diff options
Diffstat (limited to 'include/asm-mips/sn/sn0/addrs.h')
| -rw-r--r-- | include/asm-mips/sn/sn0/addrs.h | 364 |
1 files changed, 364 insertions, 0 deletions
diff --git a/include/asm-mips/sn/sn0/addrs.h b/include/asm-mips/sn/sn0/addrs.h new file mode 100644 index 00000000000..398815639fb --- /dev/null +++ b/include/asm-mips/sn/sn0/addrs.h @@ -0,0 +1,364 @@ +/* + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Derived from IRIX <sys/SN/SN0/addrs.h>, revision 1.126. + * + * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. + * Copyright (C) 1999 by Ralf Baechle + */ +#ifndef _ASM_SN_SN0_ADDRS_H +#define _ASM_SN_SN0_ADDRS_H + +#include <linux/config.h> + +/* + * SN0 (on a T5) Address map + * + * This file contains a set of definitions and macros which are used + * to reference into the major address spaces (CAC, HSPEC, IO, MSPEC, + * and UNCAC) used by the SN0 architecture. It also contains addresses + * for "major" statically locatable PROM/Kernel data structures, such as + * the partition table, the configuration data structure, etc. + * We make an implicit assumption that the processor using this file + * follows the R10K's provisions for specifying uncached attributes; + * should this change, the base registers may very well become processor- + * dependent. + * + * For more information on the address spaces, see the "Local Resources" + * chapter of the Hub specification. + * + * NOTE: This header file is included both by C and by assembler source + * files. Please bracket any language-dependent definitions + * appropriately. + */ + +/* + * Some of the macros here need to be casted to appropriate types when used + * from C. They definitely must not be casted from assembly language so we + * use some new ANSI preprocessor stuff to paste these on where needed. + */ + +/* + * The following couple of definitions will eventually need to be variables, + * since the amount of address space assigned to each node depends on + * whether the system is running in N-mode (more nodes with less memory) + * or M-mode (fewer nodes with more memory). We expect that it will + * be a while before we need to make this decision dynamically, though, + * so for now we just use defines bracketed by an ifdef. + */ + +#ifdef CONFIG_SGI_SN0_N_MODE + +#define NODE_SIZE_BITS 31 +#define BWIN_SIZE_BITS 28 + +#define NASID_BITS 9 +#define NASID_BITMASK (0x1ffLL) +#define NASID_SHFT 31 +#define NASID_META_BITS 5 +#define NASID_LOCAL_BITS 4 + +#define BDDIR_UPPER_MASK (UINT64_CAST 0x7ffff << 10) +#define BDECC_UPPER_MASK (UINT64_CAST 0x3ffffff << 3) + +#else /* !defined(CONFIG_SGI_SN0_N_MODE), assume that M-mode is desired */ + +#define NODE_SIZE_BITS 32 +#define BWIN_SIZE_BITS 29 + +#define NASID_BITMASK (0xffLL) +#define NASID_BITS 8 +#define NASID_SHFT 32 +#define NASID_META_BITS 4 +#define NASID_LOCAL_BITS 4 + +#define BDDIR_UPPER_MASK (UINT64_CAST 0xfffff << 10) +#define BDECC_UPPER_MASK (UINT64_CAST 0x7ffffff << 3) + +#endif /* !defined(CONFIG_SGI_SN0_N_MODE) */ + +#define NODE_ADDRSPACE_SIZE (UINT64_CAST 1 << NODE_SIZE_BITS) + +#define NASID_MASK (UINT64_CAST NASID_BITMASK << NASID_SHFT) +#define NASID_GET(_pa) (int) ((UINT64_CAST (_pa) >> \ + NASID_SHFT) & NASID_BITMASK) + +#if !defined(__ASSEMBLY__) && !defined(_STANDALONE) + +#define NODE_SWIN_BASE(nasid, widget) \ + ((widget == 0) ? NODE_BWIN_BASE((nasid), SWIN0_BIGWIN) \ + : RAW_NODE_SWIN_BASE(nasid, widget)) +#else /* __ASSEMBLY__ || _STANDALONE */ +#define NODE_SWIN_BASE(nasid, widget) \ + (NODE_IO_BASE(nasid) + (UINT64_CAST (widget) << SWIN_SIZE_BITS)) +#endif /* __ASSEMBLY__ || _STANDALONE */ + +/* + * The following definitions pertain to the IO special address + * space. They define the location of the big and little windows + * of any given node. + */ + +#define BWIN_INDEX_BITS 3 +#define BWIN_SIZE (UINT64_CAST 1 << BWIN_SIZE_BITS) +#define BWIN_SIZEMASK (BWIN_SIZE - 1) +#define BWIN_WIDGET_MASK 0x7 +#define NODE_BWIN_BASE0(nasid) (NODE_IO_BASE(nasid) + BWIN_SIZE) +#define NODE_BWIN_BASE(nasid, bigwin) (NODE_BWIN_BASE0(nasid) + \ + (UINT64_CAST (bigwin) << BWIN_SIZE_BITS)) + +#define BWIN_WIDGETADDR(addr) ((addr) & BWIN_SIZEMASK) +#define BWIN_WINDOWNUM(addr) (((addr) >> BWIN_SIZE_BITS) & BWIN_WIDGET_MASK) +/* + * Verify if addr belongs to large window address of node with "nasid" + * + * + * NOTE: "addr" is expected to be XKPHYS address, and NOT physical + * address + * + * + */ + +#define NODE_BWIN_ADDR(nasid, addr) \ + (((addr) >= NODE_BWIN_BASE0(nasid)) && \ + ((addr) < (NODE_BWIN_BASE(nasid, HUB_NUM_BIG_WINDOW) + \ + BWIN_SIZE))) + +/* + * The following define the major position-independent aliases used + * in SN0. + * CALIAS -- Varies in size, points to the first n bytes of memory + * on the reader's node. + */ + +#define CALIAS_BASE CAC_BASE + + + +#define BRIDGE_REG_PTR(_base, _off) ((volatile bridgereg_t *) \ + ((__psunsigned_t)(_base) + (__psunsigned_t)(_off))) + +#define SN0_WIDGET_BASE(_nasid, _wid) (NODE_SWIN_BASE((_nasid), (_wid))) + +/* Turn on sable logging for the processors whose bits are set. */ +#ifdef SABLE +#define SABLE_LOG_TRIGGER(_map) \ + *((volatile hubreg_t *)(IO_BASE + 0x17ffff0)) = (_map) +#else +#define SABLE_LOG_TRIGGER(_map) +#endif /* SABLE */ + +#ifndef __ASSEMBLY__ +#define KERN_NMI_ADDR(nasid, slice) \ + TO_NODE_UNCAC((nasid), IP27_NMI_KREGS_OFFSET + \ + (IP27_NMI_KREGS_CPU_SIZE * (slice))) +#endif /* !__ASSEMBLY__ */ + +#ifdef PROM + +#define MISC_PROM_BASE PHYS_TO_K0(0x01300000) +#define MISC_PROM_SIZE 0x200000 + +#define DIAG_BASE PHYS_TO_K0(0x01500000) +#define DIAG_SIZE 0x300000 + +#define ROUTE_BASE PHYS_TO_K0(0x01800000) +#define ROUTE_SIZE 0x200000 + +#define IP27PROM_FLASH_HDR PHYS_TO_K0(0x01300000) +#define IP27PROM_FLASH_DATA PHYS_TO_K0(0x01301000) +#define IP27PROM_CORP_MAX 32 +#define IP27PROM_CORP PHYS_TO_K0(0x01800000) +#define IP27PROM_CORP_SIZE 0x10000 +#define IP27PROM_CORP_STK PHYS_TO_K0(0x01810000) +#define IP27PROM_CORP_STKSIZE 0x2000 +#define IP27PROM_DECOMP_BUF PHYS_TO_K0(0x01900000) +#define IP27PROM_DECOMP_SIZE 0xfff00 + +#define IP27PROM_BASE PHYS_TO_K0(0x01a00000) +#define IP27PROM_BASE_MAPPED (UNCAC_BASE | 0x1fc00000) +#define IP27PROM_SIZE_MAX 0x100000 + +#define IP27PROM_PCFG PHYS_TO_K0(0x01b00000) +#define IP27PROM_PCFG_SIZE 0xd0000 +#define IP27PROM_ERRDMP PHYS_TO_K1(0x01bd0000) +#define IP27PROM_ERRDMP_SIZE 0xf000 + +#define IP27PROM_INIT_START PHYS_TO_K1(0x01bd0000) +#define IP27PROM_CONSOLE PHYS_TO_K1(0x01bdf000) +#define IP27PROM_CONSOLE_SIZE 0x200 +#define IP27PROM_NETUART PHYS_TO_K1(0x01bdf200) +#define IP27PROM_NETUART_SIZE 0x100 +#define IP27PROM_UNUSED1 PHYS_TO_K1(0x01bdf300) +#define IP27PROM_UNUSED1_SIZE 0x500 +#define IP27PROM_ELSC_BASE_A PHYS_TO_K0(0x01bdf800) +#define IP27PROM_ELSC_BASE_B PHYS_TO_K0(0x01bdfc00) +#define IP27PROM_STACK_A PHYS_TO_K0(0x01be0000) +#define IP27PROM_STACK_B PHYS_TO_K0(0x01bf0000) +#define IP27PROM_STACK_SHFT 16 +#define IP27PROM_STACK_SIZE (1 << IP27PROM_STACK_SHFT) +#define IP27PROM_INIT_END PHYS_TO_K0(0x01c00000) + +#define SLAVESTACK_BASE PHYS_TO_K0(0x01580000) +#define SLAVESTACK_SIZE 0x40000 + +#define ENETBUFS_BASE PHYS_TO_K0(0x01f80000) +#define ENETBUFS_SIZE 0x20000 + +#define IO6PROM_BASE PHYS_TO_K0(0x01c00000) +#define IO6PROM_SIZE 0x400000 +#define IO6PROM_BASE_MAPPED (UNCAC_BASE | 0x11c00000) +#define IO6DPROM_BASE PHYS_TO_K0(0x01c00000) +#define IO6DPROM_SIZE 0x200000 + +#define NODEBUGUNIX_ADDR PHYS_TO_K0(0x00019000) +#define DEBUGUNIX_ADDR PHYS_TO_K0(0x00100000) + +#define IP27PROM_INT_LAUNCH 10 /* and 11 */ +#define IP27PROM_INT_NETUART 12 /* through 17 */ + +#endif /* PROM */ + +/* + * needed by symmon so it needs to be outside #if PROM + */ +#define IP27PROM_ELSC_SHFT 10 +#define IP27PROM_ELSC_SIZE (1 << IP27PROM_ELSC_SHFT) + +/* + * This address is used by IO6PROM to build MemoryDescriptors of + * free memory. This address is important since unix gets loaded + * at this address, and this memory has to be FREE if unix is to + * be loaded. + */ + +#define FREEMEM_BASE PHYS_TO_K0(0x2000000) + +#define IO6PROM_STACK_SHFT 14 /* stack per cpu */ +#define IO6PROM_STACK_SIZE (1 << IO6PROM_STACK_SHFT) + +/* + * IP27 PROM vectors + */ + +#define IP27PROM_ENTRY PHYS_TO_COMPATK1(0x1fc00000) +#define IP27PROM_RESTART PHYS_TO_COMPATK1(0x1fc00008) +#define IP27PROM_SLAVELOOP PHYS_TO_COMPATK1(0x1fc00010) +#define IP27PROM_PODMODE PHYS_TO_COMPATK1(0x1fc00018) +#define IP27PROM_IOC3UARTPOD PHYS_TO_COMPATK1(0x1fc00020) +#define IP27PROM_FLASHLEDS PHYS_TO_COMPATK1(0x1fc00028) +#define IP27PROM_REPOD PHYS_TO_COMPATK1(0x1fc00030) +#define IP27PROM_LAUNCHSLAVE PHYS_TO_COMPATK1(0x1fc00038) +#define IP27PROM_WAITSLAVE PHYS_TO_COMPATK1(0x1fc00040) +#define IP27PROM_POLLSLAVE PHYS_TO_COMPATK1(0x1fc00048) + +#define KL_UART_BASE LOCAL_HUB_ADDR(MD_UREG0_0) /* base of UART regs */ +#define KL_UART_CMD LOCAL_HUB_ADDR(MD_UREG0_0) /* UART command reg */ +#define KL_UART_DATA LOCAL_HUB_ADDR(MD_UREG0_1) /* UART data reg */ +#define KL_I2C_REG MD_UREG0_0 /* I2C reg */ + +#ifndef __ASSEMBLY__ + +/* Address 0x400 to 0x1000 ualias points to cache error eframe + misc + * CACHE_ERR_SP_PTR could either contain an address to the stack, or + * the stack could start at CACHE_ERR_SP_PTR + */ +#if defined (HUB_ERR_STS_WAR) +#define CACHE_ERR_EFRAME 0x480 +#else /* HUB_ERR_STS_WAR */ +#define CACHE_ERR_EFRAME 0x400 +#endif /* HUB_ERR_STS_WAR */ + +#define CACHE_ERR_ECCFRAME (CACHE_ERR_EFRAME + EF_SIZE) +#define CACHE_ERR_SP_PTR (0x1000 - 32) /* why -32? TBD */ +#define CACHE_ERR_IBASE_PTR (0x1000 - 40) +#define CACHE_ERR_SP (CACHE_ERR_SP_PTR - 16) +#define CACHE_ERR_AREA_SIZE (ARCS_SPB_OFFSET - CACHE_ERR_EFRAME) + +#endif /* !__ASSEMBLY__ */ + +#define _ARCSPROM + +#ifdef _STANDALONE + +/* + * The PROM needs to pass the device base address and the + * device pci cfg space address to the device drivers during + * install. The COMPONENT->Key field is used for this purpose. + * Macros needed by SN0 device drivers to convert the + * COMPONENT->Key field to the respective base address. + * Key field looks as follows: + * + * +----------------------------------------------------+ + * |devnasid | widget |pciid |hubwidid|hstnasid | adap | + * | 2 | 1 | 1 | 1 | 2 | 1 | + * +----------------------------------------------------+ + * | | | | | | | + * 64 48 40 32 24 8 0 + * + * These are used by standalone drivers till the io infrastructure + * is in place. + */ + +#ifndef __ASSEMBLY__ + +#define uchar unsigned char + +#define KEY_DEVNASID_SHFT 48 +#define KEY_WIDID_SHFT 40 +#define KEY_PCIID_SHFT 32 +#define KEY_HUBWID_SHFT 24 +#define KEY_HSTNASID_SHFT 8 + +#define MK_SN0_KEY(nasid, widid, pciid) \ + ((((__psunsigned_t)nasid)<< KEY_DEVNASID_SHFT |\ + ((__psunsigned_t)widid) << KEY_WIDID_SHFT) |\ + ((__psunsigned_t)pciid) << KEY_PCIID_SHFT) + +#define ADD_HUBWID_KEY(key,hubwid)\ + (key|=((__psunsigned_t)hubwid << KEY_HUBWID_SHFT)) + +#define ADD_HSTNASID_KEY(key,hstnasid)\ + (key|=((__psunsigned_t)hstnasid << KEY_HSTNASID_SHFT)) + +#define GET_DEVNASID_FROM_KEY(key) ((short)(key >> KEY_DEVNASID_SHFT)) +#define GET_WIDID_FROM_KEY(key) ((uchar)(key >> KEY_WIDID_SHFT)) +#define GET_PCIID_FROM_KEY(key) ((uchar)(key >> KEY_PCIID_SHFT)) +#define GET_HUBWID_FROM_KEY(key) ((uchar)(key >> KEY_HUBWID_SHFT)) +#define GET_HSTNASID_FROM_KEY(key) ((short)(key >> KEY_HSTNASID_SHFT)) + +#define PCI_64_TARGID_SHFT 60 + +#define GET_PCIBASE_FROM_KEY(key) (NODE_SWIN_BASE(GET_DEVNASID_FROM_KEY(key),\ + GET_WIDID_FROM_KEY(key))\ + | BRIDGE_DEVIO(GET_PCIID_FROM_KEY(key))) + +#define GET_PCICFGBASE_FROM_KEY(key) \ + (NODE_SWIN_BASE(GET_DEVNASID_FROM_KEY(key),\ + GET_WIDID_FROM_KEY(key))\ + | BRIDGE_TYPE0_CFG_DEV(GET_PCIID_FROM_KEY(key))) + +#define GET_WIDBASE_FROM_KEY(key) \ + (NODE_SWIN_BASE(GET_DEVNASID_FROM_KEY(key),\ + GET_WIDID_FROM_KEY(key))) + +#define PUT_INSTALL_STATUS(c,s) c->Revision = s +#define GET_INSTALL_STATUS(c) c->Revision + +#endif /* !__ASSEMBLY__ */ + +#endif /* _STANDALONE */ + +#if defined (HUB_ERR_STS_WAR) + +#define ERR_STS_WAR_REGISTER IIO_IIBUSERR +#define ERR_STS_WAR_ADDR LOCAL_HUB_ADDR(IIO_IIBUSERR) +#define ERR_STS_WAR_PHYSADDR TO_PHYS((__psunsigned_t)ERR_STS_WAR_ADDR) + /* Used to match addr in error reg. */ +#define OLD_ERR_STS_WAR_OFFSET ((MD_MEM_BANKS * MD_BANK_SIZE) - 0x100) + +#endif /* HUB_ERR_STS_WAR */ + +#endif /* _ASM_SN_SN0_ADDRS_H */ |