diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 27 |
1 files changed, 21 insertions, 6 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 885898a40d1..5b7a3dadadd 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -217,8 +217,8 @@ struct ieee80211_chanctx_conf { * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS) * changed (currently only in P2P client mode, GO mode will be later) - * @BSS_CHANGED_DTIM_PERIOD: the DTIM period value was changed (set when - * it becomes valid, managed mode only) + * @BSS_CHANGED_BEACON_INFO: Data from the AP's beacon became available: + * currently dtim_period only is under consideration. * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed, * note that this is only called when it changes after the channel * context had been assigned. @@ -244,7 +244,7 @@ enum ieee80211_bss_change { BSS_CHANGED_PS = 1<<17, BSS_CHANGED_TXPOWER = 1<<18, BSS_CHANGED_P2P_PS = 1<<19, - BSS_CHANGED_DTIM_PERIOD = 1<<20, + BSS_CHANGED_BEACON_INFO = 1<<20, BSS_CHANGED_BANDWIDTH = 1<<21, /* when adding here, make sure to change ieee80211_reconfig */ @@ -288,7 +288,7 @@ enum ieee80211_rssi_event { * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag * @dtim_period: num of beacons before the next DTIM, for beaconing, * valid in station mode only if after the driver was notified - * with the %BSS_CHANGED_DTIM_PERIOD flag, will be non-zero then. + * with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then. * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old * as it may have been received during scanning long ago). If the * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can @@ -305,6 +305,7 @@ enum ieee80211_rssi_event { * @basic_rates: bitmap of basic rates, each bit stands for an * index into the rate table configured by the driver in * the current band. + * @beacon_rate: associated AP's beacon TX rate * @mcast_rate: per-band multicast rate index + 1 (0: disabled) * @bssid: The BSSID for this BSS * @enable_beacon: whether beaconing should be enabled or not @@ -352,6 +353,7 @@ struct ieee80211_bss_conf { u32 sync_device_ts; u8 sync_dtim_count; u32 basic_rates; + struct ieee80211_rate *beacon_rate; int mcast_rate[IEEE80211_NUM_BANDS]; u16 ht_operation_mode; s32 cqm_rssi_thold; @@ -460,6 +462,8 @@ struct ieee80211_bss_conf { * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it * would be fragmented by size (this is optional, only used for * monitor injection). + * @IEEE80211_TX_CTL_PS_RESPONSE: This frame is a response to a poll + * frame (PS-Poll or uAPSD). * * Note: If you have to add new flags to the enumeration, then don't * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary. @@ -495,6 +499,7 @@ enum mac80211_tx_control_flags { IEEE80211_TX_STATUS_EOSP = BIT(28), IEEE80211_TX_CTL_USE_MINRATE = BIT(29), IEEE80211_TX_CTL_DONTFRAG = BIT(30), + IEEE80211_TX_CTL_PS_RESPONSE = BIT(31), }; #define IEEE80211_TX_CTL_STBC_SHIFT 23 @@ -805,6 +810,7 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * on this subframe * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC * is stored in the @ampdu_delimiter_crc field) + * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3 */ enum mac80211_rx_flags { RX_FLAG_MMIC_ERROR = BIT(0), @@ -832,8 +838,11 @@ enum mac80211_rx_flags { RX_FLAG_80MHZ = BIT(23), RX_FLAG_80P80MHZ = BIT(24), RX_FLAG_160MHZ = BIT(25), + RX_FLAG_STBC_MASK = BIT(26) | BIT(27), }; +#define RX_FLAG_STBC_SHIFT 26 + /** * struct ieee80211_rx_status - receive status * @@ -850,6 +859,10 @@ enum mac80211_rx_flags { * @signal: signal strength when receiving this frame, either in dBm, in dB or * unspecified depending on the hardware capabilities flags * @IEEE80211_HW_SIGNAL_* + * @chains: bitmask of receive chains for which separate signal strength + * values were filled. + * @chain_signal: per-chain signal strength, in dBm (unlike @signal, doesn't + * support dB or unspecified units) * @antenna: antenna used * @rate_idx: index of data rate into band's supported rates or MCS index if * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT) @@ -881,6 +894,8 @@ struct ieee80211_rx_status { u8 band; u8 antenna; s8 signal; + u8 chains; + s8 chain_signal[IEEE80211_MAX_CHAINS]; u8 ampdu_delimiter_crc; u8 vendor_radiotap_align; u8 vendor_radiotap_oui[3]; @@ -1235,7 +1250,7 @@ enum ieee80211_sta_rx_bandwidth { * struct ieee80211_sta_rates - station rate selection table * * @rcu_head: RCU head used for freeing the table on update - * @rates: transmit rates/flags to be used by default. + * @rate: transmit rates/flags to be used by default. * Overriding entries per-packet is possible by using cb tx control. */ struct ieee80211_sta_rates { @@ -1276,7 +1291,7 @@ struct ieee80211_sta_rates { * notifications and capabilities. The value is only valid after * the station moves to associated state. * @smps_mode: current SMPS mode (off, static or dynamic) - * @tx_rates: rate control selection table + * @rates: rate control selection table */ struct ieee80211_sta { u32 supp_rates[IEEE80211_NUM_BANDS]; |