| Age | Commit message (Collapse) | Author |
|---|
|
The irq handler schedules a NAPI poll request unconditionally as soon as
the status register is not clean. It has been there - and wrong - for
ages but a recent timing change made it apparently easier to trigger.
Adrian Bunk:
backported to 2.6.16
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The PM hooks are no-op if the r8169 interface is down (i.e. !IFF_UP).
However, as the chipset is enabled, the device will not work after a
suspend/resume cycle. The patch always issue the required PCI suspend
sequence and removes the module unload/reload workaround.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Initialize the timer with the rest of the private-struct.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The attached fixes an oops in the usbnet driver. The same patch is
in 2.6.21-rc1, but that one has many whitespace changes. This is much
smaller.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
|
|
|
|
When we receive an AppleTalk frame shorter than what its header says,
we still attempt to verify its checksum, and trip on the BUG_ON() at
the end of function atalk_sum_skb() because of the length mismatch.
This has security implications because this can be triggered by simply
sending a specially crafted ethernet frame to a target victim,
effectively crashing that host. Thus this qualifies, I think, as a
remote DoS. Here is the frame I used to trigger the crash, in npg
format:
<Appletalk Killer>
{
# Ethernet header -----
XX XX XX XX XX XX # Destination MAC
00 00 00 00 00 00 # Source MAC
00 1D # Length
# LLC header -----
AA AA 03
08 00 07 80 9B # Appletalk
# Appletalk header -----
00 1B # Packet length (invalid)
00 01 # Fake checksum
00 00 00 00 # Destination and source networks
00 00 00 00 # Destination and source nodes and ports
# Payload -----
0C 0D 0E 0F 10 11 12 13
14
}
The destination MAC address must be set to those of the victim.
The severity is mitigated by two requirements:
* The target host must have the appletalk kernel module loaded. I
suspect this isn't so frequent.
* AppleTalk frames are non-IP, thus I guess they can only travel on
local networks. I am no network expert though, maybe it is possible
to somehow encapsulate AppleTalk packets over IP.
The bug has been reported back in June 2004:
http://bugzilla.kernel.org/show_bug.cgi?id=2979
But it wasn't investigated, and was closed in July 2006 as both
reporters had vanished meanwhile.
This code was new in kernel 2.6.0-test5:
http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=7ab442d7e0a76402c12553ee256f756097cae2d2
And not modified since then, so we can assume that vanilla kernels
2.6.0-test5 and later, and distribution kernels based thereon, are
affected.
Note that I still do not know for sure what triggered the bug in the
real-world cases. The frame could have been corrupted by the kernel if
we have a bug hiding somewhere. But more likely, we are receiving the
faulty frame from the network.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Fix two typos found by SiI680A documentation check. They caused the taskfile
transfer overclocking:
- in PIO mode 1 as 0x2283 must be used for both data and taskfile transfers;
- in PIO mode 2 as data and taskfile timings are swapped when writing to the
MMIO regs.
Fix coding style and trailing whitespace in enclosing statements while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
hrtimer_forward() does not check for the possible overflow of
timer->expires. This can happen on 64 bit machines with large interval
values and results currently in an endless loop in the softirq because
the expiry value becomes negative and therefor the timer is expired all
the time.
Check for this condition and set the expiry value to the max. expiry
time in the future.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The maximum seconds value we can handle on 32bit is LONG_MAX.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Frank v. Waveren pointed out that on 64bit machines the timespec to
ktime_t conversion might overflow. This is also true for timeval to
time_t conversions. This breaks a "sleep inf" on 64bit machines.
While a timespec/timeval with tx.sec = MAX_LONG is valid by specification
the internal representation of ktime_t is based on nanoseconds. The
conversion of seconds to nanoseconds overflows for seconds values >=
(MAX_LONG / NSEC_PER_SEC).
Check the seconds argument to the conversion and limit it to the maximum
time which can be represented by ktime_t.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This together with the phys_to_virt fix in lib/swiotlb.c::swiotlb_sync_sg
fixes video1394 DMA on machines with DMA bounce buffers, especially Intel
x86-64 machines with > 3GB RAM.
Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch fixes the case when we reparent to a different thread in the
same thread group. This modifies the code so that we do not send
signals and do not change the signal to send to SIGCHLD unless we have
change the thread group of our parents. It also suppresses sending
pdeath_sig in this cas as well since the result of geppid doesn't
change.
Thanks to Oleg for spotting my bug of only fixing this for non-ptraced
tasks.
This fixes the issues identified by Albert Cahalan in thread
http://lkml.org/lkml/2006/12/21/22
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Doug Leith observed a discrepancy between the version of CUBIC described
in the papers and the version in 2.6.18. A math error related to scaling
causes Cubic to grow too slowly.
Patch is from "Sangtae Ha" <sha2@ncsu.edu>. I validated that
it does fix the problems.
See the following to show behavior over 500ms 100 Mbit link.
Sender (2.6.19-rc3) --- Bridge (2.6.18-rt7) ------- Receiver (2.6.19-rc3)
1G [netem] 100M
http://developer.osdl.org/shemminger/tcp/2.6.19-rc3/cubic-orig.png
http://developer.osdl.org/shemminger/tcp/2.6.19-rc3/cubic-fix.png
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Noticed by Doug Nazar (via David Miller).
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
A ZIP or similar with unformatted media will cause crashes when attempts
are made to read/write it in some cases. This is because bs_factor is
zero and we divide by it causing an oops.
As the size of a non-accessible/non-existant media is really a bit of a
zen question it doesn't matter if non-existant media is 512 bytes per
sector or zero. Setting it to 1 causes us to generate 512 bytes/sector
accesses and error properly.
Based on a fix found lurking in an ancient bugzilla entry since about 2004 (ugghhh)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The determination of whether the DAC has inverted cursor logic is
broken, import the version checks the X.org driver uses to fix this.
Next, when we change the timing generator, borrow code from X.org that
does 10 NOP reads of the timing generator register afterwards to make
sure the video-enable transition occurs cleanly.
Finally, use macros for the DAC registers and fields in order to
provide documentation for the next person who reads this code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
|
|
|
|
Added the missing device assignment before creating sysfs tree.
This caused the insufficient device permissions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Fix the check of right channel in mixer volume put callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
snd_card_file_remove() may free hw->card so we can't dereference
hw->card->module after that.
Coverity ID 1420.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Fixed a typo in 'PC Speaker Playback Switch' control name.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
this is about coverity id #100.
It seems the if statement is negated, since the else branch calls
remove_info() with sflist->currsf as a parameter where it gets
dereferenced.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Fix the type of PCI revision to char from int and avoid invalid
assignment with pointer cast.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Fix the max number of codecs detected by HD-intel (and compatible)
controllers.
ATI controllers may have up to 4 codecs while ICH up to 3.
Now max codecs is defined according to the driver type, either 3 or 4.
Currently 4 is set only to ATI chips. Other might need the same
change, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Some modem codec seem to fail in the initialization, and this
stopped loading of the whole module although the audio is OK.
Since it's usually a non-fatal issue, the driver tries to proceed
to initialize now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The C-Media CM6501 chip's descriptors say that altsetting 5 supports
48 kHz, but it actually plays at 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Tetsuo Handa <handat@pm.nttdata.co.jp> told me that connect(2) with TCPv6
socket almost always took a few minutes to return when we did not have any
ports available in the range of net.ipv4.ip_local_port_range.
The reason was that we used incorrect seed for calculating index of
hash when we check established sockets in __inet6_check_established().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Guennadi Liakhovetski <gl@dsa-ac.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Ingress queueing uses a seperate lock for serializing enqueue operations,
but fails to properly protect itself against concurrent changes to the
qdisc tree. Use queue_lock for now since the real fix it quite intrusive.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
cls_basic doesn't allocate tp->root before it is linked into the
active classifier list, resulting in a NULL pointer dereference
when packets hit the classifier before its ->change function is
called.
Reported by Chris Madden <chris@reflexsecurity.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This adds an unusual_devs entry for the Motorola RAZR 3vi.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch adds an usual_devs entry for the Nokia 6288.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Device will not work as a mass storage device without US_FL_IGNORE_RESIDUE.
I bought this mp3 player that takes SD cards here
http://www.aiptek.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=AX4&Category_Code=MP3&Store_Code=AS
Signed-off-by: Dylan Taft <d13f00l@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch increases the range for 0x054c:0x002c devices to make
the following Sony USB floppy to work:
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=054c ProdID=002c Rev=20.00
S: Manufacturer=SONY
S: Product=USB Floppy
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=04 Prot=00 Driver=usb-storage
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=127ms
Signed-off-by: Marcelo Ricardo Leitner <mrl@mandriva.com>
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
There are multiple problems related to qlen adjustment that can lead
to an upper qdisc getting out of sync with the real number of packets
queued, leading to endless dequeueing attempts by the upper layer code.
All qdiscs must maintain an accurate q.qlen counter. There are basically
two groups of operations affecting the qlen: operations that propagate
down the tree (enqueue, dequeue, requeue, drop, reset) beginning at the
root qdisc and operations only affecting a subtree or single qdisc
(change, graft, delete class). Since qlen changes during operations from
the second group don't propagate to ancestor qdiscs, their qlen values
become desynchronized.
This patch adds a function to propagate qlen changes up the qdisc tree,
optionally calling a callback function to perform qdisc-internal
maintenance when the child qdisc is deactivated, and converts all
qdiscs to use this where necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
madvise(MADV_REMOVE) can go into an infinite loop or cause an oops if the
call covers a region from the start of a vma, and extending past that vma.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
A serial card might have been removed when the system is resumed.
This results in a suspended port being shut down, which results in
the ports shutdown method being called twice in a row. This causes
BUGs. Avoid this by tracking the suspended state separately from
the initialised state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Fix NULL pointer dereference on hot ejection of a FireWire card while
dv1394 was loaded. http://bugzilla.kernel.org/show_bug.cgi?id=7121
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
I have seen mdadm oops after successfully unloading md module.
This patch privents from unloading md module while
mdadm is polling /proc/mdstat.
Signed-off-by: Akinbou Mita <akinobu.mita@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
When iterating through an array, one must be careful to test one's index
variable rather than another similarly-named variable.
The loop will read off the end of conf->disks[] in the following
(pathological) case:
% dd bs=1 seek=840716287 if=/dev/zero of=d1 count=1
% for i in 2 3 4; do dd if=/dev/zero of=d$i bs=1k count=$(($i+150)); done
% ./vmlinux ubd0=root ubd1=d1 ubd2=d2 ubd3=d3 ubd4=d4
# mdadm -C /dev/md0 --level=linear --raid-devices=4 /dev/ubd[1234]
adding some printks, I saw this:
[42949374.960000] hash_spacing = 821120
[42949374.960000] cnt = 4
[42949374.960000] min_spacing = 801
[42949374.960000] j=0 size=820928 sz=820928
[42949374.960000] i=0 sz=820928 hash_spacing=820928
[42949374.960000] j=1 size=64 sz=64
[42949374.960000] j=2 size=64 sz=128
[42949374.960000] j=3 size=64 sz=192
[42949374.960000] j=4 size=1515870810 sz=1515871002
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
md raidX make_request functions strip off the BIO_RW_SYNC flag, thus
introducing additional latency.
Fixing this in raid1 and raid10 seems to be straightforward enough.
For our particular usage case in DRBD, passing this flag improved some
initialization time from ~5 minutes to ~5 seconds.
Signed-off-by: Lars Ellenberg <lars@linbit.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
If save_raid_disk is >= 0, then the device could be a device that is
already in sync that is being re-added. So we need to default this
value to -1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
If a drive is added with HOT_ADD_DISK rather than ADD_NEW_DISK,
saved_raid_disk isn't initialised properly, and the drive can be
included in the array without a resync.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch (as846) adds the IGNORE_RESIDUE flag to the unusual_devs
entry for Sony-Ericsson's P990i phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch (as749) extends the unusual_devs entry for the Sony DSC-T1 and
T5 to cover the H5 as well.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
