aboutsummaryrefslogtreecommitdiff
path: root/sound/soc/codecs/wm8978.c
diff options
context:
space:
mode:
Diffstat (limited to 'sound/soc/codecs/wm8978.c')
-rw-r--r--sound/soc/codecs/wm8978.c115
1 files changed, 78 insertions, 37 deletions
diff --git a/sound/soc/codecs/wm8978.c b/sound/soc/codecs/wm8978.c
index ec2624b4c37..28bb59ea6ea 100644
--- a/sound/soc/codecs/wm8978.c
+++ b/sound/soc/codecs/wm8978.c
@@ -58,6 +58,7 @@ struct wm8978_priv {
unsigned int f_mclk;
unsigned int f_256fs;
unsigned int f_opclk;
+ int mclk_idx;
enum wm8978_sysclk_src sysclk;
u16 reg_cache[WM8978_CACHEREGNUM];
};
@@ -402,6 +403,35 @@ static void pll_factors(struct wm8978_pll_div *pll_div, unsigned int target,
pll_div->k = k;
}
+
+/* MCLK dividers */
+static const int mclk_numerator[] = {1, 3, 2, 3, 4, 6, 8, 12};
+static const int mclk_denominator[] = {1, 2, 1, 1, 1, 1, 1, 1};
+
+/*
+ * find index >= idx, such that, for a given f_out,
+ * 3 * f_mclk / 4 <= f_PLLOUT < 13 * f_mclk / 4
+ * f_out can be f_256fs or f_opclk, currently only used for f_256fs. Can be
+ * generalised for f_opclk with suitable coefficient arrays, but currently
+ * the OPCLK divisor is calculated directly, not iteratively.
+ */
+static int wm8978_enum_mclk(unsigned int f_out, unsigned int f_mclk,
+ unsigned int *f_pllout)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(mclk_numerator); i++) {
+ unsigned int f_pllout_x4 = 4 * f_out * mclk_numerator[i] /
+ mclk_denominator[i];
+ if (3 * f_mclk <= f_pllout_x4 && f_pllout_x4 < 13 * f_mclk) {
+ *f_pllout = f_pllout_x4 / 4;
+ return i;
+ }
+ }
+
+ return -EINVAL;
+}
+
/*
* Calculate internal frequencies and dividers, according to Figure 40
* "PLL and Clock Select Circuit" in WM8978 datasheet Rev. 2.6
@@ -412,12 +442,16 @@ static int wm8978_configure_pll(struct snd_soc_codec *codec)
struct wm8978_pll_div pll_div;
unsigned int f_opclk = wm8978->f_opclk, f_mclk = wm8978->f_mclk,
f_256fs = wm8978->f_256fs;
- unsigned int f2, opclk_div;
+ unsigned int f2;
if (!f_mclk)
return -EINVAL;
if (f_opclk) {
+ unsigned int opclk_div;
+ /* Cannot set up MCLK divider now, do later */
+ wm8978->mclk_idx = -1;
+
/*
* The user needs OPCLK. Choose OPCLKDIV to put
* 6 <= R = f2 / f1 < 13, 1 <= OPCLKDIV <= 4.
@@ -444,7 +478,7 @@ static int wm8978_configure_pll(struct snd_soc_codec *codec)
wm8978->f_pllout = f_opclk * opclk_div;
} else if (f_256fs) {
/*
- * Not using OPCLK, choose R:
+ * Not using OPCLK, but PLL is used for the codec, choose R:
* 6 <= R = f2 / f1 < 13, to put 1 <= MCLKDIV <= 12.
* f_256fs = f_mclk * prescale * R / 4 / MCLKDIV, where
* prescale = 1, or prescale = 2. Prescale is calculated inside
@@ -453,18 +487,11 @@ static int wm8978_configure_pll(struct snd_soc_codec *codec)
* f_mclk * 3 / 48 <= f_256fs < f_mclk * 13 / 4. This means MCLK
* must be 3.781MHz <= f_MCLK <= 32.768MHz
*/
- if (48 * f_256fs < 3 * f_mclk || 4 * f_256fs >= 13 * f_mclk)
- return -EINVAL;
+ int idx = wm8978_enum_mclk(f_256fs, f_mclk, &wm8978->f_pllout);
+ if (idx < 0)
+ return idx;
- /*
- * MCLKDIV will be selected in .hw_params(), just choose a
- * suitable f_PLLOUT
- */
- if (4 * f_256fs < 3 * f_mclk)
- /* Will have to use MCLKDIV */
- wm8978->f_pllout = wm8978->f_mclk * 3 / 4;
- else
- wm8978->f_pllout = f_256fs;
+ wm8978->mclk_idx = idx;
/* GPIO1 into default mode as input - before configuring PLL */
snd_soc_update_bits(codec, WM8978_GPIO_CONTROL, 7, 0);
@@ -515,6 +542,20 @@ static int wm8978_set_dai_clkdiv(struct snd_soc_dai *codec_dai,
wm8978->f_opclk = div;
if (wm8978->f_mclk)
+ /*
+ * We know the MCLK frequency, the user has requested
+ * OPCLK, configure the PLL based on that and start it
+ * and OPCLK immediately. We will configure PLL to match
+ * user-requested OPCLK frquency as good as possible.
+ * In fact, it is likely, that matching the sampling
+ * rate, when it becomes known, is more important, and
+ * we will not be reconfiguring PLL then, because we
+ * must not interrupt OPCLK. But it should be fine,
+ * because typically the user will request OPCLK to run
+ * at 256fs or 512fs, and for these cases we will also
+ * find an exact MCLK divider configuration - it will
+ * be equal to or double the OPCLK divisor.
+ */
ret = wm8978_configure_pll(codec);
break;
case WM8978_BCLKDIV:
@@ -640,10 +681,6 @@ static int wm8978_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt)
return 0;
}
-/* MCLK dividers */
-static const int mclk_numerator[] = {1, 3, 2, 3, 4, 6, 8, 12};
-static const int mclk_denominator[] = {1, 2, 1, 1, 1, 1, 1, 1};
-
/*
* Set PCM DAI bit size and sample rate.
*/
@@ -709,9 +746,11 @@ static int wm8978_hw_params(struct snd_pcm_substream *substream,
wm8978->f_256fs = params_rate(params) * 256;
if (wm8978->sysclk == WM8978_MCLK) {
+ wm8978->mclk_idx = -1;
f_sel = wm8978->f_mclk;
} else {
if (!wm8978->f_pllout) {
+ /* We only enter here, if OPCLK is not used */
int ret = wm8978_configure_pll(codec);
if (ret < 0)
return ret;
@@ -719,32 +758,34 @@ static int wm8978_hw_params(struct snd_pcm_substream *substream,
f_sel = wm8978->f_pllout;
}
- /*
- * In some cases it is possible to reconfigure PLL to a higher frequency
- * by raising OPCLKDIV, but normally OPCLK is configured to 256 * fs or
- * 512 * fs, so, we should be fine.
- */
- if (f_sel < wm8978->f_256fs || f_sel > 12 * wm8978->f_256fs)
- return -EINVAL;
+ if (wm8978->mclk_idx < 0) {
+ /* Either MCLK is used directly, or OPCLK is used */
+ if (f_sel < wm8978->f_256fs || f_sel > 12 * wm8978->f_256fs)
+ return -EINVAL;
- for (i = 0; i < ARRAY_SIZE(mclk_numerator); i++) {
- diff = abs(wm8978->f_256fs * 3 -
- f_sel * 3 * mclk_denominator[i] / mclk_numerator[i]);
+ for (i = 0; i < ARRAY_SIZE(mclk_numerator); i++) {
+ diff = abs(wm8978->f_256fs * 3 -
+ f_sel * 3 * mclk_denominator[i] / mclk_numerator[i]);
- if (diff < diff_best) {
- diff_best = diff;
- best = i;
- }
+ if (diff < diff_best) {
+ diff_best = diff;
+ best = i;
+ }
- if (!diff)
- break;
+ if (!diff)
+ break;
+ }
+ } else {
+ /* OPCLK not used, codec driven by PLL */
+ best = wm8978->mclk_idx;
+ diff = 0;
}
if (diff)
- dev_warn(codec->dev, "Imprecise clock: %u%s\n",
- f_sel * mclk_denominator[best] / mclk_numerator[best],
- wm8978->sysclk == WM8978_MCLK ?
- ", consider using PLL" : "");
+ dev_warn(codec->dev, "Imprecise sampling rate: %uHz%s\n",
+ f_sel * mclk_denominator[best] / mclk_numerator[best] / 256,
+ wm8978->sysclk == WM8978_MCLK ?
+ ", consider using PLL" : "");
dev_dbg(codec->dev, "%s: fmt %d, rate %u, MCLK divisor #%d\n", __func__,
params_format(params), params_rate(params), best);
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-15 15:11:46 +0000