diff options
Diffstat (limited to 'include/media/v4l2-common.h')
| -rw-r--r-- | include/media/v4l2-common.h | 65 |
1 files changed, 48 insertions, 17 deletions
diff --git a/include/media/v4l2-common.h b/include/media/v4l2-common.h index d4030a7e16e..642520acdfa 100644 --- a/include/media/v4l2-common.h +++ b/include/media/v4l2-common.h @@ -58,6 +58,9 @@ /* Prints the ioctl in a human-readable format */ extern void v4l_printk_ioctl(unsigned int cmd); +/* Prints the ioctl and arg in a human-readable format */ +extern void v4l_printk_ioctl_arg(char *s,unsigned int cmd, void *arg); + /* Use this macro for non-I2C drivers. Pass the driver name as the first arg. */ #define v4l_print_ioctl(name, cmd) \ do { \ @@ -100,6 +103,7 @@ enum v4l2_chip_ident { V4L2_IDENT_UNKNOWN = 0, /* module saa7115: reserved range 100-149 */ + V4L2_IDENT_SAA7113 = 103, V4L2_IDENT_SAA7114 = 104, V4L2_IDENT_SAA7115 = 105, @@ -115,25 +119,30 @@ enum v4l2_chip_ident { }; /* audio ioctls */ -/* v4l device was opened in Radio mode */ -#define AUDC_SET_RADIO _IO('d',88) -/* select from TV,radio,extern,MUTE */ -#define AUDC_SET_INPUT _IOW('d',89,int) -/* msp3400 ioctl: will be removed in the near future */ -struct msp_matrix { - int input; - int output; -}; -#define MSP_SET_MATRIX _IOW('m',17,struct msp_matrix) +/* v4l device was opened in Radio mode, to be replaced by VIDIOC_INT_S_TUNER_MODE */ +#define AUDC_SET_RADIO _IO('d',88) /* tuner ioctls */ + /* Sets tuner type and its I2C addr */ -#define TUNER_SET_TYPE_ADDR _IOW('d',90,int) -/* Puts tuner on powersaving state, disabling it, except for i2c */ -#define TUNER_SET_STANDBY _IOW('d',91,int) +#define TUNER_SET_TYPE_ADDR _IOW('d', 90, int) + +/* Puts tuner on powersaving state, disabling it, except for i2c. To be replaced + by VIDIOC_INT_S_STANDBY. */ +#define TUNER_SET_STANDBY _IOW('d', 91, int) + /* Sets tda9887 specific stuff, like port1, port2 and qss */ -#define TDA9887_SET_CONFIG _IOW('d',92,int) +#define TDA9887_SET_CONFIG _IOW('d', 92, int) + +/* Switch the tuner to a specific tuner mode. Replacement of AUDC_SET_RADIO */ +#define VIDIOC_INT_S_TUNER_MODE _IOW('d', 93, enum v4l2_tuner_type) + +/* Generic standby command. Passing -1 (all bits set to 1) will put the whole + chip into standby mode, value 0 will make the chip fully active. Specific + bits can be used by certain chips to enable/disable specific subsystems. + Replacement of TUNER_SET_STANDBY. */ +#define VIDIOC_INT_S_STANDBY _IOW('d', 94, u32) /* only implemented if CONFIG_VIDEO_ADV_DEBUG is defined */ #define VIDIOC_INT_S_REGISTER _IOR ('d', 100, struct v4l2_register) @@ -160,7 +169,8 @@ struct msp_matrix { /* Used to generate VBI signals on a video signal. v4l2_sliced_vbi_data is filled with the data packets that should be output. Note that if you set - the line field to 0, then that VBI signal is disabled. */ + the line field to 0, then that VBI signal is disabled. If no + valid VBI data was found, then the type field is set to 0 on return. */ #define VIDIOC_INT_S_VBI_DATA _IOW ('d', 105, struct v4l2_sliced_vbi_data) /* Used to obtain the sliced VBI packet from a readback register. Not all @@ -168,11 +178,11 @@ struct msp_matrix { register contains invalid or erroneous data -EIO is returned. Note that you must fill in the 'id' member and the 'field' member (to determine whether CC data from the first or second field should be obtained). */ -#define VIDIOC_INT_G_VBI_DATA _IOWR('d', 106, struct v4l2_sliced_vbi_data *) +#define VIDIOC_INT_G_VBI_DATA _IOWR('d', 106, struct v4l2_sliced_vbi_data) /* Returns the chip identifier or V4L2_IDENT_UNKNOWN if no identification can be made. */ -#define VIDIOC_INT_G_CHIP_IDENT _IOR ('d', 107, enum v4l2_chip_ident *) +#define VIDIOC_INT_G_CHIP_IDENT _IOR ('d', 107, enum v4l2_chip_ident) /* Sets I2S speed in bps. This is used to provide a standard way to select I2S clock used by driving digital audio streams at some board designs. @@ -180,4 +190,25 @@ struct msp_matrix { If the frequency is not supported, then -EINVAL is returned. */ #define VIDIOC_INT_I2S_CLOCK_FREQ _IOW ('d', 108, u32) +/* Routing definition, device dependent. It specifies which inputs (if any) + should be routed to which outputs (if any). */ +struct v4l2_routing { + u32 input; + u32 output; +}; + +/* These internal commands should be used to define the inputs and outputs + of an audio/video chip. They will replace the v4l2 API commands + VIDIOC_S/G_INPUT, VIDIOC_S/G_OUTPUT, VIDIOC_S/G_AUDIO and VIDIOC_S/G_AUDOUT + that are meant to be used by the user. + The internal commands should be used to switch inputs/outputs + because only the driver knows how to map a 'Television' input to the precise + input/output routing of an A/D converter, or a DSP, or a video digitizer. + These four commands should only be sent directly to an i2c device, they + should not be broadcast as the routing is very device specific. */ +#define VIDIOC_INT_S_AUDIO_ROUTING _IOW ('d', 109, struct v4l2_routing) +#define VIDIOC_INT_G_AUDIO_ROUTING _IOR ('d', 110, struct v4l2_routing) +#define VIDIOC_INT_S_VIDEO_ROUTING _IOW ('d', 111, struct v4l2_routing) +#define VIDIOC_INT_G_VIDEO_ROUTING _IOR ('d', 112, struct v4l2_routing) + #endif /* V4L2_COMMON_H_ */ |