aboutsummaryrefslogtreecommitdiff
path: root/include
diff options
context:
space:
mode:
Diffstat (limited to 'include')
-rw-r--r--include/linux/i2c/dm355evm_msp.h79
-rw-r--r--include/linux/i2c/twl4030.h81
-rw-r--r--include/linux/mfd/da903x.h44
-rw-r--r--include/linux/mfd/wm8350/comparator.h8
-rw-r--r--include/linux/mfd/wm8350/core.h52
-rw-r--r--include/linux/mfd/wm8350/pmic.h4
-rw-r--r--include/linux/mfd/wm8350/supply.h25
-rw-r--r--include/linux/power_supply.h1
8 files changed, 256 insertions, 38 deletions
diff --git a/include/linux/i2c/dm355evm_msp.h b/include/linux/i2c/dm355evm_msp.h
new file mode 100644
index 00000000000..372470350fa
--- /dev/null
+++ b/include/linux/i2c/dm355evm_msp.h
@@ -0,0 +1,79 @@
+/*
+ * dm355evm_msp.h - support MSP430 microcontroller on DM355EVM board
+ */
+#ifndef __LINUX_I2C_DM355EVM_MSP
+#define __LINUX_I2C_DM355EVM_MSP
+
+/*
+ * Written against Spectrum's writeup for the A4 firmware revision,
+ * and tweaked to match source and rev D2 schematics by removing CPLD
+ * and NOR flash hooks (which were last appropriate in rev B boards).
+ *
+ * Note that the firmware supports a flavor of write posting ... to be
+ * sure a write completes, issue another read or write.
+ */
+
+/* utilities to access "registers" emulated by msp430 firmware */
+extern int dm355evm_msp_write(u8 value, u8 reg);
+extern int dm355evm_msp_read(u8 reg);
+
+
+/* command/control registers */
+#define DM355EVM_MSP_COMMAND 0x00
+# define MSP_COMMAND_NULL 0
+# define MSP_COMMAND_RESET_COLD 1
+# define MSP_COMMAND_RESET_WARM 2
+# define MSP_COMMAND_RESET_WARM_I 3
+# define MSP_COMMAND_POWEROFF 4
+# define MSP_COMMAND_IR_REINIT 5
+#define DM355EVM_MSP_STATUS 0x01
+# define MSP_STATUS_BAD_OFFSET BIT(0)
+# define MSP_STATUS_BAD_COMMAND BIT(1)
+# define MSP_STATUS_POWER_ERROR BIT(2)
+# define MSP_STATUS_RXBUF_OVERRUN BIT(3)
+#define DM355EVM_MSP_RESET 0x02 /* 0 bits == in reset */
+# define MSP_RESET_DC5 BIT(0)
+# define MSP_RESET_TVP5154 BIT(2)
+# define MSP_RESET_IMAGER BIT(3)
+# define MSP_RESET_ETHERNET BIT(4)
+# define MSP_RESET_SYS BIT(5)
+# define MSP_RESET_AIC33 BIT(7)
+
+/* GPIO registers ... bit patterns mostly match the source MSP ports */
+#define DM355EVM_MSP_LED 0x03 /* active low (MSP P4) */
+#define DM355EVM_MSP_SWITCH1 0x04 /* (MSP P5, masked) */
+# define MSP_SWITCH1_SW6_1 BIT(0)
+# define MSP_SWITCH1_SW6_2 BIT(1)
+# define MSP_SWITCH1_SW6_3 BIT(2)
+# define MSP_SWITCH1_SW6_4 BIT(3)
+# define MSP_SWITCH1_J1 BIT(4) /* NTSC/PAL */
+# define MSP_SWITCH1_MSP_INT BIT(5) /* active low */
+#define DM355EVM_MSP_SWITCH2 0x05 /* (MSP P6, masked) */
+# define MSP_SWITCH2_SW10 BIT(3)
+# define MSP_SWITCH2_SW11 BIT(4)
+# define MSP_SWITCH2_SW12 BIT(5)
+# define MSP_SWITCH2_SW13 BIT(6)
+# define MSP_SWITCH2_SW14 BIT(7)
+#define DM355EVM_MSP_SDMMC 0x06 /* (MSP P2, masked) */
+# define MSP_SDMMC_0_WP BIT(1)
+# define MSP_SDMMC_0_CD BIT(2) /* active low */
+# define MSP_SDMMC_1_WP BIT(3)
+# define MSP_SDMMC_1_CD BIT(4) /* active low */
+#define DM355EVM_MSP_FIRMREV 0x07 /* not a GPIO (out of order) */
+#define DM355EVM_MSP_VIDEO_IN 0x08 /* (MSP P3, masked) */
+# define MSP_VIDEO_IMAGER BIT(7) /* low == tvp5146 */
+
+/* power supply registers are currently omitted */
+
+/* RTC registers */
+#define DM355EVM_MSP_RTC_0 0x12 /* LSB */
+#define DM355EVM_MSP_RTC_1 0x13
+#define DM355EVM_MSP_RTC_2 0x14
+#define DM355EVM_MSP_RTC_3 0x15 /* MSB */
+
+/* input event queue registers; code == ((HIGH << 8) | LOW) */
+#define DM355EVM_MSP_INPUT_COUNT 0x16 /* decrement by reading LOW */
+#define DM355EVM_MSP_INPUT_HIGH 0x17
+#define DM355EVM_MSP_INPUT_LOW 0x18
+
+#endif /* __LINUX_I2C_DM355EVM_MSP */
diff --git a/include/linux/i2c/twl4030.h b/include/linux/i2c/twl4030.h
index fb604dcd38f..a8f84c01f82 100644
--- a/include/linux/i2c/twl4030.h
+++ b/include/linux/i2c/twl4030.h
@@ -78,8 +78,8 @@ int twl4030_i2c_read_u8(u8 mod_no, u8 *val, u8 reg);
* IMPORTANT: For twl4030_i2c_write(), allocate num_bytes + 1
* for the value, and populate your data starting at offset 1.
*/
-int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);
-int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);
+int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
+int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
/*----------------------------------------------------------------------*/
@@ -278,6 +278,18 @@ struct twl4030_platform_data {
struct twl4030_keypad_data *keypad;
struct twl4030_usb_data *usb;
+ /* LDO regulators */
+ struct regulator_init_data *vdac;
+ struct regulator_init_data *vpll1;
+ struct regulator_init_data *vpll2;
+ struct regulator_init_data *vmmc1;
+ struct regulator_init_data *vmmc2;
+ struct regulator_init_data *vsim;
+ struct regulator_init_data *vaux1;
+ struct regulator_init_data *vaux2;
+ struct regulator_init_data *vaux3;
+ struct regulator_init_data *vaux4;
+
/* REVISIT more to come ... _nothing_ should be hard-wired */
};
@@ -285,33 +297,6 @@ struct twl4030_platform_data {
int twl4030_sih_setup(int module);
-/*
- * FIXME completely stop using TWL4030_IRQ_BASE ... instead, pass the
- * IRQ data to subsidiary devices using platform device resources.
- */
-
-/* IRQ information-need base */
-#include <mach/irqs.h>
-/* TWL4030 interrupts */
-
-/* #define TWL4030_MODIRQ_GPIO (TWL4030_IRQ_BASE + 0) */
-#define TWL4030_MODIRQ_KEYPAD (TWL4030_IRQ_BASE + 1)
-#define TWL4030_MODIRQ_BCI (TWL4030_IRQ_BASE + 2)
-#define TWL4030_MODIRQ_MADC (TWL4030_IRQ_BASE + 3)
-/* #define TWL4030_MODIRQ_USB (TWL4030_IRQ_BASE + 4) */
-/* #define TWL4030_MODIRQ_PWR (TWL4030_IRQ_BASE + 5) */
-
-#define TWL4030_PWRIRQ_PWRBTN (TWL4030_PWR_IRQ_BASE + 0)
-/* #define TWL4030_PWRIRQ_CHG_PRES (TWL4030_PWR_IRQ_BASE + 1) */
-/* #define TWL4030_PWRIRQ_USB_PRES (TWL4030_PWR_IRQ_BASE + 2) */
-/* #define TWL4030_PWRIRQ_RTC (TWL4030_PWR_IRQ_BASE + 3) */
-/* #define TWL4030_PWRIRQ_HOT_DIE (TWL4030_PWR_IRQ_BASE + 4) */
-/* #define TWL4030_PWRIRQ_PWROK_TIMEOUT (TWL4030_PWR_IRQ_BASE + 5) */
-/* #define TWL4030_PWRIRQ_MBCHG (TWL4030_PWR_IRQ_BASE + 6) */
-/* #define TWL4030_PWRIRQ_SC_DETECT (TWL4030_PWR_IRQ_BASE + 7) */
-
-/* Rest are unsued currently*/
-
/* Offsets to Power Registers */
#define TWL4030_VDAC_DEV_GRP 0x3B
#define TWL4030_VDAC_DEDICATED 0x3E
@@ -322,10 +307,6 @@ int twl4030_sih_setup(int module);
#define TWL4030_VAUX3_DEV_GRP 0x1F
#define TWL4030_VAUX3_DEDICATED 0x22
-/* TWL4030 GPIO interrupt definitions */
-
-#define TWL4030_GPIO_IRQ_NO(n) (TWL4030_GPIO_IRQ_BASE + (n))
-
/*
* Exported TWL4030 GPIO APIs
*
@@ -340,4 +321,38 @@ int twl4030_set_gpio_debounce(int gpio, int enable);
static inline int twl4030charger_usb_en(int enable) { return 0; }
#endif
+/*----------------------------------------------------------------------*/
+
+/* Linux-specific regulator identifiers ... for now, we only support
+ * the LDOs, and leave the three buck converters alone. VDD1 and VDD2
+ * need to tie into hardware based voltage scaling (cpufreq etc), while
+ * VIO is generally fixed.
+ */
+
+/* EXTERNAL dc-to-dc buck converters */
+#define TWL4030_REG_VDD1 0
+#define TWL4030_REG_VDD2 1
+#define TWL4030_REG_VIO 2
+
+/* EXTERNAL LDOs */
+#define TWL4030_REG_VDAC 3
+#define TWL4030_REG_VPLL1 4
+#define TWL4030_REG_VPLL2 5 /* not on all chips */
+#define TWL4030_REG_VMMC1 6
+#define TWL4030_REG_VMMC2 7 /* not on all chips */
+#define TWL4030_REG_VSIM 8 /* not on all chips */
+#define TWL4030_REG_VAUX1 9 /* not on all chips */
+#define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */
+#define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */
+#define TWL4030_REG_VAUX3 12 /* not on all chips */
+#define TWL4030_REG_VAUX4 13 /* not on all chips */
+
+/* INTERNAL LDOs */
+#define TWL4030_REG_VINTANA1 14
+#define TWL4030_REG_VINTANA2 15
+#define TWL4030_REG_VINTDIG 16
+#define TWL4030_REG_VUSB1V5 17
+#define TWL4030_REG_VUSB1V8 18
+#define TWL4030_REG_VUSB3V1 19
+
#endif /* End of __TWL4030_H */
diff --git a/include/linux/mfd/da903x.h b/include/linux/mfd/da903x.h
index cad314c1243..115dbe96508 100644
--- a/include/linux/mfd/da903x.h
+++ b/include/linux/mfd/da903x.h
@@ -32,6 +32,7 @@ enum {
DA9030_ID_LDO18,
DA9030_ID_LDO19,
DA9030_ID_LDO_INT, /* LDO Internal */
+ DA9030_ID_BAT, /* battery charger */
DA9034_ID_LED_1,
DA9034_ID_LED_2,
@@ -93,6 +94,43 @@ struct da9034_touch_pdata {
int y_inverted;
};
+/* DA9030 battery charger data */
+struct power_supply_info;
+
+struct da9030_battery_info {
+ /* battery parameters */
+ struct power_supply_info *battery_info;
+
+ /* current and voltage to use for battery charging */
+ unsigned int charge_milliamp;
+ unsigned int charge_millivolt;
+
+ /* voltage thresholds (in millivolts) */
+ int vbat_low;
+ int vbat_crit;
+ int vbat_charge_start;
+ int vbat_charge_stop;
+ int vbat_charge_restart;
+
+ /* battery nominal minimal and maximal voltages in millivolts */
+ int vcharge_min;
+ int vcharge_max;
+
+ /* Temperature thresholds. These are DA9030 register values
+ "as is" and should be measured for each battery type */
+ int tbat_low;
+ int tbat_high;
+ int tbat_restart;
+
+
+ /* battery monitor interval (seconds) */
+ unsigned int batmon_interval;
+
+ /* platform callbacks for battery low and critical events */
+ void (*battery_low)(void);
+ void (*battery_critical)(void);
+};
+
struct da903x_subdev_info {
int id;
const char *name;
@@ -190,11 +228,13 @@ extern int da903x_unregister_notifier(struct device *dev,
extern int da903x_query_status(struct device *dev, unsigned int status);
-/* NOTE: the two functions below are not intended for use outside
- * of the DA9034 sub-device drivers
+/* NOTE: the functions below are not intended for use outside
+ * of the DA903x sub-device drivers
*/
extern int da903x_write(struct device *dev, int reg, uint8_t val);
+extern int da903x_writes(struct device *dev, int reg, int len, uint8_t *val);
extern int da903x_read(struct device *dev, int reg, uint8_t *val);
+extern int da903x_reads(struct device *dev, int reg, int len, uint8_t *val);
extern int da903x_update(struct device *dev, int reg, uint8_t val, uint8_t mask);
extern int da903x_set_bits(struct device *dev, int reg, uint8_t bit_mask);
extern int da903x_clr_bits(struct device *dev, int reg, uint8_t bit_mask);
diff --git a/include/linux/mfd/wm8350/comparator.h b/include/linux/mfd/wm8350/comparator.h
index 05378864945..54bc5d0fd50 100644
--- a/include/linux/mfd/wm8350/comparator.h
+++ b/include/linux/mfd/wm8350/comparator.h
@@ -164,4 +164,12 @@
#define WM8350_AUXADC_BATT 6
#define WM8350_AUXADC_TEMP 7
+struct wm8350;
+
+/*
+ * AUX ADC Readback
+ */
+int wm8350_read_auxadc(struct wm8350 *wm8350, int channel, int scale,
+ int vref);
+
#endif
diff --git a/include/linux/mfd/wm8350/core.h b/include/linux/mfd/wm8350/core.h
index 6ebf97f2a47..980669d50dc 100644
--- a/include/linux/mfd/wm8350/core.h
+++ b/include/linux/mfd/wm8350/core.h
@@ -29,6 +29,7 @@
*/
#define WM8350_RESET_ID 0x00
#define WM8350_ID 0x01
+#define WM8350_REVISION 0x02
#define WM8350_SYSTEM_CONTROL_1 0x03
#define WM8350_SYSTEM_CONTROL_2 0x04
#define WM8350_SYSTEM_HIBERNATE 0x05
@@ -57,6 +58,10 @@
#define WM8350_OVER_CURRENT_INT_STATUS_MASK 0x25
#define WM8350_GPIO_INT_STATUS_MASK 0x26
#define WM8350_COMPARATOR_INT_STATUS_MASK 0x27
+#define WM8350_CHARGER_OVERRIDES 0xE2
+#define WM8350_MISC_OVERRIDES 0xE3
+#define WM8350_COMPARATOR_OVERRIDES 0xE7
+#define WM8350_STATE_MACHINE_STATUS 0xE9
#define WM8350_MAX_REGISTER 0xFF
@@ -77,6 +82,11 @@
#define WM8350_CUST_ID_MASK 0x00FF
/*
+ * R2 (0x02) - Revision
+ */
+#define WM8350_MASK_REV_MASK 0x00FF
+
+/*
* R3 (0x03) - System Control 1
*/
#define WM8350_CHIP_ON 0x8000
@@ -523,6 +533,35 @@
#define WM8350_DC2_STS 0x0002
#define WM8350_DC1_STS 0x0001
+/*
+ * R226 (0xE2) - Charger status
+ */
+#define WM8350_CHG_BATT_HOT_OVRDE 0x8000
+#define WM8350_CHG_BATT_COLD_OVRDE 0x4000
+
+/*
+ * R227 (0xE3) - Misc Overrides
+ */
+#define WM8350_USB_LIMIT_OVRDE 0x0400
+
+/*
+ * R227 (0xE7) - Comparator Overrides
+ */
+#define WM8350_USB_FB_OVRDE 0x8000
+#define WM8350_WALL_FB_OVRDE 0x4000
+#define WM8350_BATT_FB_OVRDE 0x2000
+
+
+/*
+ * R233 (0xE9) - State Machinine Status
+ */
+#define WM8350_USB_SM_MASK 0x0700
+#define WM8350_USB_SM_SHIFT 8
+
+#define WM8350_USB_SM_100_SLV 1
+#define WM8350_USB_SM_500_SLV 5
+#define WM8350_USB_SM_STDBY_SLV 7
+
/* WM8350 wake up conditions */
#define WM8350_IRQ_WKUP_OFF_STATE 43
#define WM8350_IRQ_WKUP_HIB_STATE 44
@@ -536,6 +575,7 @@
#define WM8350_REV_E 0x4
#define WM8350_REV_F 0x5
#define WM8350_REV_G 0x6
+#define WM8350_REV_H 0x7
#define WM8350_NUM_IRQ 63
@@ -549,6 +589,14 @@ extern const u16 wm8350_mode0_defaults[];
extern const u16 wm8350_mode1_defaults[];
extern const u16 wm8350_mode2_defaults[];
extern const u16 wm8350_mode3_defaults[];
+extern const u16 wm8351_mode0_defaults[];
+extern const u16 wm8351_mode1_defaults[];
+extern const u16 wm8351_mode2_defaults[];
+extern const u16 wm8351_mode3_defaults[];
+extern const u16 wm8352_mode0_defaults[];
+extern const u16 wm8352_mode1_defaults[];
+extern const u16 wm8352_mode2_defaults[];
+extern const u16 wm8352_mode3_defaults[];
struct wm8350;
@@ -558,8 +606,6 @@ struct wm8350_irq {
};
struct wm8350 {
- int rev; /* chip revision */
-
struct device *dev;
/* device IO */
@@ -572,6 +618,8 @@ struct wm8350 {
void *src);
u16 *reg_cache;
+ struct mutex auxadc_mutex;
+
/* Interrupt handling */
struct work_struct irq_work;
struct mutex irq_mutex; /* IRQ table mutex */
diff --git a/include/linux/mfd/wm8350/pmic.h b/include/linux/mfd/wm8350/pmic.h
index 69b69e07f62..96acbfc8aa1 100644
--- a/include/linux/mfd/wm8350/pmic.h
+++ b/include/linux/mfd/wm8350/pmic.h
@@ -701,6 +701,10 @@ struct platform_device;
struct regulator_init_data;
struct wm8350_pmic {
+ /* Number of regulators of each type on this device */
+ int max_dcdc;
+ int max_isink;
+
/* ISINK to DCDC mapping */
int isink_A_dcdc;
int isink_B_dcdc;
diff --git a/include/linux/mfd/wm8350/supply.h b/include/linux/mfd/wm8350/supply.h
index 1c8f3cde79b..2b9479310bb 100644
--- a/include/linux/mfd/wm8350/supply.h
+++ b/include/linux/mfd/wm8350/supply.h
@@ -13,7 +13,8 @@
#ifndef __LINUX_MFD_WM8350_SUPPLY_H_
#define __LINUX_MFD_WM8350_SUPPLY_H_
-#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/power_supply.h>
/*
* Charger registers
@@ -104,8 +105,30 @@
#define WM8350_IRQ_EXT_WALL_FB 37
#define WM8350_IRQ_EXT_BAT_FB 38
+/*
+ * Policy to control charger state machine.
+ */
+struct wm8350_charger_policy {
+
+ /* charger state machine policy - set in machine driver */
+ int eoc_mA; /* end of charge current (mA) */
+ int charge_mV; /* charge voltage */
+ int fast_limit_mA; /* fast charge current limit */
+ int fast_limit_USB_mA; /* USB fast charge current limit */
+ int charge_timeout; /* charge timeout (mins) */
+ int trickle_start_mV; /* trickle charge starts at mV */
+ int trickle_charge_mA; /* trickle charge current */
+ int trickle_charge_USB_mA; /* USB trickle charge current */
+};
+
struct wm8350_power {
struct platform_device *pdev;
+ struct power_supply battery;
+ struct power_supply usb;
+ struct power_supply ac;
+ struct wm8350_charger_policy *policy;
+
+ int rev_g_coeff;
};
#endif
diff --git a/include/linux/power_supply.h b/include/linux/power_supply.h
index f9348cba6dc..8ff25e0e7f7 100644
--- a/include/linux/power_supply.h
+++ b/include/linux/power_supply.h
@@ -45,6 +45,7 @@ enum {
POWER_SUPPLY_HEALTH_DEAD,
POWER_SUPPLY_HEALTH_OVERVOLTAGE,
POWER_SUPPLY_HEALTH_UNSPEC_FAILURE,
+ POWER_SUPPLY_HEALTH_COLD,
};
enum {