aboutsummaryrefslogtreecommitdiff
path: root/include/net/cfg80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/net/cfg80211.h')
-rw-r--r--include/net/cfg80211.h171
1 files changed, 144 insertions, 27 deletions
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 97b8b7c9b63..bcc9f448ec4 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -258,13 +258,9 @@ struct ieee80211_supported_band {
/**
* struct vif_params - describes virtual interface parameters
- * @mesh_id: mesh ID to use
- * @mesh_id_len: length of the mesh ID
* @use_4addr: use 4-address frames
*/
struct vif_params {
- u8 *mesh_id;
- int mesh_id_len;
int use_4addr;
};
@@ -424,6 +420,7 @@ struct station_parameters {
* @STATION_INFO_TX_RETRIES: @tx_retries filled
* @STATION_INFO_TX_FAILED: @tx_failed filled
* @STATION_INFO_RX_DROP_MISC: @rx_dropped_misc filled
+ * @STATION_INFO_SIGNAL_AVG: @signal_avg filled
*/
enum station_info_flags {
STATION_INFO_INACTIVE_TIME = 1<<0,
@@ -439,6 +436,7 @@ enum station_info_flags {
STATION_INFO_TX_RETRIES = 1<<10,
STATION_INFO_TX_FAILED = 1<<11,
STATION_INFO_RX_DROP_MISC = 1<<12,
+ STATION_INFO_SIGNAL_AVG = 1<<13,
};
/**
@@ -485,6 +483,7 @@ struct rate_info {
* @plid: mesh peer link id
* @plink_state: mesh peer link state
* @signal: signal strength of last received packet in dBm
+ * @signal_avg: signal strength average in dBm
* @txrate: current unicast bitrate to this station
* @rx_packets: packets received from this station
* @tx_packets: packets transmitted to this station
@@ -505,6 +504,7 @@ struct station_info {
u16 plid;
u8 plink_state;
s8 signal;
+ s8 signal_avg;
struct rate_info txrate;
u32 rx_packets;
u32 tx_packets;
@@ -605,6 +605,8 @@ struct mpath_info {
* (or NULL for no change)
* @basic_rates_len: number of basic rates
* @ap_isolate: do not forward packets between connected stations
+ * @ht_opmode: HT Operation mode
+ * (u16 = opmode, -1 = do not change)
*/
struct bss_parameters {
int use_cts_prot;
@@ -613,8 +615,14 @@ struct bss_parameters {
u8 *basic_rates;
u8 basic_rates_len;
int ap_isolate;
+ int ht_opmode;
};
+/*
+ * struct mesh_config - 802.11s mesh configuration
+ *
+ * These parameters can be changed while the mesh is active.
+ */
struct mesh_config {
/* Timeouts in ms */
/* Mesh plink management parameters */
@@ -624,6 +632,8 @@ struct mesh_config {
u16 dot11MeshMaxPeerLinks;
u8 dot11MeshMaxRetries;
u8 dot11MeshTTL;
+ /* ttl used in path selection information elements */
+ u8 element_ttl;
bool auto_open_plinks;
/* HWMP parameters */
u8 dot11MeshHWMPmaxPREQretries;
@@ -636,6 +646,26 @@ struct mesh_config {
};
/**
+ * struct mesh_setup - 802.11s mesh setup configuration
+ * @mesh_id: the mesh ID
+ * @mesh_id_len: length of the mesh ID, at least 1 and at most 32 bytes
+ * @path_sel_proto: which path selection protocol to use
+ * @path_metric: which metric to use
+ * @vendor_ie: vendor information elements (optional)
+ * @vendor_ie_len: length of vendor information elements
+ *
+ * These parameters are fixed when the mesh is created.
+ */
+struct mesh_setup {
+ const u8 *mesh_id;
+ u8 mesh_id_len;
+ u8 path_sel_proto;
+ u8 path_metric;
+ const u8 *vendor_ie;
+ u8 vendor_ie_len;
+};
+
+/**
* struct ieee80211_txq_params - TX queue parameters
* @queue: TX queue identifier (NL80211_TXQ_Q_*)
* @txop: Maximum burst time in units of 32 usecs, 0 meaning disabled
@@ -923,6 +953,7 @@ struct cfg80211_disassoc_request {
* @privacy: this is a protected network, keys will be configured
* after joining
* @basic_rates: bitmap of basic rates to use when creating the IBSS
+ * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
*/
struct cfg80211_ibss_params {
u8 *ssid;
@@ -934,6 +965,7 @@ struct cfg80211_ibss_params {
u32 basic_rates;
bool channel_fixed;
bool privacy;
+ int mcast_rate[IEEE80211_NUM_BANDS];
};
/**
@@ -1029,7 +1061,8 @@ struct cfg80211_pmksa {
*
* @add_virtual_intf: create a new virtual interface with the given name,
* must set the struct wireless_dev's iftype. Beware: You must create
- * the new netdev in the wiphy's network namespace!
+ * the new netdev in the wiphy's network namespace! Returns the netdev,
+ * or an ERR_PTR.
*
* @del_virtual_intf: remove the virtual interface determined by ifindex.
*
@@ -1071,9 +1104,9 @@ struct cfg80211_pmksa {
* @get_mpath: get a mesh path for the given parameters
* @dump_mpath: dump mesh path callback -- resume dump at index @idx
*
- * @get_mesh_params: Put the current mesh parameters into *params
+ * @get_mesh_config: Get the current mesh configuration
*
- * @set_mesh_params: Set mesh parameters.
+ * @update_mesh_config: Update mesh parameters on a running mesh.
* The mask is a bitfield which tells us which parameters to
* set, and which to leave alone.
*
@@ -1132,7 +1165,9 @@ struct cfg80211_pmksa {
* @cancel_remain_on_channel: Cancel an on-going remain-on-channel operation.
* This allows the operation to be terminated prior to timeout based on
* the duration value.
- * @mgmt_tx: Transmit a management frame
+ * @mgmt_tx: Transmit a management frame.
+ * @mgmt_tx_cancel_wait: Cancel the wait time from transmitting a management
+ * frame on another channel
*
* @testmode_cmd: run a test mode command
*
@@ -1150,14 +1185,23 @@ struct cfg80211_pmksa {
* @mgmt_frame_register: Notify driver that a management frame type was
* registered. Note that this callback may not sleep, and cannot run
* concurrently with itself.
+ *
+ * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
+ * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
+ * reject TX/RX mask combinations they cannot support by returning -EINVAL
+ * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
+ *
+ * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
*/
struct cfg80211_ops {
int (*suspend)(struct wiphy *wiphy);
int (*resume)(struct wiphy *wiphy);
- int (*add_virtual_intf)(struct wiphy *wiphy, char *name,
- enum nl80211_iftype type, u32 *flags,
- struct vif_params *params);
+ struct net_device * (*add_virtual_intf)(struct wiphy *wiphy,
+ char *name,
+ enum nl80211_iftype type,
+ u32 *flags,
+ struct vif_params *params);
int (*del_virtual_intf)(struct wiphy *wiphy, struct net_device *dev);
int (*change_virtual_intf)(struct wiphy *wiphy,
struct net_device *dev,
@@ -1175,7 +1219,7 @@ struct cfg80211_ops {
u8 key_index, bool pairwise, const u8 *mac_addr);
int (*set_default_key)(struct wiphy *wiphy,
struct net_device *netdev,
- u8 key_index);
+ u8 key_index, bool unicast, bool multicast);
int (*set_default_mgmt_key)(struct wiphy *wiphy,
struct net_device *netdev,
u8 key_index);
@@ -1210,12 +1254,17 @@ struct cfg80211_ops {
int (*dump_mpath)(struct wiphy *wiphy, struct net_device *dev,
int idx, u8 *dst, u8 *next_hop,
struct mpath_info *pinfo);
- int (*get_mesh_params)(struct wiphy *wiphy,
+ int (*get_mesh_config)(struct wiphy *wiphy,
struct net_device *dev,
struct mesh_config *conf);
- int (*set_mesh_params)(struct wiphy *wiphy,
- struct net_device *dev,
- const struct mesh_config *nconf, u32 mask);
+ int (*update_mesh_config)(struct wiphy *wiphy,
+ struct net_device *dev, u32 mask,
+ const struct mesh_config *nconf);
+ int (*join_mesh)(struct wiphy *wiphy, struct net_device *dev,
+ const struct mesh_config *conf,
+ const struct mesh_setup *setup);
+ int (*leave_mesh)(struct wiphy *wiphy, struct net_device *dev);
+
int (*change_bss)(struct wiphy *wiphy, struct net_device *dev,
struct bss_parameters *params);
@@ -1289,10 +1338,13 @@ struct cfg80211_ops {
u64 cookie);
int (*mgmt_tx)(struct wiphy *wiphy, struct net_device *dev,
- struct ieee80211_channel *chan,
+ struct ieee80211_channel *chan, bool offchan,
enum nl80211_channel_type channel_type,
- bool channel_type_valid,
+ bool channel_type_valid, unsigned int wait,
const u8 *buf, size_t len, u64 *cookie);
+ int (*mgmt_tx_cancel_wait)(struct wiphy *wiphy,
+ struct net_device *dev,
+ u64 cookie);
int (*set_power_mgmt)(struct wiphy *wiphy, struct net_device *dev,
bool enabled, int timeout);
@@ -1304,6 +1356,9 @@ struct cfg80211_ops {
void (*mgmt_frame_register)(struct wiphy *wiphy,
struct net_device *dev,
u16 frame_type, bool reg);
+
+ int (*set_antenna)(struct wiphy *wiphy, u32 tx_ant, u32 rx_ant);
+ int (*get_antenna)(struct wiphy *wiphy, u32 *tx_ant, u32 *rx_ant);
};
/*
@@ -1321,13 +1376,14 @@ struct cfg80211_ops {
* initiator is %REGDOM_SET_BY_CORE).
* @WIPHY_FLAG_STRICT_REGULATORY: tells us the driver for this device will
* ignore regulatory domain settings until it gets its own regulatory
- * domain via its regulatory_hint(). After its gets its own regulatory
- * domain it will only allow further regulatory domain settings to
- * further enhance compliance. For example if channel 13 and 14 are
- * disabled by this regulatory domain no user regulatory domain can
- * enable these channels at a later time. This can be used for devices
- * which do not have calibration information gauranteed for frequencies
- * or settings outside of its regulatory domain.
+ * domain via its regulatory_hint() unless the regulatory hint is
+ * from a country IE. After its gets its own regulatory domain it will
+ * only allow further regulatory domain settings to further enhance
+ * compliance. For example if channel 13 and 14 are disabled by this
+ * regulatory domain no user regulatory domain can enable these channels
+ * at a later time. This can be used for devices which do not have
+ * calibration information guaranteed for frequencies or settings
+ * outside of its regulatory domain.
* @WIPHY_FLAG_DISABLE_BEACON_HINTS: enable this if your driver needs to ensure
* that passive scan flags and beaconing flags may not be lifted by
* cfg80211 due to regulatory beacon hints. For more information on beacon
@@ -1345,6 +1401,8 @@ struct cfg80211_ops {
* control port protocol ethertype. The device also honours the
* control_port_no_encrypt flag.
* @WIPHY_FLAG_IBSS_RSN: The device supports IBSS RSN.
+ * @WIPHY_FLAG_SUPPORTS_SEPARATE_DEFAULT_KEYS: The device supports separate
+ * unicast and multicast TX keys.
*/
enum wiphy_flags {
WIPHY_FLAG_CUSTOM_REGULATORY = BIT(0),
@@ -1356,6 +1414,7 @@ enum wiphy_flags {
WIPHY_FLAG_4ADDR_STATION = BIT(6),
WIPHY_FLAG_CONTROL_PORT_PROTOCOL = BIT(7),
WIPHY_FLAG_IBSS_RSN = BIT(8),
+ WIPHY_FLAG_SUPPORTS_SEPARATE_DEFAULT_KEYS= BIT(9),
};
struct mac_address {
@@ -1368,7 +1427,9 @@ struct ieee80211_txrx_stypes {
/**
* struct wiphy - wireless hardware description
- * @reg_notifier: the driver's regulatory notification callback
+ * @reg_notifier: the driver's regulatory notification callback,
+ * note that if your driver uses wiphy_apply_custom_regulatory()
+ * the reg_notifier's request can be passed as NULL
* @regd: the driver's regulatory domain, if one was requested via
* the regulatory_hint() API. This can be used by the driver
* on the reg_notifier() if it chooses to ignore future
@@ -1420,6 +1481,17 @@ struct ieee80211_txrx_stypes {
* @mgmt_stypes: bitmasks of frame subtypes that can be subscribed to or
* transmitted through nl80211, points to an array indexed by interface
* type
+ *
+ * @available_antennas_tx: bitmap of antennas which are available to be
+ * configured as TX antennas. Antenna configuration commands will be
+ * rejected unless this or @available_antennas_rx is set.
+ *
+ * @available_antennas_rx: bitmap of antennas which are available to be
+ * configured as RX antennas. Antenna configuration commands will be
+ * rejected unless this or @available_antennas_tx is set.
+ *
+ * @max_remain_on_channel_duration: Maximum time a remain-on-channel operation
+ * may request, if implemented.
*/
struct wiphy {
/* assign these fields before you register the wiphy */
@@ -1457,8 +1529,13 @@ struct wiphy {
char fw_version[ETHTOOL_BUSINFO_LEN];
u32 hw_version;
+ u16 max_remain_on_channel_duration;
+
u8 max_num_pmkids;
+ u32 available_antennas_tx;
+ u32 available_antennas_rx;
+
/* If multiple wiphys are registered and you're handed e.g.
* a regular netdev with assigned ieee80211_ptr, you won't
* know whether it points to a wiphy your driver has registered
@@ -1624,6 +1701,8 @@ struct cfg80211_cached_keys;
* @bssid: (private) Used by the internal configuration code
* @ssid: (private) Used by the internal configuration code
* @ssid_len: (private) Used by the internal configuration code
+ * @mesh_id_len: (private) Used by the internal configuration code
+ * @mesh_id_up_len: (private) Used by the internal configuration code
* @wext: (private) Used by the internal wireless extensions compat code
* @use_4addr: indicates 4addr mode is used on this interface, must be
* set by driver (if supported) on add_interface BEFORE registering the
@@ -1653,7 +1732,7 @@ struct wireless_dev {
/* currently used for IBSS and SME - might be rearranged later */
u8 ssid[IEEE80211_MAX_SSID_LEN];
- u8 ssid_len;
+ u8 ssid_len, mesh_id_len, mesh_id_up_len;
enum {
CFG80211_SME_IDLE,
CFG80211_SME_CONNECTING,
@@ -2297,6 +2376,32 @@ void __cfg80211_send_disassoc(struct net_device *dev, const u8 *buf,
size_t len);
/**
+ * cfg80211_send_unprot_deauth - notification of unprotected deauthentication
+ * @dev: network device
+ * @buf: deauthentication frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever a received Deauthentication frame has been
+ * dropped in station mode because of MFP being used but the Deauthentication
+ * frame was not protected. This function may sleep.
+ */
+void cfg80211_send_unprot_deauth(struct net_device *dev, const u8 *buf,
+ size_t len);
+
+/**
+ * cfg80211_send_unprot_disassoc - notification of unprotected disassociation
+ * @dev: network device
+ * @buf: disassociation frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever a received Disassociation frame has been
+ * dropped in station mode because of MFP being used but the Disassociation
+ * frame was not protected. This function may sleep.
+ */
+void cfg80211_send_unprot_disassoc(struct net_device *dev, const u8 *buf,
+ size_t len);
+
+/**
* cfg80211_michael_mic_failure - notification of Michael MIC failure (TKIP)
* @dev: network device
* @addr: The source MAC address of the frame
@@ -2595,6 +2700,18 @@ void cfg80211_cqm_rssi_notify(struct net_device *dev,
enum nl80211_cqm_rssi_threshold_event rssi_event,
gfp_t gfp);
+/**
+ * cfg80211_cqm_pktloss_notify - notify userspace about packetloss to peer
+ * @dev: network device
+ * @peer: peer's MAC address
+ * @num_packets: how many packets were lost -- should be a fixed threshold
+ * but probably no less than maybe 50, or maybe a throughput dependent
+ * threshold (to account for temporary interference)
+ * @gfp: context flags
+ */
+void cfg80211_cqm_pktloss_notify(struct net_device *dev,
+ const u8 *peer, u32 num_packets, gfp_t gfp);
+
/* Logging, debugging and troubleshooting/diagnostic helpers. */
/* wiphy_printk helpers, similar to dev_printk */
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-28 06:22:10 +0000