| Age | Commit message (Collapse) | Author |
|---|
|
WARNING: /lib/modules/2.6.17-mm2/kernel/net/ieee80211/ieee80211.ko
needs unknown symbol wireless_spy_update
Someone removed the `#ifdef CONFIG_WIRELESS_EXT' from around the callsite
in net/ieee80211/ieee80211_rx.c and didn't update Kconfig appropriately.
The offending patchset seems to be 35c14b855f52c49e4f3d078b9532b056005ed321
which is tittled
[PATCH] ieee80211: remove unnecessary CONFIG_WIRELESS_EXT checking
After a quick look it seems that wireless_spy_update() lives in
net/core/wirless.c, and that file is only compiled if
CONFIG_WIRELESS_EXT is set. Perhaps this is Kconig work, but
in the mean time here is a reversal of the recent change.
Signed-Off-By: Horms <horms@verge.net.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
times out
The ieee80211softmac_call_events function, when called with event type
IEEE80211SOFTMAC_EVENT_ASSOCIATE_TIMEOUT should pass the network as the
third parameter. This patch does that.
Signed-off-by: Joseph Jezak <josejx@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch addresses the "No queue exists" messages commonly seen during
authentication and associating. These appear due to scheduling multiple
authentication attempts on the same network. To prevent this, I added a
flag to stop multiple authentication attempts by the association layer.
I also added a check to the wx handler to see if we're connecting to a
different network than the one already in progress. This scenario was
causing multiple requests on the same network because the network BSSID
was not being updated despite the fact that the ESSID changed.
Signed-off-by: Joseph Jezak <josejx@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
I recently patched softmac to enable shared key authentication. This small patch
will enable crazy or unfortunate bcm43xx users to use this new capability.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ieee80211softmac_assoc_req
In commit ba9b28d19a3251bb1dfe6a6f8cc89b96fb85f683, routine
ieee80211softmac_capabilities was added to ieee80211softmac_io.c. As
denoted by its name, it completes the capabilities IE that is
needed in the associate and reassociate requests sent to the
AP. For at least one AP, the Linksys WRT54G V5, the capabilities
field must set the 'short preamble' bit or the AP refuses to
associate. In the commit noted above, there is a call to the
new routine from ieee80211softmac_reassoc_req, but not from
ieee80211softmac_assoc_req. This patch fixes that oversight.
As noted in the subject, v2.6.17 is affected. My bcm43xx card had been
unable to associate since I was forced to buy a new AP. I finally was
able to get a packet dump and traced the problem to the capabilities
info. Although I had heard that a patch was "floating around", I had
not seen it before 2.6.17 was released. As this bug does not affect
security and I seem to have the only AP affected by it, there should
be no problem in leaving it for 2.6.18.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The current version of bcm43xx-softmac uses local routines to check
if a channel is valid. As noted in the comments, these routines do
not take any regulatory information into account. This patch converts
the code to use the equivalent routine in ieee80211, which is being
converted to know about regulatory information.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
this patch fixes coverity id #913. ieee80211_monitor_rx() passes the skb
to netif_rx() and we should not reference it any longer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ieee80211_tx_frame
We should preallocate IV+ICV space when encrypting the frame.
Currently no problem shows up just because dev_alloc_skb aligns the
data len to SMP_CACHE_BYTES which can be used for ICV.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Place the Init-vs-IRQ workaround before any card register
access, because we might not have the wireless core mapped
at all times in init. So this will result in a Machine Check
caused by a bus error.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use Softmac-suggested TX ratecode:
ieee80211softmac_suggest_txrate()
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds device IDs for Symbol LA-4123 and Global Sun Tech
GL24110P to the HostAP PLX driver.
This is not tested with real hardware, but there is no reason why it
shouldn't work.
Please test.
Signed-off-by: Faidon Liambotis <faidon@cube.gr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Suggested by Jiri Slaby.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
For messages prior to register_netdev(), prefer dev_printk() because
that prints out both our driver name and our [PCI | whatever] bus id.
Updates: 8139{cp,too}, b44, bnx2, cassini, {eepro,epic}100, fealnx,
hamachi, ne2k-pci, ns83820, pci-skeleton, r8169.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Replace io_size struct members with VELOCITY_IO_SIZE constant.
Also, constify chip_info_table[].
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
- const-ify pci_device_id table
- clean up pci_device_id table with PCI_DEVICE()
- don't store internal pointer in pci_device_id table,
use pci_device_id::driver_data as an integer index
- use dev_printk() for messages where eth%d prefix is unavailable
- formatting fixes
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
- fealnx: convert #define to enum
- fealnx, sundance: mark chip info table __devinitdata
- fealnx: use dev_printk() during probe
- fealnx: formatting cleanups
- starfire: remove obsolete comment
- sundance, via-rhine: add some whitespace where useful, in tables
- sundance: prefer "{ }" table terminator
- via-rhine: mark PCI probe table const
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Becker-derived drivers often have the 'io_size' member in their chip
info struct, indicating the minimum required size of the I/O resource
(usually a PCI BAR). For many situations, this number is either
constant or irrelevant (due to pci_iomap convenience behavior).
This change removes the io_size invariant member, and replaces it with a
compile-time constant.
Drivers updated: fealnx, gt96100eth, winbond-840, yellowfin
Additionally,
- gt96100eth: unused 'drv_flags' removed from gt96100eth
- winbond-840: unused struct match_info removed
- winbond-840: mark pci_id_tbl[] const, __devinitdata
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
When in-kernel net drivers branched from Donald Becker's vanilla driver
set, in the days before BitKeeper and git, a driver changelog was
maintained in the driver source code. These days, the kernel's
changelog is far superior and much more accurate, so the in-driver
changelogs are removed.
Another relic of the Becker/kernel split was version numbering, using
"foo-LKx.y.z" notation, resulting in weird version numbers like
"1.17b-LK1.1.9". These drivers are for older hardware, and see few
changes these days, so the version numbers were all bumped to something
more simple.
Finally, in xircom_tulip_cb specifically, an additional cleanup removes
the always-enabled CARDBUS cpp macro.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
- Remove in-source changelog, it's in the global kernel history.
- convert silly and useless version to useful one
- replace invariant pci_id_tbl[]::io_size uses with EPIC_TOTAL_SIZE
- remove now-unused io_size member from pci_id_tbl[]
- current kernel style prefers dev_printk() for the rare ethernet driver
messages that cannot print an 'eth%d' prefix.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
In the case when compiling via a symlink tree, we want to ensure that the
close-to-open GETATTR call is applied only to the final file, and not to
the symlink.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
* the client is ia64 or any platform that actually implements
flush_dcache_page(), and
* the server returns fsinfo.dtpref >= client's PAGE_SIZE, and
* the server does *not* return post-op attributes for the directory
in the READDIR reply.
Problem diagnosed by Greg Banks <gnb@melbourne.sgi.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The introduction of the FLUSH_INVALIDATE argument to nfs_sync_inode_wait()
does not clear the nr_unstable page state counter for pages that are being
released.
Also fix a longstanding similar bug when nfs_commit_list() fails.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Use FL_ACCESS flag to test and/or wait for local locks before we try
requesting a lock from the server
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Use the new behaviour of {flock,posix}_file_lock(F_UNLCK) to determine if
we held a lock, and only send the RPC request to the server if this was the
case.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Change posix_lock_file_conf(), and flock_lock_file() so that if called
with an F_UNLCK argument, and the FL_EXISTS flag they will indicate
whether or not any locks were actually freed by returning 0 or -ENOENT.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
|
|
Fix a typo in the toplevel makefile.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
asm-powerpc/cputime.h doesn't declare jiffies64_to_cputime64() or
cputime64_sub(), and due to CONFIG_VIRT_CPU_ACCOUNTING it's not picking
up the definition from asm-generic like x86-64 & friends do.
Cc: Dave Jones <davej@redhat.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With the new interrupt rework, an interrupt "host" map() callback can be
called after the interrupt is already active.
It's called again for an already mapped interrupt to allow changing the
trigger setup, and currently this is not guarded with a test of wether
the interrupt is requested or not.
I plan to change some of this logic to be a bit less lenient against
random reconfiguring of live interrupts but just not yet.
The ported MPIC driver has a bug where when that happens, it will mask
the interrupt. This changes it to preserve the previous masking of the
interrupt instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Patch from Andrew Victor
The AIC interrupt controller is the same on the Atmel AT91RM9200,
AT91SAM9261 and AT91SAM9260 processors.
This patch removes any RM9200-specific naming from the IRQ driver, and
moves the AT91RM9200's default IRQ priority table into at91rm9200.c.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Vitaly Wool
Convert pnx4008 chip support to use generic irq subsystem
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Andrew Victor
The AT91RM9200 errata work-around should be using the GPIO API and not
accessing the PIO registers directly.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
Move workqueue exports to where the functions are defined.
[CPUFREQ] Misc cleanups in ondemand.
[CPUFREQ] Make ondemand sampling per CPU and remove the mutex usage in sampling path.
[CPUFREQ] Add queue_delayed_work_on() interface for workqueues.
[CPUFREQ] Remove slowdown from ondemand sampling path.
|
|
No devfs_fs.h header any more..
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* git://git.infradead.org/hdrinstall-2.6:
Remove export of include/linux/isdn/tpam.h
Remove <linux/i2c-id.h> and <linux/i2c-algo-ite.h> from userspace export
Restrict headers exported to userspace for SPARC and SPARC64
Add empty Kbuild files for 'make headers_install' in remaining arches.
Add Kbuild file for Alpha 'make headers_install'
Add Kbuild file for SPARC 'make headers_install'
Add Kbuild file for IA64 'make headers_install'
Add Kbuild file for S390 'make headers_install'
Add Kbuild file for i386 'make headers_install'
Add Kbuild file for x86_64 'make headers_install'
Add Kbuild file for PowerPC 'make headers_install'
Add generic Kbuild files for 'make headers_install'
Basic implementation of 'make headers_check'
Basic implementation of 'make headers_install'
|
|
There is a code sequence where the locking is substream->self_group.lock
-> ins->scbs[index].lock
substream->self_group.lock is interrupt safe, and taken from irq context
as well (trace is snipped for brevity)
so what can happen is
cpu 0 cpu 1
user context user context
take ins->scbs[index].lock without disabling interrupts
get substream->self_group.lock (irqsafe)
try to get ins->scbs[index].lock (spins)
interrupt happens
try to get substream->self_group.lock (spins)
which is an obvious AB-BA deadlock
fix is to just take the lock with _irqsafe
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
mthca: initialize send and receive queue locks separately
lockdep identifies a lock by the call site of its initialization. By
initializing the send and receive queue locks in mthca_wq_init() we confuse
lockdep. It warns that that the ordered acquiry of both locks in
mthca_modify_qp() is recursive acquiry of one lock:
=============================================
[ INFO: possible recursive locking detected ]
---------------------------------------------
modprobe/1192 is trying to acquire lock:
(&wq->lock){....}, at: [<f892b4db>] mthca_modify_qp+0x60/0xa7b [ib_mthca]
but task is already holding lock:
(&wq->lock){....}, at: [<f892b4ce>] mthca_modify_qp+0x53/0xa7b [ib_mthca]
Initializing the locks separately in mthca_alloc_qp_common() stops the
warning and will let lockdep enforce proper ordering on paths that acquire
both locks.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I found a bug in memory hot-add code for ia64.
IA64's code has copies of pgdat's array on each node to reduce memory
access over crossing node. This array is used by NODE_DATA() macro. When
new node is hot-added, this pgdat's array should be updated and copied on
new node too.
However, I used for_each_online_node() in scatter_node_data() to copy
it. This meant its array is not copied on new node.
Because initialization of structures for new node was halfway,
so online_node_map couldn't be set at this time.
To copy arrays on new node, I changed it to check value of pgdat_list[]
which is source array of copies. I tested this patch with my Memory Hotadd
emulation on Tiger4. This patch is for 2.6.17-git20.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix changed name of proc_task() to get_proc_task().
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (44 commits)
ACPI: remove function tracing macros from drivers/acpi/*.c
ACPI: add support for Smart Battery
ACPI: handle battery notify event on broken BIOS
ACPI: handle AC notify event on broken BIOS
ACPI: asus_acpi: add S1N WLED control
ACPI: asus_acpi: correct M6N/M6R display nodes
ACPI: asus_acpi: add S1N WLED control
ACPI: asus_acpi: rework model detection
ACPI: asus_acpi: support L5D
ACPI: asus_acpi: handle internal Bluetooth / support W5A
ACPI: asus_acpi: support A4G
ACPI: asus_acpi: support W3400N
ACPI: asus_acpi: LED display support
ACPI: asus_acpi: support A3G
ACPI: asus_acpi: misc cleanups
ACPI: video: Remove unneeded acpi_handle from driver.
ACPI: thermal: Remove unneeded acpi_handle from driver.
ACPI: power: Remove unneeded acpi_handle from driver.
ACPI: pci_root: Remove unneeded acpi_handle from driver.
ACPI: pci_link: Remove unneeded acpi_handle from driver.
...
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Ensure 8250_pci quirks are not marked __devinit
[SERIAL] Convert fifosize to an unsigned int
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Fix lh7a40x_udc.c
[ARM] Fix warning in consistent.c
[ARM] Fix warnings in arch/arm/kernel/setup.c
[ARM] Fix ecard.c resource warnings.
[ARM] Fix ISA IRQ resources
[ARM] Fix bad asm instruction in proc-arm925.S
[ARM] More missing proc-macros.S includes
[ARM] 3708/2: fix SMP build after section ioremap changes
|
|
* git://git.infradead.org/mtd-2.6:
[JFFS2][XATTR] Fix memory leak in POSIX-ACL support
fs/jffs2/: make 2 functions static
[MTD] NAND: Fix broken sharpsl driver
[JFFS2][XATTR] Fix xd->refcnt race condition
MTD: kernel-doc fixes + additions
MTD: fix all kernel-doc warnings
[MTD] DOC: Fixup read functions and do a little cleanup
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
[Bluetooth] Add RFCOMM role switch support
[Bluetooth] Allow disabling of credit based flow control
[Bluetooth] Small cleanup of the L2CAP source code
[Bluetooth] Use real devices for host controllers
[Bluetooth] Add platform device for virtual and serial devices
[Bluetooth] Add automatic sniff mode support
[Bluetooth] Correct SCO buffer size on request
[Bluetooth] Add suspend/resume support to the HCI USB driver
[Bluetooth] Use raw mode for the Frontline sniffer device
[BRIDGE]: br_dump_ifinfo index fix
[ATM]: add+use poison defines
[NET]: add+use poison defines
[IOAT]: fix kernel-doc in source files
[IOAT]: fix header file kernel-doc
[TG3]: Add ipv6 TSO feature
[IPV6]: Fix ipv6 GSO payload length
[TIPC] Fixed sk_buff panic caused by tipc_link_bundle_buf (REVISED)
[NET]: Verify gso_type too in gso_segment
[IPVS]: Add sysctl documentation
[ROSE]: Try all routes when establishing a ROSE connections.
...
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (57 commits)
[SCSI] fix error handling in scsi_io_completion
[SCSI] qla1280: fix section mismatch warnings
[SCSI] mptsas: eliminate ghost devices
[SCSI] qla2xxx: make some more functions static
[SCSI] small whitespace cleanup for qlogic driver
[SCSI] mptbase: mpt_interrupt should return IRQ_NONE
[SCSI] mptsas: make two functions static
[SCSI] sg.c: Fix bad error handling in
[SCSI] 53c700: fix breakage caused by the autosense update
[SCSI] iscsi: add async notification of session events
[SCSI] iscsi: pass target nr to session creation
[SCSI] iscsi: break up session creation into two stages
[SCSI] iscsi: rm channel usage from iscsi
[SCSI] iscsi: fix session refcouting
[SCSI] iscsi: convert iscsi_tcp to new set/get param fns
[SCSI] iscsi: convert iser to new set/get param fns
[SCSI] iscsi: fixup set/get param functions
[SCSI] iscsi: add target discvery event to transport class
[SCSI] st: remove unused st_buffer.in_use
[SCSI] atp870u: reduce huge stack usage
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: introduce utsrelease.h
kbuild: explicit turn off gcc stack-protector
|
