aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-07-17hwmon: (adm1029) Ensure the fan_div cache is updated in set_fan_divAxel Lin
commit 1035a9e3e9c76b64a860a774f5b867d28d34acc2 upstream. Writing to fanX_div does not clear the cache. As a result, reading from fanX_div may return the old value for up to two seconds after writing a new value. This patch ensures the fan_div cache is updated in set_fan_div(). Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17hwmon: (adm1031) Fix writes to limit registersGuenter Roeck
commit 145e74a4e5022225adb84f4e5d4fff7938475c35 upstream. Upper limit for write operations to temperature limit registers was clamped to a fractional value. However, limit registers do not support fractional values. As a result, upper limits of 127.5 degrees C or higher resulted in a rounded limit of 128 degrees C. Since limit registers are signed, this was stored as -128 degrees C. Clamp limits to (-55, +127) degrees C to solve the problem. Value on writes to auto_temp[12]_min and auto_temp[12]_max were not clamped at all, but masked. As a result, out-of-range writes resulted in a more or less arbitrary limit. Clamp those attributes to (0, 127) degrees C for more predictable results. Cc: Axel Lin <axel.lin@ingics.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17hwmon: (emc2103) Clamp limits instead of bailing outGuenter Roeck
commit f6c2dd20108c35e30e2c1f3c6142d189451a626b upstream. It is customary to clamp limits instead of bailing out with an error if a configured limit is out of the range supported by the driver. This simplifies limit configuration, since the user will not typically know chip and/or driver specific limits. Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17hwmon: (amc6821) Fix permissions for temp2_inputAxel Lin
commit df86754b746e9a0ff6f863f690b1c01d408e3cdc upstream. temp2_input should not be writable, fix it. Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17thermal: hwmon: Make the check for critical temp valid consistentAaron Lu
commit e8db5d6736a712a3e2280c0e31f4b301d85172d8 upstream. On 05/21/2014 04:22 PM, Aaron Lu wrote: > On 05/21/2014 01:57 PM, Kui Zhang wrote: >> Hello, >> >> I get following error when rmmod thermal. >> >> rmmod thermal >> Killed While dealing with this problem, I found another problem that also results in a kernel crash on thermal module removal: From: Aaron Lu <aaron.lu@intel.com> Date: Wed, 21 May 2014 16:05:38 +0800 Subject: thermal: hwmon: Make the check for critical temp valid consistent We used the tz->ops->get_crit_temp && !tz->ops->get_crit_temp(tz, temp) to decide if we need to create the temp_crit attribute file but we just check if tz->ops->get_crit_temp exists to decide if we need to remove that attribute file. Some ACPI thermal zone doesn't have a valid critical trip point and that would result in removing a non-existent device file on thermal module unload. Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17i8k: Fix non-SMP operationGuenter Roeck
commit 6d827fbcc370ca259a2905309f64161ab7b10596 upstream. Commit f36fdb9f0266 (i8k: Force SMM to run on CPU 0) adds support for multi-core CPUs to the driver. Unfortunately, that causes it to fail loading if compiled without SMP support, at least on 32 bit kernels. Kernel log shows "i8k: unable to get SMM Dell signature", and function i8k_smm is found to return -EINVAL. Testing revealed that the culprit is the missing return value check of set_cpus_allowed_ptr. Fixes: f36fdb9f0266 (i8k: Force SMM to run on CPU 0) Reported-by: Jim Bos <jim876@xs4all.nl> Tested-by: Jim Bos <jim876@xs4all.nl> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: Andreas Mohr <andi@lisas.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17workqueue: zero cpumask of wq_numa_possible_cpumask on initYasuaki Ishimatsu
commit 5a6024f1604eef119cf3a6fa413fe0261a81a8f3 upstream. When hot-adding and onlining CPU, kernel panic occurs, showing following call trace. BUG: unable to handle kernel paging request at 0000000000001d08 IP: [<ffffffff8114acfd>] __alloc_pages_nodemask+0x9d/0xb10 PGD 0 Oops: 0000 [#1] SMP ... Call Trace: [<ffffffff812b8745>] ? cpumask_next_and+0x35/0x50 [<ffffffff810a3283>] ? find_busiest_group+0x113/0x8f0 [<ffffffff81193bc9>] ? deactivate_slab+0x349/0x3c0 [<ffffffff811926f1>] new_slab+0x91/0x300 [<ffffffff815de95a>] __slab_alloc+0x2bb/0x482 [<ffffffff8105bc1c>] ? copy_process.part.25+0xfc/0x14c0 [<ffffffff810a3c78>] ? load_balance+0x218/0x890 [<ffffffff8101a679>] ? sched_clock+0x9/0x10 [<ffffffff81105ba9>] ? trace_clock_local+0x9/0x10 [<ffffffff81193d1c>] kmem_cache_alloc_node+0x8c/0x200 [<ffffffff8105bc1c>] copy_process.part.25+0xfc/0x14c0 [<ffffffff81114d0d>] ? trace_buffer_unlock_commit+0x4d/0x60 [<ffffffff81085a80>] ? kthread_create_on_node+0x140/0x140 [<ffffffff8105d0ec>] do_fork+0xbc/0x360 [<ffffffff8105d3b6>] kernel_thread+0x26/0x30 [<ffffffff81086652>] kthreadd+0x2c2/0x300 [<ffffffff81086390>] ? kthread_create_on_cpu+0x60/0x60 [<ffffffff815f20ec>] ret_from_fork+0x7c/0xb0 [<ffffffff81086390>] ? kthread_create_on_cpu+0x60/0x60 In my investigation, I found the root cause is wq_numa_possible_cpumask. All entries of wq_numa_possible_cpumask is allocated by alloc_cpumask_var_node(). And these entries are used without initializing. So these entries have wrong value. When hot-adding and onlining CPU, wq_update_unbound_numa() is called. wq_update_unbound_numa() calls alloc_unbound_pwq(). And alloc_unbound_pwq() calls get_unbound_pool(). In get_unbound_pool(), worker_pool->node is set as follow: 3592 /* if cpumask is contained inside a NUMA node, we belong to that node */ 3593 if (wq_numa_enabled) { 3594 for_each_node(node) { 3595 if (cpumask_subset(pool->attrs->cpumask, 3596 wq_numa_possible_cpumask[node])) { 3597 pool->node = node; 3598 break; 3599 } 3600 } 3601 } But wq_numa_possible_cpumask[node] does not have correct cpumask. So, wrong node is selected. As a result, kernel panic occurs. By this patch, all entries of wq_numa_possible_cpumask are allocated by zalloc_cpumask_var_node to initialize them. And the panic disappeared. Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Reviewed-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: bce903809ab3 ("workqueue: add wq_numa_tbl_len and wq_numa_possible_cpumask[]") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17cpuset,mempolicy: fix sleeping function called from invalid contextGu Zheng
commit 391acf970d21219a2a5446282d3b20eace0c0d7a upstream. When runing with the kernel(3.15-rc7+), the follow bug occurs: [ 9969.258987] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:586 [ 9969.359906] in_atomic(): 1, irqs_disabled(): 0, pid: 160655, name: python [ 9969.441175] INFO: lockdep is turned off. [ 9969.488184] CPU: 26 PID: 160655 Comm: python Tainted: G A 3.15.0-rc7+ #85 [ 9969.581032] Hardware name: FUJITSU-SV PRIMEQUEST 1800E/SB, BIOS PRIMEQUEST 1000 Series BIOS Version 1.39 11/16/2012 [ 9969.706052] ffffffff81a20e60 ffff8803e941fbd0 ffffffff8162f523 ffff8803e941fd18 [ 9969.795323] ffff8803e941fbe0 ffffffff8109995a ffff8803e941fc58 ffffffff81633e6c [ 9969.884710] ffffffff811ba5dc ffff880405c6b480 ffff88041fdd90a0 0000000000002000 [ 9969.974071] Call Trace: [ 9970.003403] [<ffffffff8162f523>] dump_stack+0x4d/0x66 [ 9970.065074] [<ffffffff8109995a>] __might_sleep+0xfa/0x130 [ 9970.130743] [<ffffffff81633e6c>] mutex_lock_nested+0x3c/0x4f0 [ 9970.200638] [<ffffffff811ba5dc>] ? kmem_cache_alloc+0x1bc/0x210 [ 9970.272610] [<ffffffff81105807>] cpuset_mems_allowed+0x27/0x140 [ 9970.344584] [<ffffffff811b1303>] ? __mpol_dup+0x63/0x150 [ 9970.409282] [<ffffffff811b1385>] __mpol_dup+0xe5/0x150 [ 9970.471897] [<ffffffff811b1303>] ? __mpol_dup+0x63/0x150 [ 9970.536585] [<ffffffff81068c86>] ? copy_process.part.23+0x606/0x1d40 [ 9970.613763] [<ffffffff810bf28d>] ? trace_hardirqs_on+0xd/0x10 [ 9970.683660] [<ffffffff810ddddf>] ? monotonic_to_bootbased+0x2f/0x50 [ 9970.759795] [<ffffffff81068cf0>] copy_process.part.23+0x670/0x1d40 [ 9970.834885] [<ffffffff8106a598>] do_fork+0xd8/0x380 [ 9970.894375] [<ffffffff81110e4c>] ? __audit_syscall_entry+0x9c/0xf0 [ 9970.969470] [<ffffffff8106a8c6>] SyS_clone+0x16/0x20 [ 9971.030011] [<ffffffff81642009>] stub_clone+0x69/0x90 [ 9971.091573] [<ffffffff81641c29>] ? system_call_fastpath+0x16/0x1b The cause is that cpuset_mems_allowed() try to take mutex_lock(&callback_mutex) under the rcu_read_lock(which was hold in __mpol_dup()). And in cpuset_mems_allowed(), the access to cpuset is under rcu_read_lock, so in __mpol_dup, we can reduce the rcu_read_lock protection region to protect the access to cpuset only in current_cpuset_is_being_rebound(). So that we can avoid this bug. This patch is a temporary solution that just addresses the bug mentioned above, can not fix the long-standing issue about cpuset.mems rebinding on fork(): "When the forker's task_struct is duplicated (which includes ->mems_allowed) and it races with an update to cpuset_being_rebound in update_tasks_nodemask() then the task's mems_allowed doesn't get updated. And the child task's mems_allowed can be wrong if the cpuset's nodemask changes before the child has been added to the cgroup's tasklist." Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Acked-by: Li Zefan <lizefan@huawei.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17workqueue: fix dev_set_uevent_suppress() imbalanceMaxime Bizon
commit bddbceb688c6d0decaabc7884fede319d02f96c8 upstream. Uevents are suppressed during attributes registration, but never restored, so kobject_uevent() does nothing. Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: 226223ab3c4118ddd10688cc2c131135848371ab Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17parisc,metag: Do not hardcode maximum userspace stack sizeHelge Deller
commit 042d27acb64924a0e8a43e972485913a32407beb upstream. This patch affects only architectures where the stack grows upwards (currently parisc and metag only). On those do not hardcode the maximum initial stack size to 1GB for 32-bit processes, but make it configurable via a config option. The main problem with the hardcoded stack size is, that we have two memory regions which grow upwards: stack and heap. To keep most of the memory available for heap in a flexmap memory layout, it makes no sense to hard allocate up to 1GB of the memory for stack which can't be used as heap then. This patch makes the stack size for 32-bit processes configurable and uses 80MB as default value which has been in use during the last few years on parisc and which hasn't showed any problems yet. Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: linux-parisc@vger.kernel.org Cc: linux-metag@vger.kernel.org Cc: John David Anglin <dave.anglin@bell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17parisc: fix fanotify_mark() syscall on 32bit compat kernelHelge Deller
commit ab8a261ba5e2dd9206da640de5870cc31d568a7c upstream. On parisc we can not use the existing compat implementation for fanotify_mark() because for the 64bit mask parameter the higher and lower 32bits are ordered differently than what the compat function expects from big endian architectures. Specifically: It finally turned out, that on hppa we end up with different assignments of parameters to kernel arguments depending on if we call the glibc wrapper function int fanotify_mark (int __fanotify_fd, unsigned int __flags, uint64_t __mask, int __dfd, const char *__pathname); or directly calling the syscall manually syscall(__NR_fanotify_mark, ...) Reason is, that the syscall() function is implemented as C-function and because we now have the sysno as first parameter in front of the other parameters the compiler will unexpectedly add an empty paramenter in front of the u64 value to ensure the correct calling alignment for 64bit values. This means, on hppa you can't simply use syscall() to call the kernel fanotify_mark() function directly, but you have to use the glibc function instead. This patch fixes the kernel in the hppa-arch specifc coding to adjust the parameters in a way as if userspace calls the glibc wrapper function fanotify_mark(). Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17parisc: add serial ports of C8000/1GHz machine to hardware databaseHelge Deller
commit eadcc7208a2237016be7bdff4551ba7614da85c8 upstream. Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17iio: ti_am335x_adc: Fix: Use same step id at FIFOs both endsJan Kardell
commit baa3c65298c089a9014b4e523a14ec2885cca1bc upstream. Since AI lines could be selected at will (linux-3.11) the sending and receiving ends of the FIFO does not agree about what step is used for a line. It only works if the last lines are used, like 5,6,7, and fails if ie 2,4,6 is selected in DT. Signed-off-by: Jan Kardell <jan.kardell@telliq.com> Tested-by: Zubair Lutfullah <zubair.lutfullah@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17USB: serial: ftdi_sio: Add Infineon TriboardMichal Sojka
commit d8279a40e50ad55539780aa617a32a53d7f0953e upstream. This adds support for Infineon TriBoard TC1798 [1]. Only interface 1 is used as serial line (see [2], Figure 8-6). [1] http://www.infineon.com/cms/de/product/microcontroller/development-tools-software-and-kits/tricore-tm-development-tools-software-and-kits/starterkits-and-evaluation-boards/starter-kit-tc1798/channel.html?channel=db3a304333b8a7ca0133cfa3d73e4268 [2] http://www.infineon.com/dgdl/TriBoardManual-TC1798-V10.pdf?folderId=db3a304412b407950112b409ae7c0343&fileId=db3a304333b8a7ca0133cfae99fe426a Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz> Cc: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17USB: ftdi_sio: Add extra PID.Bert Vermeulen
commit 5a7fbe7e9ea0b1b9d7ffdba64db1faa3a259164c upstream. This patch adds PID 0x0003 to the VID 0x128d (Testo). At least the Testo 435-4 uses this, likely other gear as well. Signed-off-by: Bert Vermeulen <bert@biot.com> Cc: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17USB: cp210x: add support for Corsair usb dongleAndras Kovacs
commit b9326057a3d8447f5d2e74a7b521ccf21add2ec0 upstream. Corsair USB Dongles are shipped with Corsair AXi series PSUs. These are cp210x serial usb devices, so make driver detect these. I have a program, that can get information from these PSUs. Tested with 2 different dongles shipped with Corsair AX860i and AX1200i units. Signed-off-by: Andras Kovacs <andras@sth.sze.hu> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17usb: option: Add ID for Telewell TW-LTE 4G v2Bernd Wachter
commit 3d28bd840b2d3981cd28caf5fe1df38f1344dd60 upstream. Add ID of the Telewell 4G v2 hardware to option driver to get legacy serial interface working Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09Linux 3.14.12v3.14.12Greg Kroah-Hartman
2014-07-09mm: fix crashes from mbind() merging vmasHugh Dickins
commit d05f0cdcbe6388723f1900c549b4850360545201 upstream. In v2.6.34 commit 9d8cebd4bcd7 ("mm: fix mbind vma merge problem") introduced vma merging to mbind(), but it should have also changed the convention of passing start vma from queue_pages_range() (formerly check_range()) to new_vma_page(): vma merging may have already freed that structure, resulting in BUG at mm/mempolicy.c:1738 and probably worse crashes. Fixes: 9d8cebd4bcd7 ("mm: fix mbind vma merge problem") Reported-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Tested-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Christoph Lameter <cl@linux.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Minchan Kim <minchan.kim@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09sym53c8xx_2: Set DID_REQUEUE return code when aborting squeueMikulas Patocka
commit fd1232b214af43a973443aec6a2808f16ee5bf70 upstream. This patch fixes I/O errors with the sym53c8xx_2 driver when the disk returns QUEUE FULL status. When the controller encounters an error (including QUEUE FULL or BUSY status), it aborts all not yet submitted requests in the function sym_dequeue_from_squeue. This function aborts them with DID_SOFT_ERROR. If the disk has full tag queue, the request that caused the overflow is aborted with QUEUE FULL status (and the scsi midlayer properly retries it until it is accepted by the disk), but the sym53c8xx_2 driver aborts the following requests with DID_SOFT_ERROR --- for them, the midlayer does just a few retries and then signals the error up to sd. The result is that disk returning QUEUE FULL causes request failures. The error was reproduced on 53c895 with COMPAQ BD03685A24 disk (rebranded ST336607LC) with command queue 48 or 64 tags. The disk has 64 tags, but under some access patterns it return QUEUE FULL when there are less than 64 pending tags. The SCSI specification allows returning QUEUE FULL anytime and it is up to the host to retry. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09slab: fix oops when reading /proc/slab_allocatorsJoonsoo Kim
commit 03787301420376ae41fbaf4267f4a6253d152ac5 upstream. Commit b1cb0982bdd6 ("change the management method of free objects of the slab") introduced a bug on slab leak detector ('/proc/slab_allocators'). This detector works like as following decription. 1. traverse all objects on all the slabs. 2. determine whether it is active or not. 3. if active, print who allocate this object. but that commit changed the way how to manage free objects, so the logic determining whether it is active or not is also changed. In before, we regard object in cpu caches as inactive one, but, with this commit, we mistakenly regard object in cpu caches as active one. This intoduces kernel oops if DEBUG_PAGEALLOC is enabled. If DEBUG_PAGEALLOC is enabled, kernel_map_pages() is used to detect who corrupt free memory in the slab. It unmaps page table mapping if object is free and map it if object is active. When slab leak detector check object in cpu caches, it mistakenly think this object active so try to access object memory to retrieve caller of allocation. At this point, page table mapping to this object doesn't exist, so oops occurs. Following is oops message reported from Dave. It blew up when something tried to read /proc/slab_allocators (Just cat it, and you should see the oops below) Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC Modules linked in: [snip...] CPU: 1 PID: 9386 Comm: trinity-c33 Not tainted 3.14.0-rc5+ #131 task: ffff8801aa46e890 ti: ffff880076924000 task.ti: ffff880076924000 RIP: 0010:[<ffffffffaa1a8f4a>] [<ffffffffaa1a8f4a>] handle_slab+0x8a/0x180 RSP: 0018:ffff880076925de0 EFLAGS: 00010002 RAX: 0000000000001000 RBX: 0000000000000000 RCX: 000000005ce85ce7 RDX: ffffea00079be100 RSI: 0000000000001000 RDI: ffff880107458000 RBP: ffff880076925e18 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 000000000000000f R12: ffff8801e6f84000 R13: ffffea00079be100 R14: ffff880107458000 R15: ffff88022bb8d2c0 FS: 00007fb769e45740(0000) GS:ffff88024d040000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffff8801e6f84ff8 CR3: 00000000a22db000 CR4: 00000000001407e0 DR0: 0000000002695000 DR1: 0000000002695000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000070602 Call Trace: leaks_show+0xce/0x240 seq_read+0x28e/0x490 proc_reg_read+0x3d/0x80 vfs_read+0x9b/0x160 SyS_read+0x58/0xb0 tracesys+0xd4/0xd9 Code: f5 00 00 00 0f 1f 44 00 00 48 63 c8 44 3b 0c 8a 0f 84 e3 00 00 00 83 c0 01 44 39 c0 72 eb 41 f6 47 1a 01 0f 84 e9 00 00 00 89 f0 <4d> 8b 4c 04 f8 4d 85 c9 0f 84 88 00 00 00 49 8b 7e 08 4d 8d 46 RIP handle_slab+0x8a/0x180 To fix the problem, I introduce an object status buffer on each slab. With this, we can track object status precisely, so slab leak detector would not access active object and no kernel oops would occur. Memory overhead caused by this fix is only imposed to CONFIG_DEBUG_SLAB_LEAK which is mainly used for debugging, so memory overhead isn't big problem. Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-by: Dave Jones <davej@redhat.com> Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by: Vladimir Davydov <vdavydov@parallels.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09mm/numa: Remove BUG_ON() in __handle_mm_fault()Rik van Riel
commit 107437febd495a50e2cd09c81bbaa84d30e57b07 upstream. Changing PTEs and PMDs to pte_numa & pmd_numa is done with the mmap_sem held for reading, which means a pmd can be instantiated and turned into a numa one while __handle_mm_fault() is examining the value of old_pmd. If that happens, __handle_mm_fault() should just return and let the page fault retry, instead of throwing an oops. This is handled by the test for pmd_trans_huge(*pmd) below. Signed-off-by: Rik van Riel <riel@redhat.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reported-by: Sunil Pandey <sunil.k.pandey@intel.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: linux-mm@kvack.org Cc: lwoodman@redhat.com Cc: dave.hansen@intel.com Link: http://lkml.kernel.org/r/20140429153615.2d72098e@annuminas.surriel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Patrick McLean <chutzpah@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09drivers/video/fbdev/fb-puv3.c: Add header files for function unifb_mmapZhichuang SUN
commit fbc6c4a13bbfb420eedfdb26a0a859f9c07e8a7b upstream. Function unifb_mmap calls functions which are defined in linux/mm.h and asm/pgtable.h The related error (for unicore32 with unicore32_defconfig): CC drivers/video/fbdev/fb-puv3.o drivers/video/fbdev/fb-puv3.c: In function 'unifb_mmap': drivers/video/fbdev/fb-puv3.c:646: error: implicit declaration of function 'vm_iomap_memory' drivers/video/fbdev/fb-puv3.c:646: error: implicit declaration of function 'pgprot_noncached' Signed-off-by: Zhichuang Sun <sunzc522@gmail.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Joe Perches <joe@perches.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-fbdev@vger.kernel.org Acked-by: Xuetao Guan <gxt@mprc.pku.edu.cn> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09arch/unicore32/mm/alignment.c: include "asm/pgtable.h" to avoid compiling errorChen Gang
commit 1ff38c56cbd095c4c0dfa581a859ba3557830f78 upstream. Need include "asm/pgtable.h" to include "asm-generic/pgtable-nopmd.h", so can let 'pmd_t' defined. The related error with allmodconfig: CC arch/unicore32/mm/alignment.o In file included from arch/unicore32/mm/alignment.c:24: arch/unicore32/include/asm/tlbflush.h:135: error: expected .). before .*. token arch/unicore32/include/asm/tlbflush.h:154: error: expected .). before .*. token In file included from arch/unicore32/mm/alignment.c:27: arch/unicore32/mm/mm.h:15: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token arch/unicore32/mm/mm.h:20: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token arch/unicore32/mm/mm.h:25: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token make[1]: *** [arch/unicore32/mm/alignment.o] Error 1 make: *** [arch/unicore32/mm] Error 2 Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com> Acked-by: Xuetao Guan <gxt@mprc.pku.edu.cn> Signed-off-by: Xuetao Guan <gxt@mprc.pku.edu.cn> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09ALSA: usb-audio: Prevent printk ratelimiting from spamming kernel log while ↵Sander Eikelenboom
DEBUG not defined commit b7a7723513dc89f83d6df13206df55d4dc26e825 upstream. This (widely used) construction: if(printk_ratelimit()) dev_dbg() Causes the ratelimiting to spam the kernel log with the "callbacks suppressed" message below, even while the dev_dbg it is supposed to rate limit wouldn't print anything because DEBUG is not defined for this device. [ 533.803964] retire_playback_urb: 852 callbacks suppressed [ 538.807930] retire_playback_urb: 852 callbacks suppressed [ 543.811897] retire_playback_urb: 852 callbacks suppressed [ 548.815745] retire_playback_urb: 852 callbacks suppressed [ 553.819826] retire_playback_urb: 852 callbacks suppressed So use dev_dbg_ratelimited() instead of this construction. Signed-off-by: Sander Eikelenboom <linux@eikelenboom.it> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09ALSA: usb-audio: Suppress repetitive debug messages from retire_playback_urb()Tim Gardner
commit a5065eb6da55b226661456e6a7435f605df98111 upstream. BugLink: http://bugs.launchpad.net/bugs/1305133 Malfunctioning or slow devices can cause a flood of dmesg SPAM. I've ignored checkpatch.pl complaints about the use of printk_ratelimit() in favour of prior art in sound/usb/pcm.c. WARNING: Prefer printk_ratelimited or pr_<level>_ratelimited to printk_ratelimit + if (printk_ratelimit() && Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.de> Cc: Eldad Zack <eldad@fogrefinery.com> Cc: Daniel Mack <zonque@gmail.com> Cc: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09audit: remove superfluous new- prefix in AUDIT_LOGIN messagesRichard Guy Briggs
commit aa589a13b5d00d3c643ee4114d8cbc3addb4e99f upstream. The new- prefix on ses and auid are un-necessary and break ausearch. Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Reported-by: Steve Grubb <sgrubb@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09aio: block io_destroy() until all context requests are completedAnatol Pomozov
commit e02ba72aabfade4c9cd6e3263e9b57bf890ad25c upstream. deletes aio context and all resources related to. It makes sense that no IO operations connected to the context should be running after the context is destroyed. As we removed io_context we have no chance to get requests status or call io_getevents(). man page for io_destroy says that this function may block until all context's requests are completed. Before kernel 3.11 io_destroy() blocked indeed, but since aio refactoring in 3.11 it is not true anymore. Here is a pseudo-code that shows a testcase for a race condition discovered in 3.11: initialize io_context io_submit(read to buffer) io_destroy() // context is destroyed so we can free the resources free(buffers); // if the buffer is allocated by some other user he'll be surprised // to learn that the buffer still filled by an outstanding operation // from the destroyed io_context The fix is straight-forward - add a completion struct and wait on it in io_destroy, complete() should be called when number of in-fligh requests reaches zero. If two or more io_destroy() called for the same context simultaneously then only the first one waits for IO completion, other calls behaviour is undefined. Tested: ran http://pastebin.com/LrPsQ4RL testcase for several hours and do not see the race condition anymore. Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09drm/i915: fix display power sw state reportingImre Deak
commit b8c000d9bf23e7c1155ef421f595d1cbc25262da upstream. Atm, we refcount both power domains and power wells and intel_display_power_enabled_sw() returns the power domain refcount. What the callers are really interested in though is the sw state of the underlying power wells. Due to this we will report incorrectly that a given power domain is off if its power wells were enabled via another power domain, for example POWER_DOMAIN_INIT which enables all power wells. As a fix return instead the state based on the refcount of all power wells included in the passed in power domain. References: https://bugs.freedesktop.org/show_bug.cgi?id=79505 References: https://bugs.freedesktop.org/show_bug.cgi?id=79038 Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09mmc: rtsx: add R1-no-CRC mmc command type handleMicky Ching
commit 5027251eced6e34315a52bd841279df957f627bb upstream. a27fbf2f067b0cd ("mmc: add ignorance case for CMD13 CRC error") produced a cmd.flags unhandled in realtek pci host driver. This will make MMC card fail to initialize, this patch is used to handle the new cmd.flags condition and MMC card can be used. Signed-off-by: Micky Ching <micky_ching@realsil.com.cn> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09brcmfmac: Fix brcmf_chip_ai_coredisable not applying reset bits to BCMA_IOCTLHans de Goede
commit ffa216bb5eecfce0f01b0b2a95d5c320dde90005 upstream. brcmfmac has been broken on my cubietruck with a BCM43362: brcmfmac: brcmf_chip_recognition: found AXI chip: BCM43362, rev=1 brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d since commit 53036261033: "brcmfmac: update core reset and disable routines". The problem is that since this commit brcmf_chip_ai_resetcore no longer sets BCMA_IOCTL itself before bringing the core out of reset, instead relying on brcmf_chip_ai_coredisable to do so. But brcmf_chip_ai_coredisable is a nop of the chip is already in reset. This patch modifies brcmf_chip_ai_coredisable to always set BCMA_IOCTL even if the core is already in reset. This fixes brcmfmac hanging in firmware loading on my board. Cc: stable@vger.kernel.org # v3.14 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> [arend@broadcom.com: rebase patch on linux-3.14.y branch] Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09netfilter: nf_nat: fix oops on netns removalFlorian Westphal
commit 945b2b2d259d1a4364a2799e80e8ff32f8c6ee6f upstream. Quoting Samu Kallio: Basically what's happening is, during netns cleanup, nf_nat_net_exit gets called before ipv4_net_exit. As I understand it, nf_nat_net_exit is supposed to kill any conntrack entries which have NAT context (through nf_ct_iterate_cleanup), but for some reason this doesn't happen (perhaps something else is still holding refs to those entries?). When ipv4_net_exit is called, conntrack entries (including those with NAT context) are cleaned up, but the nat_bysource hashtable is long gone - freed in nf_nat_net_exit. The bug happens when attempting to free a conntrack entry whose NAT hash 'prev' field points to a slot in the freed hash table (head for that bin). We ignore conntracks with null nat bindings. But this is wrong, as these are in bysource hash table as well. Restore nat-cleaning for the netns-is-being-removed case. bug: https://bugzilla.kernel.org/show_bug.cgi?id=65191 Fixes: c2d421e1718 ('netfilter: nf_nat: fix race when unloading protocol modules') Reported-by: Samu Kallio <samu.kallio@aberdeencloud.com> Debugged-by: Samu Kallio <samu.kallio@aberdeencloud.com> Signed-off-by: Florian Westphal <fw@strlen.de> Tested-by: Samu Kallio <samu.kallio@aberdeencloud.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09tty: Correct INPCK handlingPeter Hurley
commit 66528f90669691c85c73bea4f0c9f4a5857c4cab upstream. If INPCK is not set, input parity detection should be disabled. This means parity errors should not be received from the tty driver, and the data received should be treated normally. SUS v3, 11.2.2, General Terminal Interface - Input Modes, states: "If INPCK is set, input parity checking shall be enabled. If INPCK is not set, input parity checking shall be disabled, allowing output parity generation without input parity errors. Note that whether input parity checking is enabled or disabled is independent of whether parity detection is enabled or disabled (see Control Modes). If parity detection is enabled but input parity checking is disabled, the hardware to which the terminal is connected shall recognize the parity bit, but the terminal special file shall not check whether or not this bit is correctly set." Ignore parity errors reported by the tty driver when INPCK is not set, and handle the received data normally. Fixes: Bugzilla #71681, 'Improvement of n_tty_receive_parity_error from n_tty.c' Reported-by: Ivan <athlon_@mail.ru> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09serial: Fix IGNBRK handlingPeter Hurley
commit ef8b9ddcb45fa3b1e11acd72be2398001e807d14 upstream. If IGNBRK is set without either BRKINT or PARMRK set, some uart drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the line discipline, when it should send either nothing or the TTYBREAK flag set. This happens because the read_status_mask masks out the BI condition, which uart_insert_char() then interprets as a normal 0x00 byte. SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General Terminal Interface - Input Modes, states: "If IGNBRK is set, a break condition detected on input shall be ignored; that is, not put on the input queue and therefore not read by any process." Fix read_status_mask to include the BI bit if IGNBRK is set; the lsr status retains the BI bit if a BREAK is recv'd, which is subsequently ignored in uart_insert_char() when masked with the ignore_status_mask. Affected drivers: 8250 - all serial_txx9 mfd amba-pl010 amba-pl011 atmel_serial bfin_uart dz ip22zilog max310x mxs-auart netx-serial pnx8xxx_uart pxa sb1250-duart sccnxp serial_ks8695 sirfsoc_uart st-asc vr41xx_siu zs sunzilog fsl_lpuart sunsab ucc_uart bcm63xx_uart sunsu efm32-uart pmac_zilog mpsc msm_serial m32r_sio Unaffected drivers: omap-serial rp2 sa1100 imx icom Annotated for fixes: altera_uart mcf Drivers without break detection: 21285 xilinx-uartps altera_jtaguart apbuart arc-uart clps711x max3100 uartlite msm_serial_hs nwpserial lantiq vt8500_serial Unknown: samsung mpc52xx_uart bfin_sport_uart cpm_uart/core Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag' Reported-by: Ivan <athlon_@mail.ru> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09clk: qcom: Fix mmcc-8974's PLL configurationsStephen Boyd
commit 437ae6a1b8f2eedebfbf0f6572e19ca5c58a3f71 upstream. We forgot to add the status bit for the PLLs and we were using the wrong register and masks for configuration, leading to unexpected PLL configurations. Fix this. Fixes: d8b212014e69 (clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)) Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09clk: qcom: Fix clk_rcg2_is_enabled() checkStephen Boyd
commit aa014149ba002155a084ec1e9328e95b70167cbb upstream. If the bit is set the clock is off so we should be checking for a clear bit, not a set bit. Invert the logic. Fixes: bcd61c0f535a (clk: qcom: Add support for root clock generators (RCGs)) Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09mlx4_core: Fix incorrect FLAGS1 bitmap test in mlx4_QUERY_FUNC_CAPJack Morgenstein
commit bc82878baa10c2a6a4a6affaf52c152935112142 upstream. Commit eb17711bc1d6 ("net/mlx4_core: Introduce nic_info new flag in QUERY_FUNC_CAP") did: if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_OFFSET) { which should be: if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_FORCE_VLAN) { Fix that. Fixes: eb17711bc1d6 ("net/mlx4_core: Introduce nic_info new flag in QUERY_FUNC_CAP") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDERMichal Nazarewicz
commit dc78327c0ea7da5186d8cbc1647bd6088c5c9fa5 upstream. With a kernel configured with ARM64_64K_PAGES && !TRANSPARENT_HUGEPAGE, the following is triggered at early boot: SMP: Total of 8 processors activated. devtmpfs: initialized Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = fffffe0000050000 [00000008] *pgd=00000043fba00003, *pmd=00000043fba00003, *pte=00e0000078010407 Internal error: Oops: 96000006 [#1] SMP Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc864k+ #44 task: fffffe03bc040000 ti: fffffe03bc080000 task.ti: fffffe03bc080000 PC is at __list_add+0x10/0xd4 LR is at free_one_page+0x270/0x638 ... Call trace: __list_add+0x10/0xd4 free_one_page+0x26c/0x638 __free_pages_ok.part.52+0x84/0xbc __free_pages+0x74/0xbc init_cma_reserved_pageblock+0xe8/0x104 cma_init_reserved_areas+0x190/0x1e4 do_one_initcall+0xc4/0x154 kernel_init_freeable+0x204/0x2a8 kernel_init+0xc/0xd4 This happens because init_cma_reserved_pageblock() calls __free_one_page() with pageblock_order as page order but it is bigger than MAX_ORDER. This in turn causes accesses past zone->free_list[]. Fix the problem by changing init_cma_reserved_pageblock() such that it splits pageblock into individual MAX_ORDER pages if pageblock is bigger than a MAX_ORDER page. In cases where !CONFIG_HUGETLB_PAGE_SIZE_VARIABLE, which is all architectures expect for ia64, powerpc and tile at the moment, the “pageblock_order > MAX_ORDER” condition will be optimised out since both sides of the operator are constants. In cases where pageblock size is variable, the performance degradation should not be significant anyway since init_cma_reserved_pageblock() is called only at boot time at most MAX_CMA_AREAS times which by default is eight. Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Reported-by: Mark Salter <msalter@redhat.com> Tested-by: Mark Salter <msalter@redhat.com> Tested-by: Christopher Covington <cov@codeaurora.org> Cc: Mel Gorman <mgorman@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09irqchip: spear_shirq: Fix interrupt offsetThomas Gleixner
commit 4f4366033945419b0c52118c29d3057d7c558765 upstream. The ras3 block on spear320 claims to have 3 interrupts. In fact it has one and 6 reserved interrupts. Account the 6 reserved to this block so it has 7 interrupts total. That matches the datasheet and the device tree entries. Broken since commit 80515a5a(ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT). Testing is overrated.... Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20140619212712.872379208@linutronix.de Fixes: 80515a5a2e3c ('ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT') Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09md: flush writes before starting a recovery.NeilBrown
commit 133d4527eab8d199a62eee6bd433f0776842df2e upstream. When we write to a degraded array which has a bitmap, we make sure the relevant bit in the bitmap remains set when the write completes (so a 're-add' can quickly rebuilt a temporarily-missing device). If, immediately after such a write starts, we incorporate a spare, commence recovery, and skip over the region where the write is happening (because the 'needs recovery' flag isn't set yet), then that write will not get to the new device. Once the recovery finishes the new device will be trusted, but will have incorrect data, leading to possible corruption. We cannot set the 'needs recovery' flag when we start the write as we do not know easily if the write will be "degraded" or not. That depends on details of the particular raid level and particular write request. This patch fixes a corruption issue of long standing and so it suitable for any -stable kernel. It applied correctly to 3.0 at least and will minor editing to earlier kernels. Reported-by: Bill <billstuff2001@sbcglobal.net> Tested-by: Bill <billstuff2001@sbcglobal.net> Link: http://lkml.kernel.org/r/53A518BB.60709@sbcglobal.net Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09tracing: Remove ftrace_stop/start() from reading the trace fileSteven Rostedt (Red Hat)
commit 099ed151675cd1d2dbeae1dac697975f6a68716d upstream. Disabling reading and writing to the trace file should not be able to disable all function tracing callbacks. There's other users today (like kprobes and perf). Reading a trace file should not stop those from happening. Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09tools: ffs-test: fix header values endianessMichal Nazarewicz
commit f35f71244da6e51db4e1f2c7e318581f498ececf upstream. It appears that no one ever run ffs-test on a big-endian machine, since it used cpu-endianess for fs_count and hs_count fields which should be in little-endian format. Fix by wrapping the numbers in cpu_to_le32. Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09nfsd: fix rare symlink decoding bugJ. Bruce Fields
commit 76f47128f9b33af1e96819746550d789054c9664 upstream. An NFS operation that creates a new symlink includes the symlink data, which is xdr-encoded as a length followed by the data plus 0 to 3 bytes of zero-padding as required to reach a 4-byte boundary. The vfs, on the other hand, wants null-terminated data. The simple way to handle this would be by copying the data into a newly allocated buffer with space for the final null. The current nfsd_symlink code tries to be more clever by skipping that step in the (likely) case where the byte following the string is already 0. But that assumes that the byte following the string is ours to look at. In fact, it might be the first byte of a page that we can't read, or of some object that another task might modify. Worse, the NFSv4 code tries to fix the problem by actually writing to that byte. In the NFSv2/v3 cases this actually appears to be safe: - nfs3svc_decode_symlinkargs explicitly null-terminates the data (after first checking its length and copying it to a new page). - NFSv2 limits symlinks to 1k. The buffer holding the rpc request is always at least a page, and the link data (and previous fields) have maximum lengths that prevent the request from reaching the end of a page. In the NFSv4 case the CREATE op is potentially just one part of a long compound so can end up on the end of a page if you're unlucky. The minimal fix here is to copy and null-terminate in the NFSv4 case. The nfsd_symlink() interface here seems too fragile, though. It should really either do the copy itself every time or just require a null-terminated string. Reported-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09staging: iio/ad7291: fix error code in ad7291_probe()Dan Carpenter
commit b70e19c222a64018d308ebc80333575aff9f4e51 upstream. We should be returning a negative error code instead of success here. This would have been detected by GCC, except that the "ret" variable was initialized with a bogus value to disable GCC's uninitialized variable warnings. I've cleaned that up, as well. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09iio: of_iio_channel_get_by_name() returns non-null pointers for error legsAdam Thomson
commit a2c12493ed7e63a18cef33a71686d12ffcd6600e upstream. Currently in the inkern.c code for IIO framework, the function of_iio_channel_get_by_name() will return a non-NULL pointer when it cannot find a channel using of_iio_channel_get() and when it tries to search for 'io-channel-ranges' property and fails. This is incorrect behaviour as the function which calls this expects a NULL pointer for failure. This patch rectifies the issue. Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09kvm: fix wrong address when writing Hyper-V tsc pageXiaoming Gao
commit e1fa108d24697b78348fd4e5a531029a50d0d36d upstream. When kvm_write_guest writes the tsc_ref structure to the guest, or it will lead the low HV_X64_MSR_TSC_REFERENCE_ADDRESS_SHIFT bits of the TSC page address must be cleared, or the guest can see a non-zero sequence number. Otherwise Windows guests would not be able to get a correct clocksource (QueryPerformanceCounter will always return 0) which causes serious chaos. Signed-off-by: Xiaoming Gao <newtongao@tencnet.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09KVM: x86: preserve the high 32-bits of the PAT registerPaolo Bonzini
commit 7cb060a91c0efc5ff94f83c6df3ed705e143cdb9 upstream. KVM does not really do much with the PAT, so this went unnoticed for a long time. It is exposed however if you try to do rdmsr on the PAT register. Reported-by: Valentine Sinitsyn <valentine.sinitsyn@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09KVM: x86: Increase the number of fixed MTRR regs to 10Nadav Amit
commit 682367c494869008eb89ef733f196e99415ae862 upstream. Recent Intel CPUs have 10 variable range MTRRs. Since operating systems sometime make assumptions on CPUs while they ignore capability MSRs, it is better for KVM to be consistent with recent CPUs. Reporting more MTRRs than actually supported has no functional implications. Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09ext4: Fix hole punching for files with indirect blocksJan Kara
commit a93cd4cf86466caa49cfe64607bea7f0bde3f916 upstream. Hole punching code for files with indirect blocks wrongly computed number of blocks which need to be cleared when traversing the indirect block tree. That could result in punching more blocks than actually requested and thus effectively cause a data loss. For example: fallocate -n -p 10240000 4096 will punch the range 10240000 - 12632064 instead of the range 1024000 - 10244096. Fix the calculation. Fixes: 8bad6fc813a3a5300f51369c39d315679fd88c72 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09ext4: Fix buffer double free in ext4_alloc_branch()Jan Kara
commit c5c7b8ddfbf8cb3b2291e515a34ab1b8982f5a2d upstream. Error recovery in ext4_alloc_branch() calls ext4_forget() even for buffer corresponding to indirect block it did not allocate. This leads to brelse() being called twice for that buffer (once from ext4_forget() and once from cleanup in ext4_ind_map_blocks()) leading to buffer use count misaccounting. Eventually (but often much later because there are other users of the buffer) we will see messages like: VFS: brelse: Trying to free free buffer Another manifestation of this problem is an error: JBD2 unexpected failure: jbd2_journal_revoke: !buffer_revoked(bh); inconsistent data on disk The fix is easy - don't forget buffer we did not allocate. Also add an explanatory comment because the indexing at ext4_alloc_branch() is somewhat subtle. Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-04 09:08:47 +0000