diff options
Diffstat (limited to 'drivers')
71 files changed, 584 insertions, 399 deletions
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c index 4b473948632..9033d164c4e 100644 --- a/drivers/ata/libata-sff.c +++ b/drivers/ata/libata-sff.c @@ -1227,10 +1227,19 @@ fsm_start: /* ATA PIO protocol */ if (unlikely((status & ATA_DRQ) == 0)) { /* handle BSY=0, DRQ=0 as error */ - if (likely(status & (ATA_ERR | ATA_DF))) + if (likely(status & (ATA_ERR | ATA_DF))) { /* device stops HSM for abort/error */ qc->err_mask |= AC_ERR_DEV; - else { + + /* If diagnostic failed and this is + * IDENTIFY, it's likely a phantom + * device. Mark hint. + */ + if (qc->dev->horkage & + ATA_HORKAGE_DIAGNOSTIC) + qc->err_mask |= + AC_ERR_NODEV_HINT; + } else { /* HSM violation. Let EH handle this. * Phantom devices also trigger this * condition. Mark hint. diff --git a/drivers/block/Kconfig b/drivers/block/Kconfig index 61ad8d639ba..0344a8a8321 100644 --- a/drivers/block/Kconfig +++ b/drivers/block/Kconfig @@ -21,7 +21,8 @@ config BLK_DEV_FD ---help--- If you want to use the floppy disk drive(s) of your PC under Linux, say Y. Information about this driver, especially important for IBM - Thinkpad users, is contained in <file:Documentation/floppy.txt>. + Thinkpad users, is contained in + <file:Documentation/blockdev/floppy.txt>. That file also contains the location of the Floppy driver FAQ as well as location of the fdutils package used to configure additional parameters of the driver at run time. @@ -76,7 +77,7 @@ config PARIDE your computer's parallel port. Most of them are actually IDE devices using a parallel port IDE adapter. This option enables the PARIDE subsystem which contains drivers for many of these external drives. - Read <file:Documentation/paride.txt> for more information. + Read <file:Documentation/blockdev/paride.txt> for more information. If you have said Y to the "Parallel-port support" configuration option, you may share a single port between your printer and other @@ -114,9 +115,9 @@ config BLK_CPQ_DA help This is the driver for Compaq Smart Array controllers. Everyone using these boards should say Y here. See the file - <file:Documentation/cpqarray.txt> for the current list of boards - supported by this driver, and for further information on the use of - this driver. + <file:Documentation/blockdev/cpqarray.txt> for the current list of + boards supported by this driver, and for further information on the + use of this driver. config BLK_CPQ_CISS_DA tristate "Compaq Smart Array 5xxx support" @@ -124,7 +125,7 @@ config BLK_CPQ_CISS_DA help This is the driver for Compaq Smart Array 5xxx controllers. Everyone using these boards should say Y here. - See <file:Documentation/cciss.txt> for the current list of + See <file:Documentation/blockdev/cciss.txt> for the current list of boards supported by this driver, and for further information on the use of this driver. @@ -135,7 +136,7 @@ config CISS_SCSI_TAPE help When enabled (Y), this option allows SCSI tape drives and SCSI medium changers (tape robots) to be accessed via a Compaq 5xxx array - controller. (See <file:Documentation/cciss.txt> for more details.) + controller. (See <file:Documentation/blockdev/cciss.txt> for more details.) "SCSI support" and "SCSI tape support" must also be enabled for this option to work. @@ -149,8 +150,8 @@ config BLK_DEV_DAC960 help This driver adds support for the Mylex DAC960, AcceleRAID, and eXtremeRAID PCI RAID controllers. See the file - <file:Documentation/README.DAC960> for further information about - this driver. + <file:Documentation/blockdev/README.DAC960> for further information + about this driver. To compile this driver as a module, choose M here: the module will be called DAC960. @@ -278,9 +279,9 @@ config BLK_DEV_NBD userland (making server and client physically the same computer, communicating using the loopback network device). - Read <file:Documentation/nbd.txt> for more information, especially - about where to find the server code, which runs in user space and - does not need special kernel support. + Read <file:Documentation/blockdev/nbd.txt> for more information, + especially about where to find the server code, which runs in user + space and does not need special kernel support. Note that this has nothing to do with the network file systems NFS or Coda; you can say N here even if you intend to use NFS or Coda. @@ -321,8 +322,8 @@ config BLK_DEV_RAM store a copy of a minimal root file system off of a floppy into RAM during the initial install of Linux. - Note that the kernel command line option "ramdisk=XX" is now - obsolete. For details, read <file:Documentation/ramdisk.txt>. + Note that the kernel command line option "ramdisk=XX" is now obsolete. + For details, read <file:Documentation/blockdev/ramdisk.txt>. To compile this driver as a module, choose M here: the module will be called rd. diff --git a/drivers/block/floppy.c b/drivers/block/floppy.c index 14db747a636..cf29cc4e6ab 100644 --- a/drivers/block/floppy.c +++ b/drivers/block/floppy.c @@ -4124,7 +4124,7 @@ static int __init floppy_setup(char *str) printk("\n"); } else DPRINT("botched floppy option\n"); - DPRINT("Read Documentation/floppy.txt\n"); + DPRINT("Read Documentation/blockdev/floppy.txt\n"); return 0; } diff --git a/drivers/block/ub.c b/drivers/block/ub.c index fccac18d311..048d71d244d 100644 --- a/drivers/block/ub.c +++ b/drivers/block/ub.c @@ -1546,8 +1546,6 @@ static void ub_top_sense_done(struct ub_dev *sc, struct ub_scsi_cmd *scmd) /* * Reset management - * XXX Move usb_reset_device to khubd. Hogging kevent is not a good thing. - * XXX Make usb_sync_reset asynchronous. */ static void ub_reset_enter(struct ub_dev *sc, int try) @@ -1633,6 +1631,22 @@ static void ub_reset_task(struct work_struct *work) } /* + * XXX Reset brackets are too much hassle to implement, so just stub them + * in order to prevent forced unbinding (which deadlocks solid when our + * ->disconnect method waits for the reset to complete and this kills keventd). + * + * XXX Tell Alan to move usb_unlock_device inside of usb_reset_device, + * or else the post_reset is invoked, and restats I/O on a locked device. + */ +static int ub_pre_reset(struct usb_interface *iface) { + return 0; +} + +static int ub_post_reset(struct usb_interface *iface) { + return 0; +} + +/* * This is called from a process context. */ static void ub_revalidate(struct ub_dev *sc, struct ub_lun *lun) @@ -2446,6 +2460,8 @@ static struct usb_driver ub_driver = { .probe = ub_probe, .disconnect = ub_disconnect, .id_table = ub_usb_ids, + .pre_reset = ub_pre_reset, + .post_reset = ub_post_reset, }; static int __init ub_init(void) diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig index 43b35d0369d..43d6ba83a19 100644 --- a/drivers/char/Kconfig +++ b/drivers/char/Kconfig @@ -124,7 +124,7 @@ config COMPUTONE which give you many serial ports. You would need something like this to connect more than two modems to your Linux box, for instance in order to become a dial-in server. If you have a card like that, say - Y here and read <file:Documentation/computone.txt>. + Y here and read <file:Documentation/serial/computone.txt>. To compile this driver as module, choose M here: the module will be called ip2. @@ -136,7 +136,7 @@ config ROCKETPORT This driver supports Comtrol RocketPort and RocketModem PCI boards. These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or modems. For information about the RocketPort/RocketModem boards - and this driver read <file:Documentation/rocket.txt>. + and this driver read <file:Documentation/serial/rocket.txt>. To compile this driver as a module, choose M here: the module will be called rocket. @@ -154,7 +154,7 @@ config CYCLADES your Linux box, for instance in order to become a dial-in server. For information about the Cyclades-Z card, read - <file:Documentation/README.cycladesZ>. + <file:Documentation/serial/README.cycladesZ>. To compile this driver as a module, choose M here: the module will be called cyclades. @@ -183,7 +183,7 @@ config DIGIEPCA box, for instance in order to become a dial-in server. This driver supports the original PC (ISA) boards as well as PCI, and EISA. If you have a card like this, say Y here and read the file - <file:Documentation/digiepca.txt>. + <file:Documentation/serial/digiepca.txt>. To compile this driver as a module, choose M here: the module will be called epca. @@ -289,7 +289,7 @@ config RISCOM8 which gives you many serial ports. You would need something like this to connect more than two modems to your Linux box, for instance in order to become a dial-in server. If you have a card like that, - say Y here and read the file <file:Documentation/riscom8.txt>. + say Y here and read the file <file:Documentation/serial/riscom8.txt>. Also it's possible to say M here and compile this driver as kernel loadable module; the module will be called riscom8. @@ -304,8 +304,8 @@ config SPECIALIX your Linux box, for instance in order to become a dial-in server. If you have a card like that, say Y here and read the file - <file:Documentation/specialix.txt>. Also it's possible to say M here - and compile this driver as kernel loadable module which will be + <file:Documentation/serial/specialix.txt>. Also it's possible to say + M here and compile this driver as kernel loadable module which will be called specialix. config SX @@ -313,7 +313,7 @@ config SX depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA) help This is a driver for the SX and SI multiport serial cards. - Please read the file <file:Documentation/sx.txt> for details. + Please read the file <file:Documentation/serial/sx.txt> for details. This driver can only be built as a module ( = code which can be inserted in and removed from the running kernel whenever you want). @@ -344,8 +344,8 @@ config STALDRV like this to connect more than two modems to your Linux box, for instance in order to become a dial-in server. If you say Y here, you will be asked for your specific card model in the next - questions. Make sure to read <file:Documentation/stallion.txt> in - this case. If you have never heard about all this, it's safe to + questions. Make sure to read <file:Documentation/serial/stallion.txt> + in this case. If you have never heard about all this, it's safe to say N. config STALLION @@ -354,7 +354,7 @@ config STALLION help If you have an EasyIO or EasyConnection 8/32 multiport Stallion card, then this is for you; say Y. Make sure to read - <file:Documentation/stallion.txt>. + <file:Documentation/serial/stallion.txt>. To compile this driver as a module, choose M here: the module will be called stallion. @@ -365,7 +365,7 @@ config ISTALLION help If you have an EasyConnection 8/64, ONboard, Brumby or Stallion serial multiport card, say Y here. Make sure to read - <file:Documentation/stallion.txt>. + <file:Documentation/serial/stallion.txt>. To compile this driver as a module, choose M here: the module will be called istallion. diff --git a/drivers/char/specialix.c b/drivers/char/specialix.c index 242fd46fda2..a16b94f12eb 100644 --- a/drivers/char/specialix.c +++ b/drivers/char/specialix.c @@ -72,7 +72,7 @@ /* * There is a bunch of documentation about the card, jumpers, config * settings, restrictions, cables, device names and numbers in - * Documentation/specialix.txt + * Documentation/serial/specialix.txt */ #include <linux/module.h> diff --git a/drivers/hwmon/lis3lv02d.c b/drivers/hwmon/lis3lv02d.c index 752b5c44df9..c002144c76b 100644 --- a/drivers/hwmon/lis3lv02d.c +++ b/drivers/hwmon/lis3lv02d.c @@ -33,7 +33,6 @@ #include <linux/wait.h> #include <linux/poll.h> #include <linux/freezer.h> -#include <linux/version.h> #include <linux/uaccess.h> #include <acpi/acpi_drivers.h> #include <asm/atomic.h> diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c index 640cbb23732..3384a717fec 100644 --- a/drivers/i2c/busses/i2c-sh_mobile.c +++ b/drivers/i2c/busses/i2c-sh_mobile.c @@ -318,7 +318,8 @@ static int sh_mobile_i2c_isr_rx(struct sh_mobile_i2c_data *pd) } else data = i2c_op(pd, OP_RX, 0); - pd->msg->buf[real_pos] = data; + if (real_pos >= 0) + pd->msg->buf[real_pos] = data; } while (0); pd->pos++; diff --git a/drivers/ide/ide-cs.c b/drivers/ide/ide-cs.c index cb199c815b5..f50210fe558 100644 --- a/drivers/ide/ide-cs.c +++ b/drivers/ide/ide-cs.c @@ -444,6 +444,7 @@ static struct pcmcia_device_id ide_ids[] = { PCMCIA_DEVICE_PROD_ID1("STI Flash", 0xe4a13209), PCMCIA_DEVICE_PROD_ID12("STI", "Flash 5.0", 0xbf2df18d, 0x8cb57a0e), PCMCIA_MFC_DEVICE_PROD_ID12(1, "SanDisk", "ConnectPlus", 0x7a954bd9, 0x74be00c6), + PCMCIA_DEVICE_PROD_ID2("Flash Card", 0x5a362506), PCMCIA_DEVICE_NULL, }; MODULE_DEVICE_TABLE(pcmcia, ide_ids); diff --git a/drivers/md/dm-mpath.c b/drivers/md/dm-mpath.c index 4840733cd90..3d7f4923cd1 100644 --- a/drivers/md/dm-mpath.c +++ b/drivers/md/dm-mpath.c @@ -441,13 +441,13 @@ static void process_queued_ios(struct work_struct *work) __choose_pgpath(m); pgpath = m->current_pgpath; - m->pgpath_to_activate = m->current_pgpath; if ((pgpath && !m->queue_io) || (!pgpath && !m->queue_if_no_path)) must_queue = 0; - if (m->pg_init_required && !m->pg_init_in_progress) { + if (m->pg_init_required && !m->pg_init_in_progress && pgpath) { + m->pgpath_to_activate = pgpath; m->pg_init_count++; m->pg_init_required = 0; m->pg_init_in_progress = 1; @@ -708,6 +708,10 @@ static int parse_hw_handler(struct arg_set *as, struct multipath *m) m->hw_handler_name = NULL; return -EINVAL; } + + if (hw_argc > 1) + DMWARN("Ignoring user-specified arguments for " + "hardware handler \"%s\"", m->hw_handler_name); consume(as, hw_argc - 1); return 0; diff --git a/drivers/md/dm-raid1.c b/drivers/md/dm-raid1.c index 9d7b53ed75b..ec43f9fa4b2 100644 --- a/drivers/md/dm-raid1.c +++ b/drivers/md/dm-raid1.c @@ -1032,6 +1032,7 @@ static void mirror_dtr(struct dm_target *ti) del_timer_sync(&ms->timer); flush_workqueue(ms->kmirrord_wq); + flush_scheduled_work(); dm_kcopyd_client_destroy(ms->kcopyd_client); destroy_workqueue(ms->kmirrord_wq); free_context(ms, ti, ms->nr_mirrors); diff --git a/drivers/md/dm-stripe.c b/drivers/md/dm-stripe.c index a2d068dbe9e..9e4ef88d421 100644 --- a/drivers/md/dm-stripe.c +++ b/drivers/md/dm-stripe.c @@ -320,8 +320,10 @@ int __init dm_stripe_init(void) int r; r = dm_register_target(&stripe_target); - if (r < 0) + if (r < 0) { DMWARN("target registration failed"); + return r; + } kstriped = create_singlethread_workqueue("kstriped"); if (!kstriped) { diff --git a/drivers/md/dm.c b/drivers/md/dm.c index 6963ad14840..c99e4728ff4 100644 --- a/drivers/md/dm.c +++ b/drivers/md/dm.c @@ -375,7 +375,7 @@ static void start_io_acct(struct dm_io *io) dm_disk(md)->part0.in_flight = atomic_inc_return(&md->pending); } -static int end_io_acct(struct dm_io *io) +static void end_io_acct(struct dm_io *io) { struct mapped_device *md = io->md; struct bio *bio = io->bio; @@ -391,7 +391,9 @@ static int end_io_acct(struct dm_io *io) dm_disk(md)->part0.in_flight = pending = at |