diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/hwmon/Kconfig | 92 | ||||
| -rw-r--r-- | drivers/hwmon/Makefile | 10 | ||||
| -rw-r--r-- | drivers/hwmon/f71882fg.c | 522 | ||||
| -rw-r--r-- | drivers/hwmon/lineage-pem.c | 586 | ||||
| -rw-r--r-- | drivers/hwmon/lis3lv02d_spi.c | 19 | ||||
| -rw-r--r-- | drivers/hwmon/lm85.c | 136 | ||||
| -rw-r--r-- | drivers/hwmon/ltc4151.c | 256 | ||||
| -rw-r--r-- | drivers/hwmon/max16064.c | 91 | ||||
| -rw-r--r-- | drivers/hwmon/max34440.c | 199 | ||||
| -rw-r--r-- | drivers/hwmon/max6639.c | 653 | ||||
| -rw-r--r-- | drivers/hwmon/max8688.c | 158 | ||||
| -rw-r--r-- | drivers/hwmon/pmbus.c | 203 | ||||
| -rw-r--r-- | drivers/hwmon/pmbus.h | 313 | ||||
| -rw-r--r-- | drivers/hwmon/pmbus_core.c | 1658 | ||||
| -rw-r--r-- | drivers/hwmon/w83627ehf.c | 1351 |
15 files changed, 5683 insertions, 564 deletions
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 297bc9a7d6e..1bfb4439e4e 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -467,6 +467,17 @@ config SENSORS_JC42 This driver can also be built as a module. If so, the module will be called jc42. +config SENSORS_LINEAGE + tristate "Lineage Compact Power Line Power Entry Module" + depends on I2C && EXPERIMENTAL + help + If you say yes here you get support for the Lineage Compact Power Line + series of DC/DC and AC/DC converters such as CP1800, CP2000AC, + CP2000DC, CP2725, and others. + + This driver can also be built as a module. If so, the module + will be called lineage-pem. + config SENSORS_LM63 tristate "National Semiconductor LM63 and LM64" depends on I2C @@ -625,6 +636,17 @@ config SENSORS_LM93 This driver can also be built as a module. If so, the module will be called lm93. +config SENSORS_LTC4151 + tristate "Linear Technology LTC4151" + depends on I2C + default n + help + If you say yes here you get support for Linear Technology LTC4151 + High Voltage I2C Current and Voltage Monitor interface. + + This driver can also be built as a module. If so, the module will + be called ltc4151. + config SENSORS_LTC4215 tristate "Linear Technology LTC4215" depends on I2C && EXPERIMENTAL @@ -685,6 +707,16 @@ config SENSORS_MAX1619 This driver can also be built as a module. If so, the module will be called max1619. +config SENSORS_MAX6639 + tristate "Maxim MAX6639 sensor chip" + depends on I2C && EXPERIMENTAL + help + If you say yes here you get support for the MAX6639 + sensor chips. + + This driver can also be built as a module. If so, the module + will be called max6639. + config SENSORS_MAX6650 tristate "Maxim MAX6650 sensor chip" depends on I2C && EXPERIMENTAL @@ -735,6 +767,61 @@ config SENSORS_PCF8591 These devices are hard to detect and rarely found on mainstream hardware. If unsure, say N. +config PMBUS + tristate "PMBus support" + depends on I2C && EXPERIMENTAL + default n + help + Say yes here if you want to enable PMBus support. + + This driver can also be built as a module. If so, the module will + be called pmbus_core. + +if PMBUS + +config SENSORS_PMBUS + tristate "Generic PMBus devices" + default n + help + If you say yes here you get hardware monitoring support for generic + PMBus devices, including but not limited to BMR450, BMR451, BMR453, + BMR454, and LTC2978. + + This driver can also be built as a module. If so, the module will + be called pmbus. + +config SENSORS_MAX16064 + tristate "Maxim MAX16064" + default n + help + If you say yes here you get hardware monitoring support for Maxim + MAX16064. + + This driver can also be built as a module. If so, the module will + be called max16064. + +config SENSORS_MAX34440 + tristate "Maxim MAX34440/MAX34441" + default n + help + If you say yes here you get hardware monitoring support for Maxim + MAX34440 and MAX34441. + + This driver can also be built as a module. If so, the module will + be called max34440. + +config SENSORS_MAX8688 + tristate "Maxim MAX8688" + default n + help + If you say yes here you get hardware monitoring support for Maxim + MAX8688. + + This driver can also be built as a module. If so, the module will + be called max8688. + +endif # PMBUS + config SENSORS_SHT15 tristate "Sensiron humidity and temperature sensors. SHT15 and compat." depends on GENERIC_GPIO @@ -1083,7 +1170,7 @@ config SENSORS_W83627HF will be called w83627hf. config SENSORS_W83627EHF - tristate "Winbond W83627EHF/EHG/DHG, W83667HG" + tristate "Winbond W83627EHF/EHG/DHG, W83667HG, NCT6775F, NCT6776F" select HWMON_VID help If you say yes here you get support for the hardware @@ -1094,7 +1181,8 @@ config SENSORS_W83627EHF chip suited for specific Intel processors that use PECI such as the Core 2 Duo. - This driver also supports the W83667HG chip. + This driver also supports Nuvoton W83667HG, W83667HG-B, NCT6775F + (also known as W83667HG-I), and NCT6776F. This driver can also be built as a module. If so, the module will be called w83627ehf. diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index dde02d99c23..bd0410e4b44 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -62,6 +62,7 @@ obj-$(CONFIG_SENSORS_JC42) += jc42.o obj-$(CONFIG_SENSORS_JZ4740) += jz4740-hwmon.o obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.o obj-$(CONFIG_SENSORS_K10TEMP) += k10temp.o +obj-$(CONFIG_SENSORS_LINEAGE) += lineage-pem.o obj-$(CONFIG_SENSORS_LIS3LV02D) += lis3lv02d.o hp_accel.o obj-$(CONFIG_SENSORS_LIS3_SPI) += lis3lv02d.o lis3lv02d_spi.o obj-$(CONFIG_SENSORS_LIS3_I2C) += lis3lv02d.o lis3lv02d_i2c.o @@ -79,11 +80,13 @@ obj-$(CONFIG_SENSORS_LM90) += lm90.o obj-$(CONFIG_SENSORS_LM92) += lm92.o obj-$(CONFIG_SENSORS_LM93) += lm93.o obj-$(CONFIG_SENSORS_LM95241) += lm95241.o +obj-$(CONFIG_SENSORS_LTC4151) += ltc4151.o obj-$(CONFIG_SENSORS_LTC4215) += ltc4215.o obj-$(CONFIG_SENSORS_LTC4245) += ltc4245.o obj-$(CONFIG_SENSORS_LTC4261) += ltc4261.o obj-$(CONFIG_SENSORS_MAX1111) += max1111.o obj-$(CONFIG_SENSORS_MAX1619) += max1619.o +obj-$(CONFIG_SENSORS_MAX6639) += max6639.o obj-$(CONFIG_SENSORS_MAX6650) += max6650.o obj-$(CONFIG_SENSORS_MC13783_ADC)+= mc13783-adc.o obj-$(CONFIG_SENSORS_PC87360) += pc87360.o @@ -112,6 +115,13 @@ obj-$(CONFIG_SENSORS_W83L786NG) += w83l786ng.o obj-$(CONFIG_SENSORS_WM831X) += wm831x-hwmon.o obj-$(CONFIG_SENSORS_WM8350) += wm8350-hwmon.o +# PMBus drivers +obj-$(CONFIG_PMBUS) += pmbus_core.o +obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o +obj-$(CONFIG_SENSORS_MAX16064) += max16064.o +obj-$(CONFIG_SENSORS_MAX34440) += max34440.o +obj-$(CONFIG_SENSORS_MAX8688) += max8688.o + ifeq ($(CONFIG_HWMON_DEBUG_CHIP),y) EXTRA_CFLAGS += -DDEBUG endif diff --git a/drivers/hwmon/f71882fg.c b/drivers/hwmon/f71882fg.c index 6e06019015a..a4d430ee7e2 100644 --- a/drivers/hwmon/f71882fg.c +++ b/drivers/hwmon/f71882fg.c @@ -1,6 +1,6 @@ /*************************************************************************** * Copyright (C) 2006 by Hans Edgington <hans@edgington.nl> * - * Copyright (C) 2007-2009 Hans de Goede <hdegoede@redhat.com> * + * Copyright (C) 2007-2011 Hans de Goede <hdegoede@redhat.com> * * * * This program is free software; you can redistribute it and/or modify * * it under the terms of the GNU General Public License as published by * @@ -47,22 +47,23 @@ #define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */ #define SIO_FINTEK_ID 0x1934 /* Manufacturers ID */ +#define SIO_F71808E_ID 0x0901 /* Chipset ID */ #define SIO_F71858_ID 0x0507 /* Chipset ID */ #define SIO_F71862_ID 0x0601 /* Chipset ID */ +#define SIO_F71869_ID 0x0814 /* Chipset ID */ #define SIO_F71882_ID 0x0541 /* Chipset ID */ #define SIO_F71889_ID 0x0723 /* Chipset ID */ +#define SIO_F71889E_ID 0x0909 /* Chipset ID */ #define SIO_F8000_ID 0x0581 /* Chipset ID */ #define REGION_LENGTH 8 #define ADDR_REG_OFFSET 5 #define DATA_REG_OFFSET 6 -#define F71882FG_REG_PECI 0x0A - -#define F71882FG_REG_IN_STATUS 0x12 /* f71882fg only */ -#define F71882FG_REG_IN_BEEP 0x13 /* f71882fg only */ +#define F71882FG_REG_IN_STATUS 0x12 /* f7188x only */ +#define F71882FG_REG_IN_BEEP 0x13 /* f7188x only */ #define F71882FG_REG_IN(nr) (0x20 + (nr)) -#define F71882FG_REG_IN1_HIGH 0x32 /* f71882fg only */ +#define F71882FG_REG_IN1_HIGH 0x32 /* f7188x only */ #define F71882FG_REG_FAN(nr) (0xA0 + (16 * (nr))) #define F71882FG_REG_FAN_TARGET(nr) (0xA2 + (16 * (nr))) @@ -86,28 +87,71 @@ #define F71882FG_REG_FAN_HYST(nr) (0x98 + (nr)) +#define F71882FG_REG_FAN_FAULT_T 0x9F +#define F71882FG_FAN_NEG_TEMP_EN 0x20 +#define F71882FG_FAN_PROG_SEL 0x80 + #define F71882FG_REG_POINT_PWM(pwm, point) (0xAA + (point) + (16 * (pwm))) #define F71882FG_REG_POINT_TEMP(pwm, point) (0xA6 + (point) + (16 * (pwm))) #define F71882FG_REG_POINT_MAPPING(nr) (0xAF + 16 * (nr)) #define F71882FG_REG_START 0x01 +#define F71882FG_MAX_INS 9 + #define FAN_MIN_DETECT 366 /* Lowest detectable fanspeed */ static unsigned short force_id; module_param(force_id, ushort, 0); MODULE_PARM_DESC(force_id, "Override the detected device ID"); -enum chips { f71858fg, f71862fg, f71882fg, f71889fg, f8000 }; +enum chips { f71808e, f71858fg, f71862fg, f71869, f71882fg, f71889fg, + f71889ed, f8000 }; static const char *f71882fg_names[] = { + "f71808e", "f71858fg", "f71862fg", + "f71869", /* Both f71869f and f71869e, reg. compatible and same id */ "f71882fg", "f71889fg", + "f71889ed", "f8000", }; +static const char f71882fg_has_in[8][F71882FG_MAX_INS] = { + { 1, 1, 1, 1, 1, 1, 0, 1, 1 }, /* f71808e */ + { 1, 1, 1, 0, 0, 0, 0, 0, 0 }, /* f71858fg */ + { 1, 1, 1, 1, 1, 1, 1, 1, 1 }, /* f71862fg */ + { 1, 1, 1, 1, 1, 1, 1, 1, 1 }, /* f71869 */ + { 1, 1, 1, 1, 1, 1, 1, 1, 1 }, /* f71882fg */ + { 1, 1, 1, 1, 1, 1, 1, 1, 1 }, /* f71889fg */ + { 1, 1, 1, 1, 1, 1, 1, 1, 1 }, /* f71889ed */ + { 1, 1, 1, 0, 0, 0, 0, 0, 0 }, /* f8000 */ +}; + +static const char f71882fg_has_in1_alarm[8] = { + 0, /* f71808e */ + 0, /* f71858fg */ + 0, /* f71862fg */ + 0, /* f71869 */ + 1, /* f71882fg */ + 1, /* f71889fg */ + 1, /* f71889ed */ + 0, /* f8000 */ +}; + +static const char f71882fg_has_beep[8] = { + 0, /* f71808e */ + 0, /* f71858fg */ + 1, /* f71862fg */ + 1, /* f71869 */ + 1, /* f71882fg */ + 1, /* f71889fg */ + 1, /* f71889ed */ + 0, /* f8000 */ +}; + static struct platform_device *f71882fg_pdev; /* Super-I/O Function prototypes */ @@ -129,11 +173,12 @@ struct f71882fg_data { struct mutex update_lock; int temp_start; /* temp numbering start (0 or 1) */ char valid; /* !=0 if following fields are valid */ + char auto_point_temp_signed; unsigned long last_updated; /* In jiffies */ unsigned long last_limits; /* In jiffies */ /* Register Values */ - u8 in[9]; + u8 in[F71882FG_MAX_INS]; u8 in1_max; u8 in_status; u8 in_beep; @@ -142,7 +187,7 @@ struct f71882fg_data { u16 fan_full_speed[4]; u8 fan_status; u8 fan_beep; - /* Note: all models have only 3 temperature channels, but on some + /* Note: all models have max 3 temperature channels, but on some they are addressed as 0-2 and on others as 1-3, so for coding convenience we reserve space for 4 channels */ u16 temp[4]; @@ -262,13 +307,9 @@ static struct platform_driver f71882fg_driver = { static DEVICE_ATTR(name, S_IRUGO, show_name, NULL); -/* Temp and in attr for the f71858fg, the f71858fg is special as it - has its temperature indexes start at 0 (the others start at 1) and - it only has 3 voltage inputs */ -static struct sensor_device_attribute_2 f71858fg_in_temp_attr[] = { - SENSOR_ATTR_2(in0_input, S_IRUGO, show_in, NULL, 0, 0), - SENSOR_ATTR_2(in1_input, S_IRUGO, show_in, NULL, 0, 1), - SENSOR_ATTR_2(in2_input, S_IRUGO, show_in, NULL, 0, 2), +/* Temp attr for the f71858fg, the f71858fg is special as it has its + temperature indexes start at 0 (the others start at 1) */ +static struct sensor_device_attribute_2 f71858fg_temp_attr[] = { SENSOR_ATTR_2(temp1_input, S_IRUGO, show_temp, NULL, 0, 0), SENSOR_ATTR_2(temp1_max, S_IRUGO|S_IWUSR, show_temp_max, store_temp_max, 0, 0), @@ -292,7 +333,6 @@ static struct sensor_device_attribute_2 f71858fg_in_temp_attr[] = { SENSOR_ATTR_2(temp2_crit_hyst, S_IRUGO, show_temp_crit_hyst, NULL, 0, 1), SENSOR_ATTR_2(temp2_crit_alarm, S_IRUGO, show_temp_alarm, NULL, 0, 5), - SENSOR_ATTR_2(temp2_type, S_IRUGO, show_temp_type, NULL, 0, 1), SENSOR_ATTR_2(temp2_fault, S_IRUGO, show_temp_fault, NULL, 0, 1), SENSOR_ATTR_2(temp3_input, S_IRUGO, show_temp, NULL, 0, 2), SENSOR_ATTR_2(temp3_max, S_IRUGO|S_IWUSR, show_temp_max, @@ -308,17 +348,8 @@ static struct sensor_device_attribute_2 f71858fg_in_temp_attr[] = { SENSOR_ATTR_2(temp3_fault, S_IRUGO, show_temp_fault, NULL, 0, 2), }; -/* Temp and in attr common to the f71862fg, f71882fg and f71889fg */ -static struct sensor_device_attribute_2 fxxxx_in_temp_attr[] = { - SENSOR_ATTR_2(in0_input, S_IRUGO, show_in, NULL, 0, 0), - SENSOR_ATTR_2(in1_input, S_IRUGO, show_in, NULL, 0, 1), - SENSOR_ATTR_2(in2_input, S_IRUGO, show_in, NULL, 0, 2), - SENSOR_ATTR_2(in3_input, S_IRUGO, show_in, NULL, 0, 3), - SENSOR_ATTR_2(in4_input, S_IRUGO, show_in, NULL, 0, 4), - SENSOR_ATTR_2(in5_input, S_IRUGO, show_in, NULL, 0, 5), - SENSOR_ATTR_2(in6_input, S_IRUGO, show_in, NULL, 0, 6), - SENSOR_ATTR_2(in7_input, S_IRUGO, show_in, NULL, 0, 7), - SENSOR_ATTR_2(in8_input, S_IRUGO, show_in, NULL, 0, 8), +/* Temp attr for the standard models */ +static struct sensor_device_attribute_2 fxxxx_temp_attr[3][9] = { { SENSOR_ATTR_2(temp1_input, S_IRUGO, show_temp, NULL, 0, 1), SENSOR_ATTR_2(temp1_max, S_IRUGO|S_IWUSR, show_temp_max, store_temp_max, 0, 1), @@ -328,17 +359,14 @@ static struct sensor_device_attribute_2 fxxxx_in_temp_attr[] = { the max and crit alarms separately and lm_sensors v2 depends on the presence of temp#_alarm files. The same goes for temp2/3 _alarm. */ SENSOR_ATTR_2(temp1_alarm, S_IRUGO, show_temp_alarm, NULL, 0, 1), - SENSOR_ATTR_2(temp1_max_beep, S_IRUGO|S_IWUSR, show_temp_beep, - store_temp_beep, 0, 1), SENSOR_ATTR_2(temp1_crit, S_IRUGO|S_IWUSR, show_temp_crit, store_temp_crit, 0, 1), SENSOR_ATTR_2(temp1_crit_hyst, S_IRUGO, show_temp_crit_hyst, NULL, 0, 1), SENSOR_ATTR_2(temp1_crit_alarm, S_IRUGO, show_temp_alarm, NULL, 0, 5), - SENSOR_ATTR_2(temp1_crit_beep, S_IRUGO|S_IWUSR, show_temp_beep, - store_temp_beep, 0, 5), SENSOR_ATTR_2(temp1_type, S_IRUGO, show_temp_type, NULL, 0, 1), SENSOR_ATTR_2(temp1_fault, S_IRUGO, show_temp_fault, NULL, 0, 1), +}, { SENSOR_ATTR_2(temp2_input, S_IRUGO, show_temp, NULL, 0, 2), SENSOR_ATTR_2(temp2_max, S_IRUGO|S_IWUSR, show_temp_max, store_temp_max, 0, 2), @@ -346,17 +374,14 @@ static struct sensor_device_attribute_2 fxxxx_in_temp_attr[] = { store_temp_max_hyst, 0, 2), /* Should be temp2_max_alarm, see temp1_alarm note */ SENSOR_ATTR_2(temp2_alarm, S_IRUGO, show_temp_alarm, NULL, 0, 2), - SENSOR_ATTR_2(temp2_max_beep, S_IRUGO|S_IWUSR, show_temp_beep, - store_temp_beep, 0, 2), SENSOR_ATTR_2(temp2_crit, S_IRUGO|S_IWUSR, show_temp_crit, store_temp_crit, 0, 2), SENSOR_ATTR_2(temp2_crit_hyst, S_IRUGO, show_temp_crit_hyst, NULL, 0, 2), SENSOR_ATTR_2(temp2_crit_alarm, S_IRUGO, show_temp_alarm, NULL, 0, 6), - SENSOR_ATTR_2(temp2_crit_beep, S_IRUGO|S_IWUSR, show_temp_beep, - store_temp_beep, 0, 6), SENSOR_ATTR_2(temp2_type, S_IRUGO, show_temp_type, NULL, 0, 2), SENSOR_ATTR_2(temp2_fault, S_IRUGO, show_temp_fault, NULL, 0, 2), +}, { SENSOR_ATTR_2(temp3_input, S_IRUGO, show_temp, NULL, 0, 3), SENSOR_ATTR_2(temp3_max, S_IRUGO|S_IWUSR, show_temp_max, store_temp_max, 0, 3), @@ -364,37 +389,39 @@ static struct sensor_device_attribute_2 fxxxx_in_temp_attr[] = { store_temp_max_hyst, 0, 3), /* Should be temp3_max_alarm, see temp1_alarm note */ SENSOR_ATTR_2(temp3_alarm, S_IRUGO, show_temp_alarm, NULL, 0, 3), - SENSOR_ATTR_2(temp3_max_beep, S_IRUGO|S_IWUSR, show_temp_beep, - store_temp_beep, 0, 3), SENSOR_ATTR_2(temp3_crit, S_IRUGO|S_IWUSR, show_temp_crit, store_temp_crit, 0, 3), SENSOR_ATTR_2(temp3_crit_hyst, S_IRUGO, show_temp_crit_hyst, NULL, 0, 3), SENSOR_ATTR_2(temp3_crit_alarm, S_IRUGO, show_temp_alarm, NULL, 0, 7), - SENSOR_ATTR_2(temp3_crit_beep, S_IRUGO|S_IWUSR, show_temp_beep, - store_temp_beep, 0, 7), SENSOR_ATTR_2(temp3_type, S_IRUGO, show_temp_type, NULL, 0, 3), SENSOR_ATTR_2(temp3_fault, S_IRUGO, show_temp_fault, NULL, 0, 3), -}; +} }; -/* For models with in1 alarm capability */ -static struct sensor_device_attribute_2 fxxxx_in1_alarm_attr[] = { - SENSOR_ATTR_2(in1_max, S_IRUGO|S_IWUSR, show_in_max, store_in_max, - 0, 1), - SENSOR_ATTR_2(in1_beep, S_IRUGO|S_IWUSR, show_in_beep, store_in_beep, - 0, 1), - SENSOR_ATTR_2(in1_alarm, S_IRUGO, show_in_alarm, NULL, 0, 1), -}; +/* Temp attr for models which can beep on temp alarm */ +static struct sensor_device_attribute_2 fxxxx_temp_beep_attr[3][2] = { { + SENSOR_ATTR_2(temp1_max_beep, S_IRUGO|S_IWUSR, show_temp_beep, + store_temp_beep, 0, 1), + SENSOR_ATTR_2(temp1_crit_beep, S_IRUGO|S_IWUSR, show_temp_beep, + store_temp_beep, 0, 5), +}, { + SENSOR_ATTR_2(temp2_max_beep, S_IRUGO|S_IWUSR, show_temp_beep, + store_temp_beep, 0, 2), + SENSOR_ATTR_2(temp2_crit_beep, S_IRUGO|S_IWUSR, show_temp_beep, + store_temp_beep, 0, 6), +}, { + SENSOR_ATTR_2(temp3_max_beep, S_IRUGO|S_IWUSR, show_temp_beep, + store_temp_beep, 0, 3), + SENSOR_ATTR_2(temp3_crit_beep, S_IRUGO|S_IWUSR, show_temp_beep, + store_temp_beep, 0, 7), +} }; -/* Temp and in attr for the f8000 +/* Temp attr for the f8000 Note on the f8000 temp_ovt (crit) is used as max, and temp_high (max) is used as hysteresis value to clear alarms Also like the f71858fg its temperature indexes start at 0 */ -static struct sensor_device_attribute_2 f8000_in_temp_attr[] = { - SENSOR_ATTR_2(in0_input, S_IRUGO, show_in, NULL, 0, 0), - SENSOR_ATTR_2(in1_input, S_IRUGO, show_in, NULL, 0, 1), - SENSOR_ATTR_2(in2_input, S_IRUGO, show_in, NULL, 0, 2), +static struct sensor_device_attribute_2 f8000_temp_attr[] = { SENSOR_ATTR_2(temp1_input, S_IRUGO, show_temp, NULL, 0, 0), SENSOR_ATTR_2(temp1_max, S_IRUGO|S_IWUSR, show_temp_crit, store_temp_crit, 0, 0), @@ -408,7 +435,6 @@ static struct sensor_device_attribute_2 f8000_in_temp_attr[] = { SENSOR_ATTR_2(temp2_max_hyst, S_IRUGO|S_IWUSR, show_temp_max, store_temp_max, 0, 1), SENSOR_ATTR_2(temp2_alarm, S_IRUGO, show_temp_alarm, NULL, 0, 5), - SENSOR_ATTR_2(temp2_type, S_IRUGO, show_temp_type, NULL, 0, 1), SENSOR_ATTR_2(temp2_fault, S_IRUGO, show_temp_fault, NULL, 0, 1), SENSOR_ATTR_2(temp3_input, S_IRUGO, show_temp, NULL, 0, 2), SENSOR_ATTR_2(temp3_max, S_IRUGO|S_IWUSR, show_temp_crit, @@ -419,6 +445,28 @@ static struct sensor_device_attribute_2 f8000_in_temp_attr[] = { SENSOR_ATTR_2(temp3_fault, S_IRUGO, show_temp_fault, NULL, 0, 2), }; +/* in attr for all models */ +static struct sensor_device_attribute_2 fxxxx_in_attr[] = { + SENSOR_ATTR_2(in0_input, S_IRUGO, show_in, NULL, 0, 0), + SENSOR_ATTR_2(in1_input, S_IRUGO, show_in, NULL, 0, 1), + SENSOR_ATTR_2(in2_input, S_IRUGO, show_in, NULL, 0, 2), + SENSOR_ATTR_2(in3_input, S_IRUGO, show_in, NULL, 0, 3), + SENSOR_ATTR_2(in4_input, S_IRUGO, show_in, NULL, 0, 4), + SENSOR_ATTR_2(in5_input, S_IRUGO, show_in, NULL, 0, 5), + SENSOR_ATTR_2(in6_input, S_IRUGO, show_in, NULL, 0, 6), + SENSOR_ATTR_2(in7_input, S_IRUGO, show_in, NULL, 0, 7), + SENSOR_ATTR_2(in8_input, S_IRUGO, show_in, NULL, 0, 8), +}; + +/* For models with in1 alarm capability */ +static struct sensor_device_attribute_2 fxxxx_in1_alarm_attr[] = { + SENSOR_ATTR_2(in1_max, S_IRUGO|S_IWUSR, show_in_max, store_in_max, + 0, 1), + SENSOR_ATTR_2(in1_beep, S_IRUGO|S_IWUSR, show_in_beep, store_in_beep, + 0, 1), + SENSOR_ATTR_2(in1_alarm, S_IRUGO, show_in_alarm, NULL, 0, 1), +}; + /* Fan / PWM attr common to all models */ static struct sensor_device_attribute_2 fxxxx_fan_attr[4][6] = { { SENSOR_ATTR_2(fan1_input, S_IRUGO, show_fan, NULL, 0, 0), @@ -479,7 +527,7 @@ static struct sensor_device_attribute_2 fxxxx_fan_beep_attr[] = { }; /* PWM attr for the f71862fg, fewer pwms and fewer zones per pwm than the - f71858fg / f71882fg / f71889fg */ + standard models */ static struct sensor_device_attribute_2 f71862fg_auto_pwm_attr[] = { SENSOR_ATTR_2(pwm1_auto_channels_temp, S_IRUGO|S_IWUSR, show_pwm_auto_point_channel, @@ -548,7 +596,87 @@ static struct sensor_device_attribute_2 f71862fg_auto_pwm_attr[] = { show_pwm_auto_point_temp_hyst, NULL, 3, 2), }; -/* PWM attr common to the f71858fg, f71882fg and f71889fg */ +/* PWM attr for the f71808e/f71869, almost identical to the f71862fg, but the + pwm setting when the temperature is above the pwmX_auto_point1_temp can be + programmed instead of being hardcoded to 0xff */ +static struct sensor_device_attribute_2 f71869_auto_pwm_attr[] = { + SENSOR_ATTR_2(pwm1_auto_channels_temp, S_IRUGO|S_IWUSR, + show_pwm_auto_point_channel, + store_pwm_auto_point_channel, 0, 0), + SENSOR_ATTR_2(pwm1_auto_point1_pwm, S_IRUGO|S_IWUSR, + show_pwm_auto_point_pwm, store_pwm_auto_point_pwm, + 0, 0), + SENSOR_ATTR_2(pwm1_auto_point2_pwm, S_IRUGO|S_IWUSR, + show_pwm_auto_point_pwm, store_pwm_auto_point_pwm, + 1, 0), + SENSOR_ATTR_2(pwm1_auto_point3_pwm, S_IRUGO|S_IWUSR, + show_pwm_auto_point_pwm, store_pwm_auto_point_pwm, + 4, 0), + SENSOR_ATTR_2(pwm1_auto_point1_temp, S_IRUGO|S_IWUSR, + show_pwm_auto_point_temp, store_pwm_auto_point_temp, + 0, 0), + SENSOR_ATTR_2(pwm1_auto_point2_temp, S_IRUGO|S_IWUSR, + show_pwm_auto_point_temp, store_pwm_auto_point_temp, + 3, 0), + SENSOR_ATTR_2(pwm1_auto_point1_temp_hyst, S_IRUGO|S_IWUSR, + show_pwm_auto_point_temp_hyst, + store_pwm_auto_point_temp_hyst, + 0, 0), + SENSOR_ATTR_2(pwm1_auto_point2_temp_hyst, S_IRUGO, + show_pwm_auto_point_temp_hyst, NULL, 3, 0), + + SENSOR_ATTR_2(pwm2_auto_channels_temp, S_IRUGO|S_IWUSR, + show_pwm_auto_point_channel, + store_pwm_auto_point_channel, 0, 1), + SENSOR_ATTR_2(pwm2_auto_point1_pwm, S_IRUGO|S_IWUSR, + show_pwm_auto_point_pwm, store_pwm_auto_point_pwm, + 0, 1), + SENSOR_ATTR_2(pwm2_auto_point2_pwm, S_IRUGO|S_IWUSR, + show_pwm_auto_point_pwm, store_pwm_auto_point_pwm, + 1, 1), + SENSOR_ATTR_2(pwm2_auto_point3_pwm, S_IRUGO|S_IWUSR, + show_pwm_auto_point_pwm, store_pwm_auto_point_pwm, + 4, 1), + SENSOR_ATTR_2(pwm2_auto_point1_temp, S_IRUGO|S_IWUSR, + show_pwm_auto_point_temp, store_pwm_auto_point_temp, + 0, 1), + SENSOR_ATTR_2(pwm2_auto_point2_temp, S_IRUGO|S_IWUSR, + show_pwm_auto_point_temp, store_pwm_auto_point_temp, + 3, 1), + SENSOR_ATTR_2(pwm2_auto_point1_temp_hyst, S_IRUGO|S_IWUSR, + show_pwm_auto_point_temp_hyst, + store_pwm_auto_point_temp_hyst, + 0, 1), + SENSOR_ATTR_2(pwm2_auto_point2_temp_hyst, S_IRUGO, + show_pwm_auto_point_temp_hyst, NULL, 3, 1), + + SENSOR_ATTR_2(pwm3_auto_channels_temp, S_IRUGO|S_IWUSR, + show_pwm_auto_point_channel, + store_pwm_auto_point_channel, 0, 2), + SENSOR_ATTR_2(pwm3_auto_point1_pwm, S_IRUGO|S_IWUSR, + show_pwm_auto_point_pwm, store_pwm_auto_point_pwm, + 0, 2), + SENSOR_ATTR_2(pwm3_auto_point2_pwm, S_IRUGO|S_IWUSR, + show_pwm_auto_point_pwm, store_pwm_auto_point_pwm, + 1, 2), + SENSOR_ATTR_2(pwm3_auto_point3_pwm, S_IRUGO|S_IWUSR, + show_pwm_auto_point_pwm, store_pwm_auto_point_pwm, + 4, 2), + SENSOR_ATTR_2(pwm3_auto_point1_temp, S_IRUGO|S_IWUSR, + show_pwm_auto_point_temp, store_pwm_auto_point_temp, + 0, 2), + SENSOR_ATTR_2(pwm3_auto_point2_temp, S_IRUGO|S_IWUSR, + show_pwm_auto_point_temp, store_pwm_auto_point_temp, + 3, 2), + SENSOR_ATTR_2(pwm3_auto_point1_temp_hyst, S_IRUGO|S_IWUSR, + show_pwm_auto_point_temp_hyst, + store_pwm_auto_point_temp_hyst, + 0, 2), + SENSOR_ATTR_2(pwm3_auto_point2_temp_hyst, S_IRUGO, + show_pwm_auto_point_temp_hyst, NULL, 3, 2), +}; + +/* PWM attr for the standard models */ static struct sensor_device_attribute_2 fxxxx_auto_pwm_attr[4][14] = { { SENSOR_ATTR_2(pwm1_auto_channels_temp, S_IRUGO|S_IWUSR, show_pwm_auto_point_channel, @@ -943,16 +1071,16 @@ static u16 f71882fg_read_temp(struct f71882fg_data *data, int nr) static struct f71882fg_data *f71882fg_update_device(struct device *dev) { struct f71882fg_data *data = dev_get_drvdata(dev); - int nr, reg = 0, reg2; + int nr, reg, point; int nr_fans = (data->type == f71882fg) ? 4 : 3; - int nr_ins = (data->type == f71858fg || data->type == f8000) ? 3 : 9; + int nr_temps = (data->type == f71808e) ? 2 : 3; mutex_lock(&data->update_lock); /* Update once every 60 seconds */ if (time_after(jiffies, data->last_limits + 60 * HZ) || !data->valid) { - if (data->type == f71882fg || data->type == f71889fg) { + if (f71882fg_has_in1_alarm[data->type]) { data->in1_max = f71882fg_read8(data, F71882FG_REG_IN1_HIGH); data->in_beep = @@ -960,7 +1088,8 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev) } /* Get High & boundary temps*/ - for (nr = data->temp_start; nr < 3 + data->temp_start; nr++) { + for (nr = data->temp_start; nr < nr_temps + data->temp_start; + nr++) { data->temp_ovt[nr] = f71882fg_read8(data, F71882FG_REG_TEMP_OVT(nr)); data->temp_high[nr] = f71882fg_read8(data, @@ -973,44 +1102,19 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev) data->temp_hyst[1] = f71882fg_read8(data, F71882FG_REG_TEMP_HYST(1)); } + /* All but the f71858fg / f8000 have this register */ + if ((data->type != f71858fg) && (data->type != f8000)) { + reg = f71882fg_read8(data, F71882FG_REG_TEMP_TYPE); + data->temp_type[1] = (reg & 0x02) ? 2 : 4; + data->temp_type[2] = (reg & 0x04) ? 2 : 4; + data->temp_type[3] = (reg & 0x08) ? 2 : 4; + } - if (data->type == f71862fg || data->type == f71882fg || - data->type == f71889fg) { + if (f71882fg_has_beep[data->type]) { data->fan_beep = f71882fg_read8(data, F71882FG_REG_FAN_BEEP); data->temp_beep = f71882fg_read8(data, F71882FG_REG_TEMP_BEEP); - /* Have to hardcode type, because temp1 is special */ - reg = f71882fg_read8(data, F71882FG_REG_TEMP_TYPE); - data->temp_type[2] = (reg & 0x04) ? 2 : 4; - data->temp_type[3] = (reg & 0x08) ? 2 : 4; - } - /* Determine temp index 1 sensor type */ - if (data->type == f71889fg) { - reg2 = f71882fg_read8(data, F71882FG_REG_START); - switch ((reg2 & 0x60) >> 5) { - case 0x00: /* BJT / Thermistor */ - data->temp_type[1] = (reg & 0x02) ? 2 : 4; - break; - case 0x01: /* AMDSI */ - data->temp_type[1] = 5; - break; - case 0x02: /* PECI */ - case 0x03: /* Ibex Peak ?? Report as PECI for now */ - data->temp_type[1] = 6; - break; - } - } else { - reg2 = f71882fg_read8(data, F71882FG_REG_PECI); - if ((reg2 & 0x03) == 0x01) - data->temp_type[1] = 6; /* PECI */ - else if ((reg2 & 0x03) == 0x02) - data->temp_type[1] = 5; /* AMDSI */ - else if (data->type == f71862fg || - data->type == f71882fg) - data->temp_type[1] = (reg & 0x02) ? 2 : 4; - else /* f71858fg and f8000 only support BJT */ - data->temp_type[1] = 2; } data->pwm_enable = f71882fg_read8(data, @@ -1025,8 +1129,8 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev) f71882fg_read8(data, F71882FG_REG_POINT_MAPPING(nr)); - if (data->type != f71862fg) { - int point; + switch (data->type) { + default: for (point = 0; point < 5; point++) { data->pwm_auto_point_pwm[nr][point] = f71882fg_read8(data, @@ -1039,7 +1143,14 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev) F71882FG_REG_POINT_TEMP (nr, point)); } - } else { + break; + case f71808e: + case f71869: + data->pwm_auto_point_pwm[nr][0] = + f71882fg_read8(data, + F71882FG_REG_POINT_PWM(nr, 0)); + /* Fall through */ + case f71862fg: data->pwm_auto_point_pwm[nr][1] = f71882fg_read8(data, F71882FG_REG_POINT_PWM @@ -1056,6 +1167,7 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev) f71882fg_read8(data, F71882FG_REG_POINT_TEMP (nr, 3)); + break; } } data->last_limits = jiffies; @@ -1067,7 +1179,8 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev) F71882FG_REG_TEMP_STATUS); data->temp_diode_open = f71882fg_read8(data, F71882FG_REG_TEMP_DIODE_OPEN); - for (nr = data->temp_start; nr < 3 + data->temp_start; nr++) + for (nr = data->temp_start; nr < nr_temps + data->temp_start; + nr++) data->temp[nr] = f71882fg_read_temp(data, nr); data->fan_status = f71882fg_read8(data, @@ -1083,17 +1196,18 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev) data->pwm[nr] = f71882fg_read8(data, F71882FG_REG_PWM(nr)); } - /* The f8000 can monitor 1 more fan, but has no pwm for it */ if (data->type == f8000) data->fan[3] = f71882fg_read16(data, F71882FG_REG_FAN(3)); - if (data->type == f71882fg || data->type == f71889fg) + + if (f71882fg_has_in1_alarm[data->type]) data->in_status = f71882fg_read8(data, F71882FG_REG_IN_STATUS); - for (nr = 0; nr < nr_ins; nr++) - data->in[nr] = f71882fg_read8(data, - F71882FG_REG_IN(nr)); + for (nr = 0; nr < F71882FG_MAX_INS; nr++) + if (f71882fg_has_in[data->type][nr]) + data->in[nr] = f71882fg_read8(data, + F71882FG_REG_IN(nr)); data->last_updated = jiffies; data->valid = 1; @@ -1882,7 +1996,7 @@ static ssize_t store_pwm_auto_point_temp(struct device *dev, val /= 1000; - if (data->type == f71889fg) + if (data->auto_point_temp_signed) val = SENSORS_LIMIT(val, -128, 127); else val = SENSORS_LIMIT(val, 0, 127); @@ -1929,7 +2043,8 @@ static int __devinit f71882fg_probe(struct platform_device *pdev) struct f71882fg_data *data; struct f71882fg_sio_data *sio_data = pdev->dev.platform_data; int err, i, nr_fans = (sio_data->type == f71882fg) ? 4 : 3; - u8 start_reg; + int nr_temps = (sio_data->type == f71808e) ? 2 : 3; + u8 start_reg, reg; data = kzalloc(sizeof(struct f71882fg_data), GFP_KERNEL); if (!data) @@ -1968,37 +2083,72 @@ static int __devinit f71882fg_probe(struct platform_device *pdev) /* The f71858fg temperature alarms behave as the f8000 alarms in this mode */ err = f71882fg_create_sysfs_files(pdev, - f8000_in_temp_attr, - ARRAY_SIZE(f8000_in_temp_attr)); + f8000_temp_attr, + ARRAY_SIZE(f8000_temp_attr)); else err = f71882fg_create_sysfs_files(pdev, - f71858fg_in_temp_attr, - ARRAY_SIZE(f71858fg_in_temp_attr)); - break; - case f71882fg: - case f71889fg: - err = f71882fg_create_sysfs_files(pdev, - fxxxx_in1_alarm_attr, - ARRAY_SIZE(fxxxx_in1_alarm_attr)); - if (err) - goto exit_unregister_sysfs; - /* fall through! */ - case f71862fg: - err = f71882fg_create_sysfs_files(pdev, - fxxxx_in_temp_attr, - ARRAY_SIZE(fxxxx_in_temp_attr)); + f71858fg_temp_attr, + ARRAY_SIZE(f71858fg_temp_attr)); break; case f8000: err = f71882fg_create_sysfs_files(pdev, - f8000_in_temp_attr, - ARRAY_SIZE(f8000_in_temp_attr)); + f8000_temp_attr, + ARRAY_SIZE(f8000_temp_attr)); break; + default: + err = f71882fg_create_sysfs_files(pdev, + &fxxxx_temp_attr[0][0], + ARRAY_SIZE(fxxxx_temp_attr[0]) * nr_temps); } if (err) goto exit_unregister_sysfs; + + if (f71882fg_has_beep[data->type]) { + err = f71882fg_create_sysfs_files(pdev, + &fxxxx_temp_beep_attr[0][0], + ARRAY_SIZE(fxxxx_temp_beep_attr[0]) + * nr_temps); + if (err) + goto exit_unregister_sysfs; + } + + for (i = 0; i < F71882FG_MAX_INS; i++) { + if (f71882fg_has_in[data->type][i]) { + err = device_create_file(&pdev->dev, + &fxxxx_in_attr[i].dev_attr); + if (err) + goto exit_unregister_sysfs; + } + } + if (f71882fg_has_in1_alarm[data->type]) { + err = f71882fg_create_sysfs_files(pdev, + fxxxx_in1_alarm_attr, + ARRAY_SIZE(fxxxx_in1_alarm_attr)); + if (err) + goto exit_unregister_sysfs; + } } if (start_reg & 0x02) { + switch (data->type) { + case f71808e: + case f71869: + /* These always have signed auto point temps */ + data->auto_point_temp_signed = 1; + /* Fall through to select correct fan/pwm reg bank! */ + case f71889fg: + case f71889ed: + reg = f71882fg_read8(data, F71882FG_REG_FAN_FAULT_T); + if (reg & F71882FG_FAN_NEG_TEMP_EN) + data->auto_point_temp_signed = 1; + /* Ensure banked pwm registers point to right bank */ + reg &= ~F71882FG_FAN_PROG_SEL; + f71882fg_write8(data, F71882FG_REG_FAN_FAULT_T, reg); + break; + default: + break; + } + data->pwm_enable = f71882fg_read8(data, F71882FG_REG_PWM_ENABLE); @@ -2013,8 +2163,11 @@ static int __devinit f71882fg_probe(struct platform_device *pdev) case f71862fg: err = (data->pwm_enable & 0x15) != 0x15; break; + case f71808e: + case f71869: case f71882fg: case f71889fg: + case f71889ed: err = 0; break; case f8000: @@ -2034,8 +2187,7 @@ static int __devinit f71882fg_probe(struct platform_device *pdev) if (err) goto exit_unregister_sysfs; - if (data->type == f71862fg || data->type == f71882fg || - data->type == f71889fg) { + if (f71882fg_has_beep[data->type]) { err = f71882fg_create_sysfs_files(pdev, fxxxx_fan_beep_attr, nr_fans); if (err) @@ -2043,11 +2195,42 @@ static int __devinit f71882fg_probe(struct platform_device *pdev) } switch (data->type) { + case f71808e: + case f71869: + case f71889fg: + case f71889ed: + for (i = 0; i < nr_fans; i++) { + data->pwm_auto_point_mapping[i] = + f71882fg_read8(data, + F71882FG_REG_POINT_MAPPING(i)); + if ((data->pwm_auto_point_mapping[i] & 0x80) || + (data->pwm_auto_point_mapping[i] & 3) == 0) + break; + } + if (i != nr_fans) { + dev_warn(&pdev->dev, + "Auto pwm controlled by raw digital " + "data, disabling pwm auto_point " + "sysfs attributes\n"); + goto no_pwm_auto_point; + } + break; + default: + break; + } + + switch (data->type) { case f71862fg: err = f71882fg_create_sysfs_files(pdev, f71862fg_auto_pwm_attr, ARRAY_SIZE(f71862fg_auto_pwm_attr)); break; + case f71808e: + case f71869: + err = f71882fg_create_sysfs_files(pdev, + f71869_auto_pwm_attr, + ARRAY_SIZE(f71869_auto_pwm_attr)); + break; case f8000: err = f71882fg_create_sysfs_files(pdev, f8000_fan_attr, @@ -2058,23 +2241,7 @@ static int __devinit f71882fg_probe(struct platform_device *pdev) f8000_auto_pwm_attr, ARRAY_SIZE(f8000_auto_pwm_attr)); break; - case f71889fg: - for (i = 0; i < nr_fans; i++) { - data->pwm_auto_point_mapping[i] = - f71882fg_read8(data, - F71882FG_REG_POINT_MAPPING(i)); - if (data->pwm_auto_point_mapping[i] & 0x80) - break; - } - if (i != nr_fans) { - dev_warn(&pdev->dev, - "Auto pwm controlled by raw digital " - "data, disabling pwm auto_point " - "sysfs attributes\n"); - break; - } - /* fall through */ - default: /* f71858fg / f71882fg */ + default: err = f71882fg_create_sysfs_files(pdev, &fxxxx_auto_pwm_attr[0][0], ARRAY_SIZE(fxxxx_auto_pwm_attr[0]) * nr_fans); @@ -2082,6 +2249,7 @@ static int __devinit f71882fg_probe(struct platform_device *pdev) if (err) goto exit_unregister_sysfs; +no_pwm_auto_point: for (i = 0; i < nr_fans; i++) dev_info(&pdev->dev, "Fan: %d is in %s mode\n", i + 1, (data->pwm_enable & (1 << 2 * i)) ? @@ -2108,7 +2276,8 @@ exit_free: static int f71882fg_remove(struct platform_device *pdev) { struct f71882fg_data *data = platform_get_drvdata(pdev); - int nr_fans = (data->type == f71882fg) ? 4 : 3; + int i, nr_fans = (data->type == f71882fg) ? 4 : 3; + int nr_temps = (data->type == f71808e) ? 2 : 3; u8 start_reg = f71882fg_read8(data, F71882FG_REG_START); if (data->hwmon_dev) @@ -2121,29 +2290,39 @@ static int f71882fg_remove(struct platform_device *pdev) case f71858fg: if (data->temp_config & 0x10) f71882fg_remove_sysfs_files(pdev, - f8000_in_temp_attr, - ARRAY_SIZE(f8000_in_temp_attr)); + f8000_temp_attr, + ARRAY_SIZE(f8000_temp_attr)); else f71882fg_remove_sysfs_files(pdev, - f71858fg_in_temp_attr, - ARRAY_SIZE(f71858fg_in_temp_attr)); - break; - case f71882fg: - case f71889fg: - f71882fg_remove_sysfs_files(pdev, - fxxxx_in1_alarm_attr, - ARRAY_SIZE(fxxxx_in1_alarm_attr)); - /* fall through! */ - case f71862fg: - f71882fg_remove_sysfs_files(pdev, - fxxxx_in_temp_attr, - ARRAY_SIZE(fxxxx_in_temp_attr)); + f71858fg_temp_attr, + ARRAY_SIZE(f71858fg_temp_attr)); break; case f8000: f71882fg_remove_sysfs_files(pdev, - f8000_in_temp_attr, - ARRAY_SIZE(f8000_in_temp_attr)); + f8000_temp_attr, + ARRAY_SIZE(f8000_temp_attr)); break; + default: + f71882fg_remove_sysfs_files(pdev, + &fxxxx_temp_attr[0][0], + ARRAY_SIZE(fxxxx_temp_attr[0]) * nr_temps); + } + if (f71882fg_has_beep[data->type]) { + f71882fg_remove_sysfs_files(pdev, + &fxxxx_temp_beep_attr[0][0], + ARRAY_SIZE(fxxxx_temp_beep_attr[0]) * nr_temps); + } + + for (i = 0; i < F71882FG_MAX_INS; i++) { + if (f71882fg_has_in[data->type][i]) { + device_remove_file(&pdev->dev, + &fxxxx_in_attr[i].dev_attr); + } + } + if (f71882fg_has_in1_alarm[data->type]) { + f71882fg_remove_sysfs_files(pdev, + fxxxx_in1_alarm_attr, + ARRAY_SIZE(fxxxx_in1_alarm_attr)); } } @@ -2151,10 +2330,10 @@ static int f71882fg_remove(struct platform_device *pdev) f71882fg_remove_sysfs_files(pdev, &fxxxx_fan_attr[0][0], ARRAY_SIZE(fxxxx_fan_attr[0]) * nr_fans); - if (data->type == f71862fg || data->type == f71882fg || - data->type == f71889fg) + if (f71882fg_has_beep[data->type]) { f71882fg_remove_sysfs_files(pdev, fxxxx_fan_beep_attr, nr_fans); + } switch (data->type) { case f71862fg: @@ -2162,6 +2341,12 @@ static int f71882fg_remove(struct platform_device *pdev) f71862fg_auto_pwm_attr, ARRAY_SIZE(f71862fg_auto_pwm_attr)); break; + case f71808e: + case f71869: + f71882fg_remove_sysfs_files(pdev, + f71869_auto_pwm_attr, + ARRAY_SIZE(f71869_auto_pwm_attr)); + break; case f8000: f71882fg_remove_sysfs_files(pdev, f8000_fan_attr, @@ -2170,7 +2355,7 @@ static int f71882fg_remove(struct platform_device *pdev) f8000_auto_pwm_attr, ARRAY_SIZE(f8000_auto_pwm_attr)); break; - default: /* f71858fg / f71882fg / f71889fg */ + default: f71882fg_remove_sysfs_files(pdev, &fxxxx_auto_pwm_attr[0][0], ARRAY_SIZE(fxxxx_auto_pwm_attr[0]) * nr_fans); @@ -2200,18 +2385,27 @@ static int __init f71882fg_find(int sioaddr, unsigned short *address, devid = force_id ? force_id : superio_inw(sioaddr, SIO_REG_DEVID); switch (devid) { + case SIO_F71808E_ID: + sio_data->type = f71808e; + break; case SIO_F71858_ID: sio_data->type = f71858fg; break; case SIO_F71862_ID: sio_data->type = f71862fg; break; + case SIO_F71869_ID: + sio_data->type = f71869; + break; case SIO_F71882_ID: sio_data->type = f71882fg; break; case SIO_F71889_ID: sio_data->type = f71889fg; break; + case SIO_F71889E_ID: + sio_data->type = f71889ed; + break; case SIO_F8000_ID: sio_data->type = f8000; break; diff --git a/drivers/hwmon/lineage-pem.c b/drivers/hwmon/lineage-pem.c new file mode 100644 index 00000000000..58eded27f38 --- /dev/null +++ b/drivers/hwmon/lineage-pem.c @@ -0,0 +1,586 @@ +/* + * Driver for Lineage Compact Power Line series of power entry modules. + * + * Copyright (C) 2010, 2011 Ericsson AB. + * + * Documentation: + * http://www.lineagepower.com/oem/pdf/CPLI2C.pdf + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> + +/* + * This driver supports various Lineage Compact Power Line DC/DC and AC/DC + * converters such as CP1800, CP2000AC, CP2000DC, CP2100DC, and others. + * + * The devices are nominally PMBus compliant. However, most standard PMBus + * commands are not supported. Specifically, all hardware monitoring and + * status reporting commands are non-standard. For this reason, a standard + * PMBus driver can not be used. + * + * All Lineage CPL devices have a built-in I2C bus master selector (PCA9541). + * To ensure device access, this driver should only be used as client driver + * to the pca9541 I2C master selector driver. + */ + +/* Command codes */ +#define PEM_OPERATION 0x01 +#define PEM_CLEAR_INFO_FLAGS 0x03 +#define PEM_VOUT_COMMAND 0x21 +#define PEM_VOUT_OV_FAULT_LIMIT 0x40 +#define PEM_READ_DATA_STRING 0xd0 +#define PEM_READ_INPUT_STRING 0xdc +#define PEM_READ_FIRMWARE_REV 0xdd +#define PEM_READ_RUN_TIMER 0xde +#define PEM_FAN_HI_SPEED 0xdf +#define PEM_FAN_NORMAL_SPEED 0xe0 +#define PEM_READ_FAN_SPEED 0xe1 + +/* offsets in data string */ +#define PEM_DATA_STATUS_2 0 +#define PEM_DATA_STATUS_1 1 +#define PEM_DATA_ALARM_2 2 +#define PEM_DATA_ALARM_1 3 +#define PEM_DATA_VOUT_LSB 4 +#define PEM_DATA_VOUT_MSB 5 +#define PEM_DATA_CURRENT 6 +#define PEM_DATA_TEMP 7 + +/* Virtual entries, to report constants */ +#define PEM_DATA_TEMP_MAX 10 +#define PEM_DATA_TEMP_CRIT 11 + +/* offsets in input string */ +#define PEM_INPUT_VOLTAGE 0 +#define PEM_INPUT_POWER_LSB 1 +#define PEM_INPUT_POWER_MSB 2 + +/* offsets in fan data */ +#define PEM_FAN_ADJUSTMENT 0 +#define PEM_FAN_FAN1 1 +#define PEM_FAN_FAN2 2 +#define PEM_FAN_FAN3 3 + +/* Status register bits */ +#define STS1_OUTPUT_ON (1 << 0) +#define STS1_LEDS_FLASHING (1 << 1) +#define STS1_EXT_FAULT (1 << 2) +#define STS1_SERVICE_LED_ON (1 << 3) +#define STS1_SHUTDOWN_OCCURRED (1 << 4) +#define STS1_INT_FAULT (1 << 5) +#define STS1_ISOLATION_TEST_OK (1 << 6) + +#define STS2_ENABLE_PIN_HI (1 << 0) +#define STS2_DATA_OUT_RANGE (1 << 1) +#define STS2_RESTARTED_OK (1 << 1) +#define STS2_ISOLATION_TEST_FAIL (1 << 3) +#define STS2_HIGH_POWER_CAP (1 << 4) +#define STS2_INVALID_INSTR (1 << 5) +#define STS2_WILL_RESTART (1 << 6) +#define STS2_PEC_ERR (1 << 7) + +/* Alarm register bits */ +#define ALRM1_VIN_OUT_LIMIT (1 << 0) +#define ALRM1_VOUT_OUT_LIMIT (1 << 1) +#define ALRM1_OV_VOLT_SHUTDOWN (1 << 2) +#define ALRM1_VIN_OVERCURRENT (1 << 3) +#define ALRM1_TEMP_WARNING (1 << 4) +#define ALRM1_TEMP_SHUTDOWN (1 << 5) +#define ALRM1_PRIMARY_FAULT (1 << 6) +#define ALRM1_POWER_LIMIT (1 << 7) + +#define ALRM2_5V_OUT_LIMIT (1 << 1) +#define ALRM2_TEMP_FAULT (1 << 2) +#define ALRM2_OV_LOW (1 << 3) +#define ALRM2_DCDC_TEMP_HIGH (1 << 4) +#define ALRM2_PRI_TEMP_HIGH (1 << 5) +#define ALRM2_NO_PRIMARY (1 << 6) +#define ALRM2_FAN_FAULT (1 << 7) + +#define FIRMWARE_REV_LEN 4 +#define DATA_STRING_LEN 9 +#define INPUT_STRING_LEN 5 /* 4 for most devices */ +#define FAN_SPEED_LEN 5 + +struct pem_data { + struct device *hwmon_dev; + + struct mutex update_lock; + bool valid; + bool fans_supported; + int input_length; + unsigned long last_updated; /* in jiffies */ + + u8 firmware_rev[FIRMWARE_REV_LEN]; + u8 data_string[DATA_STRING_LEN]; + u8 input_string[INPUT_STRING_LEN]; + u8 fan_speed[FAN_SPEED_LEN]; +}; + +static int pem_read_block(struct i2c_client *client, u8 command, u8 *data, + int data_len) +{ + u8 block_buffer[I2C_SMBUS_BLOCK_MAX]; + int result; + + result = i2c_smbus_read_block_data(client, command, block_buffer); + if (unlikely(result < 0)) + goto abort; + if (unlikely(result == 0xff || result != data_len)) { + result = -EIO; + goto abort; + } + memcpy(data, block_buffer, data_len); + result = 0; +abort: + return result; +} + +static struct pem_data *pem_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct pem_data *data = i2c_get_clientdata(client); + struct pem_data *ret = data; + + mutex_lock(&data->update_lock); + + if (time_after(jiffies, data->last_updated + HZ) || !data->valid) { + int result; + + /* Read data string */ + result = pem_read_block(client, PEM_READ_DATA_STRING, + data->data_string, + sizeof(data->data_string)); + if (unlikely(result < 0)) { + ret = ERR_PTR(result); + goto abort; + } + + /* Read input string */ + if (data->input_length) { + result = pem_read_block(client, PEM_READ_INPUT_STRING, + data->input_string, + data->input_length); + if (unlikely(result < 0)) { + ret = ERR_PTR(result); + goto abort; + } + } + + /* Read fan speeds */ + if (data->fans_supported) { + result = pem_read_block(client, PEM_READ_FAN_SPEED, + data->fan_speed, + sizeof(data->fan_speed)); + if (unlikely(result < 0)) { + ret = ERR_PTR(result); + goto abort; + } + } + + i2c_smbus_write_byte(client, PEM_CLEAR_INFO_FLAGS); + + data->last_updated = jiffies; + data->valid = 1; + } +abort: + mutex_unlock(&data->update_lock); + return ret; +} + +static long pem_get_data(u8 *data, int len, int index) +{ + long val; + + switch (index) { + case PEM_DATA_VOUT_LSB: + val = (data[index] + (data[index+1] << 8)) * 5 / 2; + break; + case PEM_DATA_CURRENT: + val = data[index] * 200; + break; + case PEM_DATA_TEMP: + val = data[index] * 1000; + break; + case PEM_DATA_TEMP_MAX: + val = 97 * 1000; /* 97 degrees C per datasheet */ + break; + case PEM_DATA_TEMP_CRIT: + val = 107 * 1000; /* 107 degrees C per datasheet */ + break; + default: + WARN_ON_ONCE(1); + val = 0; + } + return val; +} + +static long pem_get_input(u8 *data, int len, int index) +{ + long val; + + switch (index) { + case PEM_INPUT_VOLTAGE: + if (len == INPUT_STRING_LEN) + val = (data[index] + (data[index+1] << 8) - 75) * 1000; + else + val = (data[index] - 75) * 1000; + break; + case PEM_INPUT_POWER_LSB: + if (len == INPUT_STRING_LEN) + index++; + val = (data[index] + (data[index+1] << 8)) * 1000000L; + break; + default: + WARN_ON_ONCE(1); + val = 0; + } + return val; +} + +static long pem_get_fan(u8 *data, int len, int index) +{ + long val; + + switch (index) { + case PEM_FAN_FAN1: + case PEM_FAN_FAN2: + case PEM_FAN_FAN3: + val = data[index] * 100; + break; + default: + WARN_ON_ONCE(1); + val = 0; + } + return val; +} + +/* + * Show boolean, either a fault or an alarm. + * .nr points to the register, .index is the bit mask to check + */ +static ssize_t pem_show_bool(struct device *dev, + struct device_attribute *da, char *buf) +{ + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(da); + struct pem_data *data = pem_update_device(dev); + u8 status; + + if (IS_ERR(data)) + return PTR_ERR(data); + + status = data->data_string[attr->nr] & attr->index; + return snprintf(buf, PAGE_SIZE, "%d\n", !!status); +} + +static ssize_t pem_show_data(struct device *dev, struct device_attribute *da, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); + struct pem_data *data = pem_update_device(dev); + long value; + + if (IS_ERR(data)) + return PTR_ERR(data); + + value = pem_get_data(data->data_string, sizeof(data->data_string), + attr->index); + + return snprintf(buf, PAGE_SIZE, "%ld\n", value); +} + +static ssize_t pem_show_input(struct device *dev, struct device_attribute *da, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); + struct pem_data *data = pem_update_device(dev); + long value; + + if (IS_ERR(data)) + return PTR_ERR(data); + + value = pem_get_input(data->input_string, sizeof(data->input_string), + attr->index); + + return snprintf(buf, PAGE_SIZE, "%ld\n", value); +} + +static ssize_t pem_show_fan(struct device *dev, struct device_attribute *da, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); + struct pem_data *data = pem_update_device(dev); + long value; + + if (IS_ERR(data)) + return PTR_ERR(data); + + value = pem_get_fan(data->fan_speed, sizeof(data->fan_speed), + attr->index); + + return snprintf(buf, PAGE_SIZE, "%ld\n", value); +} + +/* Voltages */ +static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, pem_show_data, NULL, + PEM_DATA_VOUT_LSB); +static SENSOR_DEVICE_ATTR_2(in1_alarm, S_IRUGO, pem_show_bool, NULL, + PEM_DATA_ALARM_1, ALRM1_VOUT_OUT_LIMIT); +static SENSOR_DEVICE_ATTR_2(in1_crit_alarm, S_IRUGO, pem_show_bool, NULL, + PEM_DATA_ALARM_1, ALRM1_OV_VOLT_SHUTDOWN); +static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, pem_show_input, NULL, + PEM_INPUT_VOLTAGE); +static SENSOR_DEVICE_ATTR_2(in2_alarm, S_IRUGO, pem_show_bool, NULL, + PEM_DATA_ALARM_1, + ALRM1_VIN_OUT_LIMIT | ALRM1_PRIMARY_FAULT); + +/* Currents */ +static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, pem_show_data, NULL, + PEM_DATA_CURRENT); +static SENSOR_DEVICE_ATTR_2(curr1_alarm, S_IRUGO, pem_show_bool, NULL, + PEM_DATA_ALARM_1, ALRM1_VIN_OVERCURRENT); + +/* Power */ +static SENSOR_DEVICE_ATTR(power1_input, S_IRUGO, pem_show_input, NULL, + PEM_INPUT_POWER_LSB); +static SENSOR_DEVICE_ATTR_2(power1_alarm, S_IRUGO, pem_show_bool, NULL, + PEM_DATA_ALARM_1, ALRM1_POWER_LIMIT); + +/* Fans */ +static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, pem_show_fan, NULL, + PEM_FAN_FAN1); +static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, pem_show_fan, NULL, + PEM_FAN_FAN2); +static SENSOR_DEVICE_ATTR(fan3_input, S_IRUGO, pem_show_fan, NULL, + PEM_FAN_FAN3); +static SENSOR_DEVICE_ATTR_2(fan1_alarm, S_IRUGO, pem_show_bool, NULL, + PEM_DATA_ALARM_2, ALRM2_FAN_FAULT); + +/* Temperatures */ +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, pem_show_data, NULL, + PEM_DATA_TEMP); +static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO, pem_show_data, NULL, + PEM_DATA_TEMP_MAX); +static SENSOR_DEVICE_ATTR(temp1_crit, S_IRUGO, pem_show_data, NULL, + PEM_DATA_TEMP_CRIT); +static SENSOR_DEVICE_ATTR_2(temp1_alarm, S_IRUGO, pem_show_bool, NULL, + PEM_DATA_ALARM_1, ALRM1_TEMP_WARNING); +static SENSOR_DEVICE_ATTR_2(temp1_crit_alarm, S_IRUGO, pem_show_bool, NULL, + PEM_DATA_ALARM_1, ALRM1_TEMP_SHUTDOWN); +static SENSOR_DEVICE_ATTR_2(temp1_fault, S_IRUGO, pem_show_bool, NULL, + PEM_DATA_ALARM_2, ALRM2_TEMP_FAULT); + +static struct attribute *pem_attributes[] = { + &sensor_dev_attr_in1_input.dev_attr.attr, + &sensor_dev_attr_in1_alarm.dev_attr.attr, + &sensor_dev_attr_in1_crit_alarm.dev_attr.attr, + &sensor_dev_attr_in2_alarm.dev_attr.attr, + + &sensor_dev_attr_curr1_alarm.dev_attr.attr, + + &sensor_dev_attr_power1_alarm.dev_attr.attr, + + &sensor_dev_attr_fan1_alarm.dev_attr.attr, + + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_temp1_max.dev_attr.attr, + &sensor_dev_attr_temp1_crit.dev_attr.attr, + &sensor_dev_attr_temp1_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_fault.dev_attr.attr, + + NULL, +}; + +static const struct attribute_group pem_group = { + .attrs = pem_attributes, +}; + +static struct attribute *pem_input_attributes[] = { + &sensor_dev_attr_in2_input.dev_attr.attr, + &sensor_dev_attr_curr1_input.dev_attr.attr, + &sensor_dev_attr_power1_input.dev_attr.attr, +}; + +static const struct attribute_group pem_input_group = { + .attrs = pem_input_attributes, +}; + +static struct attribute *pem_fan_attributes[] = { + &sensor_dev_attr_fan1_input.dev_attr.attr, + &sensor_dev_attr_fan2_input.dev_attr.attr, + &sensor_dev_attr_fan3_input.dev_attr.attr, +}; + +static const struct attribute_group pem_fan_group = { + .attrs = pem_fan_attributes, +}; + +static int pem_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adapter = client->adapter; + struct pem_data *data; + int ret; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BLOCK_DATA + | I2C_FUNC_SMBUS_WRITE_BYTE)) + return -ENODEV; + + data = kzalloc(sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + + /* + * We use the next two commands to determine if the device is really + * there. + */ + ret = pem_read_block(client, PEM_READ_FIRMWARE_REV, + data->firmware_rev, sizeof(data->firmware_rev)); + if (ret < 0) + goto out_kfree; + + ret = i2c_smbus_write_byte(client, PEM_CLEAR_INFO_FLAGS); + if (ret < 0) + goto out_kfree; + + dev_info(&client->dev, "Firmware revision %d.%d.%d\n", + data->firmware_rev[0], data->firmware_rev[1], + data->firmware_rev[2]); + + /* Register sysfs hooks */ + ret = sysfs_create_group(&client->dev.kobj, &pem_group); + if (ret) + goto out_kfree; + + /* + * Check if input readings are supported. + * This is the case if we can read input data, + * and if the returned data is not all zeros. + * Note that input alarms are always supported. + */ + ret = pem_read_block(client, PEM_READ_INPUT_STRING, + data->input_string, + sizeof(data->input_string) - 1); + if (!ret && (data->input_string[0] || data->input_string[1] || + data->input_string[2])) + data->input_length = sizeof(data->input_string) - 1; + else if (ret < 0) { + /* Input string is one byte longer for some devices */ + ret = pem_read_block(client, PEM_READ_INPUT_STRING, + data->input_string, + sizeof(data->input_string)); + if (!ret && (data->input_string[0] || data->input_string[1] || + data->input_string[2] || data->input_string[3])) + data->input_length = sizeof(data->input_string); + } + ret = 0; + if (data->input_length) { + ret = sysfs_create_group(&client->dev.kobj, &pem_input_group); + if (ret) + goto out_remove_groups; + } + + /* + * Check if fan speed readings are supported. + * This is the case if we can read fan speed data, + * and if the returned data is not all zeros. + * Note that the fan alarm is always supported. + */ + ret = pem_read_block(client, PEM_READ_FAN_SPEED, + data->fan_speed, + sizeof(data->fan_speed)); + if (!ret && (data->fan_speed[0] || data->fan_speed[1] || + data->fan_speed[2] || data->fan_speed[3])) { + data->fans_supported = true; + ret = sysfs_create_group(&client->dev.kobj, &pem_fan_group); + if (ret) + goto out_remove_groups; + } + + data->hwmon_dev = hwmon_device_register(&client->dev); + if (IS_ERR(data->hwmon_dev)) { + ret = PTR_ERR(data->hwmon_dev); + goto out_remove_groups; + } + + return 0; + +out_remove_groups: + sysfs_remove_group(&client->dev.kobj, &pem_input_group); + sysfs_remove_group(&client->dev.kobj, &pem_fan_group); + sysfs_remove_group(&client->dev.kobj, &pem_group); +out_kfree: + kfree(data); + return ret; +} + +static int pem_remove(struct i2c_client *client) +{ + struct pem_data *data = i2c_get_clientdata(client); + + hwmon_device_unregister(data->hwmon_dev); + + sysfs_remove_group(&client->dev.kobj, &pem_input_group); + sysfs_remove_group(&client->dev.kobj, &pem_fan_group); + sysfs_remove_group(&client->dev.kobj, &pem_group); + + kfree(data); + return 0; +} + +static const struct i2c_device_id pem_id[] = { + {"lineage_pem", 0}, + {} +}; +MODULE_DEVICE_TABLE(i2c, pem_id); + +static struct i2c_driver pem_driver = { + .driver = { + .name = "lineage_pem", + }, + .probe = pem_probe, + .remove = pem_remove, + .id_table = pem_id, +}; + +static int __init pem_init(void) +{ + return i2c_add_driver(&pem_driver); +} + +static void __exit pem_exit(void) +{ + i2c_del_driver(&pem_driver); +} + +MODULE_AUTHOR("Guenter Roeck <guenter.roeck@ericsson.com>"); +MODULE_DESCRIPTION("Lineage CPL PEM hardware monitoring driver"); +MODULE_LICENSE("GPL"); + +module_init(pem_init); +module_exit(pem_exit); diff --git a/drivers/hwmon/lis3lv02d_spi.c b/drivers/hwmon/lis3lv02d_spi.c index 2549de1de4e..c1f8a8fbf69 100644 --- a/drivers/hwmon/lis3lv02d_spi.c +++ b/drivers/hwmon/lis3lv02d_spi.c @@ -16,6 +16,7 @@ #include <linux/interrupt.h> #include <linux/workqueue.h> #include <linux/spi/spi.h> +#include <linux/pm.h> #include "lis3lv02d.h" @@ -88,9 +89,10 @@ static int __devexit lis302dl_spi_remove(struct spi_device *spi) return lis3lv02d_remove_fs(&lis3_dev); } -#ifdef CONFIG_PM -static int lis3lv02d_spi_suspend(struct spi_device *spi, pm_message_t mesg) +#ifdef CONFIG_PM_SLEEP +static int lis3lv02d_spi_suspend(struct device *dev) { + struct spi_device *spi = to_spi_device(dev); struct lis3lv02d *lis3 = spi_get_drvdata(spi); if (!lis3->pdata || !lis3->pdata->wakeup_flags) @@ -99,8 +101,9 @@ static int lis3lv02d_spi_suspend(struct spi_device *spi, pm_message_t mesg) return 0; } -static int lis3lv02d_spi_resume(struct spi_device *spi) +static int lis3lv02d_spi_resume(struct device *dev) { + struct spi_device *spi = to_spi_device(dev); struct lis3lv02d *lis3 = spi_get_drvdata(spi); if (!lis3->pdata || !lis3->pdata->wakeup_flags) @@ -108,21 +111,19 @@ static int lis3lv02d_spi_resume(struct spi_device *spi) return 0; } - -#else -#define lis3lv02d_spi_suspend NULL -#define lis3lv02d_spi_resume NULL #endif +static SIMPLE_DEV_PM_OPS(lis3lv02d_spi_pm, lis3lv02d_spi_suspend, + lis3lv02d_spi_resume); + static struct spi_driver lis302dl_spi_driver = { .driver = { .name = DRV_NAME, .owner = THIS_MODULE, + .pm = &lis3lv02d_spi_pm, }, .probe = lis302dl_spi_probe, .remove = __devexit_p(lis302dl_spi_remove), - .suspend = lis3lv02d_spi_suspend, - .resume = lis3lv02d_spi_resume, }; static int __init lis302dl_init(void) diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c index d2cc2866081..cf47e6e476e 100644 --- a/drivers/hwmon/lm85.c +++ b/drivers/hwmon/lm85.c @@ -41,7 +41,7 @@ static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; enum chips { any_chip, lm85b, lm85c, adm1027, adt7463, adt7468, - emc6d100, emc6d102, emc6d103 + emc6d100, emc6d102, emc6d103, emc6d103s }; /* The LM85 registers */ @@ -283,10 +283,6 @@ struct lm85_zone { u8 hyst; /* Low limit hysteresis. (0-15) */ u8 range; /* Temp range, encoded */ s8 critical; /* "All fans ON" temp limit */ - u8 off_desired; /* Actual "off" temperature specified. Preserved - * to prevent "drift" as other autofan control - * values change. - */ u8 max_desired; /* Actual "max" temperature specified. Preserved * to prevent "drift" as other autofan control * values change. @@ -306,6 +302,8 @@ struct lm85_data { const int *freq_map; enum chips type; + bool has_vid5; /* true if VID5 is configured for ADT7463 or ADT7468 */ + struct mutex update_lock; int valid; /* !=0 if following fields are valid */ unsigned long last_reading; /* In jiffies */ @@ -352,6 +350,7 @@ static const struct i2c_device_id lm85_id[] = { { "emc6d101", emc6d100 }, { "emc6d102", emc6d102 }, { "emc6d103", emc6d103 }, + { "emc6d103s", emc6d103s }, { } }; MODULE_DEVICE_TABLE(i2c, lm85_id); @@ -420,8 +419,7 @@ static ssize_t show_vid_reg(struct device *dev, struct device_attribute *attr, struct lm85_data *data = lm85_update_device(dev); int vid; - if ((data->type == adt7463 || data->type == adt7468) && - (data->vid & 0x80)) { + if (data->has_vid5) { /* 6-pin VID (VRM 10) */ vid = vid_from_reg(data->vid & 0x3f, data->vrm); } else { @@ -891,7 +889,6 @@ static ssize_t set_temp_auto_temp_off(struct device *dev, mutex_lock(&data->update_lock); min = TEMP_FROM_REG(data->zone[nr].limit); - data->zone[nr].off_desired = TEMP_TO_REG(val); data->zone[nr].hyst = HYST_TO_REG(min - val); if (nr == 0 || nr == 1) { lm85_write_value(client, LM85_REG_AFAN_HYST1, @@ -934,18 +931,6 @@ static ssize_t set_temp_auto_temp_min(struct device *dev, ((data->zone[nr].range & 0x0f) << 4) | (data->pwm_freq[nr] & 0x07)); -/* Update temp_auto_hyst and temp_auto_off */ - data->zone[nr].hyst = HYST_TO_REG(TEMP_FROM_REG( - data->zone[nr].limit) - TEMP_FROM_REG( - data->zone[nr].off_desired)); - if (nr == 0 || nr == 1) { - lm85_write_value(client, LM85_REG_AFAN_HYST1, - (data->zone[0].hyst << 4) - | data->zone[1].hyst); - } else { - lm85_write_value(client, LM85_REG_AFAN_HYST2, - (data->zone[2].hyst << 4)); - } mutex_unlock(&data->update_lock); return count; } @@ -1084,13 +1069,7 @@ static struct attribute *lm85_attributes[] = { &sensor_dev_attr_pwm1_auto_pwm_min.dev_attr.attr, &sensor_dev_attr_pwm2_auto_pwm_min.dev_attr.attr, &sensor_dev_attr_pwm3_auto_pwm_min.dev_attr.attr, - &sensor_dev_attr_pwm1_auto_pwm_minctl.dev_attr.attr, - &sensor_dev_attr_pwm2_auto_pwm_minctl.dev_attr.attr, - &sensor_dev_attr_pwm3_auto_pwm_minctl.dev_attr.attr, - &sensor_dev_attr_temp1_auto_temp_off.dev_attr.attr, - &sensor_dev_attr_temp2_auto_temp_off.dev_attr.attr, - &sensor_dev_attr_temp3_auto_temp_off.dev_attr.attr, &sensor_dev_attr_temp1_auto_temp_min.dev_attr.attr, &sensor_dev_attr_temp2_auto_temp_min.dev_attr.attr, &sensor_dev_attr_temp3_auto_temp_min.dev_attr.attr, @@ -1111,6 +1090,26 @@ static const struct attribute_group lm85_group = { .attrs = lm85_attributes, }; +static struct attribute *lm85_attributes_minctl[] = { + &sensor_dev_attr_pwm1_auto_pwm_minctl.dev_attr.attr, + &sensor_dev_attr_pwm2_auto_pwm_minctl.dev_attr.attr, + &sensor_dev_attr_pwm3_auto_pwm_minctl.dev_attr.attr, +}; + +static const struct attribute_group lm85_group_minctl = { + .attrs = lm85_attributes_minctl, +}; + +static struct attribute *lm85_attributes_temp_off[] = { + &sensor_dev_attr_temp1_auto_temp_off.dev_attr.attr, + &sensor_dev_attr_temp2_auto_temp_off.dev_attr.attr, + &sensor_dev_attr_temp3_auto_temp_off.dev_attr.attr, +}; + +static const struct attribute_group lm85_group_temp_off = { + .attrs = lm85_attributes_temp_off, +}; + static struct attribute *lm85_attributes_in4[] = { &sensor_dev_attr_in4_input.dev_attr.attr, &sensor_dev_attr_in4_min.dev_attr.attr, @@ -1258,16 +1257,9 @@ static int lm85_detect(struct i2c_client *client, struct i2c_board_info *info) case LM85_VERSTEP_EMC6D103_A1: type_name = "emc6d103"; break; - /* - * Registers apparently missing in EMC6D103S/EMC6D103:A2 - * compared to EMC6D103:A0, EMC6D103:A1, and EMC6D102 - * (according to the data sheets), but used unconditionally - * in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. - * So skip EMC6D103S for now. case LM85_VERSTEP_EMC6D103S: type_name = "emc6d103s"; break; - */ } } else { dev_dbg(&adapter->dev, @@ -1280,6 +1272,19 @@ static int lm85_detect(struct i2c_client *client, struct i2c_board_info *info) return 0; } +static void lm85_remove_files(struct i2c_client *client, struct lm85_data *data) +{ + sysfs_remove_group(&client->dev.kobj, &lm85_group); + if (data->type != emc6d103s) { + sysfs_remove_group(&client->dev.kobj, &lm85_group_minctl); + sysfs_remove_group(&client->dev.kobj, &lm85_group_temp_off); + } + if (!data->has_vid5) + sysfs_remove_group(&client->dev.kobj, &lm85_group_in4); + if (data->type == emc6d100) + sysfs_remove_group(&client->dev.kobj, &lm85_group_in567); +} + static int lm85_probe(struct i2c_client *client, const struct i2c_device_id *id) { @@ -1302,6 +1307,7 @@ static int lm85_probe(struct i2c_client *client, case emc6d100: case emc6d102: case emc6d103: + case emc6d103s: data->freq_map = adm1027_freq_map; break; default: @@ -1319,11 +1325,26 @@ static int lm85_probe(struct i2c_client *client, if (err) goto err_kfree; + /* minctl and temp_off exist on all chips except emc6d103s */ + if (data->type != emc6d103s) { + err = sysfs_create_group(&client->dev.kobj, &lm85_group_minctl); + if (err) + goto err_kfree; + err = sysfs_create_group(&client->dev.kobj, + &lm85_group_temp_off); + if (err) + goto err_kfree; + } + /* The ADT7463/68 have an optional VRM 10 mode where pin 21 is used as a sixth digital VID input rather than an analog input. */ - data->vid = lm85_read_value(client, LM85_REG_VID); - if (!((data->type == adt7463 || data->type == adt7468) && - (data->vid & 0x80))) + if (data->type == adt7463 || data->type == adt7468) { + u8 vid = lm85_read_value(client, LM85_REG_VID); + if (vid & 0x80) + data->has_vid5 = true; + } + + if (!data->has_vid5) if ((err = sysfs_create_group(&client->dev.kobj, &lm85_group_in4))) goto err_remove_files; @@ -1344,10 +1365,7 @@ static int lm85_probe(struct i2c_client *client, /* Error out and cleanup code */ err_remove_files: - sysfs_remove_group(&client->dev.kobj, &lm85_group); - sysfs_remove_group(&client->dev.kobj, &lm85_group_in4); - if (data->type == emc6d100) - sysfs_remove_group(&client->dev.kobj, &lm85_group_in567); + lm85_remove_files(client, data); err_kfree: kfree(data); return err; @@ -1357,10 +1375,7 @@ static int lm85_remove(struct i2c_client *client) { struct lm85_data *data = i2c_get_clientdata(client); hwmon_device_unregister(data->hwmon_dev); - sysfs_remove_group(&client->dev.kobj, &lm85_group); - sysfs_remove_group(&client->dev.kobj, &lm85_group_in4); - if (data->type == emc6d100) - sysfs_remove_group(&client->dev.kobj, &lm85_group_in567); + lm85_remove_files(client, data); kfree(data); return 0; } @@ -1457,11 +1472,8 @@ static struct lm85_data *lm85_update_device(struct device *dev) lm85_read_value(client, LM85_REG_FAN(i)); } - if (!((data->type == adt7463 || data->type == adt7468) && - (data->vid & 0x80))) { - data->in[4] = lm85_read_value(client, - LM85_REG_IN(4)); - } + if (!data->has_vid5) + data->in[4] = lm85_read_value(client, LM85_REG_IN(4)); if (data->type == adt7468) data->cfg5 = lm85_read_value(client, ADT7468_REG_CFG5); @@ -1487,7 +1499,8 @@ static struct lm85_data *lm85_update_device(struct device *dev) /* More alarm bits */ data->alarms |= lm85_read_value(client, EMC6D100_REG_ALARM3) << 16; - } else if (data->type == emc6d102 || data->type == emc6d103) { + } else if (data->type == emc6d102 || data->type == emc6d103 || + data->type == emc6d103s) { /* Have to read LSB bits after the MSB ones because the reading of the MSB bits has frozen the LSBs (backward from the ADM1027). @@ -1528,8 +1541,7 @@ static struct lm85_data *lm85_update_device(struct device *dev) lm85_read_value(client, LM85_REG_FAN_MIN(i)); } - if (!((data->type == adt7463 || data->type == adt7468) && - (data->vid & 0x80))) { + if (!data->has_vid5) { data->in_min[4] = lm85_read_value(client, LM85_REG_IN_MIN(4)); data->in_max[4] = lm85_read_value(client, @@ -1573,17 +1585,19 @@ static struct lm85_data *lm85_update_device(struct device *dev) } } - i = lm85_read_value(client, LM85_REG_AFAN_SPIKE1); - data->autofan[0].min_off = (i & 0x20) != 0; - data->autofan[1].min_off = (i & 0x40) != 0; - data->autofan[2].min_off = (i & 0x80) != 0; + if (data->type != emc6d103s) { + i = lm85_read_value(client, LM85_REG_AFAN_SPIKE1); + data->autofan[0].min_off = (i & 0x20) != 0; + data->autofan[1].min_off = (i & 0x40) != 0; + data->autofan[2].min_off = (i & 0x80) != 0; - i = lm85_read_value(client, LM85_REG_AFAN_HYST1); - data->zone[0].hyst = i >> 4; - data->zone[1].hyst = i & 0x0f; + i = lm85_read_value(client, LM85_REG_AFAN_HYST1); + data->zone[0].hyst = i >> 4; + data->zone[1].hyst = i & 0x0f; - i = lm85_read_value(client, LM85_REG_AFAN_HYST2); - data->zone[2].hyst = i >> 4; + i = lm85_read_value(client, LM85_REG_AFAN_HYST2); + data->zone[2].hyst = i >> 4; + } data->last_config = jiffies; } /* last_config */ diff --git a/drivers/hwmon/ltc4151.c b/drivers/hwmon/ltc4151.c new file mode 100644 index 00000000000..4ac06b75aa6 --- /dev/null +++ b/drivers/hwmon/ltc4151.c @@ -0,0 +1,256 @@ +/* + * Driver for Linear Technology LTC4151 High Voltage I2C Current + * and Voltage Monitor + * + * Copyright (C) 2011 AppearTV AS + * + * Derived from: + * + * Driver for Linear Technology LTC4261 I2C Negative Voltage Hot + * Swap Controller + * Copyright (C) 2010 Ericsson AB. + * + * Datasheet: http://www.linear.com/docs/Datasheet/4151fc.pdf + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> + +/* chip registers */ +#define LTC4151_SENSE_H 0x00 +#define LTC4151_SENSE_L 0x01 +#define LTC4151_VIN_H 0x02 +#define LTC4151_VIN_L 0x03 +#define LTC4151_ADIN_H 0x04 +#define LTC4151_ADIN_L 0x05 + +struct ltc4151_data { + struct device *hwmon_dev; + + struct mutex update_lock; + bool valid; + unsigned long last_updated; /* in jiffies */ + + /* Registers */ + u8 regs[6]; +}; + +static struct ltc4151_data *ltc4151_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct ltc4151_data *data = i2c_get_clientdata(client); + struct ltc4151_data *ret = data; + + mutex_lock(&data->update_lock); + + /* + * The chip's A/D updates 6 times per second + * (Conversion Rate 6 - 9 Hz) + */ + if (time_after(jiffies, data->last_updated + HZ / 6) || !data->valid) { + int i; + + dev_dbg(&client->dev, "Starting ltc4151 update\n"); + + /* Read all registers */ + for (i = 0; i < ARRAY_SIZE(data->regs); i++) { + int val; + + val = i2c_smbus_read_byte_data(client, i); + if (unlikely(val < 0)) { + dev_dbg(dev, + "Failed to read ADC value: error %d\n", + val); + ret = ERR_PTR(val); + goto abort; + } + data->regs[i] = val; + } + data->last_updated = jiffies; + data->valid = 1; + } +abort: + mutex_unlock(&data->update_lock); + return ret; +} + +/* Return the voltage from the given register in mV */ +static int ltc4151_get_value(struct ltc4151_data *data, u8 reg) +{ + u32 val; + + val = (data->regs[reg] << 4) + (data->regs[reg + 1] >> 4); + + switch (reg) { + case LTC4151_ADIN_H: + /* 500uV resolution. Convert to mV. */ + val = val * 500 / 1000; + break; + case LTC4151_SENSE_H: + /* + * 20uV resolution. Convert to current as measured with + * an 1 mOhm sense resistor, in mA. + */ + val = val * 20; + break; + case LTC4151_VIN_H: + /* 25 mV per increment */ + val = val * 25; + break; + default: + /* If we get here, the developer messed up */ + WARN_ON_ONCE(1); + val = 0; + break; + } + + return val; +} + +static ssize_t ltc4151_show_value(struct device *dev, + struct device_attribute *da, char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); + struct ltc4151_data *data = ltc4151_update_device(dev); + int value; + + if (IS_ERR(data)) + return PTR_ERR(data); + + value = ltc4151_get_value(data, attr->index); + return snprintf(buf, PAGE_SIZE, "%d\n", value); +} + +/* + * Input voltages. + */ +static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, \ + ltc4151_show_value, NULL, LTC4151_VIN_H); +static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, \ + ltc4151_show_value, NULL, LTC4151_ADIN_H); + +/* Currents (via sense resistor) */ +static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, \ + ltc4151_show_value, NULL, LTC4151_SENSE_H); + +/* Finally, construct an array of pointers to members of the above objects, + * as required for sysfs_create_group() + */ +static struct attribute *ltc4151_attributes[] = { + &sensor_dev_attr_in1_input.dev_attr.attr, + &sensor_dev_attr_in2_input.dev_attr.attr, + + &sensor_dev_attr_curr1_input.dev_attr.attr, + + NULL, +}; + +static const struct attribute_group ltc4151_group = { + .attrs = ltc4151_attributes, +}; + +static int ltc4151_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adapter = client->adapter; + struct ltc4151_data *data; + int ret; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -ENODEV; + + data = kzalloc(sizeof(*data), GFP_KERNEL); + if (!data) { + ret = -ENOMEM; + goto out_kzalloc; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + + /* Register sysfs hooks */ + ret = sysfs_create_group(&client->dev.kobj, <c4151_group); + if (ret) + goto out_sysfs_create_group; + + data->hwmon_dev = hwmon_device_register(&client->dev); + if (IS_ERR(data->hwmon_dev)) { + ret = PTR_ERR(data->hwmon_dev); + goto out_hwmon_device_register; + } + + return 0; + +out_hwmon_device_register: + sysfs_remove_group(&client->dev.kobj, <c4151_group); +out_sysfs_create_group: + kfree(data); +out_kzalloc: + return ret; +} + +static int ltc4151_remove(struct i2c_client *client) +{ + struct ltc4151_data *data = i2c_get_clientdata(client); + + hwmon_device_unregister(data->hwmon_dev); + sysfs_remove_group(&client->dev.kobj, <c4151_group); + + kfree(data); + + return 0; +} + +static const struct i2c_device_id ltc4151_id[] = { + { "ltc4151", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ltc4151_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver ltc4151_driver = { + .driver = { + .name = "ltc4151", + }, + .probe = ltc4151_probe, + .remove = ltc4151_remove, + .id_table = ltc4151_id, +}; + +static int __init ltc4151_init(void) +{ + return i2c_add_driver(<c4151_driver); +} + +static void __exit ltc4151_exit(void) +{ + i2c_del_driver(<c4151_driver); +} + +MODULE_AUTHOR("Per Dalen <per.dalen@appeartv.com>"); +MODULE_DESCRIPTION("LTC4151 driver"); +MODULE_LICENSE("GPL"); + +module_init(ltc4151_init); +module_exit(ltc4151_exit); diff --git a/drivers/hwmon/max16064.c b/drivers/hwmon/max16064.c new file mode 100644 index 00000000000..1d6d717060d --- /dev/null +++ b/drivers/hwmon/max16064.c @@ -0,0 +1,91 @@ +/* + * Hardware monitoring driver for Maxim MAX16064 + * + * Copyright (c) 2011 Ericsson AB. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/i2c.h> +#include "pmbus.h" + +static struct pmbus_driver_info max16064_info = { + .pages = 4, + .direct[PSC_VOLTAGE_IN] = true, + .direct[PSC_VOLTAGE_OUT] = true, + .direct[PSC_TEMPERATURE] = true, + .m[PSC_VOLTAGE_IN] = 19995, + .b[PSC_VOLTAGE_IN] = 0, + .R[PSC_VOLTAGE_IN] = -1, + .m[PSC_VOLTAGE_OUT] = 19995, + .b[PSC_VOLTAGE_OUT] = 0, + .R[PSC_VOLTAGE_OUT] = -1, + .m[PSC_TEMPERATURE] = -7612, + .b[PSC_TEMPERATURE] = 335, + .R[PSC_TEMPERATURE] = -3, + .func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_TEMP + | PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_STATUS_TEMP, + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT, + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT, + .func[3] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT, +}; + +static int max16064_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + return pmbus_do_probe(client, id, &max16064_info); +} + +static int max16064_remove(struct i2c_client *client) +{ + return pmbus_do_remove(client); +} + +static const struct i2c_device_id max16064_id[] = { + {"max16064", 0}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, max16064_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver max16064_driver = { + .driver = { + .name = "max16064", + }, + .probe = max16064_probe, + .remove = max16064_remove, + .id_table = max16064_id, +}; + +static int __init max16064_init(void) +{ + return i2c_add_driver(&max16064_driver); +} + +static void __exit max16064_exit(void) +{ + i2c_del_driver(&max16064_driver); +} + +MODULE_AUTHOR("Guenter Roeck"); +MODULE_DESCRIPTION("PMBus driver for Maxim MAX16064"); +MODULE_LICENSE("GPL"); +module_init(max16064_init); +module_exit(max16064_exit); diff --git a/drivers/hwmon/max34440.c b/drivers/hwmon/max34440.c new file mode 100644 index 00000000000..992b701b4c5 --- /dev/null +++ b/drivers/hwmon/max34440.c @@ -0,0 +1,199 @@ +/* + * Hardware monitoring driver for Maxim MAX34440/MAX34441 + * + * Copyright (c) 2011 Ericsson AB. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/i2c.h> +#include "pmbus.h" + +enum chips { max34440, max34441 }; + +#define MAX34440_STATUS_OC_WARN (1 << 0) +#define MAX34440_STATUS_OC_FAULT (1 << 1) +#define MAX34440_STATUS_OT_FAULT (1 << 5) +#define MAX34440_STATUS_OT_WARN (1 << 6) + +static int max34440_get_status(struct i2c_client *client, int page, int reg) +{ + int ret; + int mfg_status; + + ret = pmbus_set_page(client, page); + if (ret < 0) + return ret; + + switch (reg) { + case PMBUS_STATUS_IOUT: + mfg_status = pmbus_read_word_data(client, 0, + PMBUS_STATUS_MFR_SPECIFIC); + if (mfg_status < 0) + return mfg_status; + if (mfg_status & MAX34440_STATUS_OC_WARN) + ret |= PB_IOUT_OC_WARNING; + if (mfg_status & MAX34440_STATUS_OC_FAULT) + ret |= PB_IOUT_OC_FAULT; + break; + case PMBUS_STATUS_TEMPERATURE: + mfg_status = pmbus_read_word_data(client, 0, + PMBUS_STATUS_MFR_SPECIFIC); + if (mfg_status < 0) + return mfg_status; + if (mfg_status & MAX34440_STATUS_OT_WARN) + ret |= PB_TEMP_OT_WARNING; + if (mfg_status & MAX34440_STATUS_OT_FAULT) + ret |= PB_TEMP_OT_FAULT; + break; + default: + ret = -ENODATA; + break; + } + return ret; +} + +static struct pmbus_driver_info max34440_info[] = { + [max34440] = { + .pages = 14, + .direct[PSC_VOLTAGE_IN] = true, + .direct[PSC_VOLTAGE_OUT] = true, + .direct[PSC_TEMPERATURE] = true, + .direct[PSC_CURRENT_OUT] = true, + .m[PSC_VOLTAGE_IN] = 1, + .b[PSC_VOLTAGE_IN] = 0, + .R[PSC_VOLTAGE_IN] = 3, /* R = 0 in datasheet reflects mV */ + .m[PSC_VOLTAGE_OUT] = 1, + .b[PSC_VOLTAGE_OUT] = 0, + .R[PSC_VOLTAGE_OUT] = 3, /* R = 0 in datasheet reflects mV */ + .m[PSC_CURRENT_OUT] = 1, + .b[PSC_CURRENT_OUT] = 0, + .R[PSC_CURRENT_OUT] = 3, /* R = 0 in datasheet reflects mA */ + .m[PSC_TEMPERATURE] = 1, + .b[PSC_TEMPERATURE] = 0, + .R[PSC_TEMPERATURE] = 2, + .func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[3] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[4] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[5] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[6] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[7] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[8] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[9] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[10] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[11] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[12] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[13] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .get_status = max34440_get_status, + }, + [max34441] = { + .pages = 12, + .direct[PSC_VOLTAGE_IN] = true, + .direct[PSC_VOLTAGE_OUT] = true, + .direct[PSC_TEMPERATURE] = true, + .direct[PSC_CURRENT_OUT] = true, + .direct[PSC_FAN] = true, + .m[PSC_VOLTAGE_IN] = 1, + .b[PSC_VOLTAGE_IN] = 0, + .R[PSC_VOLTAGE_IN] = 3, + .m[PSC_VOLTAGE_OUT] = 1, + .b[PSC_VOLTAGE_OUT] = 0, + .R[PSC_VOLTAGE_OUT] = 3, + .m[PSC_CURRENT_OUT] = 1, + .b[PSC_CURRENT_OUT] = 0, + .R[PSC_CURRENT_OUT] = 3, + .m[PSC_TEMPERATURE] = 1, + .b[PSC_TEMPERATURE] = 0, + .R[PSC_TEMPERATURE] = 2, + .m[PSC_FAN] = 1, + .b[PSC_FAN] = 0, + .R[PSC_FAN] = 0, + .func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[3] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[4] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT, + .func[5] = PMBUS_HAVE_FAN12 | PMBUS_HAVE_STATUS_FAN12, + .func[6] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[7] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[8] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[9] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[10] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .func[11] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP, + .get_status = max34440_get_status, + }, +}; + +static int max34440_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + return pmbus_do_probe(client, id, &max34440_info[id->driver_data]); +} + +static int max34440_remove(struct i2c_client *client) +{ + return pmbus_do_remove(client); +} + +static const struct i2c_device_id max34440_id[] = { + {"max34440", max34440}, + {"max34441", max34441}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, max34440_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver max34440_driver = { + .driver = { + .name = "max34440", + }, + .probe = max34440_probe, + .remove = max34440_remove, + .id_table = max34440_id, +}; + +static int __init max34440_init(void) +{ + return i2c_add_driver(&max34440_driver); +} + +static void __exit max34440_exit(void) +{ + i2c_del_driver(&max34440_driver); +} + +MODULE_AUTHOR("Guenter Roeck"); +MODULE_DESCRIPTION("PMBus driver for Maxim MAX34440/MAX34441"); +MODULE_LICENSE("GPL"); +module_init(max34440_init); +module_exit(max34440_exit); diff --git a/drivers/hwmon/max6639.c b/drivers/hwmon/max6639.c new file mode 100644 index 00000000000..f20d9978ee7 --- /dev/null +++ b/drivers/hwmon/max6639.c @@ -0,0 +1,653 @@ +/* + * max6639.c - Support for Maxim MAX6639 + * + * 2-Channel Temperature Monitor with Dual PWM Fan-Speed Controller + * + * Copyright (C) 2010, 2011 Roland Stigge <stigge@antcom.de> + * + * based on the initial MAX6639 support from semptian.net + * by He Changqing <hechangqing@semptian.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/jiffies.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/err.h> +#include <linux/mutex.h> +#include <linux/i2c/max6639.h> + +/* Addresses to scan */ +static unsigned short normal_i2c[] = { 0x2c, 0x2e, 0x2f, I2C_CLIENT_END }; + +/* The MAX6639 registers, valid channel numbers: 0, 1 */ +#define MAX6639_REG_TEMP(ch) (0x00 + (ch)) +#define MAX6639_REG_STATUS 0x02 +#define MAX6639_REG_OUTPUT_MASK 0x03 +#define MAX6639_REG_GCONFIG 0x04 +#define MAX6639_REG_TEMP_EXT(ch) (0x05 + (ch)) +#define MAX6639_REG_ALERT_LIMIT(ch) (0x08 + (ch)) +#define MAX6639_REG_OT_LIMIT(ch) (0x0A + (ch)) +#define MAX6639_REG_THERM_LIMIT(ch) (0x0C + (ch)) +#define MAX6639_REG_FAN_CONFIG1(ch) (0x10 + (ch) * 4) +#define MAX6639_REG_FAN_CONFIG2a(ch) (0x11 + (ch) * 4) +#define MAX6639_REG_FAN_CONFIG2b(ch) (0x12 + (ch) * 4) +#define MAX6639_REG_FAN_CONFIG3(ch) (0x13 + (ch) * 4) +#define MAX6639_REG_FAN_CNT(ch) (0x20 + (ch)) +#define MAX6639_REG_TARGET_CNT(ch) (0x22 + (ch)) +#define MAX6639_REG_FAN_PPR(ch) (0x24 + (ch)) +#define MAX6639_REG_TARGTDUTY(ch) (0x26 + (ch)) +#define MAX6639_REG_FAN_START_TEMP(ch) (0x28 + (ch)) +#define MAX6639_REG_DEVID 0x3D +#define MAX6639_REG_MANUID 0x3E +#define MAX6639_REG_DEVREV 0x3F + +/* Register bits */ +#define MAX6639_GCONFIG_STANDBY 0x80 +#define MAX6639_GCONFIG_POR 0x40 +#define MAX6639_GCONFIG_DISABLE_TIMEOUT 0x20 +#define MAX6639_GCONFIG_CH2_LOCAL 0x10 +#define MAX6639_GCONFIG_PWM_FREQ_HI 0x08 + +#define MAX6639_FAN_CONFIG1_PWM 0x80 + +#define MAX6639_FAN_CONFIG3_THERM_FULL_SPEED 0x40 + +static const int rpm_ranges[] = { 2000, 4000, 8000, 16000 }; + +#define FAN_FROM_REG(val, div, rpm_range) ((val) == 0 ? -1 : \ + (val) == 255 ? 0 : (rpm_ranges[rpm_range] * 30) / ((div + 1) * (val))) +#define TEMP_LIMIT_TO_REG(val) SENSORS_LIMIT((val) / 1000, 0, 255) + +/* + * Client data (each client gets its own) + */ +struct max6639_data { + struct device *hwmon_dev; + struct mutex update_lock; + char valid; /* !=0 if following fields are valid */ + unsigned long last_updated; /* In jiffies */ + + /* Register values sampled regularly */ + u16 temp[2]; /* Temperature, in 1/8 C, 0..255 C */ + bool temp_fault[2]; /* Detected temperature diode failure */ + u8 fan[2]; /* Register value: TACH count for fans >=30 */ + u8 status; /* Detected channel alarms and fan failures */ + + /* Register values only written to */ + u8 pwm[2]; /* Register value: Duty cycle 0..120 */ + u8 temp_therm[2]; /* THERM Temperature, 0..255 C (->_max) */ + u8 temp_alert[2]; /* ALERT Temperature, 0..255 C (->_crit) */ + u8 temp_ot[2]; /* OT Temperature, 0..255 C (->_emergency) */ + + /* Register values initialized only once */ + u8 ppr; /* Pulses per rotation 0..3 for 1..4 ppr */ + u8 rpm_range; /* Index in above rpm_ranges table */ +}; + +static struct max6639_data *max6639_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct max6639_data *data = i2c_get_clientdata(client); + struct max6639_data *ret = data; + int i; + int status_reg; + + mutex_lock(&data->update_lock); + + if (time_after(jiffies, data->last_updated + 2 * HZ) || !data->valid) { + int res; + + dev_dbg(&client->dev, "Starting max6639 update\n"); + + status_reg = i2c_smbus_read_byte_data(client, + MAX6639_REG_STATUS); + if (status_reg < 0) { + ret = ERR_PTR(status_reg); + goto abort; + } + + data->status = status_reg; + + for (i = 0; i < 2; i++) { + res = i2c_smbus_read_byte_data(client, + MAX6639_REG_FAN_CNT(i)); + if (res < 0) { + ret = ERR_PTR(res); + goto abort; + } + data->fan[i] = res; + + res = i2c_smbus_read_byte_data(client, + MAX6639_REG_TEMP_EXT(i)); + if (res < 0) { + ret = ERR_PTR(res); + goto abort; + } + data->temp[i] = res >> 5; + data->temp_fault[i] = res & 0x01; + + res = i2c_smbus_read_byte_data(client, + MAX6639_REG_TEMP(i)); + if (res < 0) { + ret = ERR_PTR(res); + goto abort; + } + data->temp[i] |= res << 3; + } + + data->last_updated = jiffies; + data->valid = 1; + } +abort: + mutex_unlock(&data->update_lock); + + return ret; +} + +static ssize_t show_temp_input(struct device *dev, + struct device_attribute *dev_attr, char *buf) +{ + long temp; + struct max6639_data *data = max6639_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + + if (IS_ERR(data)) + return PTR_ERR(data); + + temp = data->temp[attr->index] * 125; + return sprintf(buf, "%ld\n", temp); +} + +static ssize_t show_temp_fault(struct device *dev, + struct device_attribute *dev_attr, char *buf) +{ + struct max6639_data *data = max6639_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + + if (IS_ERR(data)) + return PTR_ERR(data); + + return sprintf(buf, "%d\n", data->temp_fault[attr->index]); +} + +static ssize_t show_temp_max(struct device *dev, + struct device_attribute *dev_attr, char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct max6639_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + + return sprintf(buf, "%d\n", (data->temp_therm[attr->index] * 1000)); +} + +static ssize_t set_temp_max(struct device *dev, + struct device_attribute *dev_attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct max6639_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + unsigned long val; + int res; + + res = strict_strtoul(buf, 10, &val); + if (res) + return res; + + mutex_lock(&data->update_lock); + data->temp_therm[attr->index] = TEMP_LIMIT_TO_REG(val); + i2c_smbus_write_byte_data(client, + MAX6639_REG_THERM_LIMIT(attr->index), + data->temp_therm[attr->index]); + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t show_temp_crit(struct device *dev, + struct device_attribute *dev_attr, char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct max6639_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + + return sprintf(buf, "%d\n", (data->temp_alert[attr->index] * 1000)); +} + +static ssize_t set_temp_crit(struct device *dev, + struct device_attribute *dev_attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct max6639_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + unsigned long val; + int res; + + res = strict_strtoul(buf, 10, &val); + if (res) + return res; + + mutex_lock(&data->update_lock); + data->temp_alert[attr->index] = TEMP_LIMIT_TO_REG(val); + i2c_smbus_write_byte_data(client, + MAX6639_REG_ALERT_LIMIT(attr->index), + data->temp_alert[attr->index]); + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t show_temp_emergency(struct device *dev, + struct device_attribute *dev_attr, + char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct max6639_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + + return sprintf(buf, "%d\n", (data->temp_ot[attr->index] * 1000)); +} + +static ssize_t set_temp_emergency(struct device *dev, + struct device_attribute *dev_attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct max6639_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + unsigned long val; + int res; + + res = strict_strtoul(buf, 10, &val); + if (res) + return res; + + mutex_lock(&data->update_lock); + data->temp_ot[attr->index] = TEMP_LIMIT_TO_REG(val); + i2c_smbus_write_byte_data(client, + MAX6639_REG_OT_LIMIT(attr->index), + data->temp_ot[attr->index]); + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t show_pwm(struct device *dev, + struct device_attribute *dev_attr, char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct max6639_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + + return sprintf(buf, "%d\n", data->pwm[attr->index] * 255 / 120); +} + +static ssize_t set_pwm(struct device *dev, + struct device_attribute *dev_attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct max6639_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + unsigned long val; + int res; + + res = strict_strtoul(buf, 10, &val); + if (res) + return res; + + val = SENSORS_LIMIT(val, 0, 255); + + mutex_lock(&data->update_lock); + data->pwm[attr->index] = (u8)(val * 120 / 255); + i2c_smbus_write_byte_data(client, + MAX6639_REG_TARGTDUTY(attr->index), + data->pwm[attr->index]); + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t show_fan_input(struct device *dev, + struct device_attribute *dev_attr, char *buf) +{ + struct max6639_data *data = max6639_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + + if (IS_ERR(data)) + return PTR_ERR(data); + + return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[attr->index], + data->ppr, data->rpm_range)); +} + +static ssize_t show_alarm(struct device *dev, + struct device_attribute *dev_attr, char *buf) +{ + struct max6639_data *data = max6639_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); + + if (IS_ERR(data)) + return PTR_ERR(data); + + return sprintf(buf, "%d\n", !!(data->status & (1 << attr->index))); +} + +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_input, NULL, 0); +static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp_input, NULL, 1); +static SENSOR_DEVICE_ATTR(temp1_fault, S_IRUGO, show_temp_fault, NULL, 0); +static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_temp_fault, NULL, 1); +static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp_max, + set_temp_max, 0); +static SENSOR_DEVICE_ATTR(temp2_max, S_IWUSR | S_IRUGO, show_temp_max, + set_temp_max, 1); +static SENSOR_DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO, show_temp_crit, + set_temp_crit, 0); +static SENSOR_DEVICE_ATTR(temp2_crit, S_IWUSR | S_IRUGO, show_temp_crit, + set_temp_crit, 1); +static SENSOR_DEVICE_ATTR(temp1_emergency, S_IWUSR | S_IRUGO, + show_temp_emergency, set_temp_emergency, 0); +static SENSOR_DEVICE_ATTR(temp2_emergency, S_IWUSR | S_IRUGO, + show_temp_emergency, set_temp_emergency, 1); +static SENSOR_DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm, set_pwm, 0); +static SENSOR_DEVICE_ATTR(pwm2, S_IWUSR | S_IRUGO, show_pwm, set_pwm, 1); +static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_fan_input, NULL, 0); +static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, show_fan_input, NULL, 1); +static SENSOR_DEVICE_ATTR(fan1_fault, S_IRUGO, show_alarm, NULL, 1); +static SENSOR_DEVICE_ATTR(fan2_fault, S_IRUGO, show_alarm, NULL, 0); +static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 3); +static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_alarm, NULL, 2); +static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 7); +static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, 6); +static SENSOR_DEVICE_ATTR(temp1_emergency_alarm, S_IRUGO, show_alarm, NULL, 5); +static SENSOR_DEVICE_ATTR(temp2_emergency_alarm, S_IRUGO, show_alarm, NULL, 4); + + +static struct attribute *max6639_attributes[] = { + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_temp2_input.dev_attr.attr, + &sensor_dev_attr_temp1_fault.dev_attr.attr, + &sensor_dev_attr_temp2_fault.dev_attr.attr, + &sensor_dev_attr_temp1_max.dev_attr.attr, + &sensor_dev_attr_temp2_max.dev_attr.attr, + &sensor_dev_attr_temp1_crit.dev_attr.attr, + &sensor_dev_attr_temp2_crit.dev_attr.attr, + &sensor_dev_attr_temp1_emergency.dev_attr.attr, + &sensor_dev_attr_temp2_emergency.dev_attr.attr, + &sensor_dev_attr_pwm1.dev_attr.attr, + &sensor_dev_attr_pwm2.dev_attr.attr, + &sensor_dev_attr_fan1_input.dev_attr.attr, + &sensor_dev_attr_fan2_input.dev_attr.attr, + &sensor_dev_attr_fan1_fault.dev_attr.attr, + &sensor_dev_attr_fan2_fault.dev_attr.attr, + &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_max_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_crit_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_emergency_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_emergency_alarm.dev_attr.attr, + NULL +}; + +static const struct attribute_group max6639_group = { + .attrs = max6639_attributes, +}; + +/* + * returns respective index in rpm_ranges table + * 1 by default on invalid range + */ +static int rpm_range_to_reg(int range) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(rpm_ranges); i++) { + if (rpm_ranges[i] == range) + return i; + } + + return 1; /* default: 4000 RPM */ +} + +static int max6639_init_client(struct i2c_client *client) +{ + struct max6639_data *data = i2c_get_clientdata(client); + struct max6639_platform_data *max6639_info = + client->dev.platform_data; + int i = 0; + int rpm_range = 1; /* default: 4000 RPM */ + int err = 0; + + /* Reset chip to default values, see below for GCONFIG setup */ + err = i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG, + MAX6639_GCONFIG_POR); + if (err) + goto exit; + + /* Fans pulse per revolution is 2 by default */ + if (max6639_info && max6639_info->ppr > 0 && + max6639_info->ppr < 5) + data->ppr = max6639_info->ppr; + else + data->ppr = 2; + data->ppr -= 1; + err = i2c_smbus_write_byte_data(client, + MAX6639_REG_FAN_PPR(i), + data->ppr << 5); + if (err) + goto exit; + + if (max6639_info) + rpm_range = rpm_range_to_reg(max6639_info->rpm_range); + data->rpm_range = rpm_range; + + for (i = 0; i < 2; i++) { + + /* Fans config PWM, RPM */ + err = i2c_smbus_write_byte_data(client, + MAX6639_REG_FAN_CONFIG1(i), + MAX6639_FAN_CONFIG1_PWM | rpm_range); + if (err) + goto exit; + + /* Fans PWM polarity high by default */ + if (max6639_info && max6639_info->pwm_polarity == 0) + err = i2c_smbus_write_byte_data(client, + MAX6639_REG_FAN_CONFIG2a(i), 0x00); + else + err = i2c_smbus_write_byte_data(client, + MAX6639_REG_FAN_CONFIG2a(i), 0x02); + if (err) + goto exit; + + /* + * /THERM full speed enable, + * PWM frequency 25kHz, see also GCONFIG below + */ + err = i2c_smbus_write_byte_data(client, + MAX6639_REG_FAN_CONFIG3(i), + MAX6639_FAN_CONFIG3_THERM_FULL_SPEED | 0x03); + if (err) + goto exit; + + /* Max. temp. 80C/90C/100C */ + data->temp_therm[i] = 80; + data->temp_alert[i] = 90; + data->temp_ot[i] = 100; + err = i2c_smbus_write_byte_data(client, + MAX6639_REG_THERM_LIMIT(i), + data->temp_therm[i]); + if (err) + goto exit; + err = i2c_smbus_write_byte_data(client, + MAX6639_REG_ALERT_LIMIT(i), + data->temp_alert[i]); + if (err) + goto exit; + err = i2c_smbus_write_byte_data(client, + MAX6639_REG_OT_LIMIT(i), data->temp_ot[i]); + if (err) + goto exit; + + /* PWM 120/120 (i.e. 100%) */ + data->pwm[i] = 120; + err = i2c_smbus_write_byte_data(client, + MAX6639_REG_TARGTDUTY(i), data->pwm[i]); + if (err) + goto exit; + } + /* Start monitoring */ + err = i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG, + MAX6639_GCONFIG_DISABLE_TIMEOUT | MAX6639_GCONFIG_CH2_LOCAL | + MAX6639_GCONFIG_PWM_FREQ_HI); +exit: + return err; +} + +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int max6639_detect(struct i2c_client *client, + struct i2c_board_info *info) +{ + struct i2c_adapter *adapter = client->adapter; + int dev_id, manu_id; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -ENODEV; + + /* Actual detection via device and manufacturer ID */ + dev_id = i2c_smbus_read_byte_data(client, MAX6639_REG_DEVID); + manu_id = i2c_smbus_read_byte_data(client, MAX6639_REG_MANUID); + if (dev_id != 0x58 || manu_id != 0x4D) + return -ENODEV; + + strlcpy(info->type, "max6639", I2C_NAME_SIZE); + + return 0; +} + +static int max6639_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct max6639_data *data; + int err; + + data = kzalloc(sizeof(struct max6639_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + + /* Initialize the max6639 chip */ + err = max6639_init_client(client); + if (err < 0) + goto error_free; + + /* Register sysfs hooks */ + err = sysfs_create_group(&client->dev.kobj, &max6639_group); + if (err) + goto error_free; + + data->hwmon_dev = hwmon_device_register(&client->dev); + if (IS_ERR(data->hwmon_dev)) { + err = PTR_ERR(data->hwmon_dev); + goto error_remove; + } + + dev_info(&client->dev, "temperature sensor and fan control found\n"); + + return 0; + +error_remove: + sysfs_remove_group(&client->dev.kobj, &max6639_group); +error_free: + kfree(data); +exit: + return err; +} + +static int max6639_remove(struct i2c_client *client) +{ + struct max6639_data *data = i2c_get_clientdata(client); + + hwmon_device_unregister(data->hwmon_dev); + sysfs_remove_group(&client->dev.kobj, &max6639_group); + + kfree(data); + return 0; +} + +static int max6639_suspend(struct i2c_client *client, pm_message_t mesg) +{ + int data = i2c_smbus_read_byte_data(client, MAX6639_REG_GCONFIG); + if (data < 0) + return data; + + return i2c_smbus_write_byte_data(client, + MAX6639_REG_GCONFIG, data | MAX6639_GCONFIG_STANDBY); +} + +static int max6639_resume(struct i2c_client *client) +{ + int data = i2c_smbus_read_byte_data(client, MAX6639_REG_GCONFIG); + if (data < 0) + return data; + + return i2c_smbus_write_byte_data(client, + MAX6639_REG_GCONFIG, data & ~MAX6639_GCONFIG_STANDBY); +} + +static const struct i2c_device_id max6639_id[] = { + {"max6639", 0}, + { } +}; + +MODULE_DEVICE_TABLE(i2c, max6639_id); + +static struct i2c_driver max6639_driver = { + .class = I2C_CLASS_HWMON, + .driver = { + .name = "max6639", + }, + .probe = max6639_probe, + .remove = max6639_remove, + .suspend = max6639_suspend, + .resume = max6639_resume, + .id_table = max6639_id, + .detect = max6639_detect, + .address_list = normal_i2c, +}; + +static int __init max6639_init(void) +{ + return i2c_add_driver(&max6639_driver); +} + +static void __exit max6639_exit(void) +{ + i2c_del_driver(&max6639_driver); +} + +MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>"); +MODULE_DESCRIPTION("max6639 driver"); +MODULE_LICENSE("GPL"); + +module_init(max6639_init); +module_exit(max6639_exit); diff --git a/drivers/hwmon/max8688.c b/drivers/hwmon/max8688.c new file mode 100644 index 00000000000..8ebfef2ecf2 --- /dev/null +++ b/drivers/hwmon/max8688.c @@ -0,0 +1,158 @@ +/* + * Hardware monitoring driver for Maxim MAX8688 + * + * Copyright (c) 2011 Ericsson AB. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/i2c.h> +#include "pmbus.h" + +#define MAX8688_MFG_STATUS 0xd8 + +#define MAX8688_STATUS_OC_FAULT (1 << 4) +#define MAX8688_STATUS_OV_FAULT (1 << 5) +#define MAX8688_STATUS_OV_WARNING (1 << 8) +#define MAX8688_STATUS_UV_FAULT (1 << 9) +#define MAX8688_STATUS_UV_WARNING (1 << 10) +#define MAX8688_STATUS_UC_FAULT (1 << 11) +#define MAX8688_STATUS_OC_WARNING (1 << 12) +#define MAX8688_STATUS_OT_FAULT (1 << 13) +#define MAX8688_STATUS_OT_WARNING (1 << 14) + +static int max8688_get_status(struct i2c_client *client, int page, int reg) +{ + int ret = 0; + int mfg_status; + + if (page) + return -EINVAL; + + switch (reg) { + case PMBUS_STATUS_VOUT: + mfg_status = pmbus_read_word_data(client, 0, + MAX8688_MFG_STATUS); + if (mfg_status < 0) + return mfg_status; + if (mfg_status & MAX8688_STATUS_UV_WARNING) + ret |= PB_VOLTAGE_UV_WARNING; + if (mfg_status & MAX8688_STATUS_UV_FAULT) + ret |= PB_VOLTAGE_UV_FAULT; + if (mfg_status & MAX8688_STATUS_OV_WARNING) + ret |= PB_VOLTAGE_OV_WARNING; + if (mfg_status & MAX8688_STATUS_OV_FAULT) + ret |= PB_VOLTAGE_OV_FAULT; + break; + case PMBUS_STATUS_IOUT: + mfg_status = pmbus_read_word_data(client, 0, + MAX8688_MFG_STATUS); + if (mfg_status < 0) + return mfg_status; + if (mfg_status & MAX8688_STATUS_UC_FAULT) + ret |= PB_IOUT_UC_FAULT; + if (mfg_status & MAX8688_STATUS_OC_WARNING) + ret |= PB_IOUT_OC_WARNING; + if (mfg_status & MAX8688_STATUS_OC_FAULT) + ret |= PB_IOUT_OC_FAULT; + break; + case PMBUS_STATUS_TEMPERATURE: + mfg_status = pmbus_read_word_data(client, 0, + MAX8688_MFG_STATUS); + if (mfg_status < 0) + return mfg_status; + if (mfg_status & MAX8688_STATUS_OT_WARNING) + ret |= PB_TEMP_OT_WARNING; + if (mfg_status & MAX8688_STATUS_OT_FAULT) + ret |= PB_TEMP_OT_FAULT; + break; + default: + ret = -ENODATA; + break; + } + return ret; +} + +static struct pmbus_driver_info max8688_info = { + .pages = 1, + .direct[PSC_VOLTAGE_IN] = true, + .direct[PSC_VOLTAGE_OUT] = true, + .direct[PSC_TEMPERATURE] = true, + .direct[PSC_CURRENT_OUT] = true, + .m[PSC_VOLTAGE_IN] = 19995, + .b[PSC_VOLTAGE_IN] = 0, + .R[PSC_VOLTAGE_IN] = -1, + .m[PSC_VOLTAGE_OUT] = 19995, + .b[PSC_VOLTAGE_OUT] = 0, + .R[PSC_VOLTAGE_OUT] = -1, + .m[PSC_CURRENT_OUT] = 23109, + .b[PSC_CURRENT_OUT] = 0, + .R[PSC_CURRENT_OUT] = -2, + .m[PSC_TEMPERATURE] = -7612, + .b[PSC_TEMPERATURE] = 335, + .R[PSC_TEMPERATURE] = -3, + .func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_IOUT | PMBUS_HAVE_TEMP + | PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_STATUS_IOUT + | PMBUS_HAVE_STATUS_TEMP, + .get_status = max8688_get_status, +}; + +static int max8688_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + return pmbus_do_probe(client, id, &max8688_info); +} + +static int max8688_remove(struct i2c_client *client) +{ + return pmbus_do_remove(client); +} + +static const struct i2c_device_id max8688_id[] = { + {"max8688", 0}, + { } +}; + +MODULE_DEVICE_TABLE(i2c, max8688_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver max8688_driver = { + .driver = { + .name = "max8688", + }, + .probe = max8688_probe, + .remove = max8688_remove, + .id_table = max8688_id, +}; + +static int __init max8688_init(void) +{ + return i2c_add_driver(&max8688_driver); +} + +static void __exit max8688_exit(void) +{ + i2c_del_driver(&max8688_driver); +} + +MODULE_AUTHOR("Guenter Roeck"); +MODULE_DESCRIPTION("PMBus driver for Maxim MAX8688"); +MODULE_LICENSE("GPL"); +module_init(max8688_init); +module_exit(max8688_exit); diff --git a/drivers/hwmon/pmbus.c b/drivers/hwmon/pmbus.c new file mode 100644 index 00000000000..98e2e28899e --- /dev/null +++ b/drivers/hwmon/pmbus.c @@ -0,0 +1,203 @@ +/* + * Hardware monitoring driver for PMBus devices + * + * Copyright (c) 2010, 2011 Ericsson AB. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/mutex.h> +#include <linux/i2c.h> +#include "pmbus.h" + +/* + * Find sensor groups and status registers on each page. + */ +static void pmbus_find_sensor_groups(struct i2c_client *client, + struct pmbus_driver_info *info) +{ + int page; + + /* Sensors detected on page 0 only */ + if (pmbus_check_word_register(client, 0, PMBUS_READ_VIN)) + info->func[0] |= PMBUS_HAVE_VIN; + if (pmbus_check_word_register(client, 0, PMBUS_READ_VCAP)) + info->func[0] |= PMBUS_HAVE_VCAP; + if (pmbus_check_word_register(client, 0, PMBUS_READ_IIN)) + info->func[0] |= PMBUS_HAVE_IIN; + if (pmbus_check_word_register(client, 0, PMBUS_READ_PIN)) + info->func[0] |= PMBUS_HAVE_PIN; + if (info->func[0] + && pmbus_check_byte_register(client, 0, PMBUS_STATUS_INPUT)) + info->func[0] |= PMBUS_HAVE_STATUS_INPUT; + if (pmbus_check_word_register(client, 0, PMBUS_READ_FAN_SPEED_1)) { + info->func[0] |= PMBUS_HAVE_FAN12; + if (pmbus_check_byte_register(client, 0, PMBUS_STATUS_FAN_12)) + info->func[0] |= PMBUS_HAVE_STATUS_FAN12; + } + if (pmbus_check_word_register(client, 0, PMBUS_READ_FAN_SPEED_3)) { + info->func[0] |= PMBUS_HAVE_FAN34; + if (pmbus_check_byte_register(client, 0, PMBUS_STATUS_FAN_34)) + info->func[0] |= PMBUS_HAVE_STATUS_FAN34; + } + if (pmbus_check_word_register(client, 0, PMBUS_READ_TEMPERATURE_1)) { + info->func[0] |= PMBUS_HAVE_TEMP; + if (pmbus_check_byte_register(client, 0, + PMBUS_STATUS_TEMPERATURE)) + info->func[0] |= PMBUS_HAVE_STATUS_TEMP; + } + + /* Sensors detected on all pages */ + for (page = 0; page < info->pages; page++) { + if (pmbus_check_word_register(client, page, PMBUS_READ_VOUT)) { + info->func[page] |= PMBUS_HAVE_VOUT; + if (pmbus_check_byte_register(client, page, + PMBUS_STATUS_VOUT)) + info->func[page] |= PMBUS_HAVE_STATUS_VOUT; + } + if (pmbus_check_word_register(client, page, PMBUS_READ_IOUT)) { + info->func[page] |= PMBUS_HAVE_IOUT; + if (pmbus_check_byte_register(client, 0, + PMBUS_STATUS_IOUT)) + info->func[page] |= PMBUS_HAVE_STATUS_IOUT; + } + if (pmbus_check_word_register(client, page, PMBUS_READ_POUT)) + info->func[page] |= PMBUS_HAVE_POUT; + } +} + +/* + * Identify chip parameters. + */ +static int pmbus_identify(struct i2c_client *client, + struct pmbus_driver_info *info) +{ + if (!info->pages) { + /* + * Check if the PAGE command is supported. If it is, + * keep setting the page number until it fails or until the + * maximum number of pages has been reached. Assume that + * this is the number of pages supported by the chip. + */ + if (pmbus_check_byte_register(client, 0, PMBUS_PAGE)) { + int page; + + for (page = 1; page < PMBUS_PAGES; page++) { + if (pmbus_set_page(client, page) < 0) + break; + } + pmbus_set_page(client, 0); + info->pages = page; + } else { + info->pages = 1; + } + } + + /* + * We should check if the COEFFICIENTS register is supported. + * If it is, and the chip is configured for direct mode, we can read + * the coefficients from the chip, one set per group of sensor + * registers. + * + * To do this, we will need access to a chip which actually supports the + * COEFFICIENTS command, since the command is too complex to implement + * without testing it. + */ + + /* Try to find sensor groups */ + pmbus_find_sensor_groups(client, info); + + return 0; +} + +static int pmbus_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct pmbus_driver_info *info; + int ret; + + info = kzalloc(sizeof(struct pmbus_driver_info), GFP_KERNEL); + if (!info) + return -ENOMEM; + + info->pages = id->driver_data; + info->identify = pmbus_identify; + + ret = pmbus_do_probe(client, id, info); + if (ret < 0) + goto out; + return 0; + +out: + kfree(info); + return ret; +} + +static int pmbus_remove(struct i2c_client *client) +{ + int ret; + const struct pmbus_driver_info *info; + + info = pmbus_get_driver_info(client); + ret = pmbus_do_remove(client); + kfree(info); + return ret; +} + +/* + * Use driver_data to set the number of pages supported by the chip. + */ +static const struct i2c_device_id pmbus_id[] = { + {"bmr450", 1}, + {"bmr451", 1}, + {"bmr453", 1}, + {"bmr454", 1}, + {"ltc2978", 8}, + {"pmbus", 0}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, pmbus_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver pmbus_driver = { + .driver = { + .name = "pmbus", + }, + .probe = pmbus_probe, + .remove = pmbus_remove, + .id_table = pmbus_id, +}; + +static int __init pmbus_init(void) +{ + return i2c_add_driver(&pmbus_driver); +} + +static void __exit pmbus_exit(void) +{ + i2c_del_driver(&pmbus_driver); +} + +MODULE_AUTHOR("Guenter Roeck"); +MODULE_DESCRIPTION("Generic PMBus driver"); +MODULE_LICENSE("GPL"); +module_init(pmbus_init); +module_exit(pmbus_exit); diff --git a/drivers/hwmon/pmbus.h b/drivers/hwmon/pmbus.h new file mode 100644 index 00000000000..a81f7f22876 --- /dev/null +++ b/drivers/hwmon/pmbus.h @@ -0,0 +1,313 @@ +/* + * pmbus.h - Common defines and structures for PMBus devices + * + * Copyright (c) 2010, 2011 Ericsson AB. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef PMBUS_H +#define PMBUS_H + +/* + * Registers + */ +#define PMBUS_PAGE 0x00 +#define PMBUS_OPERATION 0x01 +#define PMBUS_ON_OFF_CONFIG 0x02 +#define PMBUS_CLEAR_FAULTS 0x03 +#define PMBUS_PHASE 0x04 + +#define PMBUS_CAPABILITY 0x19 +#define PMBUS_QUERY 0x1A + +#define PMBUS_VOUT_MODE 0x20 +#define PMBUS_VOUT_COMMAND 0x21 +#define PMBUS_VOUT_TRIM 0x22 +#define PMBUS_VOUT_CAL_OFFSET 0x23 +#define PMBUS_VOUT_MAX 0x24 +#define PMBUS_VOUT_MARGIN_HIGH 0x25 +#define PMBUS_VOUT_MARGIN_LOW 0x26 +#define PMBUS_VOUT_TRANSITION_RATE 0x27 +#define PMBUS_VOUT_DROOP 0x28 +#define PMBUS_VOUT_SCALE_LOOP 0x29 +#define PMBUS_VOUT_SCALE_MONITOR 0x2A + +#define PMBUS_COEFFICIENTS 0x30 +#define PMBUS_POUT_MAX 0x31 + +#define PMBUS_FAN_CONFIG_12 0x3A +#define PMBUS_FAN_COMMAND_1 0x3B +#define PMBUS_FAN_COMMAND_2 0x3C +#define PMBUS_FAN_CONFIG_34 0x3D +#define PMBUS_FAN_COMMAND_3 0x3E +#define PMBUS_FAN_COMMAND_4 0x3F + +#define PMBUS_VOUT_OV_FAULT_LIMIT 0x40 +#define PMBUS_VOUT_OV_FAULT_RESPONSE 0x41 +#define PMBUS_VOUT_OV_WARN_LIMIT 0x42 +#define PMBUS_VOUT_UV_WARN_LIMIT 0x43 +#define PMBUS_VOUT_UV_FAULT_LIMIT 0x44 +#define PMBUS_VOUT_UV_FAULT_RESPONSE 0x45 +#define PMBUS_IOUT_OC_FAULT_LIMIT 0x46 +#define PMBUS_IOUT_OC_FAULT_RESPONSE 0x47 +#define PMBUS_IOUT_OC_LV_FAULT_LIMIT 0x48 +#define PMBUS_IOUT_OC_LV_FAULT_RESPONSE 0x49 +#define PMBUS_IOUT_OC_WARN_LIMIT 0x4A +#define PMBUS_IOUT_UC_FAULT_LIMIT 0x4B +#define PMBUS_IOUT_UC_FAULT_RESPONSE 0x4C + +#define PMBUS_OT_FAULT_LIMIT 0x4F +#define PMBUS_OT_FAULT_RESPONSE 0x50 +#define PMBUS_OT_WARN_LIMIT 0x51 +#define PMBUS_UT_WARN_LIMIT 0x52 +#define PMBUS_UT_FAULT_LIMIT 0x53 +#define PMBUS_UT_FAULT_RESPONSE 0x54 +#define PMBUS_VIN_OV_FAULT_LIMIT 0x55 +#define PMBUS_VIN_OV_FAULT_RESPONSE 0x56 +#define PMBUS_VIN_OV_WARN_LIMIT 0x57 +#define PMBUS_VIN_UV_WARN_LIMIT 0x58 +#define PMBUS_VIN_UV_FAULT_LIMIT 0x59 + +#define PMBUS_IIN_OC_FAULT_LIMIT 0x5B +#define PMBUS_IIN_OC_WARN_LIMIT 0x5D + +#define PMBUS_POUT_OP_FAULT_LIMIT 0x68 +#define PMBUS_POUT_OP_WARN_LIMIT 0x6A +#define PMBUS_PIN_OP_WARN_LIMIT 0x6B + +#define PMBUS_STATUS_BYTE 0x78 +#define PMBUS_STATUS_WORD 0x79 +#define PMBUS_STATUS_VOUT 0x7A +#define PMBUS_STATUS_IOUT 0x7B +#define PMBUS_STATUS_INPUT 0x7C +#define PMBUS_STATUS_TEMPERATURE 0x7D +#define PMBUS_STATUS_CML 0x7E +#define PMBUS_STATUS_OTHER 0x7F +#define PMBUS_STATUS_MFR_SPECIFIC 0x80 +#define PMBUS_STATUS_FAN_12 0x81 +#define PMBUS_STATUS_FAN_34 0x82 + +#define PMBUS_READ_VIN 0x88 +#define PMBUS_READ_IIN 0x89 +#define PMBUS_READ_VCAP 0x8A +#define PMBUS_READ_VOUT 0x8B +#define PMBUS_READ_IOUT 0x8C +#define PMBUS_READ_TEMPERATURE_1 0x8D +#define PMBUS_READ_TEMPERATURE_2 0x8E +#define PMBUS_READ_TEMPERATURE_3 0x8F +#define PMBUS_READ_FAN_SPEED_1 0x90 +#define PMBUS_READ_FAN_SPEED_2 0x91 +#define PMBUS_READ_FAN_SPEED_3 0x92 +#define PMBUS_READ_FAN_SPEED_4 0x93 +#define PMBUS_READ_DUTY_CYCLE 0x94 +#define PMBUS_READ_FREQUENCY 0x95 +#define PMBUS_READ_POUT 0x96 +#define PMBUS_READ_PIN 0x97 + +#define PMBUS_REVISION 0x98 +#define PMBUS_MFR_ID 0x99 +#define PMBUS_MFR_MODEL 0x9A +#define PMBUS_MFR_REVISION 0x9B +#define PMBUS_MFR_LOCATION 0x9C +#define PMBUS_MFR_DATE 0x9D +#define PMBUS_MFR_SERIAL 0x9E + +/* + * CAPABILITY + */ +#define PB_CAPABILITY_SMBALERT (1<<4) +#define PB_CAPABILITY_ERROR_CHECK (1<<7) + +/* + * VOUT_MODE + */ +#define PB_VOUT_MODE_MODE_MASK 0xe0 +#define PB_VOUT_MODE_PARAM_MASK 0x1f + +#define PB_VOUT_MODE_LINEAR 0x00 +#define PB_VOUT_MODE_VID 0x20 +#define PB_VOUT_MODE_DIRECT 0x40 + +/* + * Fan configuration + */ +#define PB_FAN_2_PULSE_MASK ((1 << 0) | (1 << 1)) +#define PB_FAN_2_RPM (1 << 2) +#define PB_FAN_2_INSTALLED (1 << 3) +#define PB_FAN_1_PULSE_MASK ((1 << 4) | (1 << 5)) +#define PB_FAN_1_RPM (1 << 6) +#define PB_FAN_1_INSTALLED (1 << 7) + +/* + * STATUS_BYTE, STATUS_WORD (lower) + */ +#define PB_STATUS_NONE_ABOVE (1<<0) +#define PB_STATUS_CML (1<<1) +#define PB_STATUS_TEMPERATURE (1<<2) +#define PB_STATUS_VIN_UV (1<<3) +#define PB_STATUS_IOUT_OC (1<<4) +#define PB_STATUS_VOUT_OV (1<<5) +#define PB_STATUS_OFF (1<<6) +#define PB_STATUS_BUSY (1<<7) + +/* + * STATUS_WORD (upper) + */ +#define PB_STATUS_UNKNOWN (1<<8) +#define PB_STATUS_OTHER (1<<9) +#define PB_STATUS_FANS (1<<10) +#define PB_STATUS_POWER_GOOD_N (1<<11) +#define PB_STATUS_WORD_MFR (1<<12) +#define PB_STATUS_INPUT (1<<13) +#define PB_STATUS_IOUT_POUT (1<<14) +#define PB_STATUS_VOUT (1<<15) + +/* + * STATUS_IOUT + */ +#define PB_POUT_OP_WARNING (1<<0) +#define PB_POUT_OP_FAULT (1<<1) +#define PB_POWER_LIMITING (1<<2) +#define PB_CURRENT_SHARE_FAULT (1<<3) +#define PB_IOUT_UC_FAULT (1<<4) +#define PB_IOUT_OC_WARNING (1<<5) +#define PB_IOUT_OC_LV_FAULT (1<<6) +#define PB_IOUT_OC_FAULT (1<<7) + +/* + * STATUS_VOUT, STATUS_INPUT + */ +#define PB_VOLTAGE_UV_FAULT (1<<4) +#define PB_VOLTAGE_UV_WARNING (1<<5) +#define PB_VOLTAGE_OV_WARNING (1<<6) +#define PB_VOLTAGE_OV_FAULT (1<<7) + +/* + * STATUS_INPUT + */ +#define PB_PIN_OP_WARNING (1<<0) +#define PB_IIN_OC_WARNING (1<<1) +#define PB_IIN_OC_FAULT (1<<2) + +/* + * STATUS_TEMPERATURE + */ +#define PB_TEMP_UT_FAULT (1<<4) +#define PB_TEMP_UT_WARNING (1<<5) +#define PB_TEMP_OT_WARNING (1<<6) +#define PB_TEMP_OT_FAULT (1<<7) + +/* + * STATUS_FAN + */ +#define PB_FAN_AIRFLOW_WARNING (1<<0) +#define PB_FAN_AIRFLOW_FAULT (1<<1) +#define PB_FAN_FAN2_SPEED_OVERRIDE (1<<2) +#define PB_FAN_FAN1_SPEED_OVERRIDE (1<<3) +#define PB_FAN_FAN2_WARNING (1<<4) +#define PB_FAN_FAN1_WARNING (1<<5) +#define PB_FAN_FAN2_FAULT (1<<6) +#define PB_FAN_FAN1_FAULT (1<<7) + +/* + * CML_FAULT_STATUS + */ +#define PB_CML_FAULT_OTHER_MEM_LOGIC (1<<0) +#define PB_CML_FAULT_OTHER_COMM (1<<1) +#define PB_CML_FAULT_PROCESSOR (1<<3) +#define PB_CML_FAULT_MEMORY (1<<4) +#define PB_CML_FAULT_PACKET_ERROR (1<<5) +#define PB_CML_FAULT_INVALID_DATA (1<<6) +#define PB_CML_FAULT_INVALID_COMMAND (1<<7) + +enum pmbus_sensor_classes { + PSC_VOLTAGE_IN = 0, + PSC_VOLTAGE_OUT, + PSC_CURRENT_IN, + PSC_CURRENT_OUT, + PSC_POWER, + PSC_TEMPERATURE, + PSC_FAN, + PSC_NUM_CLASSES /* Number of power sensor classes */ +}; + +#define PMBUS_PAGES 32 /* Per PMBus specification */ + +/* Functionality bit mask */ +#define PMBUS_HAVE_VIN (1 << 0) +#define PMBUS_HAVE_VCAP (1 << 1) +#define PMBUS_HAVE_VOUT (1 << 2) +#define PMBUS_HAVE_IIN (1 << 3) +#define PMBUS_HAVE_IOUT (1 << 4) +#define PMBUS_HAVE_PIN (1 << 5) +#define PMBUS_HAVE_POUT (1 << 6) +#define PMBUS_HAVE_FAN12 (1 << 7) +#define PMBUS_HAVE_FAN34 (1 << 8) +#define PMBUS_HAVE_TEMP (1 << 9) +#define PMBUS_HAVE_TEMP2 (1 << 10) +#define PMBUS_HAVE_TEMP3 (1 << 11) +#define PMBUS_HAVE_STATUS_VOUT (1 << 12) +#define PMBUS_HAVE_STATUS_IOUT (1 << 13) +#define PMBUS_HAVE_STATUS_INPUT (1 << 14) +#define PMBUS_HAVE_STATUS_TEMP (1 << 15) +#define PMBUS_HAVE_STATUS_FAN12 (1 << 16) +#define PMBUS_HAVE_STATUS_FAN34 (1 << 17) + +struct pmbus_driver_info { + int pages; /* Total number of pages */ + bool direct[PSC_NUM_CLASSES]; + /* true if device uses direct data format + for the given sensor class */ + /* + * Support one set of coefficients for each sensor type + * Used for chips providing data in direct mode. + */ + int m[PSC_NUM_CLASSES]; /* mantissa for direct data format */ + int b[PSC_NUM_CLASSES]; /* offset */ + int R[PSC_NUM_CLASSES]; /* exponent */ + + u32 func[PMBUS_PAGES]; /* Functionality, per page */ + /* + * The get_status function maps manufacturing specific status values + * into PMBus standard status values. + * This function is optional and only necessary if chip specific status + * register values have to be mapped into standard PMBus status register + * values. + */ + int (*get_status)(struct i2c_client *client, int page, int reg); + /* + * The identify function determines supported PMBus functionality. + * This function is only necessary if a chip driver supports multiple + * chips, and the chip functionality is not pre-determined. + */ + int (*identify)(struct i2c_client *client, + struct pmbus_driver_info *info); +}; + +/* Function declarations */ + +int pmbus_set_page(struct i2c_client *client, u8 page); +int pmbus_read_word_data(struct i2c_client *client, u8 page, u8 reg); +void pmbus_clear_faults(struct i2c_client *client); +bool pmbus_check_byte_register(struct i2c_client *client, int page, int reg); +bool pmbus_check_word_register(struct i2c_client *client, int page, int reg); +int pmbus_do_probe(struct i2c_client *client, const struct i2c_device_id *id, + struct pmbus_driver_info *info); +int pmbus_do_remove(struct i2c_client *client); +const struct pmbus_driver_info *pmbus_get_driver_info(struct i2c_client + *client); + +#endif /* PMBUS_H */ diff --git a/drivers/hwmon/pmbus_core.c b/drivers/hwmon/pmbus_core.c new file mode 100644 index 00000000000..6474512f49b --- /dev/null +++ b/drivers/hwmon/pmbus_core.c @@ -0,0 +1,1658 @@ +/* + * Hardware monitoring driver for PMBus devices + * + * Copyright (c) 2010, 2011 Ericsson AB. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/delay.h> +#include <linux/i2c/pmbus.h> +#include "pmbus.h" + +/* + * Constants needed to determine number of sensors, booleans, and labels. + */ +#define PMBUS_MAX_INPUT_SENSORS 11 /* 6*volt, 3*curr, 2*power */ +#define PMBUS_VOUT_SENSORS_PER_PAGE 5 /* input, min, max, lcrit, + crit */ +#define PMBUS_IOUT_SENSORS_PER_PAGE 4 /* input, min, max, crit */ +#define PMBUS_POUT_SENSORS_PER_PAGE 4 /* input, cap, max, crit */ +#define PMBUS_MAX_SENSORS_PER_FAN 1 /* input */ +#define PMBUS_MAX_SENSORS_PER_TEMP 5 /* input, min, max, lcrit, + crit */ + +#define PMBUS_MAX_INPUT_BOOLEANS 7 /* v: min_alarm, max_alarm, + lcrit_alarm, crit_alarm; + c: alarm, crit_alarm; + p: crit_alarm */ +#define PMBUS_VOUT_BOOLEANS_PER_PAGE 4 /* min_alarm, max_alarm, + lcrit_alarm, crit_alarm */ +#define PMBUS_IOUT_BOOLEANS_PER_PAGE 3 /* alarm, lcrit_alarm, + crit_alarm */ +#define PMBUS_POUT_BOOLEANS_PER_PAGE 2 /* alarm, crit_alarm */ +#define PMBUS_MAX_BOOLEANS_PER_FAN 2 /* alarm, fault */ +#define PMBUS_MAX_BOOLEANS_PER_TEMP 4 /* min_alarm, max_alarm, + lcrit_alarm, crit_alarm */ + +#define PMBUS_MAX_INPUT_LABELS 4 /* vin, vcap, iin, pin */ + +/* + * status, status_vout, status_iout, status_fans, status_fan34, and status_temp + * are paged. status_input is unpaged. + */ +#define PB_NUM_STATUS_REG (PMBUS_PAGES * 6 + 1) + +/* + * Index into status register array, per status register group + */ +#define PB_STATUS_BASE 0 +#define PB_STATUS_VOUT_BASE (PB_STATUS_BASE + PMBUS_PAGES) +#define PB_STATUS_IOUT_BASE (PB_STATUS_VOUT_BASE + PMBUS_PAGES) +#define PB_STATUS_FAN_BASE (PB_STATUS_IOUT_BASE + PMBUS_PAGES) +#define PB_STATUS_FAN34_BASE (PB_STATUS_FAN_BASE + PMBUS_PAGES) +#define PB_STATUS_INPUT_BASE (PB_STATUS_FAN34_BASE + PMBUS_PAGES) +#define PB_STATUS_TEMP_BASE (PB_STATUS_INPUT_BASE + 1) + +struct pmbus_sensor { + char name[I2C_NAME_SIZE]; /* sysfs sensor name */ + struct sensor_device_attribute attribute; + u8 page; /* page number */ + u8 reg; /* register */ + enum pmbus_sensor_classes class; /* sensor class */ + bool update; /* runtime sensor update needed */ + int data; /* Sensor data. + Negative if there was a read error */ +}; + +struct pmbus_boolean { + char name[I2C_NAME_SIZE]; /* sysfs boolean name */ + struct sensor_device_attribute attribute; +}; + +struct pmbus_label { + char name[I2C_NAME_SIZE]; /* sysfs label name */ + struct sensor_device_attribute attribute; + char label[I2C_NAME_SIZE]; /* label */ +}; + +struct pmbus_data { + struct device *hwmon_dev; + + u32 flags; /* from platform data */ + + int exponent; /* linear mode: exponent for output voltages */ + + const struct pmbus_driver_info *info; + + int max_attributes; + int num_attributes; + struct attribute **attributes; + struct attribute_group group; + + /* + * Sensors cover both sensor and limit registers. + */ + int max_sensors; + int num_sensors; + struct pmbus_sensor *sensors; + /* + * Booleans are used for alarms. + * Values are determined from status registers. + */ + int max_booleans; + int num_booleans; + struct pmbus_boolean *booleans; + /* + * Labels are used to map generic names (e.g., "in1") + * to PMBus specific names (e.g., "vin" or "vout1"). + */ + int max_labels; + int num_labels; + struct pmbus_label *labels; + + struct mutex update_lock; + bool valid; + unsigned long last_updated; /* in jiffies */ + + /* + * A single status register covers multiple attributes, + * so we keep them all together. + */ + u8 status_bits; + u8 status[PB_NUM_STATUS_REG]; + + u8 currpage; +}; + +int pmbus_set_page(struct i2c_client *client, u8 page) +{ + struct pmbus_data *data = i2c_get_clientdata(client); + int rv = 0; + int newpage; + + if (page != data->currpage) { + rv = i2c_smbus_write_byte_data(client, PMBUS_PAGE, page); + newpage = i2c_smbus_read_byte_data(client, PMBUS_PAGE); + if (newpage != page) + rv = -EINVAL; + else + data->currpage = page; + } + return rv; +} +EXPORT_SYMBOL_GPL(pmbus_set_page); + +static int pmbus_write_byte(struct i2c_client *client, u8 page, u8 value) +{ + int rv; + + rv = pmbus_set_page(client, page); + if (rv < 0) + return rv; + + return i2c_smbus_write_byte(client, value); +} + +static int pmbus_write_word_data(struct i2c_client *client, u8 page, u8 reg, + u16 word) +{ + int rv; + + rv = pmbus_set_page(client, page); + if (rv < 0) + return rv; + + return i2c_smbus_write_word_data(client, reg, word); +} + +int pmbus_read_word_data(struct i2c_client *client, u8 page, u8 reg) +{ + int rv; + + rv = pmbus_set_page(client, page); + if (rv < 0) + return rv; + + return i2c_smbus_read_word_data(client, reg); +} +EXPORT_SYMBOL_GPL(pmbus_read_word_data); + +static int pmbus_read_byte_data(struct i2c_client *client, u8 page, u8 reg) +{ + int rv; + + rv = pmbus_set_page(client, page); + if (rv < 0) + return rv; + + return i2c_smbus_read_byte_data(client, reg); +} + +static void pmbus_clear_fault_page(struct i2c_client *client, int page) +{ + pmbus_write_byte(client, page, PMBUS_CLEAR_FAULTS); +} + +void pmbus_clear_faults(struct i2c_client *client) +{ + struct pmbus_data *data = i2c_get_clientdata(client); + int i; + + for (i = 0; i < data->info->pages; i++) + pmbus_clear_fault_page(client, i); +} +EXPORT_SYMBOL_GPL(pmbus_clear_faults); + +static int pmbus_check_status_cml(struct i2c_client *client, int page) +{ + int status, status2; + + status = pmbus_read_byte_data(client, page, PMBUS_STATUS_BYTE); + if (status < 0 || (status & PB_STATUS_CML)) { + status2 = pmbus_read_byte_data(client, page, PMBUS_STATUS_CML); + if (status2 < 0 || (status2 & PB_CML_FAULT_INVALID_COMMAND)) + return -EINVAL; + } + return 0; +} + +bool pmbus_check_byte_register(struct i2c_client *client, int page, int reg) +{ + int rv; + struct pmbus_data *data = i2c_get_clientdata(client); + + rv = pmbus_read_byte_data(client, page, reg); + if (rv >= 0 && !(data->flags & PMBUS_SKIP_STATUS_CHECK)) + rv = pmbus_check_status_cml(client, page); + pmbus_clear_fault_page(client, page); + return rv >= 0; +} +EXPORT_SYMBOL_GPL(pmbus_check_byte_register); + +bool pmbus_check_word_register(struct i2c_client *client, int page, int reg) +{ + int rv; + struct pmbus_data *data = i2c_get_clientdata(client); + + rv = pmbus_read_word_data(client, page, reg); + if (rv >= 0 && !(data->flags & PMBUS_SKIP_STATUS_CHECK)) + rv = pmbus_check_status_cml(client, page); + pmbus_clear_fault_page(client, page); + return rv >= 0; +} +EXPORT_SYMBOL_GPL(pmbus_check_word_register); + +const struct pmbus_driver_info *pmbus_get_driver_info(struct i2c_client *client) +{ + struct pmbus_data *data = i2c_get_clientdata(client); + + return data->info; +} +EXPORT_SYMBOL_GPL(pmbus_get_driver_info); + +static int pmbus_get_status(struct i2c_client *client, int page, int reg) +{ + struct pmbus_data *data = i2c_get_clientdata(client); + const struct pmbus_driver_info *info = data->info; + int status; + + if (info->get_status) { + status = info->get_status(client, page, reg); + if (status != -ENODATA) + return status; + } + return pmbus_read_byte_data(client, page, reg); +} + +static struct pmbus_data *pmbus_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct pmbus_data *data = i2c_get_clientdata(client); + const struct pmbus_driver_info *info = data->info; + + mutex_lock(&data->update_lock); + if (time_after(jiffies, data->last_updated + HZ) || !data->valid) { + int i; + + for (i = 0; i < info->pages; i++) + data->status[PB_STATUS_BASE + i] + = pmbus_read_byte_data(client, i, + PMBUS_STATUS_BYTE); + for (i = 0; i < info->pages; i++) { + if (!(info->func[i] & PMBUS_HAVE_STATUS_VOUT)) + continue; + data->status[PB_STATUS_VOUT_BASE + i] + = pmbus_get_status(client, i, PMBUS_STATUS_VOUT); + } + for (i = 0; i < info->pages; i++) { + if (!(info->func[i] & PMBUS_HAVE_STATUS_IOUT)) + continue; + data->status[PB_STATUS_IOUT_BASE + i] + = pmbus_get_status(client, i, PMBUS_STATUS_IOUT); + } + for (i = 0; i < info->pages; i++) { + if (!(info->func[i] & PMBUS_HAVE_STATUS_TEMP)) + continue; + data->status[PB_STATUS_TEMP_BASE + i] + = pmbus_get_status(client, i, + PMBUS_STATUS_TEMPERATURE); + } + for (i = 0; i < info->pages; i++) { + if (!(info->func[i] & PMBUS_HAVE_STATUS_FAN12)) + continue; + data->status[PB_STATUS_FAN_BASE + i] + = pmbus_get_status(client, i, PMBUS_STATUS_FAN_12); + } + + for (i = 0; i < info->pages; i++) { + if (!(info->func[i] & PMBUS_HAVE_STATUS_FAN34)) + continue; + data->status[PB_STATUS_FAN34_BASE + i] + = pmbus_get_status(client, i, PMBUS_STATUS_FAN_34); + } + + if (info->func[0] & PMBUS_HAVE_STATUS_INPUT) + data->status[PB_STATUS_INPUT_BASE] + = pmbus_get_status(client, 0, PMBUS_STATUS_INPUT); + + for (i = 0; i < data->num_sensors; i++) { + struct pmbus_sensor *sensor = &data->sensors[i]; + + if (!data->valid || sensor->update) + sensor->data + = pmbus_read_word_data(client, sensor->page, + sensor->reg); + } + pmbus_clear_faults(client); + data->last_updated = jiffies; + data->valid = 1; + } + mutex_unlock(&data->update_lock); + return data; +} + +/* + * Convert linear sensor values to milli- or micro-units + * depending on sensor type. + */ +static int pmbus_reg2data_linear(struct pmbus_data *data, + struct pmbus_sensor *sensor) +{ + s16 exponent; + s32 mantissa; + long val; + + if (sensor->class == PSC_VOLTAGE_OUT) { /* LINEAR16 */ + exponent = data->exponent; + mantissa = (u16) sensor->data; + } else { /* LINEAR11 */ + exponent = (sensor->data >> 11) & 0x001f; + mantissa = sensor->data & 0x07ff; + + if (exponent > 0x0f) + exponent |= 0xffe0; /* sign extend exponent */ + if (mantissa > 0x03ff) + mantissa |= 0xfffff800; /* sign extend mantissa */ + } + + val = mantissa; + + /* scale result to milli-units for all sensors except fans */ + if (sensor->class != PSC_FAN) + val = val * 1000L; + + /* scale result to micro-units for power sensors */ + if (sensor->class == PSC_POWER) + val = val * 1000L; + + if (exponent >= 0) + val <<= exponent; + else + val >>= -exponent; + + return (int)val; +} + +/* + * Convert direct sensor values to milli- or micro-units + * depending on sensor type. + */ +static int pmbus_reg2data_direct(struct pmbus_data *data, + struct pmbus_sensor *sensor) +{ + long val = (s16) sensor->data; + long m, b, R; + + m = data->info->m[sensor->class]; + b = data->info->b[sensor->class]; + R = data->info->R[sensor->class]; + + if (m == 0) + return 0; + + /* X = 1/m * (Y * 10^-R - b) */ + R = -R; + /* scale result to milli-units for everything but fans */ + if (sensor->class != PSC_FAN) { + R += 3; + b *= 1000; + } + + /* scale result to micro-units for power sensors */ + if (sensor->class == PSC_POWER) { + R += 3; + b *= 1000; + } + + while (R > 0) { + val *= 10; + R--; + } + while (R < 0) { + val = DIV_ROUND_CLOSEST(val, 10); + R++; + } + + return (int)((val - b) / m); +} + +static int pmbus_reg2data(struct pmbus_data *data, struct pmbus_sensor *sensor) +{ + int val; + + if (data->info->direct[sensor->class]) + val = pmbus_reg2data_direct(data, sensor); + else + val = pmbus_reg2data_linear(data, sensor); + + return val; +} + +#define MAX_MANTISSA (1023 * 1000) +#define MIN_MANTISSA (511 * 1000) + +static u16 pmbus_data2reg_linear(struct pmbus_data *data, + enum pmbus_sensor_classes class, long val) +{ + s16 exponent = 0, mantissa; + bool negative = false; + + /* simple case */ + if (val == 0) + return 0; + + if (class == PSC_VOLTAGE_OUT) { + /* LINEAR16 does not support negative voltages */ + if (val < 0) + return 0; + + /* + * For a static exponents, we don't have a choice + * but to adjust the value to it. + */ + if (data->exponent < 0) + val <<= -data->exponent; + else + val >>= data->exponent; + val = DIV_ROUND_CLOSEST(val, 1000); + return val & 0xffff; + } + + if (val < 0) { + negative = true; + val = -val; + } + + /* Power is in uW. Convert to mW before converting. */ + if (class == PSC_POWER) + val = DIV_ROUND_CLOSEST(val, 1000L); + + /* + * For simplicity, convert fan data to milli-units + * before calculating the exponent. + */ + if (class == PSC_FAN) + val = val * 1000; + + /* Reduce large mantissa until it fits into 10 bit */ + while (val >= MAX_MANTISSA && exponent < 15) { + exponent++; + val >>= 1; + } + /* Increase small mantissa to improve precision */ + while (val < MIN_MANTISSA && exponent > -15) { + exponent--; + val <<= 1; + } + + /* Convert mantissa from milli-units to units */ + mantissa = DIV_ROUND_CLOSEST(val, 1000); + + /* Ensure that resulting number is within range */ + if (mantissa > 0x3ff) + mantissa = 0x3ff; + + /* restore sign */ + if (negative) + mantissa = -mantissa; + + /* Convert to 5 bit exponent, 11 bit mantissa */ + return (mantissa & 0x7ff) | ((exponent << 11) & 0xf800); +} + +static u16 pmbus_data2reg_direct(struct pmbus_data *data, + enum pmbus_sensor_classes class, long val) +{ + long m, b, R; + + m = data->info->m[class]; + b = data->info->b[class]; + R = data->info->R[class]; + + /* Power is in uW. Adjust R and b. */ + if (class == PSC_POWER) { + R -= 3; + b *= 1000; + } + + /* Calculate Y = (m * X + b) * 10^R */ + if (class != PSC_FAN) { + R -= 3; /* Adjust R and b for data in milli-units */ + b *= 1000; + } + val = val * m + b; + + while (R > 0) { + val *= 10; + R--; + } + while (R < 0) { + val = DIV_ROUND_CLOSEST(val, 10); + R++; + } + + return val; +} + +static u16 pmbus_data2reg(struct pmbus_data *data, + enum pmbus_sensor_classes class, long val) +{ + u16 regval; + + if (data->info->direct[class]) + regval = pmbus_data2reg_direct(data, class, val); + else + regval = pmbus_data2reg_linear(data, class, val); + + return regval; +} + +/* + * Return boolean calculated from converted data. + * <index> defines a status register index and mask, and optionally + * two sensor indexes. + * The upper half-word references the two sensors, + * two sensor indices. + * The upper half-word references the two optional sensors, + * the lower half word references status register and mask. + * The function returns true if (status[reg] & mask) is true and, + * if specified, if v1 >= v2. + * To determine if an object exceeds upper limits, specify <v, limit>. + * To determine if an object exceeds lower limits, specify <limit, v>. + * + * For booleans created with pmbus_add_boolean_reg(), only the lower 16 bits of + * index are set. s1 and s2 (the sensor index values) are zero in this case. + * The function returns true if (status[reg] & mask) is true. + * + * If the boolean was created with pmbus_add_boolean_cmp(), a comparison against + * a specified limit has to be performed to determine the boolean result. + * In this case, the function returns true if v1 >= v2 (where v1 and v2 are + * sensor values referenced by sensor indices s1 and s2). + * + * To determine if an object exceeds upper limits, specify <s1,s2> = <v,limit>. + * To determine if an object exceeds lower limits, specify <s1,s2> = <limit,v>. + * + * If a negative value is stored in any of the referenced registers, this value + * reflects an error code which will be returned. + */ +static int pmbus_get_boolean(struct pmbus_data *data, int index, int *val) +{ + u8 s1 = (index >> 24) & 0xff; + u8 s2 = (index >> 16) & 0xff; + u8 reg = (index >> 8) & 0xff; + u8 mask = index & 0xff; + int status; + u8 regval; + + status = data->status[reg]; + if (status < 0) + return status; + + regval = status & mask; + if (!s1 && !s2) + *val = !!regval; + else { + int v1, v2; + struct pmbus_sensor *sensor1, *sensor2; + + sensor1 = &data->sensors[s1]; + if (sensor1->data < 0) + return sensor1->data; + sensor2 = &data->sensors[s2]; + if (sensor2->data < 0) + return sensor2->data; + + v1 = pmbus_reg2data(data, sensor1); + v2 = pmbus_reg2data(data, sensor2); + *val = !!(regval && v1 >= v2); + } + return 0; +} + +static ssize_t pmbus_show_boolean(struct device *dev, + struct device_attribute *da, char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); + struct pmbus_data *data = pmbus_update_device(dev); + int val; + int err; + + err = pmbus_get_boolean(data, attr->index, &val); + if (err) + return err; + return snprintf(buf, PAGE_SIZE, "%d\n", val); +} + +static ssize_t pmbus_show_sensor(struct device *dev, + struct device_attribute *da, char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); + struct pmbus_data *data = pmbus_update_device(dev); + struct pmbus_sensor *sensor; + + sensor = &data->sensors[attr->index]; + if (sensor->data < 0) + return sensor->data; + + return snprintf(buf, PAGE_SIZE, "%d\n", pmbus_reg2data(data, sensor)); +} + +static ssize_t pmbus_set_sensor(struct device *dev, + struct device_attribute *devattr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct pmbus_data *data = i2c_get_clientdata(client); + struct pmbus_sensor *sensor = &data->sensors[attr->index]; + ssize_t rv = count; + long val = 0; + int ret; + u16 regval; + + if (strict_strtol(buf, 10, &val) < 0) + return -EINVAL; + + mutex_lock(&data->update_lock); + regval = pmbus_data2reg(data, sensor->class, val); + ret = pmbus_write_word_data(client, sensor->page, sensor->reg, regval); + if (ret < 0) + rv = ret; + else + data->sensors[attr->index].data = regval; + mutex_unlock(&data->update_lock); + return rv; +} + +static ssize_t pmbus_show_label(struct device *dev, + struct device_attribute *da, char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct pmbus_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); + + return snprintf(buf, PAGE_SIZE, "%s\n", + data->labels[attr->index].label); +} + +#define PMBUS_ADD_ATTR(data, _name, _idx, _mode, _type, _show, _set) \ +do { \ + struct sensor_device_attribute *a \ + = &data->_type##s[data->num_##_type##s].attribute; \ + BUG_ON(data->num_attributes >= data->max_attributes); \ + a->dev_attr.attr.name = _name; \ + a->dev_attr.attr.mode = _mode; \ + a->dev_attr.show = _show; \ + a->dev_attr.store = _set; \ + a->index = _idx; \ + data->attributes[data->num_attributes] = &a->dev_attr.attr; \ + data->num_attributes++; \ +} while (0) + +#define PMBUS_ADD_GET_ATTR(data, _name, _type, _idx) \ + PMBUS_ADD_ATTR(data, _name, _idx, S_IRUGO, _type, \ + pmbus_show_##_type, NULL) + +#define PMBUS_ADD_SET_ATTR(data, _name, _type, _idx) \ + PMBUS_ADD_ATTR(data, _name, _idx, S_IWUSR | S_IRUGO, _type, \ + pmbus_show_##_type, pmbus_set_##_type) + +static void pmbus_add_boolean(struct pmbus_data *data, + const char *name, const char *type, int seq, + int idx) +{ + struct pmbus_boolean *boolean; + + BUG_ON(data->num_booleans >= data->max_booleans); + + boolean = &data->booleans[data->num_booleans]; + + snprintf(boolean->name, sizeof(boolean->name), "%s%d_%s", + name, seq, type); + PMBUS_ADD_GET_ATTR(data, boolean->name, boolean, idx); + data->num_booleans++; +} + +static void pmbus_add_boolean_reg(struct pmbus_data *data, + const char *name, const char *type, + int seq, int reg, int bit) +{ + pmbus_add_boolean(data, name, type, seq, (reg << 8) | bit); +} + +static void pmbus_add_boolean_cmp(struct pmbus_data *data, + const char *name, const char *type, + int seq, int i1, int i2, int reg, int mask) +{ + pmbus_add_boolean(data, name, type, seq, + (i1 << 24) | (i2 << 16) | (reg << 8) | mask); +} + +static void pmbus_add_sensor(struct pmbus_data *data, + const char *name, const char *type, int seq, + int page, int reg, enum pmbus_sensor_classes class, + bool update) +{ + struct pmbus_sensor *sensor; + + BUG_ON(data->num_sensors >= data->max_sensors); + + sensor = &data->sensors[data->num_sensors]; + snprintf(sensor->name, sizeof(sensor->name), "%s%d_%s", + name, seq, type); + sensor->page = page; + sensor->reg = reg; + sensor->class = class; + sensor->update = update; + if (update) + PMBUS_ADD_GET_ATTR(data, sensor->name, sensor, + data->num_sensors); + else + PMBUS_ADD_SET_ATTR(data, sensor->name, sensor, + data->num_sensors); + data->num_sensors++; +} + +static void pmbus_add_label(struct pmbus_data *data, + const char *name, int seq, + const char *lstring, int index) +{ + struct pmbus_label *label; + + BUG_ON(data->num_labels >= data->max_labels); + + label = &data->labels[data->num_labels]; + snprintf(label->name, sizeof(label->name), "%s%d_label", name, seq); + if (!index) + strncpy(label->label, lstring, sizeof(label->label) - 1); + else + snprintf(label->label, sizeof(label->label), "%s%d", lstring, + index); + + PMBUS_ADD_GET_ATTR(data, label->name, label, data->num_labels); + data->num_labels++; +} + +static const int pmbus_temp_registers[] = { + PMBUS_READ_TEMPERATURE_1, + PMBUS_READ_TEMPERATURE_2, + PMBUS_READ_TEMPERATURE_3 +}; + +static const int pmbus_temp_flags[] = { + PMBUS_HAVE_TEMP, + PMBUS_HAVE_TEMP2, + PMBUS_HAVE_TEMP3 +}; + +static const int pmbus_fan_registers[] = { + PMBUS_READ_FAN_SPEED_1, + PMBUS_READ_FAN_SPEED_2, + PMBUS_READ_FAN_SPEED_3, + PMBUS_READ_FAN_SPEED_4 +}; + +static const int pmbus_fan_config_registers[] = { + PMBUS_FAN_CONFIG_12, + PMBUS_FAN_CONFIG_12, + PMBUS_FAN_CONFIG_34, + PMBUS_FAN_CONFIG_34 +}; + +static const int pmbus_fan_status_registers[] = { + PMBUS_STATUS_FAN_12, + PMBUS_STATUS_FAN_12, + PMBUS_STATUS_FAN_34, + PMBUS_STATUS_FAN_34 +}; + +static const u32 pmbus_fan_flags[] = { + PMBUS_HAVE_FAN12, + PMBUS_HAVE_FAN12, + PMBUS_HAVE_FAN34, + PMBUS_HAVE_FAN34 +}; + +static const u32 pmbus_fan_status_flags[] = { + PMBUS_HAVE_STATUS_FAN12, + PMBUS_HAVE_STATUS_FAN12, + PMBUS_HAVE_STATUS_FAN34, + PMBUS_HAVE_STATUS_FAN34 +}; + +/* + * Determine maximum number of sensors, booleans, and labels. + * To keep things simple, only make a rough high estimate. + */ +static void pmbus_find_max_attr(struct i2c_client *client, + struct pmbus_data *data) +{ + const struct pmbus_driver_info *info = data->info; + int page, max_sensors, max_booleans, max_labels; + + max_sensors = PMBUS_MAX_INPUT_SENSORS; + max_booleans = PMBUS_MAX_INPUT_BOOLEANS; + max_labels = PMBUS_MAX_INPUT_LABELS; + + for (page = 0; page < info->pages; page++) { + if (info->func[page] & PMBUS_HAVE_VOUT) { + max_sensors += PMBUS_VOUT_SENSORS_PER_PAGE; + max_booleans += PMBUS_VOUT_BOOLEANS_PER_PAGE; + max_labels++; + } + if (info->func[page] & PMBUS_HAVE_IOUT) { + max_sensors += PMBUS_IOUT_SENSORS_PER_PAGE; + max_booleans += PMBUS_IOUT_BOOLEANS_PER_PAGE; + max_labels++; + } + if (info->func[page] & PMBUS_HAVE_POUT) { + max_sensors += PMBUS_POUT_SENSORS_PER_PAGE; + max_booleans += PMBUS_POUT_BOOLEANS_PER_PAGE; + max_labels++; + } + if (info->func[page] & PMBUS_HAVE_FAN12) { + max_sensors += 2 * PMBUS_MAX_SENSORS_PER_FAN; + max_booleans += 2 * PMBUS_MAX_BOOLEANS_PER_FAN; + } + if (info->func[page] & PMBUS_HAVE_FAN34) { + max_sensors += 2 * PMBUS_MAX_SENSORS_PER_FAN; + max_booleans += 2 * PMBUS_MAX_BOOLEANS_PER_FAN; + } + if (info->func[page] & PMBUS_HAVE_TEMP) { + max_sensors += PMBUS_MAX_SENSORS_PER_TEMP; + max_booleans += PMBUS_MAX_BOOLEANS_PER_TEMP; + } + if (info->func[page] & PMBUS_HAVE_TEMP2) { + max_sensors += PMBUS_MAX_SENSORS_PER_TEMP; + max_booleans += PMBUS_MAX_BOOLEANS_PER_TEMP; + } + if (info->func[page] & PMBUS_HAVE_TEMP3) { + max_sensors += PMBUS_MAX_SENSORS_PER_TEMP; + max_booleans += PMBUS_MAX_BOOLEANS_PER_TEMP; + } + } + data->max_sensors = max_sensors; + data->max_booleans = max_booleans; + data->max_labels = max_labels; + data->max_attributes = max_sensors + max_booleans + max_labels; +} + +/* + * Search for attributes. Allocate sensors, booleans, and labels as needed. + */ +static void pmbus_find_attributes(struct i2c_client *client, + struct pmbus_data *data) +{ + const struct pmbus_driver_info *info = data->info; + int page, i0, i1, in_index; + + /* + * Input voltage sensors + */ + in_index = 1; + if (info->func[0] & PMBUS_HAVE_VIN) { + bool have_alarm = false; + + i0 = data->num_sensors; + pmbus_add_label(data, "in", in_index, "vin", 0); + pmbus_add_sensor(data, "in", "input", in_index, + 0, PMBUS_READ_VIN, PSC_VOLTAGE_IN, true); + if (pmbus_check_word_register(client, 0, + PMBUS_VIN_UV_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "in", "min", in_index, + 0, PMBUS_VIN_UV_WARN_LIMIT, + PSC_VOLTAGE_IN, false); + if (info->func[0] & PMBUS_HAVE_STATUS_INPUT) { + pmbus_add_boolean_reg(data, "in", "min_alarm", + in_index, + PB_STATUS_INPUT_BASE, + PB_VOLTAGE_UV_WARNING); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, 0, + PMBUS_VIN_UV_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "in", "lcrit", in_index, + 0, PMBUS_VIN_UV_FAULT_LIMIT, + PSC_VOLTAGE_IN, false); + if (info->func[0] & PMBUS_HAVE_STATUS_INPUT) { + pmbus_add_boolean_reg(data, "in", "lcrit_alarm", + in_index, + PB_STATUS_INPUT_BASE, + PB_VOLTAGE_UV_FAULT); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, 0, + PMBUS_VIN_OV_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "in", "max", in_index, + 0, PMBUS_VIN_OV_WARN_LIMIT, + PSC_VOLTAGE_IN, false); + if (info->func[0] & PMBUS_HAVE_STATUS_INPUT) { + pmbus_add_boolean_reg(data, "in", "max_alarm", + in_index, + PB_STATUS_INPUT_BASE, + PB_VOLTAGE_OV_WARNING); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, 0, + PMBUS_VIN_OV_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "in", "crit", in_index, + 0, PMBUS_VIN_OV_FAULT_LIMIT, + PSC_VOLTAGE_IN, false); + if (info->func[0] & PMBUS_HAVE_STATUS_INPUT) { + pmbus_add_boolean_reg(data, "in", "crit_alarm", + in_index, + PB_STATUS_INPUT_BASE, + PB_VOLTAGE_OV_FAULT); + have_alarm = true; + } + } + /* + * Add generic alarm attribute only if there are no individual + * attributes. + */ + if (!have_alarm) + pmbus_add_boolean_reg(data, "in", "alarm", + in_index, + PB_STATUS_BASE, + PB_STATUS_VIN_UV); + in_index++; + } + if (info->func[0] & PMBUS_HAVE_VCAP) { + pmbus_add_label(data, "in", in_index, "vcap", 0); + pmbus_add_sensor(data, "in", "input", in_index, 0, + PMBUS_READ_VCAP, PSC_VOLTAGE_IN, true); + in_index++; + } + + /* + * Output voltage sensors + */ + for (page = 0; page < info->pages; page++) { + bool have_alarm = false; + + if (!(info->func[page] & PMBUS_HAVE_VOUT)) + continue; + + i0 = data->num_sensors; + pmbus_add_label(data, "in", in_index, "vout", page + 1); + pmbus_add_sensor(data, "in", "input", in_index, page, + PMBUS_READ_VOUT, PSC_VOLTAGE_OUT, true); + if (pmbus_check_word_register(client, page, + PMBUS_VOUT_UV_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "in", "min", in_index, page, + PMBUS_VOUT_UV_WARN_LIMIT, + PSC_VOLTAGE_OUT, false); + if (info->func[page] & PMBUS_HAVE_STATUS_VOUT) { + pmbus_add_boolean_reg(data, "in", "min_alarm", + in_index, + PB_STATUS_VOUT_BASE + + page, + PB_VOLTAGE_UV_WARNING); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, page, + PMBUS_VOUT_UV_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "in", "lcrit", in_index, page, + PMBUS_VOUT_UV_FAULT_LIMIT, + PSC_VOLTAGE_OUT, false); + if (info->func[page] & PMBUS_HAVE_STATUS_VOUT) { + pmbus_add_boolean_reg(data, "in", "lcrit_alarm", + in_index, + PB_STATUS_VOUT_BASE + + page, + PB_VOLTAGE_UV_FAULT); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, page, + PMBUS_VOUT_OV_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "in", "max", in_index, page, + PMBUS_VOUT_OV_WARN_LIMIT, + PSC_VOLTAGE_OUT, false); + if (info->func[page] & PMBUS_HAVE_STATUS_VOUT) { + pmbus_add_boolean_reg(data, "in", "max_alarm", + in_index, + PB_STATUS_VOUT_BASE + + page, + PB_VOLTAGE_OV_WARNING); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, page, + PMBUS_VOUT_OV_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "in", "crit", in_index, page, + PMBUS_VOUT_OV_FAULT_LIMIT, + PSC_VOLTAGE_OUT, false); + if (info->func[page] & PMBUS_HAVE_STATUS_VOUT) { + pmbus_add_boolean_reg(data, "in", "crit_alarm", + in_index, + PB_STATUS_VOUT_BASE + + page, + PB_VOLTAGE_OV_FAULT); + have_alarm = true; + } + } + /* + * Add generic alarm attribute only if there are no individual + * attributes. + */ + if (!have_alarm) + pmbus_add_boolean_reg(data, "in", "alarm", + in_index, + PB_STATUS_BASE + page, + PB_STATUS_VOUT_OV); + in_index++; + } + + /* + * Current sensors + */ + + /* + * Input current sensors + */ + in_index = 1; + if (info->func[0] & PMBUS_HAVE_IIN) { + i0 = data->num_sensors; + pmbus_add_label(data, "curr", in_index, "iin", 0); + pmbus_add_sensor(data, "curr", "input", in_index, + 0, PMBUS_READ_IIN, PSC_CURRENT_IN, true); + if (pmbus_check_word_register(client, 0, + PMBUS_IIN_OC_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "curr", "max", in_index, + 0, PMBUS_IIN_OC_WARN_LIMIT, + PSC_CURRENT_IN, false); + if (info->func[0] & PMBUS_HAVE_STATUS_INPUT) { + pmbus_add_boolean_reg(data, "curr", "max_alarm", + in_index, + PB_STATUS_INPUT_BASE, + PB_IIN_OC_WARNING); + } + } + if (pmbus_check_word_register(client, 0, + PMBUS_IIN_OC_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "curr", "crit", in_index, + 0, PMBUS_IIN_OC_FAULT_LIMIT, + PSC_CURRENT_IN, false); + if (info->func[0] & PMBUS_HAVE_STATUS_INPUT) + pmbus_add_boolean_reg(data, "curr", + "crit_alarm", + in_index, + PB_STATUS_INPUT_BASE, + PB_IIN_OC_FAULT); + } + in_index++; + } + + /* + * Output current sensors + */ + for (page = 0; page < info->pages; page++) { + bool have_alarm = false; + + if (!(info->func[page] & PMBUS_HAVE_IOUT)) + continue; + + i0 = data->num_sensors; + pmbus_add_label(data, "curr", in_index, "iout", page + 1); + pmbus_add_sensor(data, "curr", "input", in_index, page, + PMBUS_READ_IOUT, PSC_CURRENT_OUT, true); + if (pmbus_check_word_register(client, page, + PMBUS_IOUT_OC_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "curr", "max", in_index, page, + PMBUS_IOUT_OC_WARN_LIMIT, + PSC_CURRENT_OUT, false); + if (info->func[page] & PMBUS_HAVE_STATUS_IOUT) { + pmbus_add_boolean_reg(data, "curr", "max_alarm", + in_index, + PB_STATUS_IOUT_BASE + + page, PB_IOUT_OC_WARNING); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, page, + PMBUS_IOUT_UC_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "curr", "lcrit", in_index, page, + PMBUS_IOUT_UC_FAULT_LIMIT, + PSC_CURRENT_OUT, false); + if (info->func[page] & PMBUS_HAVE_STATUS_IOUT) { + pmbus_add_boolean_reg(data, "curr", + "lcrit_alarm", + in_index, + PB_STATUS_IOUT_BASE + + page, PB_IOUT_UC_FAULT); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, page, + PMBUS_IOUT_OC_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "curr", "crit", in_index, page, + PMBUS_IOUT_OC_FAULT_LIMIT, + PSC_CURRENT_OUT, false); + if (info->func[page] & PMBUS_HAVE_STATUS_IOUT) { + pmbus_add_boolean_reg(data, "curr", + "crit_alarm", + in_index, + PB_STATUS_IOUT_BASE + + page, PB_IOUT_OC_FAULT); + have_alarm = true; + } + } + /* + * Add generic alarm attribute only if there are no individual + * attributes. + */ + if (!have_alarm) + pmbus_add_boolean_reg(data, "curr", "alarm", + in_index, + PB_STATUS_BASE + page, + PB_STATUS_IOUT_OC); + in_index++; + } + + /* + * Power sensors + */ + /* + * Input Power sensors + */ + in_index = 1; + if (info->func[0] & PMBUS_HAVE_PIN) { + i0 = data->num_sensors; + pmbus_add_label(data, "power", in_index, "pin", 0); + pmbus_add_sensor(data, "power", "input", in_index, + 0, PMBUS_READ_PIN, PSC_POWER, true); + if (pmbus_check_word_register(client, 0, + PMBUS_PIN_OP_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "power", "max", in_index, + 0, PMBUS_PIN_OP_WARN_LIMIT, PSC_POWER, + false); + if (info->func[0] & PMBUS_HAVE_STATUS_INPUT) + pmbus_add_boolean_reg(data, "power", + "alarm", + in_index, + PB_STATUS_INPUT_BASE, + PB_PIN_OP_WARNING); + } + in_index++; + } + + /* + * Output Power sensors + */ + for (page = 0; page < info->pages; page++) { + bool need_alarm = false; + + if (!(info->func[page] & PMBUS_HAVE_POUT)) + continue; + + i0 = data->num_sensors; + pmbus_add_label(data, "power", in_index, "pout", page + 1); + pmbus_add_sensor(data, "power", "input", in_index, page, + PMBUS_READ_POUT, PSC_POWER, true); + /* + * Per hwmon sysfs API, power_cap is to be used to limit output + * power. + * We have two registers related to maximum output power, + * PMBUS_POUT_MAX and PMBUS_POUT_OP_WARN_LIMIT. + * PMBUS_POUT_MAX matches the powerX_cap attribute definition. + * There is no attribute in the API to match + * PMBUS_POUT_OP_WARN_LIMIT. We use powerX_max for now. + */ + if (pmbus_check_word_register(client, page, PMBUS_POUT_MAX)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "power", "cap", in_index, page, + PMBUS_POUT_MAX, PSC_POWER, false); + need_alarm = true; + } + if (pmbus_check_word_register(client, page, + PMBUS_POUT_OP_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "power", "max", in_index, page, + PMBUS_POUT_OP_WARN_LIMIT, PSC_POWER, + false); + need_alarm = true; + } + if (need_alarm && (info->func[page] & PMBUS_HAVE_STATUS_IOUT)) + pmbus_add_boolean_reg(data, "power", "alarm", + in_index, + PB_STATUS_IOUT_BASE + page, + PB_POUT_OP_WARNING + | PB_POWER_LIMITING); + + if (pmbus_check_word_register(client, page, + PMBUS_POUT_OP_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "power", "crit", in_index, page, + PMBUS_POUT_OP_FAULT_LIMIT, PSC_POWER, + false); + if (info->func[page] & PMBUS_HAVE_STATUS_IOUT) + pmbus_add_boolean_reg(data, "power", + "crit_alarm", + in_index, + PB_STATUS_IOUT_BASE + + page, + PB_POUT_OP_FAULT); + } + in_index++; + } + + /* + * Temperature sensors + */ + in_index = 1; + for (page = 0; page < info->pages; page++) { + int t; + + for (t = 0; t < ARRAY_SIZE(pmbus_temp_registers); t++) { + bool have_alarm = false; + + /* + * A PMBus chip may support any combination of + * temperature registers on any page. So we can not + * abort after a failure to detect a register, but have + * to continue checking for all registers on all pages. + */ + if (!(info->func[page] & pmbus_temp_flags[t])) + continue; + + if (!pmbus_check_word_register + (client, page, pmbus_temp_registers[t])) + continue; + + i0 = data->num_sensors; + pmbus_add_sensor(data, "temp", "input", in_index, page, + pmbus_temp_registers[t], + PSC_TEMPERATURE, true); + + /* + * PMBus provides only one status register for TEMP1-3. + * Thus, we can not use the status register to determine + * which of the three sensors actually caused an alarm. + * Always compare current temperature against the limit + * registers to determine alarm conditions for a + * specific sensor. + * + * Since there is only one set of limit registers for + * up to three temperature sensors, we need to update + * all limit registers after the limit was changed for + * one of the sensors. This ensures that correct limits + * are reported for all temperature sensors. + */ + if (pmbus_check_word_register + (client, page, PMBUS_UT_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "temp", "min", in_index, + page, PMBUS_UT_WARN_LIMIT, + PSC_TEMPERATURE, true); + if (info->func[page] & PMBUS_HAVE_STATUS_TEMP) { + pmbus_add_boolean_cmp(data, "temp", + "min_alarm", in_index, i1, i0, + PB_STATUS_TEMP_BASE + page, + PB_TEMP_UT_WARNING); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, page, + PMBUS_UT_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "temp", "lcrit", + in_index, page, + PMBUS_UT_FAULT_LIMIT, + PSC_TEMPERATURE, true); + if (info->func[page] & PMBUS_HAVE_STATUS_TEMP) { + pmbus_add_boolean_cmp(data, "temp", + "lcrit_alarm", in_index, i1, i0, + PB_STATUS_TEMP_BASE + page, + PB_TEMP_UT_FAULT); + have_alarm = true; + } + } + if (pmbus_check_word_register + (client, page, PMBUS_OT_WARN_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "temp", "max", in_index, + page, PMBUS_OT_WARN_LIMIT, + PSC_TEMPERATURE, true); + if (info->func[page] & PMBUS_HAVE_STATUS_TEMP) { + pmbus_add_boolean_cmp(data, "temp", + "max_alarm", in_index, i0, i1, + PB_STATUS_TEMP_BASE + page, + PB_TEMP_OT_WARNING); + have_alarm = true; + } + } + if (pmbus_check_word_register(client, page, + PMBUS_OT_FAULT_LIMIT)) { + i1 = data->num_sensors; + pmbus_add_sensor(data, "temp", "crit", in_index, + page, PMBUS_OT_FAULT_LIMIT, + PSC_TEMPERATURE, true); + if (info->func[page] & PMBUS_HAVE_STATUS_TEMP) { + pmbus_add_boolean_cmp(data, "temp", + "crit_alarm", in_index, i0, i1, + PB_STATUS_TEMP_BASE + page, + PB_TEMP_OT_FAULT); + have_alarm = true; + } + } + /* + * Last resort - we were not able to create any alarm + * registers. Report alarm for all sensors using the + * status register temperature alarm bit. + */ + if (!have_alarm) + pmbus_add_boolean_reg(data, "temp", "alarm", + in_index, + PB_STATUS_BASE + page, + PB_STATUS_TEMPERATURE); + in_index++; + } + } + + /* + * Fans + */ + in_index = 1; + for (page = 0; page < info->pages; page++) { + int f; + + for (f = 0; f < ARRAY_SIZE(pmbus_fan_registers); f++) { + int regval; + + if (!(info->func[page] & pmbus_fan_flags[f])) + break; + + if (!pmbus_check_word_register(client, page, + pmbus_fan_registers[f]) + || !pmbus_check_byte_register(client, page, + pmbus_fan_config_registers[f])) + break; + + /* + * Skip fan if not installed. + * Each fan configuration register covers multiple fans, + * so we have to do some magic. + */ + regval = pmbus_read_byte_data(client, page, + pmbus_fan_config_registers[f]); + if (regval < 0 || + (!(regval & (PB_FAN_1_INSTALLED >> ((f & 1) * 4))))) + continue; + + i0 = data->num_sensors; + pmbus_add_sensor(data, "fan", "input", in_index, page, + pmbus_fan_registers[f], PSC_FAN, true); + + /* + * Each fan status register covers multiple fans, + * so we have to do some magic. + */ + if ((info->func[page] & pmbus_fan_status_flags[f]) && + pmbus_check_byte_register(client, + page, pmbus_fan_status_registers[f])) { + int base; + + if (f > 1) /* fan 3, 4 */ + base = PB_STATUS_FAN34_BASE + page; + else + base = PB_STATUS_FAN_BASE + page; + pmbus_add_boolean_reg(data, "fan", "alarm", + in_index, base, + PB_FAN_FAN1_WARNING >> (f & 1)); + pmbus_add_boolean_reg(data, "fan", "fault", + in_index, base, + PB_FAN_FAN1_FAULT >> (f & 1)); + } + in_index++; + } + } +} + +/* + * Identify chip parameters. + * This function is called for all chips. + */ +static int pmbus_identify_common(struct i2c_client *client, + struct pmbus_data *data) +{ + int vout_mode = -1, exponent; + + if (pmbus_check_byte_register(client, 0, PMBUS_VOUT_MODE)) + vout_mode = pmbus_read_byte_data(client, 0, PMBUS_VOUT_MODE); + if (vout_mode >= 0 && vout_mode != 0xff) { + /* + * Not all chips support the VOUT_MODE command, + * so a failure to read it is not an error. + */ + switch (vout_mode >> 5) { + case 0: /* linear mode */ + if (data->info->direct[PSC_VOLTAGE_OUT]) + return -ENODEV; + + exponent = vout_mode & 0x1f; + /* and sign-extend it */ + if (exponent & 0x10) + exponent |= ~0x1f; + data->exponent = exponent; + break; + case 2: /* direct mode */ + if (!data->info->direct[PSC_VOLTAGE_OUT]) + return -ENODEV; + break; + default: + return -ENODEV; + } + } + + /* Determine maximum number of sensors, booleans, and labels */ + pmbus_find_max_attr(client, data); + pmbus_clear_fault_page(client, 0); + return 0; +} + +int pmbus_do_probe(struct i2c_client *client, const struct i2c_device_id *id, + struct pmbus_driver_info *info) +{ + const struct pmbus_platform_data *pdata = client->dev.platform_data; + struct pmbus_data *data; + int ret; + + if (!info) { + dev_err(&client->dev, "Missing chip information"); + return -ENODEV; + } + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WRITE_BYTE + | I2C_FUNC_SMBUS_BYTE_DATA + | I2C_FUNC_SMBUS_WORD_DATA)) + return -ENODEV; + + data = kzalloc(sizeof(*data), GFP_KERNEL); + if (!data) { + dev_err(&client->dev, "No memory to allocate driver data\n"); + return -ENOMEM; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + + /* + * Bail out if status register or PMBus revision register + * does not exist. + */ + if (i2c_smbus_read_byte_data(client, PMBUS_STATUS_BYTE) < 0 + || i2c_smbus_read_byte_data(client, PMBUS_REVISION) < 0) { + dev_err(&client->dev, + "Status or revision register not found\n"); + ret = -ENODEV; + goto out_data; + } + + if (pdata) + data->flags = pdata->flags; + data->info = info; + + pmbus_clear_faults(client); + + if (info->identify) { + ret = (*info->identify)(client, info); + if (ret < 0) { + dev_err(&client->dev, "Chip identification failed\n"); + goto out_data; + } + } + + if (info->pages <= 0 || info->pages > PMBUS_PAGES) { + dev_err(&client->dev, "Bad number of PMBus pages: %d\n", + info->pages); + ret = -EINVAL; + goto out_data; + } + /* + * Bail out if more than one page was configured, but we can not + * select the highest page. This is an indication that the wrong + * chip type was selected. Better bail out now than keep + * returning errors later on. + */ + if (info->pages > 1 && pmbus_set_page(client, info->pages - 1) < 0) { + dev_err(&client->dev, "Failed to select page %d\n", + info->pages - 1); + ret = -EINVAL; + goto out_data; + } + + ret = pmbus_identify_common(client, data); + if (ret < 0) { + dev_err(&client->dev, "Failed to identify chip capabilities\n"); + goto out_data; + } + + ret = -ENOMEM; + data->sensors = kzalloc(sizeof(struct pmbus_sensor) * data->max_sensors, + GFP_KERNEL); + if (!data->sensors) { + dev_err(&client->dev, "No memory to allocate sensor data\n"); + goto out_data; + } + + data->booleans = kzalloc(sizeof(struct pmbus_boolean) + * data->max_booleans, GFP_KERNEL); + if (!data->booleans) { + dev_err(&client->dev, "No memory to allocate boolean data\n"); + goto out_sensors; + } + + data->labels = kzalloc(sizeof(struct pmbus_label) * data->max_labels, + GFP_KERNEL); + if (!data->labels) { + dev_err(&client->dev, "No memory to allocate label data\n"); + goto out_booleans; + } + + data->attributes = kzalloc(sizeof(struct attribute *) + * data->max_attributes, GFP_KERNEL); + if (!data->attributes) { + dev_err(&client->dev, "No memory to allocate attribute data\n"); + goto out_labels; + } + + pmbus_find_attributes(client, data); + + /* + * If there are no attributes, something is wrong. + * Bail out instead of trying to register nothing. + */ + if (!data->num_attributes) { + dev_err(&client->dev, "No attributes found\n"); + ret = -ENODEV; + goto out_attributes; + } + + /* Register sysfs hooks */ + data->group.attrs = data->attributes; + ret = sysfs_create_group(&client->dev.kobj, &data->group); + if (ret) { + dev_err(&client->dev, "Failed to create sysfs entries\n"); + goto out_attributes; + } + data->hwmon_dev = hwmon_device_register(&client->dev); + if (IS_ERR(data->hwmon_dev)) { + ret = PTR_ERR(data->hwmon_dev); + dev_err(&client->dev, "Failed to register hwmon device\n"); + goto out_hwmon_device_register; + } + return 0; + +out_hwmon_device_register: + sysfs_remove_group(&client->dev.kobj, &data->group); +out_attributes: + kfree(data->attributes); +out_labels: + kfree(data->labels); +out_booleans: + kfree(data->booleans); +out_sensors: + kfree(data->sensors); +out_data: + kfree(data); + return ret; +} +EXPORT_SYMBOL_GPL(pmbus_do_probe); + +int pmbus_do_remove(struct i2c_client *client) +{ + struct pmbus_data *data = i2c_get_clientdata(client); + hwmon_device_unregister(data->hwmon_dev); + sysfs_remove_group(&client->dev.kobj, &data->group); + kfree(data->attributes); + kfree(data->labels); + kfree(data->booleans); + kfree(data->sensors); + kfree(data); + return 0; +} +EXPORT_SYMBOL_GPL(pmbus_do_remove); + +MODULE_AUTHOR("Guenter Roeck"); +MODULE_DESCRIPTION("PMBus core driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/hwmon/w83627ehf.c b/drivers/hwmon/w83627ehf.c index 073eabedc43..f2b377c56a3 100644 --- a/drivers/hwmon/w83627ehf.c +++ b/drivers/hwmon/w83627ehf.c @@ -1,11 +1,12 @@ /* w83627ehf - Driver for the hardware monitoring functionality of - the Winbond W83627EHF Super-I/O chip + the Winbond W83627EHF Super-I/O chip Copyright (C) 2005 Jean Delvare <khali@linux-fr.org> Copyright (C) 2006 Yuan Mu (Winbond), - Rudolf Marek <r.marek@assembler.cz> - David Hubbard <david.c.hubbard@gmail.com> + Rudolf Marek <r.marek@assembler.cz> + David Hubbard <david.c.hubbard@gmail.com> Daniel J Blueman <daniel.blueman@gmail.com> + Copyright (C) 2010 Sheng-Yuan Huang (Nuvoton) (PS00) Shamelessly ripped from the w83627hf driver Copyright (C) 2003 Mark Studebaker @@ -35,11 +36,13 @@ Chip #vin #fan #pwm #temp chip IDs man ID w83627ehf 10 5 4 3 0x8850 0x88 0x5ca3 - 0x8860 0xa1 + 0x8860 0xa1 w83627dhg 9 5 4 3 0xa020 0xc1 0x5ca3 w83627dhg-p 9 5 4 3 0xb070 0xc1 0x5ca3 w83667hg 9 5 3 3 0xa510 0xc1 0x5ca3 - w83667hg-b 9 5 3 3 0xb350 0xc1 0x5ca3 + w83667hg-b 9 5 3 4 0xb350 0xc1 0x5ca3 + nct6775f 9 4 3 9 0xb470 0xc1 0x5ca3 + nct6776f 9 5 3 9 0xC330 0xc1 0x5ca3 */ #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt @@ -58,21 +61,28 @@ #include <linux/io.h> #include "lm75.h" -enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg, w83667hg_b }; +enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg, w83667hg_b, nct6775, + nct6776 }; /* used to set data->name = w83627ehf_device_names[data->sio_kind] */ -static const char * w83627ehf_device_names[] = { +static const char * const w83627ehf_device_names[] = { "w83627ehf", "w83627dhg", "w83627dhg", "w83667hg", "w83667hg", + "nct6775", + "nct6776", }; static unsigned short force_id; module_param(force_id, ushort, 0); MODULE_PARM_DESC(force_id, "Override the detected device ID"); +static unsigned short fan_debounce; +module_param(fan_debounce, ushort, 0); +MODULE_PARM_DESC(fan_debounce, "Enable debouncing for fan RPM signal"); + #define DRVNAME "w83627ehf" /* @@ -80,7 +90,7 @@ MODULE_PARM_DESC(force_id, "Override the detected device ID"); */ #define W83627EHF_LD_HWM 0x0b -#define W83667HG_LD_VID 0x0d +#define W83667HG_LD_VID 0x0d #define SIO_REG_LDSEL 0x07 /* Logical device select */ #define SIO_REG_DEVID 0x20 /* Device ID (2 bytes) */ @@ -94,8 +104,10 @@ MODULE_PARM_DESC(force_id, "Override the detected device ID"); #define SIO_W83627EHG_ID 0x8860 #define SIO_W83627DHG_ID 0xa020 #define SIO_W83627DHG_P_ID 0xb070 -#define SIO_W83667HG_ID 0xa510 +#define SIO_W83667HG_ID 0xa510 #define SIO_W83667HG_B_ID 0xb350 +#define SIO_NCT6775_ID 0xb470 +#define SIO_NCT6776_ID 0xc330 #define SIO_ID_MASK 0xFFF0 static inline void @@ -138,7 +150,7 @@ superio_exit(int ioreg) * ISA constants */ -#define IOREGION_ALIGNMENT ~7 +#define IOREGION_ALIGNMENT (~7) #define IOREGION_OFFSET 5 #define IOREGION_LENGTH 2 #define ADDR_REG_OFFSET 0 @@ -164,13 +176,10 @@ static const u16 W83627EHF_REG_FAN_MIN[] = { 0x3b, 0x3c, 0x3d, 0x3e, 0x55c }; #define W83627EHF_REG_IN(nr) ((nr < 7) ? (0x20 + (nr)) : \ (0x550 + (nr) - 7)) -#define W83627EHF_REG_TEMP1 0x27 -#define W83627EHF_REG_TEMP1_HYST 0x3a -#define W83627EHF_REG_TEMP1_OVER 0x39 -static const u16 W83627EHF_REG_TEMP[] = { 0x150, 0x250 }; -static const u16 W83627EHF_REG_TEMP_HYST[] = { 0x153, 0x253 }; -static const u16 W83627EHF_REG_TEMP_OVER[] = { 0x155, 0x255 }; -static const u16 W83627EHF_REG_TEMP_CONFIG[] = { 0x152, 0x252 }; +static const u16 W83627EHF_REG_TEMP[] = { 0x27, 0x150, 0x250, 0x7e }; +static const u16 W83627EHF_REG_TEMP_HYST[] = { 0x3a, 0x153, 0x253, 0 }; +static const u16 W83627EHF_REG_TEMP_OVER[] = { 0x39, 0x155, 0x255, 0 }; +static const u16 W83627EHF_REG_TEMP_CONFIG[] = { 0, 0x152, 0x252, 0 }; /* Fan clock dividers are spread over the following five registers */ #define W83627EHF_REG_FANDIV1 0x47 @@ -179,6 +188,11 @@ static const u16 W83627EHF_REG_TEMP_CONFIG[] = { 0x152, 0x252 }; #define W83627EHF_REG_DIODE 0x59 #define W83627EHF_REG_SMI_OVT 0x4C +/* NCT6775F has its own fan divider registers */ +#define NCT6775_REG_FANDIV1 0x506 +#define NCT6775_REG_FANDIV2 0x507 +#define NCT6775_REG_FAN_DEBOUNCE 0xf0 + #define W83627EHF_REG_ALARM1 0x459 #define W83627EHF_REG_ALARM2 0x45A #define W83627EHF_REG_ALARM3 0x45B @@ -199,22 +213,123 @@ static const u8 W83627EHF_PWM_MODE_SHIFT[] = { 0, 1, 0, 6 }; static const u8 W83627EHF_PWM_ENABLE_SHIFT[] = { 2, 4, 1, 4 }; /* FAN Duty Cycle, be used to control */ -static const u8 W83627EHF_REG_PWM[] = { 0x01, 0x03, 0x11, 0x61 }; -static const u8 W83627EHF_REG_TARGET[] = { 0x05, 0x06, 0x13, 0x63 }; +static const u16 W83627EHF_REG_PWM[] = { 0x01, 0x03, 0x11, 0x61 }; +static const u16 W83627EHF_REG_TARGET[] = { 0x05, 0x06, 0x13, 0x63 }; static const u8 W83627EHF_REG_TOLERANCE[] = { 0x07, 0x07, 0x14, 0x62 }; /* Advanced Fan control, some values are common for all fans */ -static const u8 W83627EHF_REG_FAN_START_OUTPUT[] = { 0x0a, 0x0b, 0x16, 0x65 }; -static const u8 W83627EHF_REG_FAN_STOP_OUTPUT[] = { 0x08, 0x09, 0x15, 0x64 }; -static const u8 W83627EHF_REG_FAN_STOP_TIME[] = { 0x0c, 0x0d, 0x17, 0x66 }; +static const u16 W83627EHF_REG_FAN_START_OUTPUT[] = { 0x0a, 0x0b, 0x16, 0x65 }; +static const u16 W83627EHF_REG_FAN_STOP_OUTPUT[] = { 0x08, 0x09, 0x15, 0x64 }; +static const u16 W83627EHF_REG_FAN_STOP_TIME[] = { 0x0c, 0x0d, 0x17, 0x66 }; -static const u8 W83627EHF_REG_FAN_MAX_OUTPUT_COMMON[] +static const u16 W83627EHF_REG_FAN_MAX_OUTPUT_COMMON[] = { 0xff, 0x67, 0xff, 0x69 }; -static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_COMMON[] +static const u16 W83627EHF_REG_FAN_STEP_OUTPUT_COMMON[] = { 0xff, 0x68, 0xff, 0x6a }; -static const u8 W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B[] = { 0x67, 0x69, 0x6b }; -static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B[] = { 0x68, 0x6a, 0x6c }; +static const u16 W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B[] = { 0x67, 0x69, 0x6b }; +static const u16 W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B[] + = { 0x68, 0x6a, 0x6c }; + +static const u16 NCT6775_REG_TARGET[] = { 0x101, 0x201, 0x301 }; +static const u16 NCT6775_REG_FAN_MODE[] = { 0x102, 0x202, 0x302 }; +static const u16 NCT6775_REG_FAN_STOP_OUTPUT[] = { 0x105, 0x205, 0x305 }; +static const u16 NCT6775_REG_FAN_START_OUTPUT[] = { 0x106, 0x206, 0x306 }; +static const u16 NCT6775_REG_FAN_STOP_TIME[] = { 0x107, 0x207, 0x307 }; +static const u16 NCT6775_REG_PWM[] = { 0x109, 0x209, 0x309 }; +static const u16 NCT6775_REG_FAN_MAX_OUTPUT[] = { 0x10a, 0x20a, 0x30a }; +static const u16 NCT6775_REG_FAN_STEP_OUTPUT[] = { 0x10b, 0x20b, 0x30b }; +static const u16 NCT6775_REG_FAN[] = { 0x630, 0x632, 0x634, 0x636, 0x638 }; +static const u16 NCT6776_REG_FAN_MIN[] = { 0x63a, 0x63c, 0x63e, 0x640, 0x642}; + +static const u16 NCT6775_REG_TEMP[] + = { 0x27, 0x150, 0x250, 0x73, 0x75, 0x77, 0x62b, 0x62c, 0x62d }; +static const u16 NCT6775_REG_TEMP_CONFIG[] + = { 0, 0x152, 0x252, 0, 0, 0, 0x628, 0x629, 0x62A }; +static const u16 NCT6775_REG_TEMP_HYST[] + = { 0x3a, 0x153, 0x253, 0, 0, 0, 0x673, 0x678, 0x67D }; +static const u16 NCT6775_REG_TEMP_OVER[] + = { 0x39, 0x155, 0x255, 0, 0, 0, 0x672, 0x677, 0x67C }; +static const u16 NCT6775_REG_TEMP_SOURCE[] + = { 0x621, 0x622, 0x623, 0x100, 0x200, 0x300, 0x624, 0x625, 0x626 }; + +static const char *const w83667hg_b_temp_label[] = { + "SYSTIN", + "CPUTIN", + "AUXTIN", + "AMDTSI", + "PECI Agent 1", + "PECI Agent 2", + "PECI Agent 3", + "PECI Agent 4" +}; + +static const char *const nct6775_temp_label[] = { + "", + "SYSTIN", + "CPUTIN", + "AUXTIN", + "AMD SB-TSI", + "PECI Agent 0", + "PECI Agent 1", + "PECI Agent 2", + "PECI Agent 3", + "PECI Agent 4", + "PECI Agent 5", + "PECI Agent 6", + "PECI Agent 7", + "PCH_CHIP_CPU_MAX_TEMP", + "PCH_CHIP_TEMP", + "PCH_CPU_TEMP", + "PCH_MCH_TEMP", + "PCH_DIM0_TEMP", + "PCH_DIM1_TEMP", + "PCH_DIM2_TEMP", + "PCH_DIM3_TEMP" +}; + +static const char *const nct6776_temp_label[] = { + "", + "SYSTIN", + "CPUTIN", + "AUXTIN", + "SMBUSMASTER 0", + "SMBUSMASTER 1", + "SMBUSMASTER 2", + "SMBUSMASTER 3", + "SMBUSMASTER 4", + "SMBUSMASTER 5", + "SMBUSMASTER 6", + "SMBUSMASTER 7", + "PECI Agent 0", + "PECI Agent 1", + "PCH_CHIP_CPU_MAX_TEMP", + "PCH_CHIP_TEMP", + "PCH_CPU_TEMP", + "PCH_MCH_TEMP", + "PCH_DIM0_TEMP", + "PCH_DIM1_TEMP", + "PCH_DIM2_TEMP", + "PCH_DIM3_TEMP", + "BYTE_TEMP" +}; + +#define NUM_REG_TEMP ARRAY_SIZE(NCT6775_REG_TEMP) + +static inline int is_word_sized(u16 reg) +{ + return ((((reg & 0xff00) == 0x100 + || (reg & 0xff00) == 0x200) + && ((reg & 0x00ff) == 0x50 + || (reg & 0x00ff) == 0x53 + || (reg & 0x00ff) == 0x55)) + || (reg & 0xfff0) == 0x630 + || reg == 0x640 || reg == 0x642 + || ((reg & 0xfff0) == 0x650 + && (reg & 0x000f) >= 0x06) + || reg == 0x73 || reg == 0x75 || reg == 0x77 + ); +} /* * Conversions @@ -232,12 +347,36 @@ static inline u8 step_time_to_reg(unsigned int msec, u8 mode) (msec + 200) / 400), 1, 255); } -static inline unsigned int -fan_from_reg(u8 reg, unsigned int div) +static unsigned int fan_from_reg8(u16 reg, unsigned int divreg) { if (reg == 0 || reg == 255) return 0; - return 1350000U / (reg * div); + return 1350000U / (reg << divreg); +} + +static unsigned int fan_from_reg13(u16 reg, unsigned int divreg) +{ + if ((reg & 0xff1f) == 0xff1f) + return 0; + + reg = (reg & 0x1f) | ((reg & 0xff00) >> 3); + + if (reg == 0) + return 0; + + return 1350000U / reg; +} + +static unsigned int fan_from_reg16(u16 reg, unsigned int divreg) +{ + if (reg == 0 || reg == 0xffff) + return 0; + + /* + * Even though the registers are 16 bit wide, the fan divisor + * still applies. + */ + return 1350000U / (reg << divreg); } static inline unsigned int @@ -247,21 +386,19 @@ div_from_reg(u8 reg) } static inline int -temp1_from_reg(s8 reg) +temp_from_reg(u16 reg, s16 regval) { - return reg * 1000; + if (is_word_sized(reg)) + return LM75_TEMP_FROM_REG(regval); + return regval * 1000; } -static inline s8 -temp1_to_reg(long temp, int min, int max) +static inline u16 +temp_to_reg(u16 reg, long temp) { - if (temp <= min) - return min / 1000; - if (temp >= max) - return max / 1000; - if (temp < 0) - return (temp - 500) / 1000; - return (temp + 500) / 1000; + if (is_word_sized(reg)) + return LM75_TEMP_TO_REG(temp); + return DIV_ROUND_CLOSEST(SENSORS_LIMIT(temp, -127000, 128000), 1000); } /* Some of analog inputs have internal scaling (2x), 8mV is ADC LSB */ @@ -275,7 +412,8 @@ static inline long in_from_reg(u8 reg, u8 nr) static inline u8 in_to_reg(u32 val, u8 nr) { - return SENSORS_LIMIT(((val + (scale_in[nr] / 2)) / scale_in[nr]), 0, 255); + return SENSORS_LIMIT(((val + (scale_in[nr] / 2)) / scale_in[nr]), 0, + 255); } /* @@ -289,38 +427,57 @@ struct w83627ehf_data { struct device *hwmon_dev; struct mutex lock; - const u8 *REG_FAN_START_OUTPUT; - const u8 *REG_FAN_STOP_OUTPUT; - const u8 *REG_FAN_MAX_OUTPUT; - const u8 *REG_FAN_STEP_OUTPUT; + u16 reg_temp[NUM_REG_TEMP]; + u16 reg_temp_over[NUM_REG_TEMP]; + u16 reg_temp_hyst[NUM_REG_TEMP]; + u16 reg_temp_config[NUM_REG_TEMP]; + u8 temp_src[NUM_REG_TEMP]; + const char * const *temp_label; + + const u16 *REG_PWM; + const u16 *REG_TARGET; + const u16 *REG_FAN; + const u16 *REG_FAN_MIN; + const u16 *REG_FAN_START_OUTPUT; + const u16 *REG_FAN_STOP_OUTPUT; + const u16 *REG_FAN_STOP_TIME; + const u16 *REG_FAN_MAX_OUTPUT; + const u16 *REG_FAN_STEP_OUTPUT; + + unsigned int (*fan_from_reg)(u16 reg, unsigned int divreg); + unsigned int (*fan_from_reg_min)(u16 reg, unsigned int divreg); struct mutex update_lock; char valid; /* !=0 if following fields are valid */ unsigned long last_updated; /* In jiffies */ /* Register values */ + u8 bank; /* current register bank */ u8 in_num; /* number of in inputs we have */ u8 in[10]; /* Register value */ u8 in_max[10]; /* Register value */ u8 in_min[10]; /* Register value */ - u8 fan[5]; - u8 fan_min[5]; + unsigned int rpm[5]; + u16 fan_min[5]; u8 fan_div[5]; u8 has_fan; /* some fan inputs can be disabled */ + u8 has_fan_min; /* some fans don't have min register */ + bool has_fan_div; u8 temp_type[3]; - s8 temp1; - s8 temp1_max; - s8 temp1_max_hyst; - s16 temp[2]; - s16 temp_max[2]; - s16 temp_max_hyst[2]; + s16 temp[9]; + s16 temp_max[9]; + s16 temp_max_hyst[9]; u32 alarms; u8 pwm_mode[4]; /* 0->DC variable voltage, 1->PWM variable duty cycle */ u8 pwm_enable[4]; /* 1->manual 2->thermal cruise mode (also called SmartFan I) 3->fan speed cruise mode - 4->variable thermal cruise (also called SmartFan III) */ + 4->variable thermal cruise (also called + SmartFan III) + 5->enhanced variable thermal cruise (also called + SmartFan IV) */ + u8 pwm_enable_orig[4]; /* original value of pwm_enable */ u8 pwm_num; /* number of pwm */ u8 pwm[4]; u8 target_temp[4]; @@ -335,7 +492,7 @@ struct w83627ehf_data { u8 vid; u8 vrm; - u8 temp3_disable; + u16 have_temp; u8 in6_skip; }; @@ -344,30 +501,19 @@ struct w83627ehf_sio_data { enum kinds kind; }; -static inline int is_word_sized(u16 reg) -{ - return (((reg & 0xff00) == 0x100 - || (reg & 0xff00) == 0x200) - && ((reg & 0x00ff) == 0x50 - || (reg & 0x00ff) == 0x53 - || (reg & 0x00ff) == 0x55)); -} - -/* Registers 0x50-0x5f are banked */ +/* + * On older chips, only registers 0x50-0x5f are banked. + * On more recent chips, all registers are banked. + * Assume that is the case and set the bank number for each access. + * Cache the bank number so it only needs to be set if it changes. + */ static inline void w83627ehf_set_bank(struct w83627ehf_data *data, u16 reg) { - if ((reg & 0x00f0) == 0x50) { + u8 bank = reg >> 8; + if (data->bank != bank) { outb_p(W83627EHF_REG_BANK, data->addr + ADDR_REG_OFFSET); - outb_p(reg >> 8, data->addr + DATA_REG_OFFSET); - } -} - -/* Not strictly necessary, but play it safe for now */ -static inline void w83627ehf_reset_bank(struct w83627ehf_data *data, u16 reg) -{ - if (reg & 0xff00) { - outb_p(W83627EHF_REG_BANK, data->addr + ADDR_REG_OFFSET); - outb_p(0, data->addr + DATA_REG_OFFSET); + outb_p(bank, data->addr + DATA_REG_OFFSET); + data->bank = bank; } } @@ -385,14 +531,13 @@ static u16 w83627ehf_read_value(struct w83627ehf_data *data, u16 reg) data->addr + ADDR_REG_OFFSET); res = (res << 8) + inb_p(data->addr + DATA_REG_OFFSET); } - w83627ehf_reset_bank(data, reg); mutex_unlock(&data->lock); - return res; } -static int w83627ehf_write_value(struct w83627ehf_data *data, u16 reg, u16 value) +static int w83627ehf_write_value(struct w83627ehf_data *data, u16 reg, + u16 value) { int word_sized = is_word_sized(reg); @@ -406,13 +551,40 @@ static int w83627ehf_write_value(struct w83627ehf_data *data, u16 reg, u16 value data->addr + ADDR_REG_OFFSET); } outb_p(value & 0xff, data->addr + DATA_REG_OFFSET); - w83627ehf_reset_bank(data, reg); mutex_unlock(&data->lock); return 0; } /* This function assumes that the caller holds data->update_lock */ +static void nct6775_write_fan_div(struct w83627ehf_data *data, int nr) +{ + u8 reg; + + switch (nr) { + case 0: + reg = (w83627ehf_read_value(data, NCT6775_REG_FANDIV1) & 0x70) + | (data->fan_div[0] & 0x7); + w83627ehf_write_value(data, NCT6775_REG_FANDIV1, reg); + break; + case 1: + reg = (w83627ehf_read_value(data, NCT6775_REG_FANDIV1) & 0x7) + | ((data->fan_div[1] << 4) & 0x70); + w83627ehf_write_value(data, NCT6775_REG_FANDIV1, reg); + case 2: + reg = (w83627ehf_read_value(data, NCT6775_REG_FANDIV2) & 0x70) + | (data->fan_div[2] & 0x7); + w83627ehf_write_value(data, NCT6775_REG_FANDIV2, reg); + break; + case 3: + reg = (w83627ehf_read_value(data, NCT6775_REG_FANDIV2) & 0x7) + | ((data->fan_div[3] << 4) & 0x70); + w83627ehf_write_value(data, NCT6775_REG_FANDIV2, reg); + break; + } +} + +/* This function assumes that the caller holds data->update_lock */ static void w83627ehf_write_fan_div(struct w83627ehf_data *data, int nr) { u8 reg; @@ -463,6 +635,32 @@ static void w83627ehf_write_fan_div(struct w83627ehf_data *data, int nr) } } +static void w83627ehf_write_fan_div_common(struct device *dev, + struct w83627ehf_data *data, int nr) +{ + struct w83627ehf_sio_data *sio_data = dev->platform_data; + + if (sio_data->kind == nct6776) + ; /* no dividers, do nothing */ + else if (sio_data->kind == nct6775) + nct6775_write_fan_div(data, nr); + else + w83627ehf_write_fan_div(data, nr); +} + +static void nct6775_update_fan_div(struct w83627ehf_data *data) +{ + u8 i; + + i = w83627ehf_read_value(data, NCT6775_REG_FANDIV1); + data->fan_div[0] = i & 0x7; + data->fan_div[1] = (i & 0x70) >> 4; + i = w83627ehf_read_value(data, NCT6775_REG_FANDIV2); + data->fan_div[2] = i & 0x7; + if (data->has_fan & (1<<3)) + data->fan_div[3] = (i & 0x70) >> 4; +} + static void w83627ehf_update_fan_div(struct w83627ehf_data *data) { int i; @@ -488,10 +686,79 @@ static void w83627ehf_update_fan_div(struct w83627ehf_data *data) } } +static void w83627ehf_update_fan_div_common(struct device *dev, + struct w83627ehf_data *data) +{ + struct w83627ehf_sio_data *sio_data = dev->platform_data; + + if (sio_data->kind == nct6776) + ; /* no dividers, do nothing */ + else if (sio_data->kind == nct6775) + nct6775_update_fan_div(data); + else + w83627ehf_update_fan_div(data); +} + +static void nct6775_update_pwm(struct w83627ehf_data *data) +{ + int i; + int pwmcfg, fanmodecfg; + + for (i = 0; i < data->pwm_num; i++) { + pwmcfg = w83627ehf_read_value(data, + W83627EHF_REG_PWM_ENABLE[i]); + fanmodecfg = w83627ehf_read_value(data, + NCT6775_REG_FAN_MODE[i]); + data->pwm_mode[i] = + ((pwmcfg >> W83627EHF_PWM_MODE_SHIFT[i]) & 1) ? 0 : 1; + data->pwm_enable[i] = ((fanmodecfg >> 4) & 7) + 1; + data->tolerance[i] = fanmodecfg & 0x0f; + data->pwm[i] = w83627ehf_read_value(data, data->REG_PWM[i]); + } +} + +static void w83627ehf_update_pwm(struct w83627ehf_data *data) +{ + int i; + int pwmcfg = 0, tolerance = 0; /* shut up the compiler */ + + for (i = 0; i < data->pwm_num; i++) { + if (!(data->has_fan & (1 << i))) + continue; + + /* pwmcfg, tolerance mapped for i=0, i=1 to same reg */ + if (i != 1) { + pwmcfg = w83627ehf_read_value(data, + W83627EHF_REG_PWM_ENABLE[i]); + tolerance = w83627ehf_read_value(data, + W83627EHF_REG_TOLERANCE[i]); + } + data->pwm_mode[i] = + ((pwmcfg >> W83627EHF_PWM_MODE_SHIFT[i]) & 1) ? 0 : 1; + data->pwm_enable[i] = ((pwmcfg >> W83627EHF_PWM_ENABLE_SHIFT[i]) + & 3) + 1; + data->pwm[i] = w83627ehf_read_value(data, data->REG_PWM[i]); + + data->tolerance[i] = (tolerance >> (i == 1 ? 4 : 0)) & 0x0f; + } +} + +static void w83627ehf_update_pwm_common(struct device *dev, + struct w83627ehf_data *data) +{ + struct w83627ehf_sio_data *sio_data = dev->platform_data; + + if (sio_data->kind == nct6775 || sio_data->kind == nct6776) + nct6775_update_pwm(data); + else + w83627ehf_update_pwm(data); +} + static struct w83627ehf_data *w83627ehf_update_device(struct device *dev) { struct w83627ehf_data *data = dev_get_drvdata(dev); - int pwmcfg = 0, tolerance = 0; /* shut up the compiler */ + struct w83627ehf_sio_data *sio_data = dev->platform_data; + int i; mutex_lock(&data->update_lock); @@ -499,7 +766,7 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev) if (time_after(jiffies, data->last_updated + HZ + HZ/2) || !data->valid) { /* Fan clock dividers */ - w83627ehf_update_fan_div(data); + w83627ehf_update_fan_div_common(dev, data); /* Measured voltages and limits */ for (i = 0; i < data->in_num; i++) { @@ -513,92 +780,90 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev) /* Measured fan speeds and limits */ for (i = 0; i < 5; i++) { + u16 reg; + if (!(data->has_fan & (1 << i))) continue; - data->fan[i] = w83627ehf_read_value(data, - W83627EHF_REG_FAN[i]); - data->fan_min[i] = w83627ehf_read_value(data, - W83627EHF_REG_FAN_MIN[i]); + reg = w83627ehf_read_value(data, data->REG_FAN[i]); + data->rpm[i] = data->fan_from_reg(reg, + data->fan_div[i]); + + if (data->has_fan_min & (1 << i)) + data->fan_min[i] = w83627ehf_read_value(data, + data->REG_FAN_MIN[i]); /* If we failed to measure the fan speed and clock divider can be increased, let's try that for next time */ - if (data->fan[i] == 0xff - && data->fan_div[i] < 0x07) { - dev_dbg(dev, "Increasing fan%d " + if (data->has_fan_div + && (reg >= 0xff || (sio_data->kind == nct6775 + && reg == 0x00)) + && data->fan_div[i] < 0x07) { + dev_dbg(dev, "Increasing fan%d " "clock divider from %u to %u\n", i + 1, div_from_reg(data->fan_div[i]), div_from_reg(data->fan_div[i] + 1)); data->fan_div[i]++; - w83627ehf_write_fan_div(data, i); + w83627ehf_write_fan_div_common(dev, data, i); /* Preserve min limit if possible */ - if (data->fan_min[i] >= 2 + if ((data->has_fan_min & (1 << i)) + && data->fan_min[i] >= 2 && data->fan_min[i] != 255) w83627ehf_write_value(data, - W83627EHF_REG_FAN_MIN[i], + data->REG_FAN_MIN[i], (data->fan_min[i] /= 2)); } } + w83627ehf_update_pwm_common(dev, data); + for (i = 0; i < data->pwm_num; i++) { if (!(data->has_fan & (1 << i))) continue; - /* pwmcfg, tolerance mapped for i=0, i=1 to same reg */ - if (i != 1) { - pwmcfg = w83627ehf_read_value(data, - W83627EHF_REG_PWM_ENABLE[i]); - tolerance = w83627ehf_read_value(data, - W83627EHF_REG_TOLERANCE[i]); - } - data->pwm_mode[i] = - ((pwmcfg >> W83627EHF_PWM_MODE_SHIFT[i]) & 1) - ? 0 : 1; - data->pwm_enable[i] = - ((pwmcfg >> W83627EHF_PWM_ENABLE_SHIFT[i]) - & 3) + 1; - data->pwm[i] = w83627ehf_read_value(data, - W83627EHF_REG_PWM[i]); - data->fan_start_output[i] = w83627ehf_read_value(data, - W83627EHF_REG_FAN_START_OUTPUT[i]); - data->fan_stop_output[i] = w83627ehf_read_value(data, - W83627EHF_REG_FAN_STOP_OUTPUT[i]); - data->fan_stop_time[i] = w83627ehf_read_value(data, - W83627EHF_REG_FAN_STOP_TIME[i]); - - if (data->REG_FAN_MAX_OUTPUT[i] != 0xff) + data->fan_start_output[i] = + w83627ehf_read_value(data, + data->REG_FAN_START_OUTPUT[i]); + data->fan_stop_output[i] = + w83627ehf_read_value(data, + data->REG_FAN_STOP_OUTPUT[i]); + data->fan_stop_time[i] = + w83627ehf_read_value(data, + data->REG_FAN_STOP_TIME[i]); + + if (data->REG_FAN_MAX_OUTPUT && + data->REG_FAN_MAX_OUTPUT[i] != 0xff) data->fan_max_output[i] = w83627ehf_read_value(data, - data->REG_FAN_MAX_OUTPUT[i]); + data->REG_FAN_MAX_OUTPUT[i]); - if (data->REG_FAN_STEP_OUTPUT[i] != 0xff) + if (data->REG_FAN_STEP_OUTPUT && + data->REG_FAN_STEP_OUTPUT[i] != 0xff) data->fan_step_output[i] = w83627ehf_read_value(data, - data->REG_FAN_STEP_OUTPUT[i]); + data->REG_FAN_STEP_OUTPUT[i]); data->target_temp[i] = w83627ehf_read_value(data, - W83627EHF_REG_TARGET[i]) & + data->REG_TARGET[i]) & (data->pwm_mode[i] == 1 ? 0x7f : 0xff); - data->tolerance[i] = (tolerance >> (i == 1 ? 4 : 0)) - & 0x0f; } /* Measured temperatures and limits */ - data->temp1 = w83627ehf_read_value(data, - W83627EHF_REG_TEMP1); - data->temp1_max = w83627ehf_read_value(data, - W83627EHF_REG_TEMP1_OVER); - data->temp1_max_hyst = w83627ehf_read_value(data, - W83627EHF_REG_TEMP1_HYST); - for (i = 0; i < 2; i++) { + for (i = 0; i < NUM_REG_TEMP; i++) { + if (!(data->have_temp & (1 << i))) + continue; data->temp[i] = w83627ehf_read_value(data, - W83627EHF_REG_TEMP[i]); - data->temp_max[i] = w83627ehf_read_value(data, - W83627EHF_REG_TEMP_OVER[i]); - data->temp_max_hyst[i] = w83627ehf_read_value(data, - W83627EHF_REG_TEMP_HYST[i]); + data->reg_temp[i]); + if (data->reg_temp_over[i]) + data->temp_max[i] + = w83627ehf_read_value(data, + data->reg_temp_over[i]); + if (data->reg_temp_hyst[i]) + data->temp_max_hyst[i] + = w83627ehf_read_value(data, + data->reg_temp_hyst[i]); } data->alarms = w83627ehf_read_value(data, @@ -625,7 +890,8 @@ show_##reg(struct device *dev, struct device_attribute *attr, \ char *buf) \ { \ struct w83627ehf_data *data = w83627ehf_update_device(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ return sprintf(buf, "%ld\n", in_from_reg(data->reg[nr], nr)); \ } @@ -635,14 +901,18 @@ show_in_reg(in_max) #define store_in_reg(REG, reg) \ static ssize_t \ -store_in_##reg (struct device *dev, struct device_attribute *attr, \ - const char *buf, size_t count) \ +store_in_##reg(struct device *dev, struct device_attribute *attr, \ + const char *buf, size_t count) \ { \ struct w83627ehf_data *data = dev_get_drvdata(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ - u32 val = simple_strtoul(buf, NULL, 10); \ - \ + unsigned long val; \ + int err; \ + err = strict_strtoul(buf, 10, &val); \ + if (err < 0) \ + return err; \ mutex_lock(&data->update_lock); \ data->in_##reg[nr] = in_to_reg(val, nr); \ w83627ehf_write_value(data, W83627EHF_REG_IN_##REG(nr), \ @@ -654,7 +924,8 @@ store_in_##reg (struct device *dev, struct device_attribute *attr, \ store_in_reg(MIN, min) store_in_reg(MAX, max) -static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, char *buf) +static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, + char *buf) { struct w83627ehf_data *data = w83627ehf_update_device(dev); struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); @@ -689,45 +960,50 @@ static struct sensor_device_attribute sda_in_alarm[] = { }; static struct sensor_device_attribute sda_in_min[] = { - SENSOR_ATTR(in0_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 0), - SENSOR_ATTR(in1_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 1), - SENSOR_ATTR(in2_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 2), - SENSOR_ATTR(in3_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 3), - SENSOR_ATTR(in4_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 4), - SENSOR_ATTR(in5_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 5), - SENSOR_ATTR(in6_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 6), - SENSOR_ATTR(in7_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 7), - SENSOR_ATTR(in8_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 8), - SENSOR_ATTR(in9_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 9), + SENSOR_ATTR(in0_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 0), + SENSOR_ATTR(in1_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 1), + SENSOR_ATTR(in2_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 2), + SENSOR_ATTR(in3_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 3), + SENSOR_ATTR(in4_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 4), + SENSOR_ATTR(in5_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 5), + SENSOR_ATTR(in6_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 6), + SENSOR_ATTR(in7_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 7), + SENSOR_ATTR(in8_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 8), + SENSOR_ATTR(in9_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 9), }; static struct sensor_device_attribute sda_in_max[] = { - SENSOR_ATTR(in0_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 0), - SENSOR_ATTR(in1_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 1), - SENSOR_ATTR(in2_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 2), - SENSOR_ATTR(in3_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 3), - SENSOR_ATTR(in4_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 4), - SENSOR_ATTR(in5_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 5), - SENSOR_ATTR(in6_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 6), - SENSOR_ATTR(in7_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 7), - SENSOR_ATTR(in8_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 8), - SENSOR_ATTR(in9_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 9), + SENSOR_ATTR(in0_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 0), + SENSOR_ATTR(in1_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 1), + SENSOR_ATTR(in2_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 2), + SENSOR_ATTR(in3_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 3), + SENSOR_ATTR(in4_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 4), + SENSOR_ATTR(in5_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 5), + SENSOR_ATTR(in6_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 6), + SENSOR_ATTR(in7_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 7), + SENSOR_ATTR(in8_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 8), + SENSOR_ATTR(in9_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 9), }; -#define show_fan_reg(reg) \ -static ssize_t \ -show_##reg(struct device *dev, struct device_attribute *attr, \ - char *buf) \ -{ \ - struct w83627ehf_data *data = w83627ehf_update_device(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ - int nr = sensor_attr->index; \ - return sprintf(buf, "%d\n", \ - fan_from_reg(data->reg[nr], \ - div_from_reg(data->fan_div[nr]))); \ +static ssize_t +show_fan(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct w83627ehf_data *data = w83627ehf_update_device(dev); + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + return sprintf(buf, "%d\n", data->rpm[nr]); +} + +static ssize_t +show_fan_min(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct w83627ehf_data *data = w83627ehf_update_device(dev); + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + return sprintf(buf, "%d\n", + data->fan_from_reg_min(data->fan_min[nr], + data->fan_div[nr])); } -show_fan_reg(fan); -show_fan_reg(fan_min); static ssize_t show_fan_div(struct device *dev, struct device_attribute *attr, @@ -746,11 +1022,32 @@ store_fan_min(struct device *dev, struct device_attribute *attr, struct w83627ehf_data *data = dev_get_drvdata(dev); struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); int nr = sensor_attr->index; - unsigned int val = simple_strtoul(buf, NULL, 10); + unsigned long val; + int err; unsigned int reg; u8 new_div; + err = strict_strtoul(buf, 10, &val); + if (err < 0) + return err; + mutex_lock(&data->update_lock); + if (!data->has_fan_div) { + /* + * Only NCT6776F for now, so we know that this is a 13 bit + * register + */ + if (!val) { + val = 0xff1f; + } else { + if (val > 1350000U) + val = 135000U; + val = 1350000U / val; + val = (val & 0x1f) | ((val << 3) & 0xff00); + } + data->fan_min[nr] = val; + goto done; /* Leave fan divider alone */ + } if (!val) { /* No min limit, alarm disabled */ data->fan_min[nr] = 255; @@ -761,15 +1058,17 @@ store_fan_min(struct device *dev, struct device_attribute *attr, even with the highest divider (128) */ data->fan_min[nr] = 254; new_div = 7; /* 128 == (1 << 7) */ - dev_warn(dev, "fan%u low limit %u below minimum %u, set to " - "minimum\n", nr + 1, val, fan_from_reg(254, 128)); + dev_warn(dev, "fan%u low limit %lu below minimum %u, set to " + "minimum\n", nr + 1, val, + data->fan_from_reg_min(254, 7)); } else if (!reg) { /* Speed above this value cannot possibly be represented, even with the lowest divider (1) */ data->fan_min[nr] = 1; new_div = 0; /* 1 == (1 << 0) */ - dev_warn(dev, "fan%u low limit %u above maximum %u, set to " - "maximum\n", nr + 1, val, fan_from_reg(1, 1)); + dev_warn(dev, "fan%u low limit %lu above maximum %u, set to " + "maximum\n", nr + 1, val, + data->fan_from_reg_min(1, 0)); } else { /* Automatically pick the best divider, i.e. the one such that the min limit will correspond to a register value @@ -785,25 +1084,16 @@ store_fan_min(struct device *dev, struct device_attribute *attr, /* Write both the fan clock divider (if it changed) and the new fan min (unconditionally) */ if (new_div != data->fan_div[nr]) { - /* Preserve the fan speed reading */ - if (data->fan[nr] != 0xff) { - if (new_div > data->fan_div[nr]) - data->fan[nr] >>= new_div - data->fan_div[nr]; - else if (data->fan[nr] & 0x80) - data->fan[nr] = 0xff; - else - data->fan[nr] <<= data->fan_div[nr] - new_div; - } - dev_dbg(dev, "fan%u clock divider changed from %u to %u\n", nr + 1, div_from_reg(data->fan_div[nr]), div_from_reg(new_div)); data->fan_div[nr] = new_div; - w83627ehf_write_fan_div(data, nr); + w83627ehf_write_fan_div_common(dev, data, nr); /* Give the chip time to sample a new speed value */ data->last_updated = jiffies; } - w83627ehf_write_value(data, W83627EHF_REG_FAN_MIN[nr], +done: + w83627ehf_write_value(data, data->REG_FAN_MIN[nr], data->fan_min[nr]); mutex_unlock(&data->update_lock); @@ -847,70 +1137,54 @@ static struct sensor_device_attribute sda_fan_div[] = { SENSOR_ATTR(fan5_div, S_IRUGO, show_fan_div, NULL, 4), }; -#define show_temp1_reg(reg) \ -static ssize_t \ -show_##reg(struct device *dev, struct device_attribute *attr, \ - char *buf) \ -{ \ - struct w83627ehf_data *data = w83627ehf_update_device(dev); \ - return sprintf(buf, "%d\n", temp1_from_reg(data->reg)); \ -} -show_temp1_reg(temp1); -show_temp1_reg(temp1_max); -show_temp1_reg(temp1_max_hyst); - -#define store_temp1_reg(REG, reg) \ -static ssize_t \ -store_temp1_##reg(struct device *dev, struct device_attribute *attr, \ - const char *buf, size_t count) \ -{ \ - struct w83627ehf_data *data = dev_get_drvdata(dev); \ - long val = simple_strtol(buf, NULL, 10); \ - \ - mutex_lock(&data->update_lock); \ - data->temp1_##reg = temp1_to_reg(val, -128000, 127000); \ - w83627ehf_write_value(data, W83627EHF_REG_TEMP1_##REG, \ - data->temp1_##reg); \ - mutex_unlock(&data->update_lock); \ - return count; \ +static ssize_t +show_temp_label(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct w83627ehf_data *data = w83627ehf_update_device(dev); + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + return sprintf(buf, "%s\n", data->temp_label[data->temp_src[nr]]); } -store_temp1_reg(OVER, max); -store_temp1_reg(HYST, max_hyst); -#define show_temp_reg(reg) \ +#define show_temp_reg(addr, reg) \ static ssize_t \ show_##reg(struct device *dev, struct device_attribute *attr, \ char *buf) \ { \ struct w83627ehf_data *data = w83627ehf_update_device(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ return sprintf(buf, "%d\n", \ - LM75_TEMP_FROM_REG(data->reg[nr])); \ + temp_from_reg(data->addr[nr], data->reg[nr])); \ } -show_temp_reg(temp); -show_temp_reg(temp_max); -show_temp_reg(temp_max_hyst); +show_temp_reg(reg_temp, temp); +show_temp_reg(reg_temp_over, temp_max); +show_temp_reg(reg_temp_hyst, temp_max_hyst); -#define store_temp_reg(REG, reg) \ +#define store_temp_reg(addr, reg) \ static ssize_t \ store_##reg(struct device *dev, struct device_attribute *attr, \ const char *buf, size_t count) \ { \ struct w83627ehf_data *data = dev_get_drvdata(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ - long val = simple_strtol(buf, NULL, 10); \ - \ + int err; \ + long val; \ + err = strict_strtol(buf, 10, &val); \ + if (err < 0) \ + return err; \ mutex_lock(&data->update_lock); \ - data->reg[nr] = LM75_TEMP_TO_REG(val); \ - w83627ehf_write_value(data, W83627EHF_REG_TEMP_##REG[nr], \ + data->reg[nr] = temp_to_reg(data->addr[nr], val); \ + w83627ehf_write_value(data, data->addr[nr], \ data->reg[nr]); \ mutex_unlock(&data->update_lock); \ return count; \ } -store_temp_reg(OVER, temp_max); -store_temp_reg(HYST, temp_max_hyst); +store_temp_reg(reg_temp_over, temp_max); +store_temp_reg(reg_temp_hyst, temp_max_hyst); static ssize_t show_temp_type(struct device *dev, struct device_attribute *attr, char *buf) @@ -922,27 +1196,69 @@ show_temp_type(struct device *dev, struct device_attribute *attr, char *buf) } static struct sensor_device_attribute sda_temp_input[] = { - SENSOR_ATTR(temp1_input, S_IRUGO, show_temp1, NULL, 0), - SENSOR_ATTR(temp2_input, S_IRUGO, show_temp, NULL, 0), - SENSOR_ATTR(temp3_input, S_IRUGO, show_temp, NULL, 1), + SENSOR_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0), + SENSOR_ATTR(temp2_input, S_IRUGO, show_temp, NULL, 1), + SENSOR_ATTR(temp3_input, S_IRUGO, show_temp, NULL, 2), + SENSOR_ATTR(temp4_input, S_IRUGO, show_temp, NULL, 3), + SENSOR_ATTR(temp5_input, S_IRUGO, show_temp, NULL, 4), + SENSOR_ATTR(temp6_input, S_IRUGO, show_temp, NULL, 5), + SENSOR_ATTR(temp7_input, S_IRUGO, show_temp, NULL, 6), + SENSOR_ATTR(temp8_input, S_IRUGO, show_temp, NULL, 7), + SENSOR_ATTR(temp9_input, S_IRUGO, show_temp, NULL, 8), +}; + +static struct sensor_device_attribute sda_temp_label[] = { + SENSOR_ATTR(temp1_label, S_IRUGO, show_temp_label, NULL, 0), + SENSOR_ATTR(temp2_label, S_IRUGO, show_temp_label, NULL, 1), + SENSOR_ATTR(temp3_label, S_IRUGO, show_temp_label, NULL, 2), + SENSOR_ATTR(temp4_label, S_IRUGO, show_temp_label, NULL, 3), + SENSOR_ATTR(temp5_label, S_IRUGO, show_temp_label, NULL, 4), + SENSOR_ATTR(temp6_label, S_IRUGO, show_temp_label, NULL, 5), + SENSOR_ATTR(temp7_label, S_IRUGO, show_temp_label, NULL, 6), + SENSOR_ATTR(temp8_label, S_IRUGO, show_temp_label, NULL, 7), + SENSOR_ATTR(temp9_label, S_IRUGO, show_temp_label, NULL, 8), }; static struct sensor_device_attribute sda_temp_max[] = { - SENSOR_ATTR(temp1_max, S_IRUGO | S_IWUSR, show_temp1_max, - store_temp1_max, 0), - SENSOR_ATTR(temp2_max, S_IRUGO | S_IWUSR, show_temp_max, + SENSOR_ATTR(temp1_max, S_IRUGO | S_IWUSR, show_temp_max, store_temp_max, 0), - SENSOR_ATTR(temp3_max, S_IRUGO | S_IWUSR, show_temp_max, + SENSOR_ATTR(temp2_max, S_IRUGO | S_IWUSR, show_temp_max, store_temp_max, 1), + SENSOR_ATTR(temp3_max, S_IRUGO | S_IWUSR, show_temp_max, + store_temp_max, 2), + SENSOR_ATTR(temp4_max, S_IRUGO | S_IWUSR, show_temp_max, + store_temp_max, 3), + SENSOR_ATTR(temp5_max, S_IRUGO | S_IWUSR, show_temp_max, + store_temp_max, 4), + SENSOR_ATTR(temp6_max, S_IRUGO | S_IWUSR, show_temp_max, + store_temp_max, 5), + SENSOR_ATTR(temp7_max, S_IRUGO | S_IWUSR, show_temp_max, + store_temp_max, 6), + SENSOR_ATTR(temp8_max, S_IRUGO | S_IWUSR, show_temp_max, + store_temp_max, 7), + SENSOR_ATTR(temp9_max, S_IRUGO | S_IWUSR, show_temp_max, + store_temp_max, 8), }; static struct sensor_device_attribute sda_temp_max_hyst[] = { - SENSOR_ATTR(temp1_max_hyst, S_IRUGO | S_IWUSR, show_temp1_max_hyst, - store_temp1_max_hyst, 0), - SENSOR_ATTR(temp2_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, + SENSOR_ATTR(temp1_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, store_temp_max_hyst, 0), - SENSOR_ATTR(temp3_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, + SENSOR_ATTR(temp2_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, store_temp_max_hyst, 1), + SENSOR_ATTR(temp3_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, + store_temp_max_hyst, 2), + SENSOR_ATTR(temp4_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, + store_temp_max_hyst, 3), + SENSOR_ATTR(temp5_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, + store_temp_max_hyst, 4), + SENSOR_ATTR(temp6_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, + store_temp_max_hyst, 5), + SENSOR_ATTR(temp7_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, + store_temp_max_hyst, 6), + SENSOR_ATTR(temp8_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, + store_temp_max_hyst, 7), + SENSOR_ATTR(temp9_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst, + store_temp_max_hyst, 8), }; static struct sensor_device_attribute sda_temp_alarm[] = { @@ -958,11 +1274,12 @@ static struct sensor_device_attribute sda_temp_type[] = { }; #define show_pwm_reg(reg) \ -static ssize_t show_##reg (struct device *dev, struct device_attribute *attr, \ - char *buf) \ +static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \ + char *buf) \ { \ struct w83627ehf_data *data = w83627ehf_update_device(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ return sprintf(buf, "%d\n", data->reg[nr]); \ } @@ -978,9 +1295,14 @@ store_pwm_mode(struct device *dev, struct device_attribute *attr, struct w83627ehf_data *data = dev_get_drvdata(dev); struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); int nr = sensor_attr->index; - u32 val = simple_strtoul(buf, NULL, 10); + unsigned long val; + int err; u16 reg; + err = strict_strtoul(buf, 10, &val); + if (err < 0) + return err; + if (val > 1) return -EINVAL; mutex_lock(&data->update_lock); @@ -1001,11 +1323,18 @@ store_pwm(struct device *dev, struct device_attribute *attr, struct w83627ehf_data *data = dev_get_drvdata(dev); struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); int nr = sensor_attr->index; - u32 val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 0, 255); + unsigned long val; + int err; + + err = strict_strtoul(buf, 10, &val); + if (err < 0) + return err; + + val = SENSORS_LIMIT(val, 0, 255); mutex_lock(&data->update_lock); data->pwm[nr] = val; - w83627ehf_write_value(data, W83627EHF_REG_PWM[nr], val); + w83627ehf_write_value(data, data->REG_PWM[nr], val); mutex_unlock(&data->update_lock); return count; } @@ -1015,19 +1344,38 @@ store_pwm_enable(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) { struct w83627ehf_data *data = dev_get_drvdata(dev); + struct w83627ehf_sio_data *sio_data = dev->platform_data; struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); int nr = sensor_attr->index; - u32 val = simple_strtoul(buf, NULL, 10); + unsigned long val; + int err; u16 reg; - if (!val || (val > 4)) + err = strict_strtoul(buf, 10, &val); + if (err < 0) + return err; + + if (!val || (val > 4 && val != data->pwm_enable_orig[nr])) return -EINVAL; + /* SmartFan III mode is not supported on NCT6776F */ + if (sio_data->kind == nct6776 && val == 4) + return -EINVAL; + mutex_lock(&data->update_lock); - reg = w83627ehf_read_value(data, W83627EHF_REG_PWM_ENABLE[nr]); data->pwm_enable[nr] = val; - reg &= ~(0x03 << W83627EHF_PWM_ENABLE_SHIFT[nr]); - reg |= (val - 1) << W83627EHF_PWM_ENABLE_SHIFT[nr]; - w83627ehf_write_value(data, W83627EHF_REG_PWM_ENABLE[nr], reg); + if (sio_data->kind == nct6775 || sio_data->kind == nct6776) { + reg = w83627ehf_read_value(data, + NCT6775_REG_FAN_MODE[nr]); + reg &= 0x0f; + reg |= (val - 1) << 4; + w83627ehf_write_value(data, + NCT6775_REG_FAN_MODE[nr], reg); + } else { + reg = w83627ehf_read_value(data, W83627EHF_REG_PWM_ENABLE[nr]); + reg &= ~(0x03 << W83627EHF_PWM_ENABLE_SHIFT[nr]); + reg |= (val - 1) << W83627EHF_PWM_ENABLE_SHIFT[nr]; + w83627ehf_write_value(data, W83627EHF_REG_PWM_ENABLE[nr], reg); + } mutex_unlock(&data->update_lock); return count; } @@ -1038,9 +1386,10 @@ static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \ char *buf) \ { \ struct w83627ehf_data *data = w83627ehf_update_device(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ - return sprintf(buf, "%d\n", temp1_from_reg(data->reg[nr])); \ + return sprintf(buf, "%d\n", data->reg[nr] * 1000); \ } show_tol_temp(tolerance) @@ -1053,11 +1402,18 @@ store_target_temp(struct device *dev, struct device_attribute *attr, struct w83627ehf_data *data = dev_get_drvdata(dev); struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); int nr = sensor_attr->index; - u8 val = temp1_to_reg(simple_strtoul(buf, NULL, 10), 0, 127000); + long val; + int err; + + err = strict_strtol(buf, 10, &val); + if (err < 0) + return err; + + val = SENSORS_LIMIT(DIV_ROUND_CLOSEST(val, 1000), 0, 127); mutex_lock(&data->update_lock); data->target_temp[nr] = val; - w83627ehf_write_value(data, W83627EHF_REG_TARGET[nr], val); + w83627ehf_write_value(data, data->REG_TARGET[nr], val); mutex_unlock(&data->update_lock); return count; } @@ -1067,20 +1423,37 @@ store_tolerance(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) { struct w83627ehf_data *data = dev_get_drvdata(dev); + struct w83627ehf_sio_data *sio_data = dev->platform_data; struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); int nr = sensor_attr->index; u16 reg; + long val; + int err; + + err = strict_strtol(buf, 10, &val); + if (err < 0) + return err; + /* Limit the temp to 0C - 15C */ - u8 val = temp1_to_reg(simple_strtoul(buf, NULL, 10), 0, 15000); + val = SENSORS_LIMIT(DIV_ROUND_CLOSEST(val, 1000), 0, 15); mutex_lock(&data->update_lock); - reg = w83627ehf_read_value(data, W83627EHF_REG_TOLERANCE[nr]); - data->tolerance[nr] = val; - if (nr == 1) - reg = (reg & 0x0f) | (val << 4); - else + if (sio_data->kind == nct6775 || sio_data->kind == nct6776) { + /* Limit tolerance further for NCT6776F */ + if (sio_data->kind == nct6776 && val > 7) + val = 7; + reg = w83627ehf_read_value(data, NCT6775_REG_FAN_MODE[nr]); reg = (reg & 0xf0) | val; - w83627ehf_write_value(data, W83627EHF_REG_TOLERANCE[nr], reg); + w83627ehf_write_value(data, NCT6775_REG_FAN_MODE[nr], reg); + } else { + reg = w83627ehf_read_value(data, W83627EHF_REG_TOLERANCE[nr]); + if (nr == 1) + reg = (reg & 0x0f) | (val << 4); + else + reg = (reg & 0xf0) | val; + w83627ehf_write_value(data, W83627EHF_REG_TOLERANCE[nr], reg); + } + data->tolerance[nr] = val; mutex_unlock(&data->update_lock); return count; } @@ -1143,18 +1516,25 @@ static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \ char *buf) \ { \ struct w83627ehf_data *data = w83627ehf_update_device(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ return sprintf(buf, "%d\n", data->reg[nr]); \ -}\ +} \ static ssize_t \ store_##reg(struct device *dev, struct device_attribute *attr, \ const char *buf, size_t count) \ -{\ +{ \ struct w83627ehf_data *data = dev_get_drvdata(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ - u32 val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 1, 255); \ + unsigned long val; \ + int err; \ + err = strict_strtoul(buf, 10, &val); \ + if (err < 0) \ + return err; \ + val = SENSORS_LIMIT(val, 1, 255); \ mutex_lock(&data->update_lock); \ data->reg[nr] = val; \ w83627ehf_write_value(data, data->REG_##REG[nr], val); \ @@ -1172,10 +1552,12 @@ static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \ char *buf) \ { \ struct w83627ehf_data *data = w83627ehf_update_device(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ return sprintf(buf, "%d\n", \ - step_time_from_reg(data->reg[nr], data->pwm_mode[nr])); \ + step_time_from_reg(data->reg[nr], \ + data->pwm_mode[nr])); \ } \ \ static ssize_t \ @@ -1183,10 +1565,15 @@ store_##reg(struct device *dev, struct device_attribute *attr, \ const char *buf, size_t count) \ { \ struct w83627ehf_data *data = dev_get_drvdata(dev); \ - struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ int nr = sensor_attr->index; \ - u8 val = step_time_to_reg(simple_strtoul(buf, NULL, 10), \ - data->pwm_mode[nr]); \ + unsigned long val; \ + int err; \ + err = strict_strtoul(buf, 10, &val); \ + if (err < 0) \ + return err; \ + val = step_time_to_reg(val, data->pwm_mode[nr]); \ mutex_lock(&data->update_lock); \ data->reg[nr] = val; \ w83627ehf_write_value(data, W83627EHF_REG_##REG[nr], val); \ @@ -1283,7 +1670,8 @@ static void w83627ehf_device_remove_files(struct device *dev) for (i = 0; i < ARRAY_SIZE(sda_sf3_max_step_arrays); i++) { struct sensor_device_attribute *attr = &sda_sf3_max_step_arrays[i]; - if (data->REG_FAN_STEP_OUTPUT[attr->index] != 0xff) + if (data->REG_FAN_STEP_OUTPUT && + data->REG_FAN_STEP_OUTPUT[attr->index] != 0xff) device_remove_file(dev, &attr->dev_attr); } for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan4); i++) @@ -1309,12 +1697,15 @@ static void w83627ehf_device_remove_files(struct device *dev) device_remove_file(dev, &sda_target_temp[i].dev_attr); device_remove_file(dev, &sda_tolerance[i].dev_attr); } - for (i = 0; i < 3; i++) { - if ((i == 2) && data->temp3_disable) + for (i = 0; i < NUM_REG_TEMP; i++) { + if (!(data->have_temp & (1 << i))) continue; device_remove_file(dev, &sda_temp_input[i].dev_attr); + device_remove_file(dev, &sda_temp_label[i].dev_attr); device_remove_file(dev, &sda_temp_max[i].dev_attr); device_remove_file(dev, &sda_temp_max_hyst[i].dev_attr); + if (i > 2) + continue; device_remove_file(dev, &sda_temp_alarm[i].dev_attr); device_remove_file(dev, &sda_temp_type[i].dev_attr); } @@ -1335,15 +1726,17 @@ static inline void __devinit w83627ehf_init_device(struct w83627ehf_data *data) w83627ehf_write_value(data, W83627EHF_REG_CONFIG, tmp | 0x01); - /* Enable temp2 and temp3 if needed */ - for (i = 0; i < 2; i++) { - tmp = w83627ehf_read_value(data, - W83627EHF_REG_TEMP_CONFIG[i]); - if ((i == 1) && data->temp3_disable) + /* Enable temperature sensors if needed */ + for (i = 0; i < NUM_REG_TEMP; i++) { + if (!(data->have_temp & (1 << i))) + continue; + if (!data->reg_temp_config[i]) continue; + tmp = w83627ehf_read_value(data, + data->reg_temp_config[i]); if (tmp & 0x01) w83627ehf_write_value(data, - W83627EHF_REG_TEMP_CONFIG[i], + data->reg_temp_config[i], tmp & 0xfe); } @@ -1362,13 +1755,39 @@ static inline void __devinit w83627ehf_init_device(struct w83627ehf_data *data) } } +static void w82627ehf_swap_tempreg(struct w83627ehf_data *data, + int r1, int r2) +{ + u16 tmp; + + tmp = data->temp_src[r1]; + data->temp_src[r1] = data->temp_src[r2]; + data->temp_src[r2] = tmp; + + tmp = data->reg_temp[r1]; + data->reg_temp[r1] = data->reg_temp[r2]; + data->reg_temp[r2] = tmp; + + tmp = data->reg_temp_over[r1]; + data->reg_temp_over[r1] = data->reg_temp_over[r2]; + data->reg_temp_over[r2] = tmp; + + tmp = data->reg_temp_hyst[r1]; + data->reg_temp_hyst[r1] = data->reg_temp_hyst[r2]; + data->reg_temp_hyst[r2] = tmp; + + tmp = data->reg_temp_config[r1]; + data->reg_temp_config[r1] = data->reg_temp_config[r2]; + data->reg_temp_config[r2] = tmp; +} + static int __devinit w83627ehf_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; struct w83627ehf_sio_data *sio_data = dev->platform_data; struct w83627ehf_data *data; struct resource *res; - u8 fan4pin, fan5pin, en_vrm10; + u8 fan3pin, fan4pin, fan4min, fan5pin, en_vrm10; int i, err = 0; res = platform_get_resource(pdev, IORESOURCE_IO, 0); @@ -1380,7 +1799,8 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev) goto exit; } - if (!(data = kzalloc(sizeof(struct w83627ehf_data), GFP_KERNEL))) { + data = kzalloc(sizeof(struct w83627ehf_data), GFP_KERNEL); + if (!data) { err = -ENOMEM; goto exit_release; } @@ -1393,25 +1813,202 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev) /* 627EHG and 627EHF have 10 voltage inputs; 627DHG and 667HG have 9 */ data->in_num = (sio_data->kind == w83627ehf) ? 10 : 9; - /* 667HG has 3 pwms */ + /* 667HG, NCT6775F, and NCT6776F have 3 pwms */ data->pwm_num = (sio_data->kind == w83667hg - || sio_data->kind == w83667hg_b) ? 3 : 4; + || sio_data->kind == w83667hg_b + || sio_data->kind == nct6775 + || sio_data->kind == nct6776) ? 3 : 4; + data->have_temp = 0x07; /* Check temp3 configuration bit for 667HG */ - if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) { - data->temp3_disable = w83627ehf_read_value(data, - W83627EHF_REG_TEMP_CONFIG[1]) & 0x01; - data->in6_skip = !data->temp3_disable; + if (sio_data->kind == w83667hg) { + u8 reg; + + reg = w83627ehf_read_value(data, W83627EHF_REG_TEMP_CONFIG[2]); + if (reg & 0x01) + data->have_temp &= ~(1 << 2); + else + data->in6_skip = 1; /* either temp3 or in6 */ + } + + /* Deal with temperature register setup first. */ + if (sio_data->kind == nct6775 || sio_data->kind == nct6776) { + int mask = 0; + + /* + * Display temperature sensor output only if it monitors + * a source other than one already reported. Always display + * first three temperature registers, though. + */ + for (i = 0; i < NUM_REG_TEMP; i++) { + u8 src; + + data->reg_temp[i] = NCT6775_REG_TEMP[i]; + data->reg_temp_over[i] = NCT6775_REG_TEMP_OVER[i]; + data->reg_temp_hyst[i] = NCT6775_REG_TEMP_HYST[i]; + data->reg_temp_config[i] = NCT6775_REG_TEMP_CONFIG[i]; + + src = w83627ehf_read_value(data, + NCT6775_REG_TEMP_SOURCE[i]); + src &= 0x1f; + if (src && !(mask & (1 << src))) { + data->have_temp |= 1 << i; + mask |= 1 << src; + } + + data->temp_src[i] = src; + + /* + * Now do some register swapping if index 0..2 don't + * point to SYSTIN(1), CPUIN(2), and AUXIN(3). + * Idea is to have the first three attributes + * report SYSTIN, CPUIN, and AUXIN if possible + * without overriding the basic system configuration. + */ + if (i > 0 && data->temp_src[0] != 1 + && data->temp_src[i] == 1) + w82627ehf_swap_tempreg(data, 0, i); + if (i > 1 && data->temp_src[1] != 2 + && data->temp_src[i] == 2) + w82627ehf_swap_tempreg(data, 1, i); + if (i > 2 && data->temp_src[2] != 3 + && data->temp_src[i] == 3) + w82627ehf_swap_tempreg(data, 2, i); + } + if (sio_data->kind == nct6776) { + /* + * On NCT6776, AUXTIN and VIN3 pins are shared. + * Only way to detect it is to check if AUXTIN is used + * as a temperature source, and if that source is + * enabled. + * + * If that is the case, disable in6, which reports VIN3. + * Otherwise disable temp3. + */ + if (data->temp_src[2] == 3) { + u8 reg; + + if (data->reg_temp_config[2]) + reg = w83627ehf_read_value(data, + data->reg_temp_config[2]); + else + reg = 0; /* Assume AUXTIN is used */ + + if (reg & 0x01) + data->have_temp &= ~(1 << 2); + else + data->in6_skip = 1; + } + data->temp_label = nct6776_temp_label; + } else { + data->temp_label = nct6775_temp_label; + } + } else if (sio_data->kind == w83667hg_b) { + u8 reg; + + /* + * Temperature sources are selected with bank 0, registers 0x49 + * and 0x4a. + */ + for (i = 0; i < ARRAY_SIZE(W83627EHF_REG_TEMP); i++) { + data->reg_temp[i] = W83627EHF_REG_TEMP[i]; + data->reg_temp_over[i] = W83627EHF_REG_TEMP_OVER[i]; + data->reg_temp_hyst[i] = W83627EHF_REG_TEMP_HYST[i]; + data->reg_temp_config[i] = W83627EHF_REG_TEMP_CONFIG[i]; + } + reg = w83627ehf_read_value(data, 0x4a); + data->temp_src[0] = reg >> 5; + reg = w83627ehf_read_value(data, 0x49); + data->temp_src[1] = reg & 0x07; + data->temp_src[2] = (reg >> 4) & 0x07; + + /* + * W83667HG-B has another temperature register at 0x7e. + * The temperature source is selected with register 0x7d. + * Support it if the source differs from already reported + * sources. + */ + reg = w83627ehf_read_value(data, 0x7d); + reg &= 0x07; + if (reg != data->temp_src[0] && reg != data->temp_src[1] + && reg != data->temp_src[2]) { + data->temp_src[3] = reg; + data->have_temp |= 1 << 3; + } + + /* + * Chip supports either AUXTIN or VIN3. Try to find out which + * one. + */ + reg = w83627ehf_read_value(data, W83627EHF_REG_TEMP_CONFIG[2]); + if (data->temp_src[2] == 2 && (reg & 0x01)) + data->have_temp &= ~(1 << 2); + + if ((data->temp_src[2] == 2 && (data->have_temp & (1 << 2))) + || (data->temp_src[3] == 2 && (data->have_temp & (1 << 3)))) + data->in6_skip = 1; + + data->temp_label = w83667hg_b_temp_label; + } else { + /* Temperature sources are fixed */ + for (i = 0; i < 3; i++) { + data->reg_temp[i] = W83627EHF_REG_TEMP[i]; + data->reg_temp_over[i] = W83627EHF_REG_TEMP_OVER[i]; + data->reg_temp_hyst[i] = W83627EHF_REG_TEMP_HYST[i]; + data->reg_temp_config[i] = W83627EHF_REG_TEMP_CONFIG[i]; + } } - data->REG_FAN_START_OUTPUT = W83627EHF_REG_FAN_START_OUTPUT; - data->REG_FAN_STOP_OUTPUT = W83627EHF_REG_FAN_STOP_OUTPUT; - if (sio_data->kind == w83667hg_b) { + if (sio_data->kind == nct6775) { + data->has_fan_div = true; + data->fan_from_reg = fan_from_reg16; + data->fan_from_reg_min = fan_from_reg8; + data->REG_PWM = NCT6775_REG_PWM; + data->REG_TARGET = NCT6775_REG_TARGET; + data->REG_FAN = NCT6775_REG_FAN; + data->REG_FAN_MIN = W83627EHF_REG_FAN_MIN; + data->REG_FAN_START_OUTPUT = NCT6775_REG_FAN_START_OUTPUT; + data->REG_FAN_STOP_OUTPUT = NCT6775_REG_FAN_STOP_OUTPUT; + data->REG_FAN_STOP_TIME = NCT6775_REG_FAN_STOP_TIME; + data->REG_FAN_MAX_OUTPUT = NCT6775_REG_FAN_MAX_OUTPUT; + data->REG_FAN_STEP_OUTPUT = NCT6775_REG_FAN_STEP_OUTPUT; + } else if (sio_data->kind == nct6776) { + data->has_fan_div = false; + data->fan_from_reg = fan_from_reg13; + data->fan_from_reg_min = fan_from_reg13; + data->REG_PWM = NCT6775_REG_PWM; + data->REG_TARGET = NCT6775_REG_TARGET; + data->REG_FAN = NCT6775_REG_FAN; + data->REG_FAN_MIN = NCT6776_REG_FAN_MIN; + data->REG_FAN_START_OUTPUT = NCT6775_REG_FAN_START_OUTPUT; + data->REG_FAN_STOP_OUTPUT = NCT6775_REG_FAN_STOP_OUTPUT; + data->REG_FAN_STOP_TIME = NCT6775_REG_FAN_STOP_TIME; + } else if (sio_data->kind == w83667hg_b) { + data->has_fan_div = true; + data->fan_from_reg = fan_from_reg8; + data->fan_from_reg_min = fan_from_reg8; + data->REG_PWM = W83627EHF_REG_PWM; + data->REG_TARGET = W83627EHF_REG_TARGET; + data->REG_FAN = W83627EHF_REG_FAN; + data->REG_FAN_MIN = W83627EHF_REG_FAN_MIN; + data->REG_FAN_START_OUTPUT = W83627EHF_REG_FAN_START_OUTPUT; + data->REG_FAN_STOP_OUTPUT = W83627EHF_REG_FAN_STOP_OUTPUT; + data->REG_FAN_STOP_TIME = W83627EHF_REG_FAN_STOP_TIME; data->REG_FAN_MAX_OUTPUT = W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B; data->REG_FAN_STEP_OUTPUT = W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B; } else { + data->has_fan_div = true; + data->fan_from_reg = fan_from_reg8; + data->fan_from_reg_min = fan_from_reg8; + data->REG_PWM = W83627EHF_REG_PWM; + data->REG_TARGET = W83627EHF_REG_TARGET; + data->REG_FAN = W83627EHF_REG_FAN; + data->REG_FAN_MIN = W83627EHF_REG_FAN_MIN; + data->REG_FAN_START_OUTPUT = W83627EHF_REG_FAN_START_OUTPUT; + data->REG_FAN_STOP_OUTPUT = W83627EHF_REG_FAN_STOP_OUTPUT; + data->REG_FAN_STOP_TIME = W83627EHF_REG_FAN_STOP_TIME; data->REG_FAN_MAX_OUTPUT = W83627EHF_REG_FAN_MAX_OUTPUT_COMMON; data->REG_FAN_STEP_OUTPUT = @@ -1424,7 +2021,8 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev) data->vrm = vid_which_vrm(); superio_enter(sio_data->sioreg); /* Read VID value */ - if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) { + if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b || + sio_data->kind == nct6775 || sio_data->kind == nct6776) { /* W83667HG has different pins for VID input and output, so we can get the VID input values directly at logical device D 0xe3. */ @@ -1475,13 +2073,44 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev) } /* fan4 and fan5 share some pins with the GPIO and serial flash */ - if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) { - fan5pin = superio_inb(sio_data->sioreg, 0x27) & 0x20; + if (sio_data->kind == nct6775) { + /* On NCT6775, fan4 shares pins with the fdc interface */ + fan3pin = 1; + fan4pin = !(superio_inb(sio_data->sioreg, 0x2A) & 0x80); + fan4min = 0; + fan5pin = 0; + } else if (sio_data->kind == nct6776) { + fan3pin = !(superio_inb(sio_data->sioreg, 0x24) & 0x40); + fan4pin = !!(superio_inb(sio_data->sioreg, 0x1C) & 0x01); + fan5pin = !!(superio_inb(sio_data->sioreg, 0x1C) & 0x02); + fan4min = fan4pin; + } else if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) { + fan3pin = 1; fan4pin = superio_inb(sio_data->sioreg, 0x27) & 0x40; + fan5pin = superio_inb(sio_data->sioreg, 0x27) & 0x20; + fan4min = fan4pin; } else { - fan5pin = !(superio_inb(sio_data->sioreg, 0x24) & 0x02); + fan3pin = 1; fan4pin = !(superio_inb(sio_data->sioreg, 0x29) & 0x06); + fan5pin = !(superio_inb(sio_data->sioreg, 0x24) & 0x02); + fan4min = fan4pin; } + + if (fan_debounce && + (sio_data->kind == nct6775 || sio_data->kind == nct6776)) { + u8 tmp; + + superio_select(sio_data->sioreg, W83627EHF_LD_HWM); + tmp = superio_inb(sio_data->sioreg, NCT6775_REG_FAN_DEBOUNCE); + if (sio_data->kind == nct6776) + superio_outb(sio_data->sioreg, NCT6775_REG_FAN_DEBOUNCE, + 0x3e | tmp); + else + superio_outb(sio_data->sioreg, NCT6775_REG_FAN_DEBOUNCE, + 0x1e | tmp); + pr_info("Enabled fan debounce for chip %s\n", data->name); + } + superio_exit(sio_data->sioreg); /* It looks like fan4 and fan5 pins can be alternatively used @@ -1490,26 +2119,54 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev) connected fan5 as input unless they are emitting log 1, which is not the default. */ - data->has_fan = 0x07; /* fan1, fan2 and fan3 */ - i = w83627ehf_read_value(data, W83627EHF_REG_FANDIV1); - if ((i & (1 << 2)) && fan4pin) - data->has_fan |= (1 << 3); - if (!(i & (1 << 1)) && fan5pin) - data->has_fan |= (1 << 4); + data->has_fan = data->has_fan_min = 0x03; /* fan1 and fan2 */ + + data->has_fan |= (fan3pin << 2); + data->has_fan_min |= (fan3pin << 2); + + /* + * NCT6775F and NCT6776F don't have the W83627EHF_REG_FANDIV1 register + */ + if (sio_data->kind == nct6775 || sio_data->kind == nct6776) { + data->has_fan |= (fan4pin << 3) | (fan5pin << 4); + data->has_fan_min |= (fan4min << 3) | (fan5pin << 4); + } else { + i = w83627ehf_read_value(data, W83627EHF_REG_FANDIV1); + if ((i & (1 << 2)) && fan4pin) { + data->has_fan |= (1 << 3); + data->has_fan_min |= (1 << 3); + } + if (!(i & (1 << 1)) && fan5pin) { + data->has_fan |= (1 << 4); + data->has_fan_min |= (1 << 4); + } + } /* Read fan clock dividers immediately */ - w83627ehf_update_fan_div(data); + w83627ehf_update_fan_div_common(dev, data); + + /* Read pwm data to save original values */ + w83627ehf_update_pwm_common(dev, data); + for (i = 0; i < data->pwm_num; i++) + data->pwm_enable_orig[i] = data->pwm_enable[i]; + + /* Read pwm data to save original values */ + w83627ehf_update_pwm_common(dev, data); + for (i = 0; i < data->pwm_num; i++) + data->pwm_enable_orig[i] = data->pwm_enable[i]; /* Register sysfs hooks */ - for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays); i++) - if ((err = device_create_file(dev, - &sda_sf3_arrays[i].dev_attr))) + for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays); i++) { + err = device_create_file(dev, &sda_sf3_arrays[i].dev_attr); + if (err) goto exit_remove; + } for (i = 0; i < ARRAY_SIZE(sda_sf3_max_step_arrays); i++) { struct sensor_device_attribute *attr = &sda_sf3_max_step_arrays[i]; - if (data->REG_FAN_STEP_OUTPUT[attr->index] != 0xff) { + if (data->REG_FAN_STEP_OUTPUT && + data->REG_FAN_STEP_OUTPUT[attr->index] != 0xff) { err = device_create_file(dev, &attr->dev_attr); if (err) goto exit_remove; @@ -1518,8 +2175,9 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev) /* if fan4 is enabled create the sf3 files for it */ if ((data->has_fan & (1 << 3)) && data->pwm_num >= 4) for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan4); i++) { - if ((err = device_create_file(dev, - &sda_sf3_arrays_fan4[i].dev_attr))) + err = device_create_file(dev, + &sda_sf3_arrays_fan4[i].dev_attr); + if (err) goto exit_remove; } @@ -1541,12 +2199,20 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev) if ((err = device_create_file(dev, &sda_fan_input[i].dev_attr)) || (err = device_create_file(dev, - &sda_fan_alarm[i].dev_attr)) - || (err = device_create_file(dev, - &sda_fan_div[i].dev_attr)) - || (err = device_create_file(dev, - &sda_fan_min[i].dev_attr))) + &sda_fan_alarm[i].dev_attr))) goto exit_remove; + if (sio_data->kind != nct6776) { + err = device_create_file(dev, + &sda_fan_div[i].dev_attr); + if (err) + goto exit_remove; + } + if (data->has_fan_min & (1 << i)) { + err = device_create_file(dev, + &sda_fan_min[i].dev_attr); + if (err) + goto exit_remove; + } if (i < data->pwm_num && ((err = device_create_file(dev, &sda_pwm[i].dev_attr)) @@ -1562,16 +2228,33 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev) } } - for (i = 0; i < 3; i++) { - if ((i == 2) && data->temp3_disable) + for (i = 0; i < NUM_REG_TEMP; i++) { + if (!(data->have_temp & (1 << i))) + continue; + err = device_create_file(dev, &sda_temp_input[i].dev_attr); + if (err) + goto exit_remove; + if (data->temp_label) { + err = device_create_file(dev, + &sda_temp_label[i].dev_attr); + if (err) + goto exit_remove; + } + if (data->reg_temp_over[i]) { + err = device_create_file(dev, + &sda_temp_max[i].dev_attr); + if (err) + goto exit_remove; + } + if (data->reg_temp_hyst[i]) { + err = device_create_file(dev, + &sda_temp_max_hyst[i].dev_attr); + if (err) + goto exit_remove; + } + if (i > 2) continue; if ((err = device_create_file(dev, - &sda_temp_input[i].dev_attr)) - || (err = device_create_file(dev, - &sda_temp_max[i].dev_attr)) - || (err = device_create_file(dev, - &sda_temp_max_hyst[i].dev_attr)) - || (err = device_create_file(dev, &sda_temp_alarm[i].dev_attr)) || (err = device_create_file(dev, &sda_temp_type[i].dev_attr))) @@ -1632,6 +2315,8 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr, static const char __initdata sio_name_W83627DHG_P[] = "W83627DHG-P"; static const char __initdata sio_name_W83667HG[] = "W83667HG"; static const char __initdata sio_name_W83667HG_B[] = "W83667HG-B"; + static const char __initdata sio_name_NCT6775[] = "NCT6775F"; + static const char __initdata sio_name_NCT6776[] = "NCT6776F"; u16 val; const char *sio_name; @@ -1668,6 +2353,14 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr, sio_data->kind = w83667hg_b; sio_name = sio_name_W83667HG_B; break; + case SIO_NCT6775_ID: + sio_data->kind = nct6775; + sio_name = sio_name_NCT6775; + break; + case SIO_NCT6776_ID: + sio_data->kind = nct6776; + sio_name = sio_name_NCT6776; + break; default: if (val != 0xffff) pr_debug("unsupported chip ID: 0x%04x\n", val); @@ -1689,7 +2382,8 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr, /* Activate logical device if needed */ val = superio_inb(sioaddr, SIO_REG_ENABLE); if (!(val & 0x01)) { - pr_warn("Forcibly enabling Super-I/O. Sensor is probably unusable.\n"); + pr_warn("Forcibly enabling Super-I/O. " + "Sensor is probably unusable.\n"); superio_outb(sioaddr, SIO_REG_ENABLE, val | 0x01); } @@ -1726,7 +2420,8 @@ static int __init sensors_w83627ehf_init(void) if (err) goto exit; - if (!(pdev = platform_device_alloc(DRVNAME, address))) { + pdev = platform_device_alloc(DRVNAME, address); + if (!pdev) { err = -ENOMEM; pr_err("Device allocation failed\n"); goto exit_unregister; |