user_k..mutex)]
| || |
| |[write_unlock(&keyring_name_lock)] ** INVALID keyring is returned **
| | .
| kmem_cache_free(,keyring) .
| .
| atomic_dec(&keyring->usage)
v *** DESTROYED ***
TIME
If CONFIG_SLUB_DEBUG=y then we may see the following message generated:
=============================================================================
BUG key_jar: Poison overwritten
-----------------------------------------------------------------------------
INFO: 0xffff880197a7e200-0xffff880197a7e200. First byte 0x6a instead of 0x6b
INFO: Allocated in key_alloc+0x10b/0x35f age=25 cpu=1 pid=5086
INFO: Freed in key_cleanup+0xd0/0xd5 age=12 cpu=1 pid=10
INFO: Slab 0xffffea000592cb90 objects=16 used=2 fp=0xffff880197a7e200 flags=0x200000000000c3
INFO: Object 0xffff880197a7e200 @offset=512 fp=0xffff880197a7e300
Bytes b4 0xffff880197a7e1f0: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Object 0xffff880197a7e200: 6a 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b jkkkkkkkkkkkkkkk
Alternatively, we may see a system panic happen, such as:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000001
IP: [<ffffffff810e61a3>] kmem_cache_alloc+0x5b/0xe9
PGD 6b2b4067 PUD 6a80d067 PMD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/kernel/kexec_crash_loaded
CPU 1
...
Pid: 31245, comm: su Not tainted 2.6.34-rc5-nofixed-nodebug #2 D2089/PRIMERGY
RIP: 0010:[<ffffffff810e61a3>] [<ffffffff810e61a3>] kmem_cache_alloc+0x5b/0xe9
RSP: 0018:ffff88006af3bd98 EFLAGS: 00010002
RAX: 0000000000000000 RBX: 0000000000000001 RCX: ffff88007d19900b
RDX: 0000000100000000 RSI: 00000000000080d0 RDI: ffffffff81828430
RBP: ffffffff81828430 R08: ffff88000a293750 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000100000 R12: 00000000000080d0
R13: 00000000000080d0 R14: 0000000000000296 R15: ffffffff810f20ce
FS: 00007f97116bc700(0000) GS:ffff88000a280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000001 CR3: 000000006a91c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process su (pid: 31245, threadinfo ffff88006af3a000, task ffff8800374414c0)
Stack:
0000000512e0958e 0000000000008000 ffff880037f8d180 0000000000000001
0000000000000000 0000000000008001 ffff88007d199000 ffffffff810f20ce
0000000000008000 ffff88006af3be48 0000000000000024 ffffffff810face3
Call Trace:
[<ffffffff810f20ce>] ? get_empty_filp+0x70/0x12f
[<ffffffff810face3>] ? do_filp_open+0x145/0x590
[<ffffffff810ce208>] ? tlb_finish_mmu+0x2a/0x33
[<ffffffff810ce43c>] ? unmap_region+0xd3/0xe2
[<ffffffff810e4393>] ? virt_to_head_page+0x9/0x2d
[<ffffffff81103916>] ? alloc_fd+0x69/0x10e
[<ffffffff810ef4ed>] ? do_sys_open+0x56/0xfc
[<ffffffff81008a02>] ? system_call_fastpath+0x16/0x1b
Code: 0f 1f 44 00 00 49 89 c6 fa 66 0f 1f 44 00 00 65 4c 8b 04 25 60 e8 00 00 48 8b 45 00 49 01 c0 49 8b 18 48 85 db 74 0d 48 63 45 18 <48> 8b 04 03 49 89 00 eb 14 4c 89 f9 83 ca ff 44 89 e6 48 89 ef
RIP [<ffffffff810e61a3>] kmem_cache_alloc+0x5b/0xe9
This problem is that find_keyring_by_name does not confirm that the keyring is
valid before accepting it.
Skipping keyrings that have been reduced to a zero count seems the way to go.
To this end, use atomic_inc_not_zero() to increment the usage count and skip
the candidate keyring if that returns false.
The following script _may_ cause the bug to happen, but there's no guarantee
as the window of opportunity is small:
#!/bin/sh
LOOP=100000
USER=dummy_user
/bin/su -c "exit;" $USER || { /usr/sbin/adduser -m $USER; add=1; }
for ((i=0; i<LOOP; i++))
do
/bin/su -c "echo '$i' > /dev/null" $USER
done
(( add == 1 )) && /usr/sbin/userdel -r $USER
exit
Note that the nominated user must not be in use.
An alternative way of testing this may be:
for ((i=0; i<100000; i++))
do
keyctl session foo /bin/true || break
done >&/dev/null
as that uses a keyring named "foo" rather than relying on the user and
user-session named keyrings.
Reported-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4d09ec0f705cf88a12add029c058b53f288cfaa2 upstream.
We were using the wrong variable here so the error codes weren't being returned
properly. The original code returns -ENOKEY.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 550f0d922286556c7ea43974bb7921effb5a5278 upstream.
Clear the floating point exception flag before returning to
user space. This is needed, else the libc trampoline handler
may hit the same SIGFPE again while building up a trampoline
to a signal handler.
Fixes debian bug #559406.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d0021b252eaf65ca07ed14f0d66425dd9ccab9a6 upstream.
Fix TIPC to disallow sending to remote addresses prior to entering NET_MODE
user programs can oops the kernel by sending datagrams via AF_TIPC prior to
entering networked mode. The following backtrace has been observed:
ID: 13459 TASK: ffff810014640040 CPU: 0 COMMAND: "tipc-client"
[exception RIP: tipc_node_select_next_hop+90]
RIP: ffffffff8869d3c3 RSP: ffff81002d9a5ab8 RFLAGS: 00010202
RAX: 0000000000000001 RBX: 0000000000000001 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000001001001
RBP: 0000000001001001 R8: 0074736575716552 R9: 0000000000000000
R10: ffff81003fbd0680 R11: 00000000000000c8 R12: 0000000000000008
R13: 0000000000000001 R14: 0000000000000001 R15: ffff810015c6ca00
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
RIP: 0000003cbd8d49a3 RSP: 00007fffc84e0be8 RFLAGS: 00010206
RAX: 000000000000002c RBX: ffffffff8005d116 RCX: 0000000000000000
RDX: 0000000000000008 RSI: 00007fffc84e0c00 RDI: 0000000000000003
RBP: 0000000000000000 R8: 00007fffc84e0c10 R9: 0000000000000010
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffc84e0d10 R14: 0000000000000000 R15: 00007fffc84e0c30
ORIG_RAX: 000000000000002c CS: 0033 SS: 002b
What happens is that, when the tipc module in inserted it enters a standalone
node mode in which communication to its own address is allowed <0.0.0> but not
to other addresses, since the appropriate data structures have not been
allocated yet (specifically the tipc_net pointer). There is nothing stopping a
client from trying to send such a message however, and if that happens, we
attempt to dereference tipc_net.zones while the pointer is still NULL, and
explode. The fix is pretty straightforward. Since these oopses all arise from
the dereference of global pointers prior to their assignment to allocated
values, and since these allocations are small (about 2k total), lets convert
these pointers to static arrays of the appropriate size. All the accesses to
these bits consider 0/NULL to be a non match when searching, so all the lookups
still work properly, and there is no longer a chance of a bad dererence
anywhere. As a bonus, this lets us eliminate the setup/teardown routines for
those pointers, and elimnates the need to preform any locking around them to
prevent access while their being allocated/freed.
I've updated the tipc_net structure to behave this way to fix the exact reported
problem, and also fixed up the tipc_bearers and media_list arrays to fix an
obvious simmilar problem that arises from issuing tipc-config commands to
manipulate bearers/links prior to entering networked mode
I've tested this for a few hours by running the sanity tests and stress test
with the tipcutils suite, and nothing has fallen over. There have been a few
lockdep warnings, but those were there before, and can be addressed later, as
they didn't actually result in any deadlock.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Allan Stephens <allan.stephens@windriver.com>
CC: David S. Miller <davem@davemloft.net>
CC: tipc-discussion@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit db1f05bb85d7966b9176e293f3ceead1cb8b5d79 upstream.
Add a new UMOUNT_NOFOLLOW flag to umount(2). This is needed to prevent
symlink attacks in unprivileged unmounts (fuse, samba, ncpfs).
Additionally, return -EINVAL if an unknown flag is used (and specify
an explicitly unused flag: UMOUNT_UNUSED). This makes it possible for
the caller to determine if a flag is supported or not.
CC: Eugene Teo <eugene@redhat.com>
CC: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
