1 files changed, 421 insertions, 18 deletions

diff --git a/kernel/time/ntp.c b/kernel/time/ntp.c
index c63116863a8..5c00242fa92 100644
--- a/kernel/time/ntp.c
+++ b/kernel/time/ntp.c
@@ -14,6 +14,7 @@
 #include <linux/timex.h>
 #include <linux/time.h>
 #include <linux/mm.h>
+#include <linux/module.h>
 
 /*
  * NTP timekeeping variables:
@@ -74,6 +75,162 @@ static long			time_adjust;
 /* constant (boot-param configurable) NTP tick adjustment (upscaled)	*/
 static s64			ntp_tick_adj;
 
+#ifdef CONFIG_NTP_PPS
+
+/*
+ * The following variables are used when a pulse-per-second (PPS) signal
+ * is available. They establish the engineering parameters of the clock
+ * discipline loop when controlled by the PPS signal.
+ */
+#define PPS_VALID	10	/* PPS signal watchdog max (s) */
+#define PPS_POPCORN	4	/* popcorn spike threshold (shift) */
+#define PPS_INTMIN	2	/* min freq interval (s) (shift) */
+#define PPS_INTMAX	8	/* max freq interval (s) (shift) */
+#define PPS_INTCOUNT	4	/* number of consecutive good intervals to
+				   increase pps_shift or consecutive bad
+				   intervals to decrease it */
+#define PPS_MAXWANDER	100000	/* max PPS freq wander (ns/s) */
+
+static int pps_valid;		/* signal watchdog counter */
+static long pps_tf[3];		/* phase median filter */
+static long pps_jitter;		/* current jitter (ns) */
+static struct timespec pps_fbase; /* beginning of the last freq interval */
+static int pps_shift;		/* current interval duration (s) (shift) */
+static int pps_intcnt;		/* interval counter */
+static s64 pps_freq;		/* frequency offset (scaled ns/s) */
+static long pps_stabil;		/* current stability (scaled ns/s) */
+
+/*
+ * PPS signal quality monitors
+ */
+static long pps_calcnt;		/* calibration intervals */
+static long pps_jitcnt;		/* jitter limit exceeded */
+static long pps_stbcnt;		/* stability limit exceeded */
+static long pps_errcnt;		/* calibration errors */
+
+
+/* PPS kernel consumer compensates the whole phase error immediately.
+ * Otherwise, reduce the offset by a fixed factor times the time constant.
+ */
+static inline s64 ntp_offset_chunk(s64 offset)
+{
+	if (time_status & STA_PPSTIME && time_status & STA_PPSSIGNAL)
+		return offset;
+	else
+		return shift_right(offset, SHIFT_PLL + time_constant);
+}
+
+static inline void pps_reset_freq_interval(void)
+{
+	/* the PPS calibration interval may end
+	   surprisingly early */
+	pps_shift = PPS_INTMIN;
+	pps_intcnt = 0;
+}
+
+/**
+ * pps_clear - Clears the PPS state variables
+ *
+ * Must be called while holding a write on the xtime_lock
+ */
+static inline void pps_clear(void)
+{
+	pps_reset_freq_interval();
+	pps_tf[0] = 0;
+	pps_tf[1] = 0;
+	pps_tf[2] = 0;
+	pps_fbase.tv_sec = pps_fbase.tv_nsec = 0;
+	pps_freq = 0;
+}
+
+/* Decrease pps_valid to indicate that another second has passed since
+ * the last PPS signal. When it reaches 0, indicate that PPS signal is
+ * missing.
+ *
+ * Must be called while holding a write on the xtime_lock
+ */
+static inline void pps_dec_valid(void)
+{
+	if (pps_valid > 0)
+		pps_valid--;
+	else {
+		time_status &= ~(STA_PPSSIGNAL | STA_PPSJITTER |
+				 STA_PPSWANDER | STA_PPSERROR);
+		pps_clear();
+	}
+}
+
+static inline void pps_set_freq(s64 freq)
+{
+	pps_freq = freq;
+}
+
+static inline int is_error_status(int status)
+{
+	return (time_status & (STA_UNSYNC|STA_CLOCKERR))
+		/* PPS signal lost when either PPS time or
+		 * PPS frequency synchronization requested
+		 */
+		|| ((time_status & (STA_PPSFREQ|STA_PPSTIME))
+			&& !(time_status & STA_PPSSIGNAL))
+		/* PPS jitter exceeded when
+		 * PPS time synchronization requested */
+		|| ((time_status & (STA_PPSTIME|STA_PPSJITTER))
+			== (STA_PPSTIME|STA_PPSJITTER))
+		/* PPS wander exceeded or calibration error when
+		 * PPS frequency synchronization requested
+		 */
+		|| ((time_status & STA_PPSFREQ)
+			&& (time_status & (STA_PPSWANDER|STA_PPSERROR)));
+}
+
+static inline void pps_fill_timex(struct timex *txc)
+{
+	txc->ppsfreq	   = shift_right((pps_freq >> PPM_SCALE_INV_SHIFT) *
+					 PPM_SCALE_INV, NTP_SCALE_SHIFT);
+	txc->jitter	   = pps_jitter;
+	if (!(time_status & STA_NANO))
+		txc->jitter /= NSEC_PER_USEC;
+	txc->shift	   = pps_shift;
+	txc->stabil	   = pps_stabil;
+	txc->jitcnt	   = pps_jitcnt;
+	txc->calcnt	   = pps_calcnt;
+	txc->errcnt	   = pps_errcnt;
+	txc->stbcnt	   = pps_stbcnt;
+}
+
+#else /* !CONFIG_NTP_PPS */
+
+static inline s64 ntp_offset_chunk(s64 offset)
+{
+	return shift_right(offset, SHIFT_PLL + time_constant);
+}
+
+static inline void pps_reset_freq_interval(void) {}
+static inline void pps_clear(void) {}
+static inline void pps_dec_valid(void) {}
+static inline void pps_set_freq(s64 freq) {}
+
+static inline int is_error_status(int status)
+{
+	return status & (STA_UNSYNC|STA_CLOCKERR);
+}
+
+static inline void pps_fill_timex(struct timex *txc)
+{
+	/* PPS is not implemented, so these are zero */
+	txc->ppsfreq	   = 0;
+	txc->jitter	   = 0;
+	txc->shift	   = 0;
+	txc->stabil	   = 0;
+	txc->jitcnt	   = 0;
+	txc->calcnt	   = 0;
+	txc->errcnt	   = 0;
+	txc->stbcnt	   = 0;
+}
+
+#endif /* CONFIG_NTP_PPS */
+
 /*
  * NTP methods:
  */
@@ -149,10 +306,18 @@ static void ntp_update_offset(long offset)
 	time_reftime = get_seconds();
 
 	offset64    = offset;
-	freq_adj    = (offset64 * secs) <<
-			(NTP_SCALE_SHIFT - 2 * (SHIFT_PLL + 2 + time_constant));
+	freq_adj    = ntp_update_offset_fll(offset64, secs);
 
-	freq_adj    += ntp_update_offset_fll(offset64, secs);
+	/*
+	 * Clamp update interval to reduce PLL gain with low
+	 * sampling rate (e.g. intermittent network connection)
+	 * to avoid instability.
+	 */
+	if (unlikely(secs > 1 << (SHIFT_PLL + 1 + time_constant)))
+		secs = 1 << (SHIFT_PLL + 1 + time_constant);
+
+	freq_adj    += (offset64 * secs) <<
+			(NTP_SCALE_SHIFT - 2 * (SHIFT_PLL + 2 + time_constant));
 
 	freq_adj    = min(freq_adj + time_freq, MAXFREQ_SCALED);
 
@@ -177,6 +342,9 @@ void ntp_clear(void)
 
 	tick_length	= tick_length_base;
 	time_offset	= 0;
+
+	/* Clear PPS state variables */
+	pps_clear();
 }
 
 /*
@@ -242,16 +410,16 @@ void second_overflow(void)
 		time_status |= STA_UNSYNC;
 	}
 
-	/*
-	 * Compute the phase adjustment for the next second. The offset is
-	 * reduced by a fixed factor times the time constant.
-	 */
+	/* Compute the phase adjustment for the next second */
 	tick_length	 = tick_length_base;
 
-	delta		 = shift_right(time_offset, SHIFT_PLL + time_constant);
+	delta		 = ntp_offset_chunk(time_offset);
 	time_offset	-= delta;
 	tick_length	+= delta;
 
+	/* Check PPS signal */
+	pps_dec_valid();
+
 	if (!time_adjust)
 		return;
 
@@ -361,6 +529,8 @@ static inline void process_adj_status(struct timex *txc, struct timespec *ts)
 	if ((time_status & STA_PLL) && !(txc->status & STA_PLL)) {
 		time_state = TIME_OK;
 		time_status = STA_UNSYNC;
+		/* restart PPS frequency calibration */
+		pps_reset_freq_interval();
 	}
 
 	/*
@@ -410,6 +580,8 @@ static inline void process_adjtimex_modes(struct timex *txc, struct timespec *ts
 		time_freq = txc->freq * PPM_SCALE;
 		time_freq = min(time_freq, MAXFREQ_SCALED);
 		time_freq = max(time_freq, -MAXFREQ_SCALED);
+		/* update pps_freq */
+		pps_set_freq(time_freq);
 	}
 
 	if (txc->modes & ADJ_MAXERROR)
@@ -500,7 +672,8 @@ int do_adjtimex(struct timex *txc)
 	}
 
 	result = time_state;	/* mostly `TIME_OK' */
-	if (time_status & (STA_UNSYNC|STA_CLOCKERR))
+	/* check for errors */
+	if (is_error_status(time_status))
 		result = TIME_ERROR;
 
 	txc->freq	   = shift_right((time_freq >> PPM_SCALE_INV_SHIFT) *
@@ -514,15 +687,8 @@ int do_adjtimex(struct timex *txc)
 	txc->tick	   = tick_usec;
 	txc->tai	   = time_tai;
 
-	/* PPS is not implemented, so these are zero */
-	txc->ppsfreq	   = 0;
-	txc->jitter	   = 0;
-	txc->shift	   = 0;
-	txc->stabil	   = 0;
-	txc->jitcnt	   = 0;
-	txc->calcnt	   = 0;
-	txc->errcnt	   = 0;
-	txc->stbcnt	   = 0;
+	/* fill PPS status fields */
+	pps_fill_timex(txc);
 
 	write_sequnlock_irq(&xtime_lock);
 
@@ -536,6 +702,243 @@ int do_adjtimex(struct timex *txc)
 	return result;
 }
 
+#ifdef	CONFIG_NTP_PPS
+
+/* actually struct pps_normtime is good old struct timespec, but it is
+ * semantically different (and it is the reason why it was invented):
+ * pps_normtime.nsec has a range of ( -NSEC_PER_SEC / 2, NSEC_PER_SEC / 2 ]
+ * while timespec.tv_nsec has a range of [0, NSEC_PER_SEC) */
+struct pps_normtime {
+	__kernel_time_t	sec;	/* seconds */
+	long		nsec;	/* nanoseconds */
+};
+
+/* normalize the timestamp so that nsec is in the
+   ( -NSEC_PER_SEC / 2, NSEC_PER_SEC / 2 ] interval */
+static inline struct pps_normtime pps_normalize_ts(struct timespec ts)
+{
+	struct pps_normtime norm = {
+		.sec = ts.tv_sec,
+		.nsec = ts.tv_nsec
+	};
+
+	if (norm.nsec > (NSEC_PER_SEC >> 1)) {
+		norm.nsec -= NSEC_PER_SEC;
+		norm.sec++;
+	}
+
+	return norm;
+}
+
+/* get current phase correction and jitter */
+static inline long pps_phase_filter_get(long *jitter)
+{
+	*jitter = pps_tf[0] - pps_tf[1];
+	if (*jitter < 0)
+		*jitter = -*jitter;
+
+	/* TODO: test various filters */
+	return pps_tf[0];
+}
+
+/* add the sample to the phase filter */
+static inline void pps_phase_filter_add(long err)
+{
+	pps_tf[2] = pps_tf[1];
+	pps_tf[1] = pps_tf[0];
+	pps_tf[0] = err;
+}
+
+/* decrease frequency calibration interval length.
+ * It is halved after four consecutive unstable intervals.
+ */
+static inline void pps_dec_freq_interval(void)
+{
+	if (--pps_intcnt <= -PPS_INTCOUNT) {
+		pps_intcnt = -PPS_INTCOUNT;
+		if (pps_shift > PPS_INTMIN) {
+			pps_shift--;
+			pps_intcnt = 0;
+		}
+	}
+}
+
+/* increase frequency calibration interval length.
+ * It is doubled after four consecutive stable intervals.
+ */
+static inline void pps_inc_freq_interval(void)
+{
+	if (++pps_intcnt >= PPS_INTCOUNT) {
+		pps_intcnt = PPS_INTCOUNT;
+		if (pps_shift < PPS_INTMAX) {
+			pps_shift++;
+			pps_intcnt = 0;
+		}
+	}
+}
+
+/* update clock frequency based on MONOTONIC_RAW clock PPS signal
+ * timestamps
+ *
+ * At the end of the calibration interval the difference between the
+ * first and last MONOTONIC_RAW clock timestamps divided by the length
+ * of the interval becomes the frequency update. If the interval was
+ * too long, the data are discarded.
+ * Returns the difference between old and new frequency values.
+ */
+static long hardpps_update_freq(struct pps_normtime freq_norm)
+{
+	long delta, delta_mod;
+	s64 ftemp;
+
+	/* check if the frequency interval was too long */
+	if (freq_norm.sec > (2 << pps_shift)) {
+		time_status |= STA_PPSERROR;
+		pps_errcnt++;
+		pps_dec_freq_interval();
+		pr_err("hardpps: PPSERROR: interval too long - %ld s\n",
+				freq_norm.sec);
+		return 0;
+	}
+
+	/* here the raw frequency offset and wander (stability) is
+	 * calculated. If the wander is less than the wander threshold
+	 * the interval is increased; otherwise it is decreased.
+	 */
+	ftemp = div_s64(((s64)(-freq_norm.nsec)) << NTP_SCALE_SHIFT,
+			freq_norm.sec);
+	delta = shift_right(ftemp - pps_freq, NTP_SCALE_SHIFT);
+	pps_freq = ftemp;
+	if (delta > PPS_MAXWANDER || delta < -PPS_MAXWANDER) {
+		pr_warning("hardpps: PPSWANDER: change=%ld\n", delta);
+		time_status |= STA_PPSWANDER;
+		pps_stbcnt++;
+		pps_dec_freq_interval();
+	} else {	/* good sample */
+		pps_inc_freq_interval();
+	}
+
+	/* the stability metric is calculated as the average of recent
+	 * frequency changes, but is used only for performance
+	 * monitoring
+	 */
+	delta_mod = delta;
+	if (delta_mod < 0)
+		delta_mod = -delta_mod;
+	pps_stabil += (div_s64(((s64)delta_mod) <<
+				(NTP_SCALE_SHIFT - SHIFT_USEC),
+				NSEC_PER_USEC) - pps_stabil) >> PPS_INTMIN;
+
+	/* if enabled, the system clock frequency is updated */
+	if ((time_status & STA_PPSFREQ) != 0 &&
+	    (time_status & STA_FREQHOLD) == 0) {
+		time_freq = pps_freq;
+		ntp_update_frequency();
+	}
+
+	return delta;
+}
+
+/* correct REALTIME clock phase error against PPS signal */
+static void hardpps_update_phase(long error)
+{
+	long correction = -error;
+	long jitter;
+
+	/* add the sample to the median filter */
+	pps_phase_filter_add(correction);
+	correction = pps_phase_filter_get(&jitter);
+
+	/* Nominal jitter is due to PPS signal noise. If it exceeds the
+	 * threshold, the sample is discarded; otherwise, if so enabled,
+	 * the time offset is updated.
+	 */
+	if (jitter > (pps_jitter << PPS_POPCORN)) {
+		pr_warning("hardpps: PPSJITTER: jitter=%ld, limit=%ld\n",
+		       jitter, (pps_jitter << PPS_POPCORN));
+		time_status |= STA_PPSJITTER;
+		pps_jitcnt++;
+	} else if (time_status & STA_PPSTIME) {
+		/* correct the time using the phase offset */
+		time_offset = div_s64(((s64)correction) << NTP_SCALE_SHIFT,
+				NTP_INTERVAL_FREQ);
+		/* cancel running adjtime() */
+		time_adjust = 0;
+	}
+	/* update jitter */
+	pps_jitter += (jitter - pps_jitter) >> PPS_INTMIN;
+}
+
+/*
+ * hardpps() - discipline CPU clock oscillator to external PPS signal
+ *
+ * This routine is called at each PPS signal arrival in order to
+ * discipline the CPU clock oscillator to the PPS signal. It takes two
+ * parameters: REALTIME and MONOTONIC_RAW clock timestamps. The former
+ * is used to correct clock phase error and the latter is used to
+ * correct the frequency.
+ *
+ * This code is based on David Mills's reference nanokernel
+ * implementation. It was mostly rewritten but keeps the same idea.
+ */
+void hardpps(const struct timespec *phase_ts, const struct timespec *raw_ts)
+{
+	struct pps_normtime pts_norm, freq_norm;
+	unsigned long flags;
+
+	pts_norm = pps_normalize_ts(*phase_ts);
+
+	write_seqlock_irqsave(&xtime_lock, flags);
+
+	/* clear the error bits, they will be set again if needed */
+	time_status &= ~(STA_PPSJITTER | STA_PPSWANDER | STA_PPSERROR);
+
+	/* indicate signal presence */
+	time_status |= STA_PPSSIGNAL;
+	pps_valid = PPS_VALID;
+
+	/* when called for the first time,
+	 * just start the frequency interval */
+	if (unlikely(pps_fbase.tv_sec == 0)) {
+		pps_fbase = *raw_ts;
+		write_sequnlock_irqrestore(&xtime_lock, flags);
+		return;
+	}
+
+	/* ok, now we have a base for frequency calculation */
+	freq_norm = pps_normalize_ts(timespec_sub(*raw_ts, pps_fbase));
+
+	/* check that the signal is in the range
+	 * [1s - MAXFREQ us, 1s + MAXFREQ us], otherwise reject it */
+	if ((freq_norm.sec == 0) ||
+			(freq_norm.nsec > MAXFREQ * freq_norm.sec) ||
+			(freq_norm.nsec < -MAXFREQ * freq_norm.sec)) {
+		time_status |= STA_PPSJITTER;
+		/* restart the frequency calibration interval */
+		pps_fbase = *raw_ts;
+		write_sequnlock_irqrestore(&xtime_lock, flags);
+		pr_err("hardpps: PPSJITTER: bad pulse\n");
+		return;
+	}
+
+	/* signal is ok */
+
+	/* check if the current frequency interval is finished */
+	if (freq_norm.sec >= (1 << pps_shift)) {
+		pps_calcnt++;
+		/* restart the frequency calibration interval */
+		pps_fbase = *raw_ts;
+		hardpps_update_freq(freq_norm);
+	}
+
+	hardpps_update_phase(pts_norm.nsec);
+
+	write_sequnlock_irqrestore(&xtime_lock, flags);
+}
+EXPORT_SYMBOL(hardpps);
+
+#endif	/* CONFIG_NTP_PPS */
+
 static int __init ntp_tick_adj_setup(char *str)
 {
 	ntp_tick_adj = simple_strtol(str, NULL, 0);