1 files changed, 209 insertions, 0 deletions
diff --git a/include/asm-m68knommu/m5249sim.h b/include/asm-m68knommu/m5249sim.h
new file mode 100644
index 00000000000..9344f529bd8
--- /dev/null
+++ b/include/asm-m68knommu/m5249sim.h
@@ -0,0 +1,209 @@
+/****************************************************************************/
+
+/*
+ *	m5249sim.h -- ColdFire 5249 System Integration Module support.
+ *
+ *	(C) Copyright 2002, Greg Ungerer (gerg@snapgear.com)
+ */
+
+/****************************************************************************/
+#ifndef	m5249sim_h
+#define	m5249sim_h
+/****************************************************************************/
+
+/*
+ *	Define the 5249 SIM register set addresses.
+ */
+#define	MCFSIM_RSR		0x00		/* Reset Status reg (r/w) */
+#define	MCFSIM_SYPCR		0x01		/* System Protection reg (r/w)*/
+#define	MCFSIM_SWIVR		0x02		/* SW Watchdog intr reg (r/w) */
+#define	MCFSIM_SWSR		0x03		/* SW Watchdog service (r/w) */
+#define	MCFSIM_PAR		0x04		/* Pin Assignment reg (r/w) */
+#define	MCFSIM_IRQPAR		0x06		/* Interrupt Assignment reg (r/w) */
+#define	MCFSIM_MPARK		0x0C		/* BUS Master Control Reg*/
+#define	MCFSIM_IPR		0x40		/* Interrupt Pend reg (r/w) */
+#define	MCFSIM_IMR		0x44		/* Interrupt Mask reg (r/w) */
+#define	MCFSIM_AVR		0x4b		/* Autovector Ctrl reg (r/w) */
+#define	MCFSIM_ICR0		0x4c		/* Intr Ctrl reg 0 (r/w) */
+#define	MCFSIM_ICR1		0x4d		/* Intr Ctrl reg 1 (r/w) */
+#define	MCFSIM_ICR2		0x4e		/* Intr Ctrl reg 2 (r/w) */
+#define	MCFSIM_ICR3		0x4f		/* Intr Ctrl reg 3 (r/w) */
+#define	MCFSIM_ICR4		0x50		/* Intr Ctrl reg 4 (r/w) */
+#define	MCFSIM_ICR5		0x51		/* Intr Ctrl reg 5 (r/w) */
+#define	MCFSIM_ICR6		0x52		/* Intr Ctrl reg 6 (r/w) */
+#define	MCFSIM_ICR7		0x53		/* Intr Ctrl reg 7 (r/w) */
+#define	MCFSIM_ICR8		0x54		/* Intr Ctrl reg 8 (r/w) */
+#define	MCFSIM_ICR9		0x55		/* Intr Ctrl reg 9 (r/w) */
+#define	MCFSIM_ICR10		0x56		/* Intr Ctrl reg 10 (r/w) */
+#define	MCFSIM_ICR11		0x57		/* Intr Ctrl reg 11 (r/w) */
+
+#define MCFSIM_CSAR0		0x80		/* CS 0 Address 0 reg (r/w) */
+#define MCFSIM_CSMR0		0x84		/* CS 0 Mask 0 reg (r/w) */
+#define MCFSIM_CSCR0		0x8a		/* CS 0 Control reg (r/w) */
+#define MCFSIM_CSAR1		0x8c		/* CS 1 Address reg (r/w) */
+#define MCFSIM_CSMR1		0x90		/* CS 1 Mask reg (r/w) */
+#define MCFSIM_CSCR1		0x96		/* CS 1 Control reg (r/w) */
+#define MCFSIM_CSAR2		0x98		/* CS 2 Adress reg (r/w) */
+#define MCFSIM_CSMR2		0x9c		/* CS 2 Mask reg (r/w) */
+#define MCFSIM_CSCR2		0xa2		/* CS 2 Control reg (r/w) */
+#define MCFSIM_CSAR3		0xa4		/* CS 3 Adress reg (r/w) */
+#define MCFSIM_CSMR3		0xa8		/* CS 3 Mask reg (r/w) */
+#define MCFSIM_CSCR3		0xae		/* CS 3 Control reg (r/w) */
+
+#define MCFSIM_DCR		0x100		/* DRAM Control reg (r/w) */
+#define MCFSIM_DACR0		0x108		/* DRAM 0 Addr and Ctrl (r/w) */
+#define MCFSIM_DMR0		0x10c		/* DRAM 0 Mask reg (r/w) */
+#define MCFSIM_DACR1		0x110		/* DRAM 1 Addr and Ctrl (r/w) */
+#define MCFSIM_DMR1		0x114		/* DRAM 1 Mask reg (r/w) */
+
+
+/*
+ *	Some symbol defines for the above...
+ */
+#define	MCFSIM_SWDICR		MCFSIM_ICR0	/* Watchdog timer ICR */
+#define	MCFSIM_TIMER1ICR	MCFSIM_ICR1	/* Timer 1 ICR */
+#define	MCFSIM_TIMER2ICR	MCFSIM_ICR2	/* Timer 2 ICR */
+#define	MCFSIM_UART1ICR		MCFSIM_ICR4	/* UART 1 ICR */
+#define	MCFSIM_UART2ICR		MCFSIM_ICR5	/* UART 2 ICR */
+#define	MCFSIM_DMA0ICR		MCFSIM_ICR6	/* DMA 0 ICR */
+#define	MCFSIM_DMA1ICR		MCFSIM_ICR7	/* DMA 1 ICR */
+#define	MCFSIM_DMA2ICR		MCFSIM_ICR8	/* DMA 2 ICR */
+#define	MCFSIM_DMA3ICR		MCFSIM_ICR9	/* DMA 3 ICR */
+
+/*
+ *	General purpose IO registers (in MBAR2).
+ */
+#define	MCFSIM2_GPIOREAD	0x0		/* GPIO read values */
+#define	MCFSIM2_GPIOWRITE	0x4		/* GPIO write values */
+#define	MCFSIM2_GPIOENABLE	0x8		/* GPIO enabled */
+#define	MCFSIM2_GPIOFUNC	0xc		/* GPIO function */
+#define	MCFSIM2_GPIO1READ	0xb0		/* GPIO1 read values */
+#define	MCFSIM2_GPIO1WRITE	0xb4		/* GPIO1 write values */
+#define	MCFSIM2_GPIO1ENABLE	0xb8		/* GPIO1 enabled */
+#define	MCFSIM2_GPIO1FUNC	0xbc		/* GPIO1 function */
+
+#define	MCFSIM2_GPIOINTSTAT	0xc0		/* GPIO interrupt status */
+#define	MCFSIM2_GPIOINTCLEAR	0xc0		/* GPIO interrupt clear */
+#define	MCFSIM2_GPIOINTENABLE	0xc4		/* GPIO interrupt enable */
+
+#define	MCFSIM2_INTLEVEL1	0x140		/* Interrupt level reg 1 */
+#define	MCFSIM2_INTLEVEL2	0x144		/* Interrupt level reg 2 */
+#define	MCFSIM2_INTLEVEL3	0x148		/* Interrupt level reg 3 */
+#define	MCFSIM2_INTLEVEL4	0x14c		/* Interrupt level reg 4 */
+#define	MCFSIM2_INTLEVEL5	0x150		/* Interrupt level reg 5 */
+#define	MCFSIM2_INTLEVEL6	0x154		/* Interrupt level reg 6 */
+#define	MCFSIM2_INTLEVEL7	0x158		/* Interrupt level reg 7 */
+#define	MCFSIM2_INTLEVEL8	0x15c		/* Interrupt level reg 8 */
+
+#define	MCFSIM2_DMAROUTE	0x188		/* DMA routing */
+
+#define	MCFSIM2_IDECONFIG1	0x18c		/* IDEconfig1 */
+#define	MCFSIM2_IDECONFIG2	0x190		/* IDEconfig2 */
+
+
+/*
+ *	Macro to set IMR register. It is 32 bits on the 5249.
+ */
+#define	MCFSIM_IMR_MASKALL	0x7fffe		/* All SIM intr sources */
+
+#define	mcf_getimr()		\
+	*((volatile unsigned long *) (MCF_MBAR + MCFSIM_IMR))
+
+#define	mcf_setimr(imr)		\
+	*((volatile unsigned long *) (MCF_MBAR + MCFSIM_IMR)) = (imr);
+
+#define	mcf_getipr()		\
+	*((volatile unsigned long *) (MCF_MBAR + MCFSIM_IPR))
+
+/****************************************************************************/
+
+#ifdef __ASSEMBLER__
+
+/*
+ *	The M5249C3 board needs a little help getting all its SIM devices
+ *	initialized at kernel start time. dBUG doesn't set much up, so
+ *	we need to do it manually.
+ */
+.macro m5249c3_setup
+	/*
+	 *	Set MBAR1 and MBAR2, just incase they are not set.
+	 */
+	movel	#0x10000001,%a0
+	movec	%a0,%MBAR			/* map MBAR region */
+	subql	#1,%a0				/* get MBAR address in a0 */
+
+	movel	#0x80000001,%a1
+	movec	%a1,#3086			/* map MBAR2 region */
+	subql	#1,%a1				/* get MBAR2 address in a1 */
+
+	/*
+	 *      Move secondary interrupts to base at 128.
+	 */
+	moveb	#0x80,%d0
+	moveb	%d0,0x16b(%a1)			/* interrupt base register */
+
+	/*
+	 *      Work around broken CSMR0/DRAM vector problem.
+	 */
+	movel	#0x001F0021,%d0			/* disable C/I bit */
+	movel	%d0,0x84(%a0)			/* set CSMR0 */
+
+	/*
+	 *	Disable the PLL firstly. (Who knows what state it is
+	 *	in here!).
+	 */
+	movel	0x180(%a1),%d0			/* get current PLL value */
+	andl	#0xfffffffe,%d0			/* PLL bypass first */
+	movel	%d0,0x180(%a1)			/* set PLL register */
+	nop
+
+#ifdef CONFIG_CLOCK_140MHz
+	/*
+	 *	Set initial clock frequency. This assumes M5249C3 board
+	 *	is fitted with 11.2896MHz crystal. It will program the
+	 *	PLL for 140MHz. Lets go fast :-)
+	 */
+	movel	#0x125a40f0,%d0			/* set for 140MHz */
+	movel	%d0,0x180(%a1)			/* set PLL register */
+	orl	#0x1,%d0
+	movel	%d0,0x180(%a1)			/* set PLL register */
+#endif
+
+	/*
+	 *	Setup CS1 for ethernet controller.
+	 *	(Setup as per M5249C3 doco).
+	 */
+	movel  #0xe0000000,%d0			/* CS1 mapped at 0xe0000000 */
+	movel  %d0,0x8c(%a0)
+	movel  #0x001f0021,%d0			/* CS1 size of 1Mb */
+	movel  %d0,0x90(%a0)
+	movew  #0x0080,%d0			/* CS1 = 16bit port, AA */
+	movew  %d0,0x96(%a0)
+
+	/*
+	 *	Setup CS2 for IDE interface.
+	 */
+	movel	#0x50000000,%d0			/* CS2 mapped at 0x50000000 */
+	movel	%d0,0x98(%a0)
+	movel	#0x001f0001,%d0			/* CS2 size of 1MB */
+	movel	%d0,0x9c(%a0)
+	movew	#0x0080,%d0			/* CS2 = 16bit, TA */
+	movew	%d0,0xa2(%a0)
+
+	movel	#0x00107000,%d0			/* IDEconfig1 */
+	movel	%d0,0x18c(%a1)
+	movel	#0x000c0400,%d0			/* IDEconfig2 */
+	movel	%d0,0x190(%a1)
+
+	movel	#0x00080000,%d0			/* GPIO19, IDE reset bit */
+	orl	%d0,0xc(%a1)			/* function GPIO19 */
+	orl	%d0,0x8(%a1)			/* enable GPIO19 as output */
+        orl	%d0,0x4(%a1)			/* de-assert IDE reset */
+.endm
+
+#define	PLATFORM_SETUP	m5249c3_setup
+
+#endif /* __ASSEMBLER__ */
+
+/****************************************************************************/
+#endif	/* m5249sim_h */