17 files changed, 39364 insertions, 0 deletions

diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig
index 9cfbdb318ed..3fd7199301b 100644
--- a/drivers/tty/Kconfig
+++ b/drivers/tty/Kconfig
@@ -147,4 +147,175 @@ config LEGACY_PTY_COUNT
 	  When not in use, each legacy PTY occupies 12 bytes on 32-bit
 	  architectures and 24 bytes on 64-bit architectures.
 
+config BFIN_JTAG_COMM
+	tristate "Blackfin JTAG Communication"
+	depends on BLACKFIN
+	help
+	  Add support for emulating a TTY device over the Blackfin JTAG.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bfin_jtag_comm.
+
+config BFIN_JTAG_COMM_CONSOLE
+	bool "Console on Blackfin JTAG"
+	depends on BFIN_JTAG_COMM=y
+
+config SERIAL_NONSTANDARD
+	bool "Non-standard serial port support"
+	depends on HAS_IOMEM
+	---help---
+	  Say Y here if you have any non-standard serial boards -- boards
+	  which aren't supported using the standard "dumb" serial driver.
+	  This includes intelligent serial boards such as Cyclades,
+	  Digiboards, etc. These are usually used for systems that need many
+	  serial ports because they serve many terminals or dial-in
+	  connections.
+
+	  Note that the answer to this question won't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about non-standard serial boards.
+
+	  Most people can say N here.
+
+config ROCKETPORT
+	tristate "Comtrol RocketPort support"
+	depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
+	help
+	  This driver supports Comtrol RocketPort and RocketModem PCI boards.   
+          These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or
+          modems.  For information about the RocketPort/RocketModem  boards
+          and this driver read <file:Documentation/serial/rocket.txt>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called rocket.
+
+	  If you want to compile this driver into the kernel, say Y here.  If
+          you don't have a Comtrol RocketPort/RocketModem card installed, say N.
+
+config CYCLADES
+	tristate "Cyclades async mux support"
+	depends on SERIAL_NONSTANDARD && (PCI || ISA)
+	select FW_LOADER
+	---help---
+	  This driver supports Cyclades Z and Y multiserial boards.
+	  You would need something like this to connect more than two modems to
+	  your Linux box, for instance in order to become a dial-in server.
+
+	  For information about the Cyclades-Z card, read
+	  <file:Documentation/serial/README.cycladesZ>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called cyclades.
+
+	  If you haven't heard about it, it's safe to say N.
+
+config CYZ_INTR
+	bool "Cyclades-Z interrupt mode operation (EXPERIMENTAL)"
+	depends on EXPERIMENTAL && CYCLADES
+	help
+	  The Cyclades-Z family of multiport cards allows 2 (two) driver op
+	  modes: polling and interrupt. In polling mode, the driver will check
+	  the status of the Cyclades-Z ports every certain amount of time
+	  (which is called polling cycle and is configurable). In interrupt
+	  mode, it will use an interrupt line (IRQ) in order to check the
+	  status of the Cyclades-Z ports. The default op mode is polling. If
+	  unsure, say N.
+
+config MOXA_INTELLIO
+	tristate "Moxa Intellio support"
+	depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
+	select FW_LOADER
+	help
+	  Say Y here if you have a Moxa Intellio multiport serial card.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called moxa.
+
+config MOXA_SMARTIO
+	tristate "Moxa SmartIO support v. 2.0"
+	depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA)
+	help
+	  Say Y here if you have a Moxa SmartIO multiport serial card and/or
+	  want to help develop a new version of this driver.
+
+	  This is upgraded (1.9.1) driver from original Moxa drivers with
+	  changes finally resulting in PCI probing.
+
+	  This driver can also be built as a module. The module will be called
+	  mxser. If you want to do that, say M here.
+
+config SYNCLINK
+	tristate "Microgate SyncLink card support"
+	depends on SERIAL_NONSTANDARD && PCI && ISA_DMA_API
+	help
+	  Provides support for the SyncLink ISA and PCI multiprotocol serial
+	  adapters. These adapters support asynchronous and HDLC bit
+	  synchronous communication up to 10Mbps (PCI adapter).
+
+	  This driver can only be built as a module ( = code which can be
+	  inserted in and removed from the running kernel whenever you want).
+	  The module will be called synclink.  If you want to do that, say M
+	  here.
+
+config SYNCLINKMP
+	tristate "SyncLink Multiport support"
+	depends on SERIAL_NONSTANDARD && PCI
+	help
+	  Enable support for the SyncLink Multiport (2 or 4 ports)
+	  serial adapter, running asynchronous and HDLC communications up
+	  to 2.048Mbps. Each ports is independently selectable for
+	  RS-232, V.35, RS-449, RS-530, and X.21
+
+	  This driver may be built as a module ( = code which can be
+	  inserted in and removed from the running kernel whenever you want).
+	  The module will be called synclinkmp.  If you want to do that, say M
+	  here.
+
+config SYNCLINK_GT
+	tristate "SyncLink GT/AC support"
+	depends on SERIAL_NONSTANDARD && PCI
+	help
+	  Support for SyncLink GT and SyncLink AC families of
+	  synchronous and asynchronous serial adapters
+	  manufactured by Microgate Systems, Ltd. (www.microgate.com)
+
+config NOZOMI
+	tristate "HSDPA Broadband Wireless Data Card - Globe Trotter"
+	depends on PCI && EXPERIMENTAL
+	help
+	  If you have a HSDPA driver Broadband Wireless Data Card -
+	  Globe Trotter PCMCIA card, say Y here.
+
+	  To compile this driver as a module, choose M here, the module
+	  will be called nozomi.
+
+config ISI
+	tristate "Multi-Tech multiport card support (EXPERIMENTAL)"
+	depends on SERIAL_NONSTANDARD && PCI
+	select FW_LOADER
+	help
+	  This is a driver for the Multi-Tech cards which provide several
+	  serial ports.  The driver is experimental and can currently only be
+	  built as a module. The module will be called isicom.
+	  If you want to do that, choose M here.
+
+config N_HDLC
+	tristate "HDLC line discipline support"
+	depends on SERIAL_NONSTANDARD
+	help
+	  Allows synchronous HDLC communications with tty device drivers that
+	  support synchronous HDLC such as the Microgate SyncLink adapter.
+
+	  This driver can be built as a module ( = code which can be
+	  inserted in and removed from the running kernel whenever you want).
+	  The module will be called n_hdlc. If you want to do that, say M
+	  here.
+
+config N_GSM
+	tristate "GSM MUX line discipline support (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	depends on NET
+	help
+	  This line discipline provides support for the GSM MUX protocol and
+	  presents the mux as a set of 61 individual tty devices.
 
diff --git a/drivers/tty/Makefile b/drivers/tty/Makefile
index 396277216e4..e549da348a0 100644
--- a/drivers/tty/Makefile
+++ b/drivers/tty/Makefile
@@ -11,3 +11,16 @@ obj-$(CONFIG_R3964)		+= n_r3964.o
 obj-y				+= vt/
 obj-$(CONFIG_HVC_DRIVER)	+= hvc/
 obj-y				+= serial/
+
+# tty drivers
+obj-$(CONFIG_AMIGA_BUILTIN_SERIAL) += amiserial.o
+obj-$(CONFIG_BFIN_JTAG_COMM)	+= bfin_jtag_comm.o
+obj-$(CONFIG_CYCLADES)		+= cyclades.o
+obj-$(CONFIG_ISI)		+= isicom.o
+obj-$(CONFIG_MOXA_INTELLIO)	+= moxa.o
+obj-$(CONFIG_MOXA_SMARTIO)	+= mxser.o
+obj-$(CONFIG_NOZOMI)		+= nozomi.o
+obj-$(CONFIG_ROCKETPORT)	+= rocket.o
+obj-$(CONFIG_SYNCLINK_GT)	+= synclink_gt.o
+obj-$(CONFIG_SYNCLINKMP)	+= synclinkmp.o
+obj-$(CONFIG_SYNCLINK)		+= synclink.o
diff --git a/drivers/tty/amiserial.c b/drivers/tty/amiserial.c
new file mode 100644
index 00000000000..f214e502247
--- /dev/null
+++ b/drivers/tty/amiserial.c
@@ -0,0 +1,2178 @@
+/*
+ *  linux/drivers/char/amiserial.c
+ *
+ * Serial driver for the amiga builtin port.
+ *
+ * This code was created by taking serial.c version 4.30 from kernel
+ * release 2.3.22, replacing all hardware related stuff with the
+ * corresponding amiga hardware actions, and removing all irrelevant
+ * code. As a consequence, it uses many of the constants and names
+ * associated with the registers and bits of 16550 compatible UARTS -
+ * but only to keep track of status, etc in the state variables. It
+ * was done this was to make it easier to keep the code in line with
+ * (non hardware specific) changes to serial.c.
+ *
+ * The port is registered with the tty driver as minor device 64, and
+ * therefore other ports should should only use 65 upwards.
+ *
+ * Richard Lucock 28/12/99
+ *
+ *  Copyright (C) 1991, 1992  Linus Torvalds
+ *  Copyright (C) 1992, 1993, 1994, 1995, 1996, 1997, 
+ * 		1998, 1999  Theodore Ts'o
+ *
+ */
+
+/*
+ * Serial driver configuration section.  Here are the various options:
+ *
+ * SERIAL_PARANOIA_CHECK
+ * 		Check the magic number for the async_structure where
+ * 		ever possible.
+ */
+
+#include <linux/delay.h>
+
+#undef SERIAL_PARANOIA_CHECK
+#define SERIAL_DO_RESTART
+
+/* Set of debugging defines */
+
+#undef SERIAL_DEBUG_INTR
+#undef SERIAL_DEBUG_OPEN
+#undef SERIAL_DEBUG_FLOW
+#undef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
+
+/* Sanity checks */
+
+#if defined(MODULE) && defined(SERIAL_DEBUG_MCOUNT)
+#define DBG_CNT(s) printk("(%s): [%x] refc=%d, serc=%d, ttyc=%d -> %s\n", \
+ tty->name, (info->flags), serial_driver->refcount,info->count,tty->count,s)
+#else
+#define DBG_CNT(s)
+#endif
+
+/*
+ * End of serial driver configuration section.
+ */
+
+#include <linux/module.h>
+
+#include <linux/types.h>
+#include <linux/serial.h>
+#include <linux/serialP.h>
+#include <linux/serial_reg.h>
+static char *serial_version = "4.30";
+
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/timer.h>
+#include <linux/interrupt.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/console.h>
+#include <linux/major.h>
+#include <linux/string.h>
+#include <linux/fcntl.h>
+#include <linux/ptrace.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/seq_file.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/bitops.h>
+#include <linux/platform_device.h>
+
+#include <asm/setup.h>
+
+#include <asm/system.h>
+
+#include <asm/irq.h>
+
+#include <asm/amigahw.h>
+#include <asm/amigaints.h>
+
+#define custom amiga_custom
+static char *serial_name = "Amiga-builtin serial driver";
+
+static struct tty_driver *serial_driver;
+
+/* number of characters left in xmit buffer before we ask for more */
+#define WAKEUP_CHARS 256
+
+static struct async_struct *IRQ_ports;
+
+static unsigned char current_ctl_bits;
+
+static void change_speed(struct async_struct *info, struct ktermios *old);
+static void rs_wait_until_sent(struct tty_struct *tty, int timeout);
+
+
+static struct serial_state rs_table[1];
+
+#define NR_PORTS ARRAY_SIZE(rs_table)
+
+#include <asm/uaccess.h>
+
+#define serial_isroot()	(capable(CAP_SYS_ADMIN))
+
+
+static inline int serial_paranoia_check(struct async_struct *info,
+					char *name, const char *routine)
+{
+#ifdef SERIAL_PARANOIA_CHECK
+	static const char *badmagic =
+		"Warning: bad magic number for serial struct (%s) in %s\n";
+	static const char *badinfo =
+		"Warning: null async_struct for (%s) in %s\n";
+
+	if (!info) {
+		printk(badinfo, name, routine);
+		return 1;
+	}
+	if (info->magic != SERIAL_MAGIC) {
+		printk(badmagic, name, routine);
+		return 1;
+	}
+#endif
+	return 0;
+}
+
+/* some serial hardware definitions */
+#define SDR_OVRUN   (1<<15)
+#define SDR_RBF     (1<<14)
+#define SDR_TBE     (1<<13)
+#define SDR_TSRE    (1<<12)
+
+#define SERPER_PARENB    (1<<15)
+
+#define AC_SETCLR   (1<<15)
+#define AC_UARTBRK  (1<<11)
+
+#define SER_DTR     (1<<7)
+#define SER_RTS     (1<<6)
+#define SER_DCD     (1<<5)
+#define SER_CTS     (1<<4)
+#define SER_DSR     (1<<3)
+
+static __inline__ void rtsdtr_ctrl(int bits)
+{
+    ciab.pra = ((bits & (SER_RTS | SER_DTR)) ^ (SER_RTS | SER_DTR)) | (ciab.pra & ~(SER_RTS | SER_DTR));
+}
+
+/*
+ * ------------------------------------------------------------
+ * rs_stop() and rs_start()
+ *
+ * This routines are called before setting or resetting tty->stopped.
+ * They enable or disable transmitter interrupts, as necessary.
+ * ------------------------------------------------------------
+ */
+static void rs_stop(struct tty_struct *tty)
+{
+	struct async_struct *info = tty->driver_data;
+	unsigned long flags;
+
+	if (serial_paranoia_check(info, tty->name, "rs_stop"))
+		return;
+
+	local_irq_save(flags);
+	if (info->IER & UART_IER_THRI) {
+		info->IER &= ~UART_IER_THRI;
+		/* disable Tx interrupt and remove any pending interrupts */
+		custom.intena = IF_TBE;
+		mb();
+		custom.intreq = IF_TBE;
+		mb();
+	}
+	local_irq_restore(flags);
+}
+
+static void rs_start(struct tty_struct *tty)
+{
+	struct async_struct *info = tty->driver_data;
+	unsigned long flags;
+
+	if (serial_paranoia_check(info, tty->name, "rs_start"))
+		return;
+
+	local_irq_save(flags);
+	if (info->xmit.head != info->xmit.tail
+	    && info->xmit.buf
+	    && !(info->IER & UART_IER_THRI)) {
+		info->IER |= UART_IER_THRI;
+		custom.intena = IF_SETCLR | IF_TBE;
+		mb();
+		/* set a pending Tx Interrupt, transmitter should restart now */
+		custom.intreq = IF_SETCLR | IF_TBE;
+		mb();
+	}
+	local_irq_restore(flags);
+}
+
+/*
+ * ----------------------------------------------------------------------
+ *
+ * Here starts the interrupt handling routines.  All of the following
+ * subroutines are declared as inline and are folded into
+ * rs_interrupt().  They were separated out for readability's sake.
+ *
+ * Note: rs_interrupt() is a "fast" interrupt, which means that it
+ * runs with interrupts turned off.  People who may want to modify
+ * rs_interrupt() should try to keep the interrupt handler as fast as
+ * possible.  After you are done making modifications, it is not a bad
+ * idea to do:
+ * 
+ * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c
+ *
+ * and look at the resulting assemble code in serial.s.
+ *
+ * 				- Ted Ts'o (tytso@mit.edu), 7-Mar-93
+ * -----------------------------------------------------------------------
+ */
+
+/*
+ * This routine is used by the interrupt handler to schedule
+ * processing in the software interrupt portion of the driver.
+ */
+static void rs_sched_event(struct async_struct *info,
+			   int event)
+{
+	info->event |= 1 << event;
+	tasklet_schedule(&info->tlet);
+}
+
+static void receive_chars(struct async_struct *info)
+{
+        int status;
+	int serdatr;
+	struct tty_struct *tty = info->tty;
+	unsigned char ch, flag;
+	struct	async_icount *icount;
+	int oe = 0;
+
+	icount = &info->state->icount;
+
+	status = UART_LSR_DR; /* We obviously have a character! */
+	serdatr = custom.serdatr;
+	mb();
+	custom.intreq = IF_RBF;
+	mb();
+
+	if((serdatr & 0x1ff) == 0)
+	    status |= UART_LSR_BI;
+	if(serdatr & SDR_OVRUN)
+	    status |= UART_LSR_OE;
+
+	ch = serdatr & 0xff;
+	icount->rx++;
+
+#ifdef SERIAL_DEBUG_INTR
+	printk("DR%02x:%02x...", ch, status);
+#endif
+	flag = TTY_NORMAL;
+
+	/*
+	 * We don't handle parity or frame errors - but I have left
+	 * the code in, since I'm not sure that the errors can't be
+	 * detected.
+	 */
+
+	if (status & (UART_LSR_BI | UART_LSR_PE |
+		      UART_LSR_FE | UART_LSR_OE)) {
+	  /*
+	   * For statistics only
+	   */
+	  if (status & UART_LSR_BI) {
+	    status &= ~(UART_LSR_FE | UART_LSR_PE);
+	    icount->brk++;
+	  } else if (status & UART_LSR_PE)
+	    icount->parity++;
+	  else if (status & UART_LSR_FE)
+	    icount->frame++;
+	  if (status & UART_LSR_OE)
+	    icount->overrun++;
+
+	  /*
+	   * Now check to see if character should be
+	   * ignored, and mask off conditions which
+	   * should be ignored.
+	   */
+	  if (status & info->ignore_status_mask)
+	    goto out;
+
+	  status &= info->read_status_mask;
+
+	  if (status & (UART_LSR_BI)) {
+#ifdef SERIAL_DEBUG_INTR
+	    printk("handling break....");
+#endif
+	    flag = TTY_BREAK;
+	    if (info->flags & ASYNC_SAK)
+	      do_SAK(tty);
+	  } else if (status & UART_LSR_PE)
+	    flag = TTY_PARITY;
+	  else if (status & UART_LSR_FE)
+	    flag = TTY_FRAME;
+	  if (status & UART_LSR_OE) {
+	    /*
+	     * Overrun is special, since it's
+	     * reported immediately, and doesn't
+	     * affect the current character
+	     */
+	     oe = 1;
+	  }
+	}
+	tty_insert_flip_char(tty, ch, flag);
+	if (oe == 1)
+		tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+	tty_flip_buffer_push(tty);
+out:
+	return;
+}
+
+static void transmit_chars(struct async_struct *info)
+{
+	custom.intreq = IF_TBE;
+	mb();
+	if (info->x_char) {
+	        custom.serdat = info->x_char | 0x100;
+		mb();
+		info->state->icount.tx++;
+		info->x_char = 0;
+		return;
+	}
+	if (info->xmit.head == info->xmit.tail
+	    || info->tty->stopped
+	    || info->tty->hw_stopped) {
+		info->IER &= ~UART_IER_THRI;
+	        custom.intena = IF_TBE;
+		mb();
+		return;
+	}
+
+	custom.serdat = info->xmit.buf[info->xmit.tail++] | 0x100;
+	mb();
+	info->xmit.tail = info->xmit.tail & (SERIAL_XMIT_SIZE-1);
+	info->state->icount.tx++;
+
+	if (CIRC_CNT(info->xmit.head,
+		     info->xmit.tail,
+		     SERIAL_XMIT_SIZE) < WAKEUP_CHARS)
+		rs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
+
+#ifdef SERIAL_DEBUG_INTR
+	printk("THRE...");
+#endif
+	if (info->xmit.head == info->xmit.tail) {
+	        custom.intena = IF_TBE;
+		mb();
+		info->IER &= ~UART_IER_THRI;
+	}
+}
+
+static void check_modem_status(struct async_struct *info)
+{
+	unsigned char status = ciab.pra & (SER_DCD | SER_CTS | SER_DSR);
+	unsigned char dstatus;
+	struct	async_icount *icount;
+
+	/* Determine bits that have changed */
+	dstatus = status ^ current_ctl_bits;
+	current_ctl_bits = status;
+
+	if (dstatus) {
+		icount = &info->state->icount;
+		/* update input line counters */
+		if (dstatus & SER_DSR)
+			icount->dsr++;
+		if (dstatus & SER_DCD) {
+			icount->dcd++;
+#ifdef CONFIG_HARD_PPS
+			if ((info->flags & ASYNC_HARDPPS_CD) &&
+			    !(status & SER_DCD))
+				hardpps();
+#endif
+		}
+		if (dstatus & SER_CTS)
+			icount->cts++;
+		wake_up_interruptible(&info->delta_msr_wait);
+	}
+
+	if ((info->flags & ASYNC_CHECK_CD) && (dstatus & SER_DCD)) {
+#if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR))
+		printk("ttyS%d CD now %s...", info->line,
+		       (!(status & SER_DCD)) ? "on" : "off");
+#endif
+		if (!(status & SER_DCD))
+			wake_up_interruptible(&info->open_wait);
+		else {
+#ifdef SERIAL_DEBUG_OPEN
+			printk("doing serial hangup...");
+#endif
+			if (info->tty)
+				tty_hangup(info->tty);
+		}
+	}
+	if (info->flags & ASYNC_CTS_FLOW) {
+		if (info->tty->hw_stopped) {
+			if (!(status & SER_CTS)) {
+#if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW))
+				printk("CTS tx start...");
+#endif
+				info->tty->hw_stopped = 0;
+				info->IER |= UART_IER_THRI;
+				custom.intena = IF_SETCLR | IF_TBE;
+				mb();
+				/* set a pending Tx Interrupt, transmitter should restart now */
+				custom.intreq = IF_SETCLR | IF_TBE;
+				mb();
+				rs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
+				return;
+			}
+		} else {
+			if ((status & SER_CTS)) {
+#if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW))
+				printk("CTS tx stop...");
+#endif
+				info->tty->hw_stopped = 1;
+				info->IER &= ~UART_IER_THRI;
+				/* disable Tx interrupt and remove any pending interrupts */
+				custom.intena = IF_TBE;
+				mb();
+				custom.intreq = IF_TBE;
+				mb();
+			}
+		}
+	}
+}
+
+static irqreturn_t ser_vbl_int( int irq, void *data)
+{
+        /* vbl is just a periodic interrupt we tie into to update modem status */
+	struct async_struct * info = IRQ_ports;
+	/*
+	 * TBD - is it better to unregister from this interrupt or to
+	 * ignore it if MSI is clear ?
+	 */
+	if(info->IER & UART_IER_MSI)
+	  check_modem_status(info);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t ser_rx_int(int irq, void *dev_id)
+{
+	struct async_struct * info;
+
+#ifdef SERIAL_DEBUG_INTR
+	printk("ser_rx_int...");
+#endif
+
+	info = IRQ_ports;
+	if (!info || !info->tty)
+		return IRQ_NONE;
+
+	receive_chars(info);
+	info->last_active = jiffies;
+#ifdef SERIAL_DEBUG_INTR
+	printk("end.\n");
+#endif
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t ser_tx_int(int irq, void *dev_id)
+{
+	struct async_struct * info;
+
+	if (custom.serdatr & SDR_TBE) {
+#ifdef SERIAL_DEBUG_INTR
+	  printk("ser_tx_int...");
+#endif
+
+	  info = IRQ_ports;
+	  if (!info || !info->tty)
+		return IRQ_NONE;
+
+	  transmit_chars(info);
+	  info->last_active = jiffies;
+#ifdef SERIAL_DEBUG_INTR
+	  printk("end.\n");
+#endif
+	}
+	return IRQ_HANDLED;
+}
+
+/*
+ * -------------------------------------------------------------------
+ * Here ends the serial interrupt routines.
+ * -------------------------------------------------------------------
+ */
+
+/*
+ * This routine is used to handle the "bottom half" processing for the
+ * serial driver, known also the "software interrupt" processing.
+ * This processing is done at the kernel interrupt level, after the
+ * rs_interrupt() has returned, BUT WITH INTERRUPTS TURNED ON.  This
+ * is where time-consuming activities which can not be done in the
+ * interrupt driver proper are done; the interrupt driver schedules
+ * them using rs_sched_event(), and they get done here.
+ */
+
+static void do_softint(unsigned long private_)
+{
+	struct async_struct	*info = (struct async_struct *) private_;
+	struct tty_struct	*tty;
+
+	tty = info->tty;
+	if (!tty)
+		return;
+
+	if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &info->event))
+		tty_wakeup(tty);
+}
+
+/*
+ * ---------------------------------------------------------------
+ * Low level utility subroutines for the serial driver:  routines to
+ * figure out the appropriate timeout for an interrupt chain, routines
+ * to initialize and startup a serial port, and routines to shutdown a
+ * serial port.  Useful stuff like that.
+ * ---------------------------------------------------------------
+ */
+
+static int startup(struct async_struct * info)
+{
+	unsigned long flags;
+	int	retval=0;
+	unsigned long page;
+
+	page = get_zeroed_page(GFP_KERNEL);
+	if (!page)
+		return -ENOMEM;
+
+	local_irq_save(flags);
+
+	if (info->flags & ASYNC_INITIALIZED) {
+		free_page(page);
+		goto errout;
+	}
+
+	if (info->xmit.buf)
+		free_page(page);
+	else
+		info->xmit.buf = (unsigned char *) page;
+
+#ifdef SERIAL_DEBUG_OPEN
+	printk("starting up ttys%d ...", info->line);
+#endif
+
+	/* Clear anything in the input buffer */
+
+	custom.intreq = IF_RBF;
+	mb();
+
+	retval = request_irq(IRQ_AMIGA_VERTB, ser_vbl_int, 0, "serial status", info);
+	if (retval) {
+	  if (serial_isroot()) {
+	    if (info->tty)
+	      set_bit(TTY_IO_ERROR,
+		      &info->tty->flags);
+	    retval = 0;
+	  }
+	  goto errout;
+	}
+
+	/* enable both Rx and Tx interrupts */
+	custom.intena = IF_SETCLR | IF_RBF | IF_TBE;
+	mb();
+	info->IER = UART_IER_MSI;
+
+	/* remember current state of the DCD and CTS bits */
+	current_ctl_bits = ciab.pra & (SER_DCD | SER_CTS | SER_DSR);
+
+	IRQ_ports = info;
+
+	info->MCR = 0;
+	if (info->tty->termios->c_cflag & CBAUD)
+	  info->MCR = SER_DTR | SER_RTS;
+	rtsdtr_ctrl(info->MCR);
+
+	if (info->tty)
+		clear_bit(TTY_IO_ERROR, &info->tty->flags);
+	info->xmit.head = info->xmit.tail = 0;
+
+	/*
+	 * Set up the tty->alt_speed kludge
+	 */
+	if (info->tty) {
+		if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
+			info->tty->alt_speed = 57600;
+		if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
+			info->tty->alt_speed = 115200;
+		if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
+			info->tty->alt_speed = 230400;
+		if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
+			info->tty->alt_speed = 460800;
+	}
+
+	/*
+	 * and set the speed of the serial port
+	 */
+	change_speed(info, NULL);
+
+	info->flags |= ASYNC_INITIALIZED;
+	local_irq_restore(flags);
+	return 0;
+
+errout:
+	local_irq_restore(flags);
+	return retval;
+}
+
+/*
+ * This routine will shutdown a serial port; interrupts are disabled, and
+ * DTR is dropped if the hangup on close termio flag is on.
+ */
+static void shutdown(struct async_struct * info)
+{
+	unsigned long	flags;
+	struct serial_state *state;
+
+	if (!(info->flags & ASYNC_INITIALIZED))
+		return;
+
+	state = info->state;
+
+#ifdef SERIAL_DEBUG_OPEN
+	printk("Shutting down serial port %d ....\n", info->line);
+#endif
+
+	local_irq_save(flags); /* Disable interrupts */
+
+	/*
+	 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
+	 * here so the queue might never be waken up
+	 */
+	wake_up_interruptible(&info->delta_msr_wait);
+
+	IRQ_ports = NULL;
+
+	/*
+	 * Free the IRQ, if necessary
+	 */
+	free_irq(IRQ_AMIGA_VERTB, info);
+
+	if (info->xmit.buf) {
+		free_page((unsigned long) info->xmit.buf);
+		info->xmit.buf = NULL;
+	}
+
+	info->IER = 0;
+	custom.intena = IF_RBF | IF_TBE;
+	mb();
+
+	/* disable break condition */
+	custom.adkcon = AC_UARTBRK;
+	mb();
+
+	if (!info->tty || (info->tty->termios->c_cflag & HUPCL))
+		info->MCR &= ~(SER_DTR|SER_RTS);
+	rtsdtr_ctrl(info->MCR);
+
+	if (info->tty)
+		set_bit(TTY_IO_ERROR, &info->tty->flags);
+
+	info->flags &= ~ASYNC_INITIALIZED;
+	local_irq_restore(flags);
+}
+
+
+/*
+ * This routine is called to set the UART divisor registers to match
+ * the specified baud rate for a serial port.
+ */
+static void change_speed(struct async_struct *info,
+			 struct ktermios *old_termios)
+{
+	int	quot = 0, baud_base, baud;
+	unsigned cflag, cval = 0;
+	int	bits;
+	unsigned long	flags;
+
+	if (!info->tty || !info->tty->termios)
+		return;
+	cflag = info->tty->termios->c_cflag;
+
+	/* Byte size is always 8 bits plus parity bit if requested */
+
+	cval = 3; bits = 10;
+	if (cflag & CSTOPB) {
+		cval |= 0x04;
+		bits++;
+	}
+	if (cflag & PARENB) {
+		cval |= UART_LCR_PARITY;
+		bits++;
+	}
+	if (!(cflag & PARODD))
+		cval |= UART_LCR_EPAR;
+#ifdef CMSPAR
+	if (cflag & CMSPAR)
+		cval |= UART_LCR_SPAR;
+#endif
+
+	/* Determine divisor based on baud rate */
+	baud = tty_get_baud_rate(info->tty);
+	if (!baud)
+		baud = 9600;	/* B0 transition handled in rs_set_termios */
+	baud_base = info->state->baud_base;
+	if (baud == 38400 &&
+	    ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST))
+		quot = info->state->custom_divisor;
+	else {
+		if (baud == 134)
+			/* Special case since 134 is really 134.5 */
+			quot = (2*baud_base / 269);
+		else if (baud)
+			quot = baud_base / baud;
+	}
+	/* If the quotient is zero refuse the change */
+	if (!quot && old_termios) {
+		/* FIXME: Will need updating for new tty in the end */
+		info->tty->termios->c_cflag &= ~CBAUD;
+		info->tty->termios->c_cflag |= (old_termios->c_cflag & CBAUD);
+		baud = tty_get_baud_rate(info->tty);
+		if (!baud)
+			baud = 9600;
+		if (baud == 38400 &&
+		    ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST))
+			quot = info->state->custom_divisor;
+		else {
+			if (baud == 134)
+				/* Special case since 134 is really 134.5 */
+				quot = (2*baud_base / 269);
+			else if (baud)
+				quot = baud_base / baud;
+		}
+	}
+	/* As a last resort, if the quotient is zero, default to 9600 bps */
+	if (!quot)
+		quot = baud_base / 9600;
+	info->quot = quot;
+	info->timeout = ((info->xmit_fifo_size*HZ*bits*quot) / baud_base);
+	info->timeout += HZ/50;		/* Add .02 seconds of slop */
+
+	/* CTS flow control flag and modem status interrupts */
+	info->IER &= ~UART_IER_MSI;
+	if (info->flags & ASYNC_HARDPPS_CD)
+		info->IER |= UART_IER_MSI;
+	if (cflag & CRTSCTS) {
+		info->flags |= ASYNC_CTS_FLOW;
+		info->IER |= UART_IER_MSI;
+	} else
+		info->flags &= ~ASYNC_CTS_FLOW;
+	if (cflag & CLOCAL)
+		info->flags &= ~ASYNC_CHECK_CD;
+	else {
+		info->flags |= ASYNC_CHECK_CD;
+		info->IER |= UART_IER_MSI;
+	}
+	/* TBD:
+	 * Does clearing IER_MSI imply that we should disable the VBL interrupt ?
+	 */
+
+	/*
+	 * Set up parity check flag
+	 */
+
+	info->read_status_mask = UART_LSR_OE | UART_LSR_DR;
+	if (I_INPCK(info->tty))
+		info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
+	if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
+		info->read_status_mask |= UART_LSR_BI;
+
+	/*
+	 * Characters to ignore
+	 */
+	info->ignore_status_mask = 0;
+	if (I_IGNPAR(info->tty))
+		info->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
+	if (I_IGNBRK(info->tty)) {
+		info->ignore_status_mask |= UART_LSR_BI;
+		/*
+		 * If we're ignore parity and break indicators, ignore 
+		 * overruns too.  (For real raw support).
+		 */
+		if (I_IGNPAR(info->tty))
+			info->ignore_status_mask |= UART_LSR_OE;
+	}
+	/*
+	 * !!! ignore all characters if CREAD is not set
+	 */
+	if ((cflag & CREAD) == 0)
+		info->ignore_status_mask |= UART_LSR_DR;
+	local_irq_save(flags);
+
+	{
+	  short serper;
+
+	/* Set up the baud rate */
+	  serper = quot - 1;
+
+	/* Enable or disable parity bit */
+
+	if(cval & UART_LCR_PARITY)
+	  serper |= (SERPER_PARENB);
+
+	custom.serper = serper;
+	mb();
+	}
+
+	info->LCR = cval;				/* Save LCR */
+	local_irq_restore(flags);
+}
+
+static int rs_put_char(struct tty_struct *tty, unsigned char ch)
+{
+	struct async_struct *info;
+	unsigned long flags;
+
+	info = tty->driver_data;
+
+	if (serial_paranoia_check(info, tty->name, "rs_put_char"))</