diff options
Diffstat (limited to 'sound/pci/hda/patch_cirrus.c')
| -rw-r--r-- | sound/pci/hda/patch_cirrus.c | 50 |
1 files changed, 50 insertions, 0 deletions
diff --git a/sound/pci/hda/patch_cirrus.c b/sound/pci/hda/patch_cirrus.c index ee1aea7296e..6adfc562528 100644 --- a/sound/pci/hda/patch_cirrus.c +++ b/sound/pci/hda/patch_cirrus.c @@ -968,6 +968,53 @@ static struct hda_verb cs_coef_init_verbs[] = { {} /* terminator */ }; +/* Errata: CS4207 rev C0/C1/C2 Silicon + * + * http://www.cirrus.com/en/pubs/errata/ER880C3.pdf + * + * 6. At high temperature (TA > +85°C), the digital supply current (IVD) + * may be excessive (up to an additional 200 μA), which is most easily + * observed while the part is being held in reset (RESET# active low). + * + * Root Cause: At initial powerup of the device, the logic that drives + * the clock and write enable to the S/PDIF SRC RAMs is not properly + * initialized. + * Certain random patterns will cause a steady leakage current in those + * RAM cells. The issue will resolve once the SRCs are used (turned on). + * + * Workaround: The following verb sequence briefly turns on the S/PDIF SRC + * blocks, which will alleviate the issue. + */ + +static struct hda_verb cs_errata_init_verbs[] = { + {0x01, AC_VERB_SET_POWER_STATE, 0x00}, /* AFG: D0 */ + {0x11, AC_VERB_SET_PROC_STATE, 0x01}, /* VPW: processing on */ + + {0x11, AC_VERB_SET_COEF_INDEX, 0x0008}, + {0x11, AC_VERB_SET_PROC_COEF, 0x9999}, + {0x11, AC_VERB_SET_COEF_INDEX, 0x0017}, + {0x11, AC_VERB_SET_PROC_COEF, 0xa412}, + {0x11, AC_VERB_SET_COEF_INDEX, 0x0001}, + {0x11, AC_VERB_SET_PROC_COEF, 0x0009}, + + {0x07, AC_VERB_SET_POWER_STATE, 0x00}, /* S/PDIF Rx: D0 */ + {0x08, AC_VERB_SET_POWER_STATE, 0x00}, /* S/PDIF Tx: D0 */ + + {0x11, AC_VERB_SET_COEF_INDEX, 0x0017}, + {0x11, AC_VERB_SET_PROC_COEF, 0x2412}, + {0x11, AC_VERB_SET_COEF_INDEX, 0x0008}, + {0x11, AC_VERB_SET_PROC_COEF, 0x0000}, + {0x11, AC_VERB_SET_COEF_INDEX, 0x0001}, + {0x11, AC_VERB_SET_PROC_COEF, 0x0008}, + {0x11, AC_VERB_SET_PROC_STATE, 0x00}, + + {0x07, AC_VERB_SET_POWER_STATE, 0x03}, /* S/PDIF Rx: D3 */ + {0x08, AC_VERB_SET_POWER_STATE, 0x03}, /* S/PDIF Tx: D3 */ + /*{0x01, AC_VERB_SET_POWER_STATE, 0x03},*/ /* AFG: D3 This is already handled */ + + {} /* terminator */ +}; + /* SPDIF setup */ static void init_digital(struct hda_codec *codec) { @@ -987,6 +1034,9 @@ static int cs_init(struct hda_codec *codec) { struct cs_spec *spec = codec->spec; + /* init_verb sequence for C0/C1/C2 errata*/ + snd_hda_sequence_write(codec, cs_errata_init_verbs); + snd_hda_sequence_write(codec, cs_coef_init_verbs); if (spec->gpio_mask) { |